DisplayPort

Last updated

DisplayPort
DisplayPort.svg
Type Digital audio/video connector
Production history
Designer VESA
Designed May 2006;17 years ago (2006-05)
Manufacturer Various
Produced 2008–present
Superseded DVI, VGA, SCART, RGB Component
Superseded by None
General specifications
Length Various
Hot pluggable Yes
External Yes
Audio signal Optional; 1–8 channels, 16 or 24-bit linear PCM; 32–192 kHz sampling rate; maximum bitrate 36,864 kbit/s (4,608 kB/s)
Video signal Optional, maximum resolution limited by available bandwidth
Pins 20 pins for external connectors on desktops, notebooks, graphics cards, monitors, etc. and 30/20 pins for internal connections between graphics engines and built-in flat panels.
Data
Data signal Yes
Bitrate 1.62, 2.7, 5.4, 8.1, or 20 Gbit/s data rate per lane; 1, 2, or 4 lanes; (effective total 5.184, 8.64, 17.28, 25.92, or 77.37 Gbit/s for 4-lane link); 2 or 720 Mbit/s (effectively 1 or 576 Mbit/s) for the auxiliary channel.
Protocol Micro-packet
Pinout
DisplayPort Connector.svg
External connector (source-side) on PCB
Pin 1 ML_Lane 0 (p) [lower-alpha 1] Lane 0 (+)
Pin 2 GND Ground
Pin 3 ML_Lane 0 (n) [lower-alpha 1] Lane 0 (−)
Pin 4 ML_Lane 1 (p) [lower-alpha 1] Lane 1 (+)
Pin 5 GND Ground
Pin 6 ML_Lane 1 (n) [lower-alpha 1] Lane 1 (−)
Pin 7 ML_Lane 2 (p) [lower-alpha 1] Lane 2 (+)
Pin 8 GND Ground
Pin 9 ML_Lane 2 (n) [lower-alpha 1] Lane 2 (−)
Pin 10 ML_Lane 3 (p) [lower-alpha 1] Lane 3 (+)
Pin 11 GND Ground
Pin 12 ML_Lane 3 (n) [lower-alpha 1] Lane 3 (−)
Pin 13 CONFIG1 Connected to ground [lower-alpha 2]
Pin 14 CONFIG2 Connected to ground [lower-alpha 2]
Pin 15 AUX CH (p) Auxiliary channel (+)
Pin 16 GND Ground
Pin 17 AUX CH (n) Auxiliary channel (−)
Pin 18 Hot plug Hot plug detect
Pin 19 Return Return for power
Pin 20 DP_PWR Power for connector (3.3 V 500 mA)
  1. 1 2 3 4 5 6 7 8 This is the pinout for source-side connector, the sink-side connector pinout will have lanes 0–3 reversed in order; i.e., lane 3 will be on pin 1(n) and 3(p) while lane 0 will be on pin 10(n) and 12(p).
  2. 1 2 Pins 13 and 14 may either be directly connected to ground or connected to ground through a pulldown device.
DisplayPort connector Displayport-cable.jpg
DisplayPort connector
A DisplayPort port (top right) near an Ethernet port and a USB port RJ-45 Ethernet socket on Lenovo T410 Laptop.jpg
A DisplayPort port (top right) near an Ethernet port and a USB port

DisplayPort (DP) is a proprietary [lower-alpha 1] digital display interface developed by a consortium of PC and chip manufacturers and standardized by the Video Electronics Standards Association (VESA). It is primarily used to connect a video source to a display device such as a computer monitor. It can also carry audio, USB, and other forms of data. [1]

Contents

DisplayPort was designed to replace VGA, FPD-Link, and Digital Visual Interface (DVI). It is backward compatible with other interfaces, such as DVI and High-Definition Multimedia Interface (HDMI), through the use of either active or passive adapters. [2]

It is the first display interface to rely on packetized data transmission, a form of digital communication found in technologies such as Ethernet, USB, and PCI Express. It permits the use of internal and external display connections. Unlike legacy standards that transmit a clock signal with each output, its protocol is based on small data packets known as micro packets, which can embed the clock signal in the data stream, allowing higher resolution using fewer pins. [3] The use of data packets also makes it extensible, meaning more features can be added over time without significant changes to the physical interface. [4]

DisplayPort is able to transmit audio and video simultaneously, although each can be transmitted without the other. The video signal path can range from six to sixteen bits per color channel, and the audio path can have up to eight channels of 24-bit, 192 kHz uncompressed PCM audio. [1] A bidirectional, half-duplex auxiliary channel carries device management and device control data for the Main Link, such as VESA EDID, MCCS, and DPMS standards. The interface is also capable of carrying bidirectional USB signals. [5]

The interface uses a differential signal that is not compatible with DVI or HDMI. However, dual-mode DisplayPort ports are designed to transmit a single-link DVI or HDMI protocol (TMDS) across the interface through the use of an external passive adapter, enabling compatibility mode and converting the signal from 3.3 to 5 volts. For analog VGA/YPbPr and dual-link DVI, a powered active adapter is required for compatibility and does not rely on dual mode. Active VGA adapters are powered directly by the DisplayPort connector, while active dual-link DVI adapters typically rely on an external power source such as USB.

Versions

1.0 to 1.1

The first version, 1.0, was approved by VESA on 3 May 2006. [6] Version 1.1 was ratified on 2 April 2007, [7] and version 1.1a on 11 January 2008. [8]

DisplayPort 1.0–1.1a allow a maximum bandwidth of 10.8 Gbit/s (8.64 Gbit/s data rate) over a standard 4-lane main link. DisplayPort cables up to 2 meters in length are required to support the full 10.8 Gbit/s bandwidth. [8] DisplayPort 1.1 allows devices to implement alternative link layers such as fiber optic, allowing a much longer reach between source and display without signal degradation, [9] although alternative implementations are not standardized. It also includes HDCP in addition to DisplayPort Content Protection (DPCP). The DisplayPort 1.1a standard can be downloaded for free from the VESA website. [10] [ failed verification ]

1.2

DisplayPort version 1.2 was introduced on 7 January 2010. [11] The most significant improvement of this version is the doubling of the data rate to 17.28 Gbit/s in High Bit Rate 2 (HBR2) mode, which allows increased resolutions, higher refresh rates, and greater color depth, such as 3840 × 2160 at 60 Hz 10 bpc RGB. Other improvements include multiple independent video streams (daisy-chain connection with multiple monitors) called Multi-Stream Transport (MST), facilities for stereoscopic 3D, increased AUX channel bandwidth (from 1 Mbit/s to 720 Mbit/s), more color spaces including xvYCC, scRGB, and Adobe RGB 1998, and Global Time Code (GTC) for sub 1 μs audio/video synchronisation. Also Apple Inc.'s Mini DisplayPort connector, which is much smaller and designed for laptop computers and other small devices, is compatible with the new standard. [1] [12] [13] [14]

1.2a

DisplayPort version 1.2a was released in January 2013 [15] and may optionally include VESA's Adaptive Sync. [16] AMD's FreeSync uses the DisplayPort Adaptive-Sync feature for operation. FreeSync was first demonstrated at CES 2014 on a Toshiba Satellite laptop by making use of the Panel-Self-Refresh (PSR) feature from the Embedded DisplayPort standard, [17] and after a proposal from AMD, VESA later adapted the Panel-Self-Refresh feature for use in standalone displays and added it as an optional feature of the main DisplayPort standard under the name "Adaptive-Sync" in version 1.2a. [18] As it is an optional feature, support for Adaptive-Sync is not required for a display to be DisplayPort 1.2a-compliant.

