Urban canyon

Last updated
W42nd Street canyon jeh.JPG
An urban canyon at 42nd Street, Midtown Manhattan, New York City
42nd Street in Tudor City.jpg
The same Manhattan street seen from within, with many buildings much taller than the width of the road

An urban canyon (also known as a street canyon or skyscraper canyon) is a place where the street is flanked by buildings on both sides creating a canyon-like environment, evolved etymologically from the Canyon of Heroes in Manhattan. Such human-built canyons are made when streets separate dense blocks of structures, especially skyscrapers. Other examples include the Magnificent Mile in Chicago, Los Angeles' Wilshire Boulevard corridor, Toronto's Financial District, and Hong Kong's Kowloon and Central districts.

Contents

Urban canyons affect various local conditions, including temperature, wind, light, air quality, and radio reception, including satellite navigation signals.

Geometry and classification

Ideally an urban canyon is a relatively narrow street with tall, continuous buildings on both sides of the road. But now the term urban canyon is used more broadly, and the geometrical details of the street canyon are used to categorize them. The most important geometrical detail about a street canyon is the ratio of the canyon height (H) to canyon width (W), H/W, which is defined as the aspect ratio. The value of the aspect ratio can be used to classify street canyons as follows: [1]

A sub-classification of each of the above can be done depending on the distance between two major intersections along the street, defined as the length (L) of the street canyon:

Another classification is based on the symmetry of the canyon:

Another specific type is:

The effect of a street canyon on local wind and air quality can greatly differ in different canyon geometries and this will be discussed in detail in sections below.

Other important factors taken into account in studies of urban canyons are the air volume, orientation of the canyon (north–south, east–west etc.) and the sky view factor. The air volume of the street canyon is the air contained within the buildings on either side which act as walls, the street which is the bottom boundary, and an imaginary upper boundary at roof level called the 'lid' of the canyon.

The sky view factor (SVF) denotes the ratio between radiation received by a planar surface and that from the entire hemispheric radiating environment [2] and is calculated as the fraction of sky visible from the ground up. SVF is a dimensionless value that ranges from 0 to 1. A SVF of 1 means that the sky is completely visible, for example, in a flat terrain. When a location has buildings and trees, it will cause the SVF to decrease proportionally. [3]

Effects

Near the equinoxes, sunrises and sunsets align with in east-west urban street canyons, an event known as Chicagohenge (pictured). In other cities, similar phenomenon with names such as Manhattanhenge occur at various times of the year. 20240920 6-41PM stacked R6 0341-0343 rotated 15.56 crop.jpg
Near the equinoxes, sunrises and sunsets align with in east-west urban street canyons, an event known as Chicagohenge (pictured). In other cities, similar phenomenon with names such as Manhattanhenge occur at various times of the year.

The modification of the characteristics of the atmospheric boundary layer by the presence of a street canyon is called the street canyon effect. As mentioned earlier, street canyons affect temperature, wind speed and wind direction and consequently the air quality within the canyon.

Temperature

Urban canyons contribute to the urban heat island effect. The temperature inside the canyon can be elevated 2–4 °C. Studies of temperature phenomena consider irradiance, angle of incidence, surface albedo, emissivity, temperature and SVF. For a high SVF, the urban canyons cool quickly, because more sky is available to absorb the heat retained by the buildings. With a low SVF, the canyon can retain more heat during the day, creating a higher heat release at night. A study done by Nunez and Oke investigated the energy exchanges in an urban canyon in mid-latitudes in fine summer weather. [3] The study showed that the amount of surface energy at various times within the canyon depends on canyon geometry and orientation. Canyons with north–south orientation were found to have the floor being the most active energy site. In such a canyon, 30% of midday radiant surplus is stored in the canyon materials (the buildings). At night, the net radiant deficit (meaning the lack of solar radiation) is countered by the release of energy that was being stored in the canyon materials. This phenomenon contributes heavily to the urban heat island effect.

