Pennsylvania Railroad M1 | |||||||||||||||||||||||||||||||||||||||||||||||||||
---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| |||||||||||||||||||||||||||||||||||||||||||||||||||
| |||||||||||||||||||||||||||||||||||||||||||||||||||
| |||||||||||||||||||||||||||||||||||||||||||||||||||
| |||||||||||||||||||||||||||||||||||||||||||||||||||
[1] |
The M1 was a class of steam locomotive of the Pennsylvania Railroad (PRR). It was a class of heavy mixed-traffic locomotives of the 4-8-2 "Mountain" arrangement, which uses four pairs of driving wheels with a four-wheel guiding truck in front for stability at speed and a two-wheel trailing truck to support the large firebox needed for sustained power. Although built for both passenger and freight work, they spent most of their service lives hauling heavy high-speed freight trains. Many PRR men counted the M1 class locomotives as the best steam locomotives the railroad ever owned.[ citation needed ]
A single prototype, #6699, was built in 1923 at the railroad's Altoona Works. It spent three years in testing, including all kinds of main line service as well as a session on the railroad's static test plant. Having received favorable reports, a further 200 were ordered from commercial locomotive builders; 175 from the Baldwin Locomotive Works and 25 from Lima Locomotive Works. Breaking with the PRR tradition of random locomotive numbering, these were numbered in a solid block from #6800-#6999.
In 1930, 100 more were ordered; this class M1a had several improvements. Instead of separate cylinder block and smokebox saddle castings, the M1a had a one-piece casting (first seen on the K5 Pacific) with inside steam delivery pipes, instead of the outside, visible pipes of the M1. A Worthington feedwater heater was installed, with a boxlike mixing chamber behind the stack. Twin cross-compound air compressors were hung next to each other on the left side, instead of the single compressor of the M1. The M1a locomotives had larger tenders than the previous locomotives.
The M1a locomotives were intended for passenger as well as freight service, and some bore decorative gold-leaf lining on tender and cab sides, but they proved better suited to freight work, and extensive electrification saw a surplus of K4s locomotives available for passenger trains. While they were mostly used on freight, their dual service purpose entitled them to have smokebox mounted keystone shaped numberplates. Freight engines on the Pennsy had circular numberplates.
Like most PRR steam locomotives, the M1 and M1a featured the square-shouldered Belpaire firebox. The square-topped section continued ahead of the firebox proper, revealing the presence of a combustion chamber - an extended firebox, giving more room for complete combustion of burning gases. The standard M1/M1a boiler used a working pressure of 250 pounds per square inch (1.72 MPa). 40 locomotives were later converted into class M1b; the differences were all in the boiler, those being the addition of firebox circulators —large tubes carrying water passing through the firebox space, increasing water circulation and heating area, and thus steam generation—and an increase in boiler pressure to 270 psi (1.86 MPa). The only externally visible difference was extra cleaning plugs in the firebox sides, for washing out the circulators. The M1b had greater tractive effort, thanks to the greater pressure, and more power at speed.
All were fitted with 72-inch (1.829 m) driving wheels, two 27 in × 30 in (686 mm × 762 mm) cylinders, and cast-steel KW pattern trailing trucks, similar to those fitted to K4s Pacifics. M1 and M1a tractive effort was 64,550 pounds-force (287.1 kN) while that of the M1b was 69,700 pounds-force (310.0 kN). Weight was 385,000 pounds (174.6 t). PRR standard small steel cabs were used. A spotting feature was a large cross-mounted air tank at the front of the locomotive above the pilot. There was a family resemblance with other PRR locomotives. After World War II, the M1 locomotives underwent similar front-end changes to those made to the K4s, including sheet steel drop-coupler pilots, the moving of the headlight to the smokebox top in front of the stack, the moving of the steam-driven generator to the smokebox front for easier maintenance, and the addition of a wide step above the air tank to service the air compressor.
A variety of tenders were fitted to M1 locomotives, of steadily-increasing size. During later years some hauled sixteen-wheel 210-F-75B tenders almost as long as the locomotives themselves. All were fitted with scoops to pick up water from track pans. On the rear tender decks, all were later fitted with "doghouses" for the head-end brakeman on freight trains, giving him a view backward over the train and placing him out of the way of the engineer and fireman. Many had railing-like trainphone antennas added during the 1940s.
As dieselization progressed, the M1 locomotives were assigned to heavier trains, while the diesels were assigned the high-speed freight trains that were previously the M1s' preserve. Their final years of service saw them hauling heavier trains than ever. Many remained in service until the withdrawal of steam from the PRR in mid-1957.
One locomotive, M1b #6755, was saved from the scrapper's torch for the PRR's historical collection housed at Northumberland, Pennsylvania. It is now in the possession of the Railroad Museum of Pennsylvania, in Strasburg, PA. It was added to the National Register of Historic Places in 1979 as Locomotive No. 6755 .