1.3

DisplayPort version 1.3 was approved on 15 September 2014. [19] This standard increases overall transmission bandwidth to 32.4 Gbit/s with the new HBR3 mode featuring 8.1 Gbit/s per lane (up from 5.4 Gbit/s with HBR2 in version 1.2), for a total data throughput of 25.92 Gbit/s after factoring in 8b/10b encoding overhead. This bandwidth is enough for a 4K UHD display (3840 × 2160) at 120 Hz with 24 bit/px RGB color, a 5K display (5120 × 2880) at 60 Hz with 30 bit/px RGB color, or an 8K UHD display (7680 × 4320) at 30 Hz with 24 bit/px RGB color. Using Multi-Stream Transport (MST), a DisplayPort port can drive two 4K UHD (3840 × 2160) displays at 60 Hz, or up to four WQXGA (2560 × 1600) displays at 60 Hz with 24 bit/px RGB color. The new standard includes mandatory Dual-mode for DVI and HDMI adapters, implementing the HDMI  2.0 standard and HDCP  2.2 content protection. [20] The Thunderbolt 3 connection standard was originally to include DisplayPort 1.3 capability, but the final release ended up with only version 1.2. The VESA's Adaptive Sync feature in DisplayPort version 1.3 remains an optional part of the specification. [21]

1.4

DisplayPort version 1.4 was published 1 March 2016. [22] No new transmission modes are defined, so HBR3 (32.4 Gbit/s) as introduced in version 1.3 still remains as the highest available mode. DisplayPort 1.4 adds support for Display Stream Compression 1.2 (DSC), Forward Error Correction, HDR10 metadata defined in CTA-861.3, including static and dynamic metadata and the Rec. 2020 color space, for HDMI interoperability, [23] and extends the maximum number of inline audio channels to 32. [24]

1.4a

DisplayPort version 1.4a was published in April 2018. [25] VESA made no official press release for this version. It updated DisplayPort's Display Stream Compression implementation from DSC 1.2 to 1.2a. [26]

2.0

On 26 June 2019, VESA formally released the DisplayPort 2.0 standard. VESA stated that version 2.0 is the first major update to the DisplayPort standard since March 2016, and provides up to a ≈3× improvement in data rate (from 25.92 to 77.37 Gbit/s) compared to the previous version of DisplayPort (1.4a), as well as new capabilities to address the future performance requirements of traditional displays. These include beyond 8K resolutions, higher refresh rates and high dynamic range (HDR) support at higher resolutions, improved support for multiple display configurations, as well as improved user experience with augmented/virtual reality (AR/VR) displays, including support for 4K-and-beyond VR resolutions.

According to a roadmap published by VESA in September 2016, a new version of DisplayPort was intended to be launched in "early 2017". It would have improved the link rate from 8.1 to 10.0 Gbit/s, a 23% increase. [27] [28] This would have increased the total bandwidth from 32.4 Gbit/s to 40.0 Gbit/s. However, no new version was released in 2017, likely delayed to make further improvements after the HDMI Forum announced in January 2017 that their next standard (HDMI 2.1) would offer up to 48 Gbit/s of bandwidth. According to a press release on 3 January 2018, "VESA is also currently engaged with its members in the development of the next DisplayPort standard generation, with plans to increase the data rate enabled by DisplayPort by two-fold and beyond. VESA plans to publish this update within the next 18 months." [29] At CES 2019, VESA announced that the new version would support 8K @ 60 Hz without compression and was expected to be released in the first half of 2019. [30]

DP 2.0 configuration examples

With the increased bandwidth enabled by DisplayPort 2.0, VESA offers a high degree of versatility and configurations for higher display resolutions and refresh rates. In addition to the above-mentioned 8K resolution at 60 Hz with HDR support, UHBR20 through USB-C as DisplayPort Alt Mode enables a variety of high-performance configurations:

  • Single display resolutions
    • One 16K (15360 × 8640) display @ 60 Hz with 10 bpc (30 bit/px, HDR) RGB/Y′CBCR 4:4:4 color (with DSC)
    • One 10K (10240 × 4320) display @ 60 Hz and 8 bpc (24 bit/px, SDR) RGB/Y′CBCR 4:4:4 color (uncompressed)
  • Dual display resolutions
    • Two 8K (7680 × 4320) displays @ 120 Hz and 10 bpc (30 bit/px, HDR) RGB/Y′CBCR 4:4:4 color (with DSC)
    • Two 4K (3840 × 2160) displays @ 144 Hz and 8 bpc (24 bit/px, SDR) RGB/Y′CBCR 4:4:4 color (uncompressed)
  • Triple display resolutions
    • Three 10K (10240 × 4320) displays @ 60 Hz and 10 bpc (30 bit/px, HDR) RGB/Y′CBCR 4:4:4 color (with DSC)
    • Three 4K (3840 × 2160) displays @ 90 Hz and 10 bpc (30 bit/px, HDR) RGB/Y′CBCR 4:4:4 color (uncompressed)

When using only two lanes on the USB-C connector via DP Alt Mode to allow for simultaneous SuperSpeed USB data and video, DP 2.0 can enable such configurations as: [31]

  • Three 4K (3840 × 2160) displays @ 144 Hz and 10 bpc (30 bit/px, HDR) RGB/Y′CBCR 4:4:4 color (with DSC)
  • Two 4K × 4K (4096 × 4096) displays (for AR/VR headsets) @ 120 Hz and 10 bpc (30 bit/px, HDR) RGB/Y′CBCR 4:4:4 color (with DSC)
  • Three QHD (2560 × 1440) @ 120 Hz and 8 bpc (24 bit/px, SDR) RGB/Y′CBCR 4:4:4 color (uncompressed)
  • One 8K (7680 × 4320) display @ 30 Hz and 10 bpc (30 bit/px, HDR) RGB/Y′CBCR 4:4:4 color (uncompressed)

2.1

VESA announced version 2.1 of the DisplayPort standard on 17 October 2022. [32] This version incorporates the new DP40 and DP80 cable certifications, which test DisplayPort cables for proper operation at the UHBR10 (40 Gbit/s) and UHBR20 (80 Gbit/s) speeds introduced in version 2.0. Additionally, it revises some of the electrical requirements for DisplayPort devices in order to improve integration with USB4. In VESA's words:

DisplayPort 2.1 has tightened its alignment with the USB Type-C specification as well as the USB4 PHY specification to facilitate a common PHY servicing both DisplayPort and USB4. In addition, DisplayPort 2.1 has added a new DisplayPort bandwidth management feature to enable DisplayPort tunnelling to coexist with other I/O data traffic more efficiently over the USB4 link.