Wind

Street canyons can modify both the speed and the direction of winds. The vertical wind velocity approaches zero at the roof level of the canyon. Shear production and dissipation are high at the roof level and a strong thin shear layer is created at the building height. [4] Turbulence kinetic energy is higher near the downwind building than near the upwind building because of stronger wind shears. The resulting flow patterns inside the canyon depend on the wind direction with respect to the street orientation direction.

Wind parallel to canyon

When the roof level/background wind direction is parallel to the street, a channelization effect is seen where winds tend to be channeled and accelerated through the canyon. Where the street width is non-uniform, a Venturi effect is seen when winds funnel through small openings, further enhancing the acceleration of winds. [5] Both these effects are explained by the Bernoulli's principle. The along-street wind and transport can be significantly different for short and long canyons as the corner vortices have a stronger influence in short canyons. [6]

Wind perpendicular to canyon

When the roof level/background wind direction is perpendicular to the street, a vertically rotating wind flow is created with a centered primary vortex inside street canyons. Based on the aspect ratio, different flow regimes are defined in street canyons. In the increasing order of aspect ratio these flow regimes are: isolated roughness flow, wake interference flow and skimming flow. [7] The total number of vortices made and their intensities depends on many factors. Numerical model studies done for isolated street canyons have shown that the number of vortexes made increases with increasing aspect ratio of the canyon. But there is a critical value of the ambient wind speed, above which the number and pattern of vortexes become independent of the aspect ratio. [8]

The comparison of (a) isolated roughness flow and (b) skimming flow regimes in a street canyon (after Oke, 1988) Flow regimes in a street canyon.png
The comparison of (a) isolated roughness flow and (b) skimming flow regimes in a street canyon (after Oke, 1988)

Numerical and wind tunnel studies have shown that for symmetric canyons with an aspect ratio = 0.5, a ground level secondary vortex can be seen near the leeward side building wall. For symmetric canyons with aspect ratio ≥ 1.4, a weaker ground level secondary vortex can be seen near the windward side building wall and for aspect ratio ≥ 2 secondary vortexes are seen right below the primary vortex. [8] [9] In asymmetric and step-up canyons the formation of secondary vortexes can be more common. Wind tunnel studies have shown that, in a step-up canyon where the upwind building is shorter, a stagnation point can be identified on the windward face of the taller building. The region below this stagnation point is called the interaction region, since all streamlines in this region are deflected downward into the street canyon. The characteristics of the vortex flow patterns inside the canyon strongly depend the height ratio of buildings on either side of the canyon. For a downwind building height Hd to upwind building height Hu ratio of 3, a single primary vortex has been observed. But for Hd/Hu=1.67, counter-rotating vortexes can occupy the whole depth of the canyon. [10]

Other factors that have an effect on the strength of this re-circulation flow are traffic induced turbulence and roof shapes of the buildings. Physical model studies have shown that two way traffics increases the turbulence in the lower half of the canyon and that pitched roof on either side of the canyon shifts the main area of turbulent production downstream and reduced the intensity of the re-circulation flow inside the canyon. [11]

In the skimming flow regime, the wind vortex made inside a street canyon, when mean wind direction is perpendicular to the street (after Oke, 1988) A wind vortex inside a street canyon.png
In the skimming flow regime, the wind vortex made inside a street canyon, when mean wind direction is perpendicular to the street (after Oke, 1988)

Under these perpendicular wind conditions, mainly at the street level, at each end of the canyon, horizontally rotating corner/end vortexes are made. The horizontal extent of these corner vortexes are different at each end of a canyon and this leads complex surface level wind patterns at intersections. Field experiments have further shown that corner vortexes can extend in the whole depth of canyon but with changing horizontal extent with height. [12]

The structure of the neighboring area of a street canyon; for instance a series of street canyons, add more complexity to flow field.