The tender of M1 #6659, minus the engine, has also been preserved and was purchased by the Pennsylvania Railroad T1 Steam Locomotive Trust in August, 2017. The tender will be restored for eventual use behind the new-build T1 class locomotive #5550. [2] [3]
The Pennsylvania Railroad, legal name The Pennsylvania Railroad Company, also known as the "Pennsy", was an American Class I railroad that was established in 1846 and headquartered in Philadelphia, Pennsylvania. At its peak in 1882, the Pennsylvania Railroad was the largest railroad, the largest transportation enterprise, and the largest corporation in the world.
The Pennsylvania Railroad K4 was a class of 425 4-6-2 steam locomotives built between 1914 and 1928 for the PRR, where they served as the primary main line passenger steam locomotives on the entire PRR system until late 1957.
The Pennsylvania Railroad (PRR) class T1 duplex-drive 4-4-4-4 steam locomotives, introduced in 1942 with two prototypes and later in 1945-1946 with 50 production examples, were the last steam locomotives built for the PRR and arguably its most controversial. They were ambitious, technologically sophisticated, powerful, fast and distinctively streamlined by Raymond Loewy. However, they were also prone to wheelslip both when starting and at speed, in addition to being complicated to maintain and expensive to run. The PRR decided in 1948 to place diesel locomotives on all express passenger trains, leaving unanswered questions as to whether the T1's flaws were solvable, especially taking into account that the two prototypes did not have the problems inherent to the production units.
A 4-4-4-4 steam locomotive, in the Whyte notation for describing locomotive wheel arrangements, has a four-wheel leading truck, two sets of four driving wheels, and a four-wheel trailing truck. While it would be possible to make an articulated locomotive of this arrangement, the only 4-4-4-4s ever built were duplex locomotives—with two sets of cylinders driving two sets of driven wheels in one rigid frame, essentially a 4-8-4 with divided drive.
The Pennsylvania Railroad's class B6 was its most successful class of switcher locomotive, or as the PRR termed them "shifter". The PRR preferred the 0-6-0 wheel arrangement for larger switchers, whereas on other railroads the 0-8-0 gained preference. The PRR generally used 2-8-0s when larger power was required.
The Pennsylvania Railroad's S2 class was a steam turbine locomotive designed and built in a collaborative effort by Baldwin Locomotive Works and Westinghouse Electric & Manufacturing Company, as an attempt to prolong the dominance of the steam locomotive by adapting technology that had been widely accepted in the marine industry. One was built, #6200, delivered in September 1944. The S2 was the sole example of the 6-8-6 wheel arrangement in the Whyte notation, with a six-wheel leading truck keeping the locomotive stable at speed, eight powered and coupled driving wheels, and a six-wheel trailing truck supporting the large firebox. The S2 used a direct-drive steam turbine provided by the Westinghouse Electric & Manufacturing Company, geared to the center pair of axles with the outer two axles connected by side rods; the fixed gear ratio was 18.5:1. Such design was to prevent energy loss and S2 achieved a mechanical efficiency of 97% which means only 3% of steam energy was lost within the propulsion equipment. The disadvantage of a direct-drive steam turbine was that the turbine could not operate at optimal speeds over the locomotive's entire speed range. The S2 was the largest, heaviest and fastest direct-drive turbine locomotive design ever built.
The Pennsylvania Railroad's class K5 were experimental 4-6-2 "Pacific" types, built in 1929 to see if a larger Pacific than the standard K4s was worthwhile. Two prototypes were built, #5698 at the PRR's own Altoona Works, and #5699 by the Baldwin Locomotive Works. Although classified identically, the two locomotives differed in many aspects, as detailed below. They were both fitted with a much wider boiler than the K4s, but dimensionally similar to those of the I1s 2-10-0 "Decapods". Most other dimensions were enlarged over the K4s as well; the exceptions being the 70 square feet (6.5 m2) grate area and the 80 in (2.032 m) drivers.
The PRR S1 class steam locomotive was a single experimental duplex locomotive of the Pennsylvania Railroad. It was designed to demonstrate the advantages of duplex drives espoused by Baldwin Chief Engineer Ralph P. Johnson. The S1 class was the largest steam locomotive ever built. The streamlined Art Deco styled shell of the locomotive was designed by Raymond Loewy.
The Pennsylvania Railroad class Q1, #6130, was a single experimental steam locomotive designed for dual service. The locomotive entered service in 1942, and retired in 1949 after accumulating a relatively low 165,000 service miles.