2.1a

VESA announced version 2.1a of the DisplayPort standard on 8 January 2024. [33]

Specifications

Main specifications

 DisplayPort version
1.01.1a1.21.2a1.31.41.4a2.02.1
Release dateMay 2006 (1.0) [34]
Mar 2007 (1.1) [35]
Jan 2008 (1.1a) [8]
Jan 2010 (1.2) [11]
May 2012 (1.2a) [35]
Sep 2014 [19] Mar 2016 (1.4) [22]
Apr 2018 (1.4a) [25]
Jun 2019 (2.0) [31]
Oct 2022 (2.1) [32]
Main link
Transmission modes:
RBR (1.62 Gbit/s per lane)Yes [36] :§1.6.1YesYesYesYes
HBR (2.70 Gbit/s per lane)Yes [36] :§1.6.1YesYesYesYes
HBR2 (5.40 Gbit/s per lane)NoYes [37] :§2.1.1YesYesYes
HBR3 (8.10 Gbit/s per lane)NoNoYes [19] YesYes
UHBR 10 (10.0 Gbit/s per lane)NoNoNoNoYes
UHBR 13.5 (13.5 Gbit/s per lane)NoNoNoNoYes
UHBR 20 (20.0 Gbit/s per lane)NoNoNoNoYes
Number of lanes [8] :§1.7.1 44444
Maximum total bandwidth [lower-alpha 2] 10.80 Gbit/s21.60 Gbit/s32.40 Gbit/s32.40 Gbit/s80.00 Gbit/s
Maximum total data rate [lower-alpha 3] 8.64 Gbit/s
17.28 Gbit/s25.92 Gbit/s25.92 Gbit/s77.37 Gbit/s
Encoding scheme [lower-alpha 4] [8] :§1.7.1 8b/10b8b/10b8b/10b8b/10b128b/132b
Compression (optional)   DSC 1.2 (DP 1.4)
DSC 1.2a (DP 1.4a)
DSC 1.2a
Auxiliary channel
Maximum bandwidth [8] :Fig. 3-3 2 Mbit/s [37] :§3.4 720 Mbit/s2 Mbit/s2 Mbit/s2 Mbit/s
Maximum data rate [8] :§3.4 1 Mbit/s [37] :§3.4 576 Mbit/s1 Mbit/s1 Mbit/s1 Mbit/s
Encoding scheme [8] :§1.7.2 Manchester II [37] :§3.4 8b/10bManchester IIManchester IIManchester II
Color format support
RGBYes [36] :§1.6.1YesYesYesYes
Y′CBCR 4:4:4Yes [36] :§1.6.1YesYesYesYes
Y′CBCR 4:2:2Yes [36] :§1.6.1YesYesYesYes
Y′CBCR 4:2:0NoNoYesYesYes
Y-only (monochrome)NoYes [37] :§2.2.4.3YesYesYes
Color depth support
6 bpc (18 bit/px)Yes [36] :§1.6.1YesYesYesYes
8 bpc (24 bit/px)Yes [36] :§1.6.1YesYesYesYes
10 bpc (30 bit/px)Yes [36] :§1.6.1YesYesYesYes
12 bpc (36 bit/px)Yes [36] :§1.6.1YesYesYesYes
16 bpc (48 bit/px)Yes [36] :§1.6.1YesYesYesYes
Color space support
ITU-R BT.601Yes [8] :§2.2.4YesYesYesYes
ITU-R BT.709Yes [8] :§2.2.4YesYesYesYes
sRGBNo [lower-alpha 5] Yes [37] :§2.2.4.3YesYesYes
scRGBNoYes [37] :§2.2.4.3YesYesYes
xvYCCNoYes [37] :§2.2.4.3YesYesYes
Adobe RGB (1998)NoYes [37] :§2.2.4.3YesYesYes
DCI-P3NoYes [37] :§2.2.4.3YesYesYes
Simplified color profileNoYes [37] :§2.2.4.3YesYesYes
ITU-R BT.2020NoNoYes [38] :4YesYes
Audio specifications
Max. sample rate [8] :§1.2.5 192 kHz [37] :§2.2.5.3 768 kHz768 kHz [22] 1536 kHz ?
Max. sample size [8] :§1.2.5 24 bits24 bits24 bits24 bits ?
Maximum audio channels [8] :§1.2.5 88832 ?
 1.0–1.1a1.2–1.2a1.31.4–1.4a2.0–2.1
DisplayPort version
  1. Only the DisplayPort specification versions 1.0 and 1.1a do not require signing a non-disclosure agreement with VESA.
  2. Total bandwidth (the number of binary digits transmitted per second) is equal to the bandwidth per lane of the highest supported transmission mode multiplied by the number of lanes.
  3. While the total bandwidth represents the number of physical bits transmitted across the interface, not all of the bits represent video data. Some of the transmitted bits are used for encoding purposes, so the rate at which video data can be transmitted across the DisplayPort interface is only a portion of the total bandwidth.
  4. The 8b/10b encoding scheme uses 10 bits of bandwidth to send 8 bits of data, so only 80% of the bandwidth is available for data throughput. The extra 2 bits are used for DC balancing (ensuring a roughly equal number of 1s and 0s). They consume bandwidth, but do not represent any data.
  5. In DisplayPort 1.0–1.1a, RGB images are simply sent without any specific colorimetry information

The DisplayPort main link is used for transmission of video and audio. The main link consists of a number of unidirectional serial data channels which operate concurrently, called lanes. A standard DisplayPort connection has 4 lanes, though some applications of DisplayPort implement more, such as the Thunderbolt 3 interface which implements up to 8 lanes of DisplayPort. [39] :4

In a standard DisplayPort connection, each lane has a dedicated set of twisted-pair wires, and transmits data across it using differential signaling. This is a self-clocking system, so no dedicated clock signal channel is necessary. [8] :§1.7.1 Unlike DVI and HDMI, which vary their transmission speed to the exact rate required for the specific video format, DisplayPort only operates at a few specific speeds; any excess bits in the transmission are filled with "stuffing symbols". [8] :§2.2.1.4

In DisplayPort versions 1.01.4a, the data is encoded using ANSI 8b/10b encoding prior to transmission. With this scheme, only 8 out of every 10 transmitted bits represent data; the extra bits are used for DC balancing (ensuring a roughly equal number of 1s and 0s). As a result, the rate at which data can be transmitted is only 80% of the physical bitrate. The transmission speeds are also sometimes expressed in terms of the "Link Symbol Rate", which is the rate at which these 8b/10b-encoded symbols are transmitted (i.e. the rate at which groups of 10 bits are transmitted, 8 of which represent data). The following transmission modes are defined in version 1.01.4a:

  • RBR (Reduced Bit Rate): 1.62 Gbit/s bandwidth per lane (162 MHz link symbol rate)
  • HBR (High Bit Rate): 2.70 Gbit/s bandwidth per lane (270 MHz link symbol rate)
  • HBR2 (High Bit Rate 2): 5.40 Gbit/s bandwidth per lane (540 MHz link symbol rate), introduced in DP 1.2
  • HBR3 (High Bit Rate 3): 8.10 Gbit/s bandwidth per lane (810 MHz link symbol rate), introduced in DP 1.3

DisplayPort 2.0 uses 128b/132b encoding; each group of 132 transmitted bits represents 128 bits of data. This scheme has an efficiency of 96.96%. [40] In addition, a small amount of overhead is added for the link layer control packet and other miscellaneous operations, resulting in an overall efficiency of ≈96.7%. [41] :§3.5.2.18 The following transmission modes are added in DP 2.0:

  • UHBR 10 (Ultra High Bit Rate 10): 10.0 Gbit/s bandwidth per lane
  • UHBR 13.5 (Ultra High Bit Rate 13.5): 13.5 Gbit/s bandwidth per lane
  • UHBR 20 (Ultra High Bit Rate 20): 20.0 Gbit/s bandwidth per lane

The total bandwidth of the main link in a standard 4-lane connection is the aggregate of all lanes:

  • RBR: 4 × 1.62 Gbit/s = 6.48 Gbit/s bandwidth (data rate of 5.184 Gbit/s or 648 MB/s with 8b/10b encoding)
  • HBR: 4 × 2.70 Gbit/s = 10.80 Gbit/s bandwidth (data rate of 8.64 Gbit/s or 1.08 GB/s)
  • HBR2: 4 × 5.40 Gbit/s = 21.60 Gbit/s bandwidth (data rate of 17.28 Gbit/s or 2.16 GB/s)
  • HBR3: 4 × 8.10 Gbit/s = 32.40 Gbit/s bandwidth (data rate of 25.92 Gbit/s or 3.24 GB/s)
  • UHBR 10: 4 × 10.0 Gbit/s = 40.00 Gbit/s bandwidth (data rate of 38.69 Gbit/s or 4.84 GB/s with 128b/132b encoding and FEC)
  • UHBR 13.5: 4 × 13.5 Gbit/s = 54.00 Gbit/s bandwidth (data rate of 52.22 Gbit/s or 6.52 GB/s)
  • UHBR 20: 4 × 20.0 Gbit/s = 80.00 Gbit/s bandwidth (data rate of 77.37 Gbit/s or 9.69 GB/s)

The transmission mode used by the DisplayPort main link is negotiated by the source and sink device when a connection is made, through a process called Link Training. This process determines the maximum possible speed of the connection. If the quality of the DisplayPort cable is insufficient to reliably handle HBR2 speeds for example, the DisplayPort devices will detect this and switch down to a lower mode to maintain a stable connection. [8] :§2.1.1 The link can be re-negotiated at any time if a loss of synchronization is detected. [8] :§1.7.3

Audio data is transmitted across the main link during the video blanking intervals (short pauses between each line and frame of video data). [8] :§2.2.5.3

Auxiliary channel

The DisplayPort AUX channel is a half-duplex (bidirectional) data channel used for miscellaneous additional data beyond video and audio, such as EDID (I2C) or CEC commands. [8] :§2.4 This bidirectional data channel is required, since the video lane signals are unidirectional from source to display. AUX signals are transmitted across a dedicated set of twisted-pair wires. DisplayPort 1.0 specified Manchester encoding with a 2  MBd signal rate (1 Mbit/s data rate). [8] :§3.4 Version 1.2 of the DisplayPort standard introduced a second transmission mode called FAUX (Fast AUX), which operated at 720 MBd with 8b/10b encoding (576 Mbit/s data rate), [37] :§3.4 but it was deprecated in version 1.3.

Cables and connectors

Cables

Compatibility and feature support

All DisplayPort cables are compatible with all DisplayPort devices, regardless of the version of each device or the cable certification level. [42]

All features of DisplayPort will function across any DisplayPort cable. DisplayPort does not have multiple cable designs; all DP cables have the same basic layout and wiring, and will support any feature including audio, daisy-chaining, G-Sync/FreeSync, HDR, and DSC.

DisplayPort cables differ in their transmission speed support. DisplayPort specifies seven different transmission modes (RBR, HBR, HBR2, HBR3, UHBR 10, UHBR 13.5, and UHBR 20) which support progressively higher bandwidths. Not all DisplayPort cables are capable of all seven transmission modes. VESA offers certifications for various levels of bandwidth. These certifications are optional, and not all DisplayPort cables are certified by VESA.

Cables with limited transmission speed are still compatible with all DisplayPort devices, but may place limits on the maximum resolution or refresh rate available.

DisplayPort cables are not classified by "version". Although cables are commonly labeled with version numbers, with HBR2 cables advertised as "DisplayPort 1.2 cables" for example, this notation is not permitted by VESA. [42] The use of version numbers with cables can falsely imply that a DisplayPort 1.4 display requires a "DisplayPort 1.4 cable", or that features introduced in version 1.4 such as HDR or DSC will not function with older "DP 1.2 cables". DisplayPort cables are classified only by their bandwidth certification level (RBR, HBR, HBR2, HBR3, etc.), if they have been certified at all.

Cable bandwidth and certifications

Not all DisplayPort cables are capable of functioning at the highest levels of bandwidth. Cables may be submitted to VESA for an optional certification at various bandwidth levels. VESA offers five levels of cable certification: Standard, DP8K, DP40, DP54, and DP80. [41] :§4.1 These certify DisplayPort cables for proper operation at the following speeds:

DisplayPort cable certifications
Transmission modeTransmission
bit rate
Minimum required
cable certification
RBR (Reduced Bit Rate)6.48 Gbit/sStandard VESA-certified DisplayPort cable
HBR (High Bit Rate)10.80 Gbit/s
HBR2 (High Bit Rate 2)21.60 Gbit/s
HBR3 (High Bit Rate 3)32.40 Gbit/sDP8K DisplayPort cable
UHBR10 (Ultra High Bit Rate 10)40.00 Gbit/sDP40 cable
UHBR13.5 (Ultra High Bit Rate 13.5)54.00 Gbit/sDP54 cable
UHBR20 (Ultra High Bit Rate 20)80.00 Gbit/sDP80 cable

In April 2013, VESA published an article stating that the DisplayPort cable certification did not have distinct tiers for HBR and HBR2 bandwidth, and that any certified standard DisplayPort cable—including those certified under DisplayPort 1.1—would be able to handle the 21.6 Gbit/s bandwidth of HBR2 that was introduced with the DisplayPort 1.2 standard. [42] The DisplayPort 1.2 standard defines only a single specification for High Bit Rate cable assemblies, which is used for both HBR and HBR2 speeds, although the DP cable certification process is governed by the DisplayPort PHY Compliance Test Standard (CTS) and not the DisplayPort standard itself. [37] :§5.7.1, §4.1

The DP8K certification was announced by VESA in January 2018, and certifies cables for proper operation at HBR3 speeds (8.1 Gbit/s per lane, 32.4 Gbit/s total). [43]

In June 2019, with the release of version 2.0 of the DisplayPort Standard, VESA announced that the DP8K certification was also sufficient for the new UHBR10 transmission mode. No new certifications were announced for the UHBR13.5 and UHBR20 modes. VESA is encouraging displays to use tethered cables for these speeds, rather than releasing standalone cables onto the market. [40]

It should also be noted that the use of Display Stream Compression (DSC), introduced in DisplayPort 1.4, greatly reduces the bandwidth requirements for the cable. Formats which would normally be beyond the limits of DisplayPort 1.4, such as 4K (3840 × 2160) at 144 Hz 8 bpc RGB/Y′CBCR 4:4:4 (31.4 Gbit/s data rate when uncompressed), can only be implemented by using DSC. This would reduce the physical bandwidth requirements by 2–3×, placing it well within the capabilities of an HBR2-rated cable.