All the above-mentioned results are for situations with no heating effects. A numerical model study have shown that, when a surface in a street canyons heats up, it changes the characteristics of the vortex flow. And heating of different surfaces; upwind wall, downwind wall, canyon floor, changes the vortex flow in different manners. [8]

Air quality

The modification of temperature and wind by the presence of a street canyon, consequently affect the air quality inside the street canyon. When the direction of the mean wind is parallel to the street, the channelization and Venturi effects described above, increases the dispersion of pollutants inside the street canyon. This often act to 'flush out' the air pollutants [5] and increase the air quality inside the street canyon. But in instances where air pollutant sources are present upwind, channeling winds could transport pollutants to downwind locations far from the source and contribute to bad quality at the downwind locations.

When the mean wind direction is perpendicular to the street, the vortex flow formed inside the canyon acts to confine air flow, reduce dispersion of pollutants and increase the pollution concentrations inside the street canyon. Pollution from local source inside the canyon and also pollution entrained in to the canyon from the mean wind flow, is carried by the vortex flow and is re-circulated within the canyon. In urban environments, vehicle tail pipe emissions are the major source of many air pollutants such as ultrafine particles, fine particles, carbon dioxide, NOx. These pollution plumes created on the street, at the surface level, are pushed toward the lee side of the canyon by the vortex flow, making the surface level pollution concentrations much higher at the leewardside of the street compared to the windward side. Secondary vortexes in the lower portion of the canyon can further act to stagnate pollutants on the side walks; specially on the leeward side. One field study has reported ultrafine particle concentrations four times higher on the leeward side sidewalk compared to the windward side. [13]

GPS signal reception

When using GPS receivers in street canyons with tall buildings, the shadowing and multipath effects may contribute to poor GPS signal reception. [14]

See also

Related Research Articles

<span class="mw-page-title-main">Urban heat island</span> Situation where cities are warmer than surrounding areas

Urban areas usually experience the urban heat island (UHI) effect, that is, they are significantly warmer than surrounding rural areas. The temperature difference is usually larger at night than during the day, and is most apparent when winds are weak, under block conditions, noticeably during the summer and winter. The main cause of the UHI effect is from the modification of land surfaces while waste heat generated by energy usage is a secondary contributor. Urban areas occupy about 0.5% of the Earth's land surface but host more than half of the world's population. As a population center grows, it tends to expand its area and increase its average temperature. The term heat island is also used; the term can be used to refer to any area that is relatively hotter than the surrounding, but generally refers to human-disturbed areas.

<span class="mw-page-title-main">Wind tunnel</span> Machine used for studying the effects of air moving around objects

Wind tunnels are machines in which objects are held stationary inside a tube, and air is blown around it to study the interaction between the object and the moving air. They are used to test the aerodynamic effects of aircraft, rockets, cars, and buildings. Different wind tunnels range in size from less than a foot across, to over 100 feet (30 m), and can have air that moves at speeds from a light breeze to hypersonic velocities.

<span class="mw-page-title-main">Airfield traffic pattern</span> Standard aircraft path

An airfield traffic pattern is a standard path followed by aircraft when taking off or landing while maintaining visual contact with the airfield.

<span class="mw-page-title-main">Orographic lift</span> Air mass forced upwards as it moves over rising terrain

Orographic lift occurs when an air mass is forced from a low elevation to a higher elevation as it moves over rising terrain. As the air mass gains altitude it quickly cools down adiabatically, which can raise the relative humidity to 100% and create clouds and, under the right conditions, precipitation.

In common usage, wind gradient, more specifically wind speed gradient or wind velocity gradient, or alternatively shear wind, is the vertical component of the gradient of the mean horizontal wind speed in the lower atmosphere. It is the rate of increase of wind strength with unit increase in height above ground level. In metric units, it is often measured in units of meters per second of speed, per kilometer of height (m/s/km), which reduces inverse milliseconds (ms−1), a unit also used for shear rate.

