The New York Central Railroad (NYC) called the 4-8-2 type of steam locomotive the Mohawk type. It was known as the Mountain type on other roads, but the New York Central did not see the name as fitting on its famous Water Level Route. Instead, it picked the name of one of those rivers its rails followed, the Mohawk River, to name its newest type of locomotive.
The L1s and L2s were unstable at higher speeds due to the lack of effective cross-balancing,[1] making the 4-wheel leading truck simply a better distributor of their weight; the L1s and L2s were consequently limited to 60mph (97km/h), though this issue was resolved for the L3s and L4s using data gathered from two experimental L-2s.
The New York Central became the largest 4-8-2 user in North America, with 600 locomotives of this type built for its service; only the Pennsylvania Railroad came close, with 301 M1's of the type.
The Mohawk type was the pre-eminent freight power of the network, displacing the 2-8-2 type from first-line service. While other roads obtained much more massive freight power, such as 2-10-0s and 2-10-4 types and a multitude of articulated designs, the New York Central, with its practically-gradeless high-speed riverside lines, needed speed over pulling power.
The 600 Mohawks delivered were divided into four main classes, plus a few experimental and prototypes that were rebuilt between 1922 and 1939.
L-1a, b, c, d
Lima-built L1c #2631 in 1930, after a bundle-type Elesco feedwater heater was added.
The first Mohawks delivered for the NYC were delivered by ALCO in 1916; these were purely freighters, with 69-inch drivers and small four axle tenders, though they would almost universally later be refitted with more six-axle examples. They would be equipped with the appropriate accouterment of the time; kerosene headlights, straight running boards, full pilots, Cole trailing trucks, and in some cases Russia iron boiler jackets.[2]
Further orders of L-1 subclasses followed in subsequent years, all built by ALCO except the L-1cs, which would be built by the Lima Locomotive Works. These engines were built with clean lines and a notable lack of appliances, though they would be modified extensively in the coming years. As with the tenders, the earlier L-1s would later be fitted with feedwater heaters, with the majority sporting Elesco bundle-type and Coffin internal feedwater heaters, though a handful of examples on the subsidiary Peoria & Eastern (as well as one on the NYC proper) had open-cycle Worthington SA type units,[3] and one each were furnished with the Elesco coil type (#2503)[4] and the external Coffin variety. The vast majority of Elesco bundle-type equipped L-1s had them installed protruding forward, as seen universally on the L-2a subclass. However, there is evidence of at least one unit (#2568) having the feedwater heater installed in the semi-sunken fashion seen on some of the Central's H-7e Mikados.[5]
One modification to the L-1s made in the 1920s was the installation of mechanical stokers, mostly of the duplex type, which were fitted universally, easing the job of the firemen. Many L-1s would also see their original fabricated Cole trailing trucks replaced with single-piece cast Deltas. Additionally, those constructed with full pilots would all have them swapped for footboard freight pilots by the 1920s. Some units would be fitted with booster-equipped trailing trucks, an invention of the New York Central's mechanical department.
185 L-1 locomotives were produced. The L-1a's were numbered 2500–2529, the L-1b's were numbered 2530–2584, the L-1c's were numbered 2585-2639 and the L-1d's were numbered 2640–2684. Interestingly, in the 1936 fleet-wide renumbering, the L-1s would remain untouched, retaining their as-built numbers.
When they were introduced in the late 1910's, the L-1s were the preeminent examples of hauling power on the New York Central, and served extensively on the main line from New York to Chicago. Gradually, as the L-2s rolled off ALCO's production line in the 1920s, many of the L-1s were displaced, with most of them stationed on the Central's Pennsylvania Division. As a consequence of the Great Depression and the associated decline in freight traffic, some were retired permanently or put into long-term storage.
By the late 1930s and the introduction of the L-3s, it was a rarity to see an L-1 outside those operating zones, where they served alongside the NE-2s, the NYC's articulated 2-6-6-2s. An exception would be the few operated by the Peoria and Eastern, which operated in Illinois and Indiana, though again they were largely limited in the scope of their travel. Much like their cousins on the Pennsylvania Division, they would last until the dieselization of the 1950s, and would all be retired by 1957.
Experimental 3-cylindered
The New York Central had two L-1 locomotives, numbered 2518 and 2605, rebuilt by ALCO in 1922 with three cylinders to help determine if the arrangement was worthwhile. They were substantially more powerful than the two-cylinder models, but it was debatable if the additional maintenance requirements of a third, central cylinder, valve gear, main rod and crank axle were worth the performance boost. In 1924, locomotive 2569 was rebuilt by Alco as a Class L-1b-3 Cylinder. The NYC must have come down on the negative side of that question, for no more were built.
