GR connector

Last updated
GR-874
Gr-874-connector.jpg
Type RF coaxial connector
Production history
Designed 1947-1948
Manufacturer General Radio
Cable Coaxial

The GR connector, officially the General Radio Type 874, was a type of RF connector used for connecting coaxial cable. Designed by Eduard Karplus, Harold M. Wilson and William R. Thurston at General Radio Corporation. [1] It was widely used on General Radio's electronic test equipment and some Tektronix instruments from the 1950s to the 1970s. [2]

The connector had several desirable properties:

This last characteristic was achieved by having both the inner and outer conductors made from four leaves, two of which were displaced slightly outwards and two of which were displaced slightly inwards. By rotating one connector by 90 degrees, its inner leaves would mate with the other connector's outer leaves and vice versa.

When frequently mated, the inner leaves were susceptible to breakage due to stubbing, flexing and fatigue cracking as the connector was pressed together and alignment was perfected.

In 1961, an optional locking mechanism consisting of an outer hex nut encasing a captured threaded barrel was added to the 874 line. [3] It can be seen in the photograph of a GR-900 to GR-874 adapter. [4] The locking assembly is not captive and can be backed off the RF connector. The threaded barrel is supplied on each connector. The threaded barrel was withdrawn into the nut on one connector and extended on the other to allow the barrel to engage the nut of both mating connectors. This style of locking mechanism was continued in GR-874's thematic successors; the GR-900 precision 14 mm connector that retains a crenelated hermaphroditic mechanical anti-spin feature to protect the sexless RF interface from rotating and galling when the locking mechanism is tightened, and the fully sexless APC-7 7 mm connector.

Adapters to other connector series were available.

Eventually, the limited frequency range of a 14 mm connector and its high manufacturing cost overcame its ease of assembly and the GR-874 was supplanted generally by the 7 mm type N connector and its variants, the BNC connector and the TNC connector, and the later higher frequency 3.5 mm SMA connectors. General Radio, then still a major source of RF test equipment, designed the incompatible GR-900 as a 14 mm successor to the GR-874, filling the industry's need for a higher performance sexless connector for fully reversible lab standards and related test equipment. The GR-900 was in turn succeeded in this essential niche role by the completely sexless APC-7 connector.

Related Research Articles

<span class="mw-page-title-main">Coaxial cable</span> Electrical cable type with concentric inner conductor, insulator, and conducting shield

Coaxial cable, or coax, is a type of electrical cable consisting of an inner conductor surrounded by a concentric conducting shield, with the two separated by a dielectric ; many coaxial cables also have a protective outer sheath or jacket. The term coaxial refers to the inner conductor and the outer shield sharing a geometric axis.

<span class="mw-page-title-main">BNC connector</span> RF connector for coax cable

The BNC connector is a miniature quick connect/disconnect radio frequency connector used for coaxial cable. It is designed to maintain the same characteristic impedance of the cable, with 50 ohm and 75 ohm types being made. It is usually applied for video and radio frequency connections up to about 2 GHz and up to 500 volts. The connector has a twist to lock design with two lugs in the female portion of the connector engaging a slot in the shell of the male portion. The type was introduced on military radio equipment in the 1940s and has since become widely applied in radio systems, and is a common type of video connector. Similar radio-frequency connectors differ in dimensions and attachment features, and may allow for higher voltages, higher frequencies, or three-wire connections.

<span class="mw-page-title-main">RF connector</span> Any electrical connector designed to work at radio frequencies in the multi-megahertz range

An RF connector is an electrical connector designed to work at radio frequencies in the multi-megahertz range. RF connectors are typically used with coaxial cables and are designed to maintain the shielding that the coaxial design offers. Better models also minimize the change in transmission line impedance at the connection in order to reduce signal reflection and power loss. As the frequency increases, transmission line effects become more important, with small impedance variations from connectors causing the signal to reflect rather than pass through. An RF connector must not allow external signals into the circuit through electromagnetic interference and capacitive pickup.

<span class="mw-page-title-main">APC-7 connector</span>

The APC-7 connector is a precision coaxial connector used on laboratory microwave test equipment for frequencies up to 18 GHz. APC-7 connectors are advantageous because they have a low reflection coefficient, make repeatable coaxial connections, and are genderless. The connectors are expensive, so they are seldom used outside the laboratory where their cost can be justified by their accuracy and convenience. Due to their high cost, their 18 GHz frequency limitation, and new laboratory practices, the connectors are now uncommon. Modern low-frequency microwave equipment often uses the less expensive 3.5 mm (26.5 GHz) connector. Higher-frequency equipment must use higher-performance connectors such as the 2.92 mm (40 GHz), 2.4 mm (50 GHz), 1.85 mm (67 GHz), or 1.0 mm (110 GHz) connectors.

<span class="mw-page-title-main">N connector</span> RF connecter for coaxial cables

The N connector is a threaded, weatherproof, medium-size RF connector used to join coaxial cables. It was one of the first connectors capable of carrying microwave-frequency signals, and was invented in the 1940s by Paul Neill of Bell Labs, after whom the connector is named.

<span class="mw-page-title-main">F connector</span> Coaxial RF connector used for television and cable Internet

The F connector is a coaxial RF connector commonly used for "over the air" terrestrial television, cable television and universally for satellite television and cable modems, usually with RG-6/U cable or with RG-59/U cable.

<span class="mw-page-title-main">SMA connector</span> Coaxial cable connector with semi-precision minimal connector interface developed in the 1960s

SMA connectors are semi-precision coaxial RF connectors developed in the 1960s as a minimal connector interface for coaxial cable with a screw-type coupling mechanism. The connector has a 50 Ω impedance. SMA was originally designed for use from DC (0 Hz) to 12 GHz, however this has been extended over time and variants are available to 18 GHz and 26.5 GHz. There are also mechanically compatible connectors such as the K-connector which operate up to 40 GHz. The SMA connector is most commonly used in microwave systems, hand-held radio and mobile telephone antennas and, more recently, with WiFi antenna systems and USB software-defined radio dongles. It is also commonly used in radio astronomy, particularly at higher frequencies (5 GHz+).