<span class="mw-page-title-main">Lee wave</span> Atmospheric stationary oscillations

In meteorology, lee waves are atmospheric stationary waves. The most common form is mountain waves, which are atmospheric internal gravity waves. These were discovered in 1933 by two German glider pilots, Hans Deutschmann and Wolf Hirth, above the Giant Mountains. They are periodic changes of atmospheric pressure, temperature and orthometric height in a current of air caused by vertical displacement, for example orographic lift when the wind blows over a mountain or mountain range. They can also be caused by the surface wind blowing over an escarpment or plateau, or even by upper winds deflected over a thermal updraft or cloud street.

<span class="mw-page-title-main">Windbreak</span> Rows of trees or shrubs planted to provide shelter from the wind

A windbreak (shelterbelt) is a planting usually made up of one or more rows of trees or shrubs planted in such a manner as to provide shelter from the wind and to protect soil from erosion. They are commonly planted in hedgerows around the edges of fields on farms. If designed properly, windbreaks around a home can reduce the cost of heating and cooling and save energy. Windbreaks are also planted to help keep snow from drifting onto roadways or yards. Farmers sometimes use windbreaks to keep snow drifts on farm land that will provide water when the snow melts in the spring. Other benefits include contributing to a microclimate around crops, providing habitat for wildlife, and, in some regions, providing wood if the trees are harvested.

<span class="mw-page-title-main">Planetary boundary layer</span> Lowest part of the atmosphere directly influenced by contact with the planetary surface

In meteorology, the planetary boundary layer (PBL), also known as the atmospheric boundary layer (ABL) or peplosphere, is the lowest part of the atmosphere and its behaviour is directly influenced by its contact with a planetary surface. On Earth it usually responds to changes in surface radiative forcing in an hour or less. In this layer physical quantities such as flow velocity, temperature, and moisture display rapid fluctuations (turbulence) and vertical mixing is strong. Above the PBL is the "free atmosphere", where the wind is approximately geostrophic, while within the PBL the wind is affected by surface drag and turns across the isobars.

In fluid dynamics, a Kármán vortex street is a repeating pattern of swirling vortices, caused by a process known as vortex shedding, which is responsible for the unsteady separation of flow of a fluid around blunt bodies.

<span class="mw-page-title-main">Wingtip vortices</span> Turbulence caused by difference in air pressure on either side of wing

Wingtip vortices are circular patterns of rotating air left behind a wing as it generates lift. The name is a misnomer because the cores of the vortices are slightly inboard of the wing tips. Wingtip vortices are sometimes named trailing or lift-induced vortices because they also occur at points other than at the wing tips. Indeed, vorticity is trailed at any point on the wing where the lift varies span-wise ; it eventually rolls up into large vortices near the wingtip, at the edge of flap devices, or at other abrupt changes in wing planform.

<span class="mw-page-title-main">Airshed</span>

An airshed is a geographical area where local topography and meteorology limit the dispersion of pollutants away from the area. They are formed by air masses moving across a landscape, thus influencing the atmospheric composition of that area. Their boundaries are loosely defined, but can be quantified. Airborne chemicals disperse throughout an airshed and enter bodies of water in the area.

<span class="mw-page-title-main">Windcatcher</span> Architectural element for creating a draft

A windcatcher, wind tower, or wind scoop is a traditional architectural element, originated in Iran (Persia), used to create cross ventilation and passive cooling in buildings. Windcatchers come in various designs, depending on whether local prevailing winds are unidirectional, bidirectional, or multidirectional, on how they change with altitude, on the daily temperature cycle, on humidity, and on how much dust needs to be removed. Despite the name, windcatchers can also function without wind.

Urban climatology is the study of urban climate. It is a branch of climatology that concerns interactions between urban areas and the atmosphere, the effects they have on one another, and the varying spatial and temporal scales at which these processes occur.

<span class="mw-page-title-main">Eddy (fluid dynamics)</span> Swirling of a fluid and the reverse current created when the fluid is in a turbulent flow regime

In fluid dynamics, an eddy is the swirling of a fluid and the reverse current created when the fluid is in a turbulent flow regime. The moving fluid creates a space devoid of downstream-flowing fluid on the downstream side of the object. Fluid behind the obstacle flows into the void creating a swirl of fluid on each edge of the obstacle, followed by a short reverse flow of fluid behind the obstacle flowing upstream, toward the back of the obstacle. This phenomenon is naturally observed behind large emergent rocks in swift-flowing rivers.