L-2a, b, c, d
Preserved L-2d class locomotive Number 2933 at the Museum of Transportation in St. Louis in August, 1970
The next development of the Mohawk type for the New York Central was the L-2, 300 of its various subclasses being built between 1925 and 1930 by the American Locomotive Company. These were more modern locomotives than the L-1 class with wide boilers, long tenders, and fitted with feedwater heaters (mostly of the Elesco type and generally mounted in front of the smokebox at the top). Later L-2 subclasses, the L-2b and L-2c, had somewhat smoother lines with recessed feedwater heaters. The later L-2 locomotives, from a front-on view, appeared quite similar to the Central's fleet of Hudson passenger locomotives. The L2a's were numbered 2700–2799, the L2b's were numbered 2900–2924, the L2c's were numbered 2800-2899 and the L2d's were numbered 2925-2949 and 2950–2999. Locomotives 2995 and 2998 were modified for high-speed service in 1939.
L-3a, b, c
L-3c class locomotive number 3060 leads a freight train in Crestline, Ohio, on August 30, 1952
The next development of the Mohawk type was that of the dual-service locomotive, capable of working passenger as well as freight trains. Passenger service required the ability to work at 80mph (130km/h), as opposed to the 60mph (97km/h) required of freight. The NYC's fleet of Hudsons, 275 strong though it was, was proving inadequate to handle peak traffic demands, and some dual-purpose power would fix the problem nicely as well as giving the ability to handle express freight and mail services.
Two L-2 locomotives were given modifications for dual service work: higher boiler pressure, smaller cylinders, lightweight reciprocating parts, dynamic counterbalancing of the drivers, roller bearings on all axles and so forth. The success of these modifications prompted the construction of 65 units of the L-3 class in 1940, 25 of which were built for dual-service and the remaining 40 for freight-only; as a result, the first 25 were equipped with roller bearings on every axle while the remaining 40 had roller bearings on every axle except for the drivers. Other major difference between L-3as and L-3b/c included footboard pilots and the addition of a trailing truck booster engine used on the L-3b/c. The Class L-3a's were numbered 3000–3024, made by ALCO. The Class L-3b's were numbered 3025–3049, with ALCO producing the first ten (3025-3034) and Lima producing the remaining fifteen (3035-3049). The L-3c's were essentially 15 additional copies of the ALCO made L-3bs, numbered 3050–3064. All had oval NYC emblems under their smokebox engine number placards.
Notably, the Lima made L-3bs had a distinct smokebox front appearance, with a plated-over Elesco feedwater heater giving them their distinct look.
All L-3 locomotives were given axle-spacing that could accommodate 72" drivers, but only one was ever fitted with such. This locomotive, #3000, paved the way for the final class of Mohawks on the New York Central, the L-4. The other 64 engines received 69" drivers.
L-4a, b’s
50 L-4 locomotives were produced by the Lima Locomotive Works in 1942. None of them had booster engines, although they were built to accommodate them should they ever need to start heavy trains, but were never so modified. The L-4s were versatile locomotives, with 72" drivers, and worked the heaviest freight and passenger trains during World War II.
The L-3 and L-4 classes had large tenders riding on two six-wheel trucks that were almost as long as the locomotives hauling them, and were mostly coal space with a capacity of 43 tons; water was taken en route using the tender scoop from track pans and thus the locomotives did not need to have a large on-board water capacity. Some L-4s had Scullin Disc drivers. The L4a's and L4b's were numbered 3100-3124 and 3125–3149, respectively, and all were equipped with roller bearings on every axle. All L-4a's bore the above-described NYC "passenger" logo plates underneath their front smokebox number plates.
Many L-4 locomotives were fitted with smoke deflectors around 1945/46, after initial delivery in 1942.
Two Mohawk tenders also still exist. The tender from 2662, a class L-1d, is currently in use behind Western Maryland Scenic Railroad734 (ex-Lake Superior and Ishpeming Railroad2-8-034) in Cumberland, Maryland. The tender for L-3b 3042 was converted into a canteen and was used with Reading T-14-8-42101 during its 1976 tour with the American Freedom Train, as well as with the Chessie System Special. It was later damaged in a roundhouse fire in 1979. This water tender is currently behind L3a 3001 at the National New York Central Railroad Museum in Elkhart, Indiana. The tender was sold to the Fort Wayne Railroad Historical Society in September 2023 along with 3001.[9]
A steam locomotive is a locomotive that provides the force to move itself and other vehicles by means of the expansion of steam. It is fuelled by burning combustible material to heat water in the locomotive's boiler to the point where it becomes gaseous and its volume increases 1,700 times. Functionally, it is a steam engine on wheels.