The Pennsylvania Railroad's class N2sa comprised rebuilds to PRR practice of the 130 USRA Heavy Santa Fe steam locomotives the railroad received under the auspices of the United States Railroad Administration, the nationalized central control of the nation's railroads during World War I. These locomotives, as received, were classified N2s. Rebuilds began from 1923 and all locomotives were rebuilt, classified N2sa after the rebuild. They received a Belpaire firebox, the PRR-standard smokebox front, a raised headlight following PRR practice, and the bell moved from smokebox front to boiler top. Brakemen's "doghouse" shacks were built on the rear tender decks.
Pennsylvania Railroad Class L1s were 2-8-2 "Mikado"-type steam locomotives that were used on the Pennsylvania Railroad during the early twentieth century. These 574 locomotives were manufactured between 1914 and 1919 by the railroad's own Juniata Shops as well as the Baldwin Locomotive Works (205) and the Lima Locomotive Works (25).
The PRR J1 was a class of 2-10-4 "Texas" type steam locomotives built between 1942 and 1944. The J1 had over 95,000 pounds-force (422.6 kN) of tractive effort, plus an additional 15,000 lbf (66.7 kN) if the booster engine was used.
Pennsylvania Railroad 1361 is a 4-6-2 K4 "Pacific" type steam locomotive built in May 1918 by the Pennsylvania Railroad's (PRR) Juniata Shops in Altoona, Pennsylvania. It hauled mainline passenger trains in Pennsylvania and commuter trains in Central New Jersey on the PRR until its retirement from revenue service in 1956. Restored to operating condition for excursion service in 1987, No. 1361 and its only surviving sister locomotive, No. 3750, were designated as the official state steam locomotives by the Pennsylvania General Assembly. In late 1988, it was sidelined due to mechanical problems and was currently owned by the Railroaders Memorial Museum (RMM) in Altoona, Pennsylvania, who were currently getting No. 1361 back to operation.
Pennsylvania Railroad 1737 was a 4-6-2 Pacific type K4 class steam locomotive built in 1914 as the first of its class and would haul heavier passenger trains that the smaller E class 4-4-2 Atlantics could not handle such as the PRR's flagship passenger train, the Broadway Limited. In the 1930s, as the PRR had increased passenger service time tables, the trains became longer and heavier than a single K4s could handle, necessitating double-heading with a second engine. The "Standard Railroad Of The World" made attempts to replace the 1737 and its classmates with larger, more powerful classes including: K5, S1, and the T1, none of which were successful; thus, the K4s continued hauling passenger trains until the Pennsylvania Railroad replaced steam locomotives with the increasingly-popular and less-costly diesel-electric locomotives in 1957.
The Pennsylvania Railroad G5 is a class of 4-6-0 steam locomotives built by the PRR's Juniata Shops in the mid-late 1920s. It was designed for passenger trains, particularly on commuter lines, and became a fixture on suburban railroads until the mid-1950s.
The Pennsylvania Railroad's class E2, E3, E7 steam locomotives were of the 4-4-2 "Atlantic" passenger type, frequently called light Atlantics after the introduction of the heavier E6 Atlantics. All were similar in size and boiler capacity but differed in firebox type, valves and valve gear and cylinder diameter. Classes E2 and E3 were built simultaneously.
Pennsylvania Railroad 6755 is a 4-8-2 "Mountain" type steam locomotive built in 1930 for the Pennsylvania Railroad by the railroad's own Altoona Works as a member of the M1b locomotive class for mainline freight service. Retired from commercial service in 1957, the locomotive was preserved by the Pennsylvania Railroad and was placed on display at the Railroad Museum of Pennsylvania in Strasburg, Pennsylvania. The 6755 is the only M1 class locomotive to have survived into preservation.
A duplex locomotive is a steam locomotive that divides the driving force on its wheels by using two pairs of cylinders rigidly mounted to a single locomotive frame; it is not an articulated locomotive. The concept was first used in France in 1863, but was particularly developed in the early 1930s by the Baldwin Locomotive Works, the largest commercial builder of steam locomotives in North America, under the supervision of its then chief engineer, Ralph P. Johnson.
Pennsylvania Railroad 5550 is a mainline duplex drive steam locomotive under construction in the United States. With an estimated completion by 2030, the locomotive will become the 53rd example of the Pennsylvania Railroad's T1 steam locomotive class and the only operational locomotive of its type, as well as the largest steam locomotive built in the United States since 1952. The estimated cost of PRR 5550 was originally $10 million, but an updated projected cost of $7 million was released with the acquisition of an existing long-haul tender from the Western New York Railway Historical Society in August 2017. Construction began in 2014 with the casting of the locomotive's keystone-shaped number plate. As of February 2024 the locomotive was 43% complete.
The Pennsylvania Railroad's class K29s comprised a single experimental 4-6-2 "Pacific" type steam locomotive. Constructed by Alco-Schenectady, it was given road number 3395. Although only one demonstrator was constructed, the K29s would become the basis for the highly successful K4s Pacifics and L1s Mikados. The lone example spent most of its life on the PRR's Pittsburgh division main line and was retired around 1929.