<span class="mw-page-title-main">Roadway air dispersion modeling</span> Study of air pollutant transport from a roadway

Roadway air dispersion modeling is the study of air pollutant transport from a roadway or other linear emitter. Computer models are required to conduct this analysis, because of the complex variables involved, including vehicle emissions, vehicle speed, meteorology, and terrain geometry. Line source dispersion has been studied since at least the 1960s, when the regulatory framework in the United States began requiring quantitative analysis of the air pollution consequences of major roadway and airport projects. By the early 1970s this subset of atmospheric dispersion models was being applied to real-world cases of highway planning, even including some controversial court cases.

The following outline is provided as an overview of and topical guide to air pollution dispersion: In environmental science, air pollution dispersion is the distribution of air pollution into the atmosphere. Air pollution is the introduction of particulates, biological molecules, or other harmful materials into Earth's atmosphere, causing disease, death to humans, damage to other living organisms such as food crops, and the natural or built environment. Air pollution may come from anthropogenic or natural sources. Dispersion refers to what happens to the pollution during and after its introduction; understanding this may help in identifying and controlling it.

<span class="mw-page-title-main">Horizontal convective rolls</span> Long rolls of counter-rotating air

Horizontal convective rolls, also known as horizontal roll vortices or cloud streets, are long rolls of counter-rotating air that are oriented approximately parallel to the ground in the planetary boundary layer. Although horizontal convective rolls, also known as cloud streets, have been clearly seen in satellite photographs for the last 30 years, their development is poorly understood, due to a lack of observational data. From the ground, they appear as rows of cumulus or cumulus-type clouds aligned parallel to the low-level wind. Research has shown these eddies to be significant to the vertical transport of momentum, heat, moisture, and air pollutants within the boundary layer. Cloud streets are usually more or less straight; rarely, cloud streets assume paisley patterns when the wind driving the clouds encounters an obstacle. Those cloud formations are known as von Kármán vortex streets.

<span class="mw-page-title-main">Forces on sails</span>

Forces on sails result from movement of air that interacts with sails and gives them motive power for sailing craft, including sailing ships, sailboats, windsurfers, ice boats, and sail-powered land vehicles. Similar principles in a rotating frame of reference apply to windmill sails and wind turbine blades, which are also wind-driven. They are differentiated from forces on wings, and propeller blades, the actions of which are not adjusted to the wind. Kites also power certain sailing craft, but do not employ a mast to support the airfoil and are beyond the scope of this article.

<span class="mw-page-title-main">Cross ventilation</span> Movement of air through a building

Cross ventilation is a natural phenomenon where wind, fresh air or a breeze enters upon an opening, such as a window, and flows directly through the space and exits through an opening on the opposite side of the building. This produces a cool stream of air and as well as a current across the room from the exposed area to the sheltered area.