A 2-8-8-4 steam locomotive, under the Whyte notation, has two leading wheels, two sets of eight driving wheels, and a four-wheel trailing truck. The type was generally named the Yellowstone, a name given it by the first owner, the Northern Pacific Railway, whose lines ran near Yellowstone National Park. Seventy-two Yellowstone-type locomotives were built for four U.S. railroads.
The New York Central Hudson was a popular 4-6-4 "Hudson" type steam locomotive built by the American Locomotive Company (ALCO), Baldwin Locomotive Works and the Lima Locomotive Works in three series from 1927 to 1938 for the New York Central Railroad. Named after the Hudson River, the 4-6-4 wheel arrangement came to be known as the "Hudson" type in the United States, as these locomotives were the first examples built and used in North America. Built for high-speed passenger train work, the Hudson locomotives were famously known for hauling the New York Central's crack passenger trains, such as the 20th Century Limited and the Empire State Express.
Under the Whyte notation for the classification of steam locomotives, 4-8-4 represents the wheel arrangement of four leading wheels on two axles, eight powered and coupled driving wheels on four axles and four trailing wheels on two axles. The type was first used by the Northern Pacific Railway, and initially named the Northern Pacific, but railfans and railroad employees have shortened the name since its introduction. It is most-commonly known as a Northern.
Under the Whyte notation, a 2-8-4 is a steam locomotive that has two unpowered leading wheels, followed by eight coupled and powered driving wheels, and four trailing wheels. This locomotive type is most often referred to as a Berkshire, though the Chesapeake and Ohio Railway used the name Kanawha for their 2-8-4s. In Europe, this wheel arrangement was mostly seen in mainline passenger express locomotives and, in certain countries, in tank locomotives.
The M1 was a class of steam locomotive of the Pennsylvania Railroad (PRR). It was a class of heavy mixed-traffic locomotives of the 4-8-2 "Mountain" arrangement, which uses four pairs of driving wheels with a four-wheel guiding truck in front for stability at speed and a two-wheel trailing truck to support the large firebox needed for sustained power. Although built for both passenger and freight work, they spent most of their service lives hauling heavy high-speed freight trains. Many PRR men counted the M1 class locomotives as the best steam locomotives the railroad ever owned.
The three L-10-8-8-0 Mallet steam locomotives of the Erie Railroad, built in July 1907 by ALCO, and numbered 2600, 2601 and 2602 ; were unique in that they were the only articulated camelback locomotives ever built.
The Pennsylvania Railroad's class K5 were experimental 4-6-2 "Pacific" types, built in 1929 to see if a larger Pacific than the standard K4s was worthwhile. Two prototypes were built, #5698 at the PRR's own Altoona Works, and #5699 by the Baldwin Locomotive Works. Although classified identically, the two locomotives differed in many aspects, as detailed below. They were both fitted with a much wider boiler than the K4s, but dimensionally similar to those of the I1s 2-10-0 "Decapods". Most other dimensions were enlarged over the K4s as well; the exceptions being the 70 square feet (6.5 m2) grate area and the 80 in (2.032 m) drivers.
Under the Whyte notation for the classification of steam locomotives by wheel arrangement, a 2-6-6-2 is a locomotive with one pair of unpowered leading wheels, followed by two sets of three pairs of powered driving wheels and one pair of trailing wheels. The wheel arrangement was principally used on Mallet-type articulated locomotives, although some tank locomotive examples were also built. A Garratt locomotive or Golwé locomotive with the same wheel arrangement is designated 2-6-0+0-6-2 since both engine units are pivoting.
The New York Central Railroad's Niagara was a class of 27 4-8-4 steam locomotives built by the American Locomotive Company for the New York Central Railroad. Like many railroads that adopted different names for their 4-8-4s rather than “Northerns”, the New York Central named them “Niagaras”, after the Niagara River and Falls. It is considered as one of the most efficient 4-8-4 locomotives ever built.
A steam generator is a type of boiler used to produce steam for climate control and potable water heating in railroad passenger cars. The output of a railroad steam generator is low-pressure, saturated steam that is passed through a system of pipes and conduits throughout the length of the train.
Pennsylvania Railroad Class L1s were 2-8-2 "Mikado"-type steam locomotives that were used on the Pennsylvania Railroad during the early twentieth century. These 574 locomotives were manufactured between 1914 and 1919 by the railroad's own Juniata Shops as well as the Baldwin Locomotive Works (205) and the Lima Locomotive Works (25).