<span class="mw-page-title-main">SMC connector</span>

SMC connectors are coaxial RF connectors developed in the 1960s. The interface specifications for the SMC and many other connectors are referenced in MIL-STD-348. They use a #10-32 UNF threaded interface. They offer electrical performance from direct current (DC) to 4 GHz. Some extended performance versions are rated to 10 GHz. The normally free part of a SMC connector that has a socket for the centre contact are the female connectors. The normally fixed part SMC connectors that has a pin for the centre contact are the male connectors. This is the reverse of most RF connectors. SMC jack connectors have an external thread while SMC plug connectors have the mating hex nut. The contact dimensions are identical to the snap-fit SMB. Available in 50 ohm and 75 ohm characteristic impedance, they provide an interconnect means for small form factor coaxial cables and printed circuit boards where small footprint is important.

<span class="mw-page-title-main">Gender of connectors and fasteners</span> Male components insert into female components

In electrical and mechanical trades and manufacturing, each half of a pair of mating connectors or fasteners is conventionally assigned the designation male or female. The female connector is generally a receptacle that receives and holds the male connector. Alternative terminology such as plug and socket or jack are sometimes used, particularly for electrical connectors.

<span class="mw-page-title-main">Presta valve</span> Bicycle tube valve

The Presta valve is a type of tire valve commonly found on high pressure bicycle inner tubes and is commonly used on tubeless setups. It consists of an outer valve stem and an inner valve body. A lock nut to secure the stem at the wheel rim and a valve cap may also be present.

<span class="mw-page-title-main">Optical fiber connector</span> Device used to join fiber optic strands in communication systems

An optical fiber connector is a device used to link optical fibers, facilitating the efficient transmission of light signals. An optical fiber connector enables quicker connection and disconnection than splicing.

<span class="mw-page-title-main">UHF connector</span> Type of radio frequency connector

The UHF connector is a name for a threaded RF connector. The connector design was invented in the 1930s for use in the radio industry. It is a widely used standard connector for HF transmission lines on full-sized radio equipment, with BNC connectors predominating for smaller, hand-held equipment.

<span class="mw-page-title-main">Hose coupling</span> Connector on the end of a hose

A hose coupling is a connector on the end of a hose to connect it with another hose or with a tap or a hose appliance, such as an irrigation sprinkler. It is usually made of steel, brass, stainless steel, aluminium or plastic.

<span class="mw-page-title-main">MMCX connector</span>

Micro-miniature coaxial (MMCX) connectors are coaxial RF connectors similar to MCX but smaller. They conform to the European CECC 22000 specification. MMCX connectors are rated to 500 mating cycles. The connectors have a lock-snap mechanism allowing 360-degree rotation and usually have a 50 Ω impedance. They offer broadband capability from DC to 6 GHz.

<span class="mw-page-title-main">Coaxial power connector</span> Type of electrical power connector

A coaxial power connector is an electrical power connector used for attaching extra-low voltage devices such as consumer electronics to external electricity. Also known as barrel connectors, concentric barrel connectors or tip connectors, these small cylindrical connectors come in an enormous variety of sizes.

EIA RF Connectors are used to connect two items of high power radio frequency rigid or semi-rigid (flexline) coaxial transmission line. Typically these are only required in very high power transmitting installations where the feedline diameters may be several inches. The connectors are always female, requiring a male coupling element or bullet to make the connection. The EIA under the Electronic Components Industry Association, are responsible for a number of standard imperial connector sizes.

<span class="mw-page-title-main">U.S. Military connector specifications</span>

Electrical or fiber-optic connectors used by U.S. Department of Defense were originally developed in the 1930s for severe aeronautical and tactical service applications, and the Type "AN" (Army-Navy) series set the standard for modern military circular connectors. These connectors, and their evolutionary derivatives, are often called Military Standard, "MIL-STD", or (informally) "MIL-SPEC" or sometimes "MS" connectors. They are now used in aerospace, industrial, marine, and even automotive commercial applications.

<span class="mw-page-title-main">7/16 DIN connector</span>

The 7-16 DIN connector or 7/16 is a 50 Ω threaded RF connector used to join coaxial cables. It was designed to reduce passive intermodulation from multiple transmitters. It is among the most widely used high power RF connectors in cellular network antenna systems. Originally popular in Europe, it has gained widespread use in the US and elsewhere.

<span class="mw-page-title-main">4.3-10 connector</span>

The 4.3-10 connector is a 50 Ω multi-purpose RF connector used to connect coaxial cables with other cables or RF devices, such as transmitters or antennas.

References

  1. ↑ "A Radically New Coaxial Connector for the Laboratory. General Radio Experimenter, Volume XXIII No. 5, October 1948" (PDF). Retrieved 2015-12-21.
  2. ↑ Thiessen, Arthur E. (1965). "A History of the General Radio Company 1915–1965" (PDF). West Concord, MA: General Radio Company. p. 61. Retrieved July 4, 2009.
  3. ↑ "New and Improved Coaxial Connectors. General Radio Experimenter, Volume 35 No. 10, October 1961" (PDF). Retrieved 2015-12-21.
  4. ↑ "General Radi 900-Q874 | GR-900 to GR-874 Coaxial Adapter Connector".
This page is based on this Wikipedia article
Text is available under the CC BY-SA 4.0 license; additional terms may apply.
Images, videos and audio are available under their respective licenses.