This exemplifies why DisplayPort cables are not classified by "version"; although DSC was introduced in version 1.4, this does not mean it needs a so-called "DP 1.4 cable" (an HBR3-rated cable) to function. HBR3 cables are only required for applications which exceed HBR2-level bandwidth, not simply any application involving DisplayPort 1.4. If DSC is used to reduce the bandwidth requirements to HBR2 levels, then an HBR2-rated cable will be sufficient.

In version 2.1, VESA introduced the DP40 and DP80 cable certification tiers, which validate cables for UHBR10 and UHBR20 speeds respectively. DisplayPort 2.1a introduced DP54 cable certification for UHBR13.5 speed.

Cable length

The DisplayPort standard does not specify any maximum length for cables, though the DisplayPort 1.2 standard does set a minimum requirement that all cables up to 2 meters in length must support HBR2 speeds (21.6 Gbit/s), and all cables of any length must support RBR speeds (6.48 Gbit/s). [37] :§5.7.1, §4.1 Cables longer than 2 meters may or may not support HBR/HBR2 speeds, and cables of any length may or may not support HBR3 speeds or above.

Connectors and pin configuration

DisplayPort output on a computer DisplayPort on a computer.jpg
DisplayPort output on a computer

DisplayPort cables and ports may have either a "full-size" connector or a "mini" connector. These connectors differ only in physical shape—the capabilities of DisplayPort are the same regardless of which connector is used. Using a Mini DisplayPort connector does not affect performance or feature support of the connection.

Full-size DisplayPort connector

The standard DisplayPort connector (now referred to as a "full-size" connector to distinguish it from the mini connector) [37] :§4.1.1 was the sole connector type introduced in DisplayPort 1.0. It is a 20-pin single-orientation connector with a friction lock and an optional mechanical latch. The standard DisplayPort receptacle has dimensions of 16.10 mm (width) × 4.76 mm (height) × 8.88 mm (depth). [8] :§4.2.1.7, p201

The standard DisplayPort connector pin allocation is as follows: [8] :§4.2.1

  • 12 pins for the main link – the main link consists of four shielded twisted pairs. Each pair requires 3 pins; one for each of the two wires, and a third for the shield. [8] :§4.1.2, p183 (pins 1–12)
  • 2 additional ground pins – (pins 13 and 14)
  • 3 pins for the auxiliary channel – the auxiliary channel uses another 3-pin shielded twisted pair (pins 15–17)
  • 1 pin for HPD – hot-plug detection (pin 18)
  • 2 pins for power – 3.3 V power and return line (pins 19 and 20)

Mini DisplayPort connector

Mini DisplayPort plug Mdp plug.jpg
Mini DisplayPort plug

The Mini DisplayPort connector was developed by Apple for use in their computer products. It was first announced in October 2008 for use in the new MacBooks and Cinema Display. In 2009, VESA adopted it as an official standard, and in 2010 the specification was merged into the main DisplayPort standard with the release of DisplayPort 1.2. Apple freely licenses the specification to VESA.

The Mini DisplayPort (mDP) connector is a 20-pin single-orientation connector with a friction lock. Unlike the full-size connector, it does not have an option for a mechanical latch. The mDP receptacle has dimensions of 7.50 mm (width) × 4.60 mm (height) × 4.99 mm (depth). [44] :§2.1.3.6, pp27–31 The mDP pin assignments are the same as the full-size DisplayPort connector. [44] :§2.1.3

DP_PWR (pin 20)

Pin 20 on the DisplayPort connector, called DP_PWR, provides 3.3 V (±10%) DC power at up to 500 mA (minimum power delivery of 1.5 W). [8] :§3.2 This power is available from all DisplayPort receptacles, on both source and display devices. DP_PWR is intended to provide power for adapters, amplified cables, and similar devices, so that a separate power cable is not necessary.

Standard DisplayPort cable connections do not use the DP_PWR pin. Connecting the DP_PWR pins of two devices directly together through a cable can create a short circuit which can potentially damage devices, since the DP_PWR pins on two devices are unlikely to have exactly the same voltage (especially with a ±10% tolerance). [45] For this reason, the DisplayPort 1.1 and later standards specify that passive DisplayPort-to-DisplayPort cables must leave pin 20 unconnected. [8] :§3.2.2

However, in 2013 VESA announced that after investigating reports of malfunctioning DisplayPort devices, it had discovered that a large number of non-certified vendors were manufacturing their DisplayPort cables with the DP_PWR pin connected:

Recently VESA has experienced quite a few complaints regarding troublesome DisplayPort operation that ended up being caused by improperly made DisplayPort cables. These "bad" DisplayPort cables are generally limited to non-DisplayPort certified cables, or off-brand cables. To further investigate this trend in the DisplayPort cable market, VESA purchased a number of non-certified, off-brand cables and found that an alarmingly high number of these were configured improperly and would likely not support all system configurations. None of these cables would have passed the DisplayPort certification test, moreover some of these cables could potentially damage a PC, laptop, or monitor.

The stipulation that the DP_PWR wire be omitted from standard DisplayPort cables was not present in the DisplayPort 1.0 standard. However, DisplayPort products (and cables) did not begin to appear on the market until 2008, long after version 1.0 had been replaced by version 1.1. The DisplayPort 1.0 standard was never implemented in commercial products. [46]

Resolution and refresh frequency limits

The tables below describe the refresh frequencies that can be achieved with each transmission mode. In general, maximum refresh frequency is determined by the transmission mode (RBR, HBR, HBR2, HBR3, UHBR10, UHBR13.5, or UHBR20). These transmission modes were introduced to the DisplayPort standard as follows:

However, transmission mode support is not necessarily dictated by a device's claimed "DisplayPort version number". For example, older versions of the DisplayPort Marketing Guidelines allowed a device to be labeled as "DisplayPort 1.2" if it supported the MST feature, even if it didn't support the HBR2 transmission mode. [47] :9 Newer versions of the guidelines have removed this clause, and currently (as of the June 2018 revision) there are no guidelines on the usage of DisplayPort version numbers in products. [48] DisplayPort "version numbers" are therefore not a reliable indication of what transmission speeds a device can support.