New York Central 3001 is a 4-8-2 Mohawk (Mountain)-type steam locomotive built in October 1940 by American Locomotive Company (ALCO) of Schenectady, New York as a member of the L-3a class for the New York Central Railroad (NYC). Normally known as Mountain types, the NYC 4-8-2 steam locomotives were dubbed as Mohawk types after the Mohawk River, which ran alongside NYC's famed Water Level Route. Built for dual-service work, No. 3001 was used to haul both freight and passenger trains on the NYC system until being retired in February 1957.
The South African Railways Class 10B 4-6-2 of 1910 was a steam locomotive from the pre-Union era in Transvaal.
The Southern Railway Ps-4 was a class of 4-6-2 steam locomotives built for the Southern Railway (SOU), as well as its subsidiaries, the Alabama Great Southern (AGS) and the Cincinnati, New Orleans and Texas Pacific (CNO&TP). They were designed to pull SOU's heavy mainline passenger trains between Washington, D.C. and Atlanta, Georgia, including the CNO&TP trains between Cincinnati, Ohio and Jacksonville, Florida, as well as the AGS trains between Chattanooga, Tennessee and Meridian, Mississippi, via Birmingham, Alabama.
New York Central 2933 is a 4-8-2 "Mohawk" (Mountain) type steam locomotive built in 1929 by the American Locomotive Company for the New York Central Railroad. The wheel arrangement is known as the Mountain type on other railroads, but the New York Central dubbed them "Mohawks" after the Mohawk River, which the railroad followed. It pulled freight trains until being retired in 1957. As of 2024, the locomotive is on display at the National Museum of Transportation in Kirkwood, Missouri.
The Manila Railroad 200 class were 2-10-2 Santa Fe steam locomotives operated by the Manila Railroad Company (MRR), predecessor of the Philippine National Railways. They were built alongside the 4-8-2 Mountain-type 170 class by the American Locomotive Company at its Brooks facility between 1921 and 1922. During its service at the MRR, it carried heavy freight trains on the South Main Line between Manila and the Bicol Region.
The Chesapeake & Ohio Railway's Classes J-1 and J-2 were two classes of 4-8-2 steam locomotives introduced on the Chesapeake & Ohio for hauling heavy passenger trains over the Allegheny Mountains. The J-1s were the first 4-8-2s in the United States and earned the wheel arrangement the name of "Mountains" after the C&O's Mountain Divisions over which they would traverse.
Grand Trunk Western No. 6039 is a preserved class "U-1-c" 4-8-2 "Mountain type" steam locomotive built in June 1925 by Baldwin. It served the Grand Trunk Western Railroad by pulling fast passenger and freight trains throughout the Lower Peninsula of Michigan, until the railroad decided to dieselize their locomotive fleet. During that time, it was leased to the Central Vermont Railway for freight service, only to become one of the very last steam locomotives to regularly operate in the state of Vermont. After being retired in the late 1950s, No. 6039 became one of the first steam locomotives to be owned by F. Nelson Blount, and it subsequently became part of his Steamtown, U.S.A. collection for static display. In 1984, the locomotive was moved along with every other locomotive in the Steamtown collection from Bellows Falls to Scranton, Pennsylvania, where the name would late be changed to Steamtown National Historic Site under the jurisdiction of the National Park Service. As of 2023, No. 6039 remains on static display at Scranton with very meticulous cosmetic care.
Southern Pacific 786 is a preserved 2-8-2 "Mikado" type steam locomotive that was constructed at the American Locomotive Company's Brooks Works in New York. It was used to pull mainline freight trains by the Texas and New Orleans Railroad, a subsidiary of the Southern Pacific Railroad, until it was removed from service in 1955, and it was donated to the city of Austin, Texas the following year. Beginning in 1989, No. 786 was leased to the Austin Steam Train Association, who restored it to operating condition, and the locomotive was used to pull excursion trains on the Austin Western Railroad until 1999. Since 2000, crews have been performing an extensive rebuild on No. 786 to bring it back to service, and as of 2023, the rebuild continues to progress.
References
↑ Gebracht, Thomas (January 2015). "Making of a Legend - The Niagara Story"(PDF). New York Central System Historical Society Research Resources. p.13. Retrieved 28 March 2023.
Morgan, David P. (1975). "The Mohawk That Refused To Abdicate". The Mohawk That Refused to Abdicate, and Other Tales. Milwaukee: Kalmbach.[pagesneeded] Reprinted from an issue of Trains magazine some time between April 1954 and November 1958.[full citation needed]
This page is based on this Wikipedia article Text is available under the CC BY-SA 4.0 license; additional terms may apply. Images, videos and audio are available under their respective licenses.