References

  1. ↑ Vardoulakis, Sotiris; Bernard E.A. Fisher; Koulis Pericleous; Norbert Gonzalez-Flesca (2003). "Modelling air quality in street canyons: a review" (PDF). Atmospheric Environment. 37 (2): 155–182. Bibcode:2003AtmEn..37..155V. doi:10.1016/s1352-2310(02)00857-9. S2CID   55939985.
  2. ↑ Watson, I. D; G. T. Johnson (March–April 1987). "Graphical estimation of sky view-factors in urban environments". Journal of Climatology. 7 (2): 193–197. Bibcode:1987IJCli...7..193W. doi:10.1002/joc.3370070210.
  3. 1 2 Nunez, M; T. R. Oke (1977). "The Energy Balance of an Urban Canyon". Journal of Applied Meteorology. 16 (1): 11–19. Bibcode:1977JApMe..16...11N. doi:10.1175/1520-0450(1977)016<0011:teboau>2.0.co;2. hdl: 2429/35946 .
  4. ↑ Lien, F.S.; E. Yee; Y. Cheng (2004). "Simulation of mean flow and turbulence over a 2D building array using high-resolution CFD and a distributed drag force approach". Journal of Wind Engineering and Industrial Aerodynamics. 92 (2): 117–158. doi:10.1016/j.jweia.2003.10.005.
  5. 1 2 Spirn, Anne Whiston (June 1986). "AIR QUALITY AT STREET-LEVEL: STRATEGIES FOR URBAN DESIGN". Prepared for: Boston Redevelopment Authority.
  6. ↑ Kastner-Klein, P; E. Fedorovich; M. W. Rotach (2001). "A wind-tunnel study of organized and turbulent air motions in urban street canyons". Journal of Wind Engineering and Industrial Aerodynamics. 89 (9): 849–861. CiteSeerX   10.1.1.542.6044 . doi:10.1016/s0167-6105(01)00074-5.
  7. ↑ Oke, T.R (1988). "Street design and urban canopy layer climate". Energy and Buildings. 11 (1–3): 103–113. doi:10.1016/0378-7788(88)90026-6.
  8. 1 2 3 Kim, J.J.; J. J. Baik (1999). "A numerical study of thermal effects on flow and pollutant dispersion in urban street canyons". Journal of Applied Meteorology. 38 (9): 1249–1261. Bibcode:1999JApMe..38.1249K. doi: 10.1175/1520-0450(1999)038<1249:ansote>2.0.co;2 .
  9. ↑ Kovar-Panskus, A (2002). "Influence of Geometry on the Mean Flow within Urban Street Canyons — A Comparison of Wind Tunnel Experiments and Numerical Simulations". Urban Air Quality — Recent Advances. pp. 365–380. doi:10.1007/978-94-010-0312-4_26. ISBN   978-94-010-3935-2.
  10. ↑ Addepalli, Bhagirath; Eric R. Pardyjak (2013). "Investigation of the Flow Structure in Step-Up Street Canyons—Mean Flow and Turbulence Statistics". Boundary-Layer Meteorology. 148 (1): 133–155. Bibcode:2013BoLMe.148..133A. doi:10.1007/s10546-013-9810-5. S2CID   120763318.
  11. ↑ Kastner-Klein, P; R. Berkowicz; R. Britter (2004). "The influence of street architecture on flow and dispersion in street canyons". Meteorology and Atmospheric Physics. 87 (1–3): 121–131. Bibcode:2004MAP....87..121K. doi:10.1007/s00703-003-0065-4. S2CID   123693211.
  12. ↑ Pol, S.U.; M.Brown (May 2008). "Flow Patterns at the Ends of a Street Canyon: Measurements from the Joint Urban 2003 Field Experiment". Journal of Applied Meteorology and Climatology. 47 (5): 1413. Bibcode:2008JApMC..47.1413P. doi: 10.1175/2007JAMC1562.1 . S2CID   121902366.
  13. ↑ Pirjola, L.; Lähde, T.; Niemi, J.V.; Kousa, A.; Rönkkö, T.; Karjalainen, P.; Keskinen, J.; Frey, A.; Hillamo, R. (2012). "Spatial and temporal characterization of traffic emissions in urban microenvironments with a mobile laboratory". Atmospheric Environment. 63: 156. Bibcode:2012AtmEn..63..156P. doi:10.1016/j.atmosenv.2012.09.022.
  14. ↑ MISRA, P., P. ENGE (2006). Global Positioning System: Signals, Measurements, and Performance, Second Edition. Lincoln (MA), U.S.A: Ganga-Jamuna Press.{{cite book}}: CS1 maint: multiple names: authors list (link)
This page is based on this Wikipedia article
Text is available under the CC BY-SA 4.0 license; additional terms may apply.
Images, videos and audio are available under their respective licenses.