In addition, individual devices may have their own arbitrary limitations beyond transmission speed. For example, NVIDIA Kepler GK104 GPUs (such as the GeForce GTX 680 and 770) support "DisplayPort 1.2" with the HBR2 transmission mode, but are limited to 540 Mpx/s, only 34 of the maximum possible with HBR2. [49] Consequently, certain devices may have limitations that differ from those listed in the following tables.

To support a particular format, the source and display devices must both support the required transmission mode, and the DisplayPort cable must also be capable of handling the required bandwidth of that transmission mode. (See: Cables and connectors)

Refresh frequency limits for common resolutions

The maximum limits for the RBR and HBR modes are calculated using standard data rate calculations. [50] For UHBR modes, the limits are based on the data efficiency calculations provided by the DisplayPort standard. [51] :§3.5.2.18 All calculations assume uncompressed RGB video with CVT-RB v2 timing. Maximum limits may differ if compression (i.e. DSC) or Y′CBCR 4:2:2 or 4:2:0 chroma subsampling are used.

Display manufacturers may also use non-standard blanking intervals rather than CVT-RB v2 to achieve even higher frequencies when bandwidth is a constraint. The refresh frequencies in the below table do not represent the absolute maximum limit of each interface, but rather an estimate based on a modern standardized timing formula. The minimum blanking intervals (and therefore the exact maximum frequency that can be achieved) will depend on the display and how many secondary data packets it requires, and therefore will differ from model to model.

Video formatTransmission mode / Maximum data rate
Short-
hand
ResolutionColor
depth
(bpc)
RBRHBRHBR2HBR3UHBR10UHBR13.5UHBR20
5.184 Gbit/s8.64 Gbit/s17.28 Gbit/s25.92 Gbit/s38.68 Gbit/s52.22 Gbit/s77.37 Gbit/s
Maximum refresh frequency with CVT-RB v2 timing uncompressed (Hz)
1080p1920 × 1080895154288406555688884
1077125237337468587770
1440p2560 × 144085590174251354452609
104473141205293378516
UWQHD3440 × 144084168133193277358491
103355107157227296412
4K3840 × 216084181120174229323
10336597142187267
5K5120 × 288084769102136195
10375682110159
8K7680 × 4320831476392
10375074
  Below 30 Hz
  030–60 Hz
  060–120 Hz
  120–240 Hz
  Above 240 Hz

    Refresh frequency limits for standard video

    Color depth of 8 bpc (24 bit/px or 16.7 million colors) is assumed for all formats in these tables. This is the standard color depth used on most computer displays. Note that some operating systems refer to this as "32-bit" color depth—this is the same as 24-bit color depth. The 8 extra bits are for alpha channel information, which is only present in software. At the transmission stage, this information has already been incorporated into the primary color channels, so the actual video data transmitted across the cable only contains 24 bits per pixel.

    Limits for uncompressed RGB / Y′CBCR 4:4:4 video only
    Video formatTransmission mode / maximum data rate [lower-alpha 1]
    ShorthandResolutionRefresh
    rate (Hz)
    Data rate
    required [lower-alpha 2]
    RBRHBRHBR2HBR3UHBR10UHBR13.5UHBR20
    5.184 Gbit/s8.64 Gbit/s17.28 Gbit/s25.92 Gbit/s38.69 Gbit/s52.22 Gbit/s77.37 Gbit/s
    1080p1920 × 1080603.20 Gbit/sYesYesYesYesYesYesYes
    854.59 Gbit/sYesYesYesYesYesYesYes
    1206.59 Gbit/sNoYesYesYesYesYesYes
    1448.00 Gbit/sNoYesYesYesYesYesYes
    24014.00 Gbit/sNoNoYesYesYesYesYes
    1440p2560 × 1440302.78 Gbit/sYesYesYesYesYesYesYes
    605.63 Gbit/sNoYesYesYesYesYesYes
    858.07 Gbit/sNoYesYesYesYesYesYes
    12011.59 Gbit/sNoNoYesYesYesYesYes
    14414.08 Gbit/sNoNoYesYesYesYesYes
    16516.30 Gbit/sNoNoYesYesYesYesYes
    24024.62 Gbit/sNoNoNoYesYesYesYes
    4K3840 × 2160244.93 Gbit/sYesYesYesYesYesYesYes
    306.18 Gbit/sNoYesYesYesYesYesYes
    6012.54 Gbit/sNoNoYesYesYesYesYes
    7515.79 Gbit/sNoNoYesYesYesYesYes
    12025.82 Gbit/sNoNoNoYesYesYesYes
    14431.35 Gbit/sNoNoNoNoYesYesYes
    24054.84 Gbit/sNoNoNoNoNoYes [lower-alpha 3] Yes
    5K5120 × 2880248.73 Gbit/sNoYes [lower-alpha 3] YesYesYesYesYes
    3010.94 Gbit/sNoNoYesYesYesYesYes
    6022.18 Gbit/sNoNoNoYesYesYesYes
    12045.66 Gbit/sNoNoNoNoNoYesYes
    14455.44 Gbit/sNoNoNoNoNoNoYes
    18070.54 Gbit/sNoNoNoNoNoNoYes
    24096.98 Gbit/sNoNoNoNoNoNoNo
    8K7680 × 43202419.53 Gbit/sNoNoNoYesYesYesYes
    3024.48 Gbit/sNoNoNoYesYesYesYes
    6049.65 Gbit/sNoNoNoNoNoYesYes
    8571.17 Gbit/sNoNoNoNoNoNoYes
    120102.20 Gbit/sNoNoNoNoNoNoNo
    RBRHBRHBR2HBR3UHBR 10UHBR 13.5UHBR 20
    Transmission mode
    1. Only a portion of DisplayPort's bandwidth is used for carrying video data. The RBR, HBR, HBR2, and HBR3 transmission modes use 8b/10b encoding, which means that 80% of the bits transmitted across the link represent data, and the other 20% are used for encoding purposes. The maximum bit rates of these modes (6.48, 10.8, 21.6, and 32.4 Gbit/s) therefore transport video data at rates of 5.184, 8.64, 17.28, and 25.92 Gbit/s respectively. DisplayPort UHBR modes use 128b/132b encoding, and therefore the maximum bit rates of UHBR10, 13.5, and 20 (40, 54, and 80 Gbit/s) transport data at rates of 38.69, 52.22, and 77.37 Gbit/s.
    2. These data rates are for uncompressed 8 bpc (24 bit/px) color depth with RGB or YCBCR 4:4:4 color format and CVT-R2 timing. Uncompressed data rate for RGB video in bits per second is calculated as bits per pixel × pixels per frame × frames per second. Pixels per frame includes blanking intervals as defined by CVT-R2.
    3. 1 2 Although this format slightly exceeds the maximum data rate of this transmission mode with CVT-R2 timing, it is close enough to be achieved with non-standard timings
    Limits including compression and chroma subsampling
    Video formatTransmission mode / maximum data rate [lower-alpha 1]
    ShorthandResolutionRefresh
    rate (Hz)
    Data rate
    required [lower-alpha 2]
    RBRHBRHBR2HBR3UHBR10UHBR13.5UHBR20
    5.184 Gbit/s8.64 Gbit/s17.28 Gbit/s25.92 Gbit/s38.69 Gbit/s52.22 Gbit/s77.37 Gbit/s
    1080p1920 × 1080603.20 Gbit/sYesYesYesYesYesYesYes
    854.59 Gbit/sYesYesYesYesYesYesYes
    1206.59 Gbit/sDSC [lower-alpha 3] or 4:2:2 [lower-alpha 4] YesYesYesYesYesYes
    1448.00 Gbit/sDSC or 4:2:0YesYesYesYesYesYes
    24014.00 Gbit/sDSCDSC or 4:2:0YesYesYesYesYes
    1440p2560 × 1440302.78 Gbit/sYesYesYesYesYesYesYes
    605.63 Gbit/sDSC or 4:2:2YesYesYesYesYesYes
    858.07 Gbit/sDSC or 4:2:0YesYesYesYesYesYes
    12011.59 Gbit/sDSCDSC or 4:2:2YesYesYesYesYes
    14414.08 Gbit/sDSCDSC or 4:2:0YesYesYesYesYes
    16516.30 Gbit/sDSC + 4:2:2 [lower-alpha 5] DSC or 4:2:0YesYesYesYesYes
    24024.62 Gbit/sDSC + 4:2:0DSCDSC or 4:2:2YesYesYesYes
    4K3840 × 2160244.93 Gbit/sYesYesYesYesYesYesYes
    306.18 Gbit/sDSC or 4:2:2YesYesYesYesYesYes
    6012.54 Gbit/sDSCDSC or 4:2:2YesYesYesYesYes
    7515.79 Gbit/sDSCDSC or 4:2:0YesYesYesYesYes
    12025.82 Gbit/sDSC + 4:2:0DSCDSC or 4:2:2YesYesYesYes
    14431.35 Gbit/sDSC + 4:2:0DSC + 4:2:2DSC or 4:2:0DSC or 4:2:2YesYesYes
    24054.84 Gbit/sNoNoDSC + 4:2:2DSCDSC or 4:2:2Yes [lower-alpha 6] Yes
    5K5120 × 2880248.73 Gbit/sDSC or 4:2:0Yes [lower-alpha 6] YesYesYesYesYes
    3010.94 Gbit/sDSCDSC or 4:2:2YesYesYesYesYes
    6022.18 Gbit/sDSC + 4:2:2DSCDSC or 4:2:2YesYesYesYes
    12045.66 Gbit/sNoDSC + 4:2:0DSCDSC or 4:2:0DSC or 4:2:2YesYes
    14455.44 Gbit/sNoNoDSC + 4:2:2DSCDSC or 4:2:2DSC or 4:2:2Yes
    18070.54 Gbit/sNoNoDSC + 4:2:2DSCDSC or 4:2:0DSC or 4:2:2Yes
    24096.98 Gbit/sNoNoDSC + 4:2:0DSC + 4:2:2DSC or 4:2:0DSC or 4:2:0DSC or 4:2:2
    8K7680 × 43202419.53 Gbit/sDSC + 4:2:2DSCDSC or 4:2:2YesYesYesYes
    3024.48 Gbit/sDSC + 4:2:0DSCDSC or 4:2:2YesYesYesYes
    6049.65 Gbit/sNoDSC + 4:2:0DSCDSC or 4:2:0DSC or 4:2:2YesYes
    8571.17 Gbit/sNoNoDSC + 4:2:2DSCDSC or 4:2:0DSC or 4:2:2Yes
    120102.20 Gbit/sNoNoDSC + 4:2:0DSC + 4:2:2DSCDSC or 4:2:0DSC or 4:2:2
    144124.09 Gbit/sNoNoNoDSC + 4:2:0DSC + 4:2:2DSCDSC or 4:2:0
    240217.10 Gbit/sNoNoNoNoDSC + 4:2:0DSC + 4:2:2DSC
    RBRHBRHBR2HBR3UHBR10UHBR13.5UHBR20
    Transmission mode
    1. Only a portion of DisplayPort's bandwidth is used for carrying video data. The RBR, HBR, HBR2, and HBR3 transmission modes use 8b/10b encoding, which means that 80% of the bits transmitted across the link represent data, and the other 20% are used for encoding purposes. The maximum bit rates of these modes (6.48, 10.8, 21.6, and 32.4 Gbit/s) therefore transport video data at rates of 5.184, 8.64, 17.28, and 25.92 Gbit/s respectively. DisplayPort UHBR modes use 128b/132b encoding, and therefore the maximum bit rates of UHBR10, 13.5, and 20 (40, 54, and 80 Gbit/s) transport data at rates of 38.69, 52.22, and 77.37 Gbit/s.
    2. These data rates are for uncompressed 8 bpc (24 bit/px) color depth with RGB or YCBCR 4:4:4 color format and CVT-R2 timing. Uncompressed data rate for RGB video in bits per second is calculated as bits per pixel × pixels per frame × frames per second. Pixels per frame includes blanking intervals as defined by CVT-R2.
    3. This format can only be achieved with full RGB color if DSC (display stream compression) is used.
    4. This format can only be achieved uncompressed if the YCBCR format with either 4:2:2 or 4:2:0 chroma subsampling (as noted) is used
    5. This format can only be achieved if DSC is used together with either YCbCr 4:2:2 or 4:2:0 chroma subsampling (as noted)
    6. 1 2 Although this format slightly exceeds the maximum data rate of this transmission mode with CVT-R2 timing, it is close enough to be achieved with non-standard timings

    Refresh frequency limits for HDR video

    Color depth of 10 bpc (30 bit/px or 1.07 billion colors) is assumed for all formats in these tables. This color depth is a requirement for various common HDR standards, such as HDR10. It requires 25% more bandwidth than standard 8 bpc video.

    HDR extensions were defined in version 1.4 of the DisplayPort standard. Some displays support these HDR extensions, but may only implement HBR2 transmission mode if the extra bandwidth of HBR3 is unnecessary (for example, on 4K 60 Hz HDR displays). Since there is no definition of what constitutes a "DisplayPort 1.4" device, some manufacturers may choose to label these as "DP 1.2" devices despite their support for DP 1.4 HDR extensions. [52] As a result, DisplayPort "version numbers" should not be used as an indicator of HDR support.

    Limits for uncompressed RGB / Y′CBCR 4:4:4 video only
    Video FormatTransmission Mode / Maximum Data Rate [lower-alpha 1]
    ShorthandResolutionRefresh
    Rate (Hz)
    Data Rate
    Required [lower-alpha 2]
    RBRHBRHBR2HBR3UHBR10UHBR13.5UHBR20
    5.184 Gbit/s8.64 Gbit/s17.28 Gbit/s25.92 Gbit/s38.69 Gbit/s52.22 Gbit/s77.37 Gbit/s
    1080p1920 × 1080604.00 Gbit/sYesYesYesYesYesYesYes
    1006.80 Gbit/sNoYesYesYesYesYesYes
    1208.24 Gbit/sNoYesYesYesYesYesYes
    14410.00 Gbit/sNoNoYesYesYesYesYes
    24017.50 Gbit/sNoNoYes [lower-alpha 3] YesYesYesYes
    1440p2560 × 1440303.47 Gbit/sYesYesYesYesYesYesYes
    607.04 Gbit/sNoYesYesYesYesYesYes
    758.86 Gbit/sNoYes [lower-alpha 3] YesYesYesYesYes
    12014.49 Gbit/sNoNoYesYesYesYesYes
    14417.60 Gbit/sNoNoYes [lower-alpha 3] YesYesYesYes
    20025.12 Gbit/sNoNoNoYesYesYesYes
    24030.77 Gbit/sNoNoNoNoYesYesYes
    4K3840 × 2160307.73 Gbit/sNoYesYesYesYesYesYes
    6015.68 Gbit/sNoNoYesYesYesYesYes
    9826.07 Gbit/sNoNoNoYes [lower-alpha 3] YesYesYes
    12032.27 Gbit/sNoNoNoNoYesYesYes
    14439.19 Gbit/sNoNoNoNoYes [lower-alpha 3] YesYes
    18049.85 Gbit/sNoNoNoNoNoYesYes
    24068.56 Gbit/sNoNoNoNoNoNoYes
    5K5120 × 28803013.67 Gbit/sNoNoYesYesYesYesYes
    5022.99 Gbit/sNoNoNoYesYesYesYes
    6027.72 Gbit/sNoNoNoNoYesYesYes
    8539.75 Gbit/sNoNoNoNoYes [lower-alpha 3] YesYes
    10047.10 Gbit/sNoNoNoNoNoYesYes
    12057.08 Gbit/sNoNoNoNoNoNoYes
    14469.30 Gbit/sNoNoNoNoNoNoYes
    8K7680 × 43202424.41 Gbit/sNoNoNoYesYesYesYes
    3030.60 Gbit/sNoNoNoNoYesYesYes
    5051.47 Gbit/sNoNoNoNoNoYesYes
    6062.06 Gbit/sNoNoNoNoNoNoYes
    7578.13 Gbit/sNoNoNoNoNoNoYes [lower-alpha 3]
    RBRHBRHBR2HBR3UHBR10UHBR13.5UHBR20
    Transmission Mode
    1. Only a portion of DisplayPort's bandwidth is used for carrying video data. The RBR, HBR, HBR2, and HBR3 transmission modes use 8b/10b encoding, which means that 80% of the bits transmitted across the link represent data, and the other 20% are used for encoding purposes. The maximum bit rates of these modes (6.48, 10.8, 21.6, and 32.4 Gbit/s) therefore transport video data at rates of 5.184, 8.64, 17.28, and 25.92 Gbit/s respectively. DisplayPort UHBR modes use 128b/132b encoding, and therefore the maximum bit rates of UHBR10, 13.5, and 20 (40, 54, and 80 Gbit/s) transport data at rates of 38.69, 52.22, and 77.37 Gbit/s.
    2. These data rates are for uncompressed 10 bpc (30 bit/px) color depth with RGB or YCBCR 4:4:4 color format and CVT-R2 timing. Uncompressed data rate for RGB video in bits per second is calculated as bits per pixel × pixels per frame × frames per second. Pixels per frame includes blanking intervals as defined by CVT-R2.
    3. 1 2 3 4 5 6 7 Although this format slightly exceeds the maximum data rate of this transmission mode with CVT-R2 timing, it is close enough to be achieved with non-standard timings
    Limits including compression and chroma subsampling
    Video FormatTransmission Mode / Maximum Data Rate [lower-alpha 1]
    ShorthandResolutionRefresh
    Rate (Hz)
    Data Rate
    Required [lower-alpha 2]
    RBRHBRHBR2HBR3UHBR10UHBR13.5UHBR20
    5.184 Gbit/s8.64 Gbit/s17.28 Gbit/s25.92 Gbit/s38.69 Gbit/s52.22 Gbit/s77.37 Gbit/s
    1080p1920 × 1080604.00 Gbit/sYesYesYesYesYesYesYes
    1006.80 Gbit/sDSC [lower-alpha 3] or 4:2:2 [lower-alpha 4] YesYesYesYesYesYes
    1208.24 Gbit/sDSC or 4:2:0YesYesYesYesYesYes
    14410.00 Gbit/sDSC or 4:2:0DSC or 4:2:2YesYesYesYesYes
    24017.50 Gbit/sDSC + 4:2:2 [lower-alpha 5] DSC or 4:2:0Yes [lower-alpha 6] YesYesYesYes
    1440p2560 × 1440303.47 Gbit/sYesYesYesYesYesYesYes
    607.04 Gbit/sDSC or 4:2:2YesYesYesYesYesYes
    758.86 Gbit/sDSC or 4:2:0Yes [lower-alpha 6] YesYesYesYesYes
    12014.49 Gbit/sDSCDSC or 4:2:0YesYesYesYesYes
    14417.60 Gbit/sDSC + 4:2:2DSC or 4:2:0Yes [lower-alpha 6] YesYesYesYes
    20025.12 Gbit/sDSC + 4:2:0DSCDSC or 4:2:2YesYesYesYes
    24030.77 Gbit/sDSC + 4:2:0DSC + 4:2:2DSC or 4:2:0DSC or 4:2:2YesYesYes
    4K3840 × 2160307.73 Gbit/sDSC or 4:2:2YesYesYesYesYesYes
    6015.68 Gbit/sDSCDSC or 4:2:0YesYesYesYesYes
    7519.74 Gbit/sDSC + 4:2:2DSCDSC or 4:2:2YesYesYesYes
    9826.07 Gbit/sDSC + 4:2:0DSCDSC or 4:2:2Yes [lower-alpha 6] YesYesYes
    12032.27 Gbit/sNoDSC + 4:2:2DSC or 4:2:0DSC or 4:2:2YesYesYes
    14439.19 Gbit/sNoDSC + 4:2:2DSCDSC or 4:2:2YesYesYes
    18049.85 Gbit/sNoDSC + 4:2:0DSCDSC or 4:2:0DSC or 4:2:2YesYes
    24068.56 Gbit/sNoNoDSC + 4:2:2DSCDSC or 4:2:0DSC or 4:2:2Yes
    5K5120 × 28803013.67 Gbit/sDSCDSC or 4:2:0YesYesYesYesYes
    5022.99 Gbit/sDSC + 4:2:2DSCDSC or 4:2:2YesYesYesYes
    6027.72 Gbit/sDSC + 4:2:0DSC + 4:2:2DSC or 4:2:0DSC or 4:2:2YesYesYes
    10047.10 Gbit/sNoDSC + 4:2:0DSCDSC or 4:2:0DSC or 4:2:2YesYes
    12057.08 Gbit/sNoNoDSC + 4:2:2DSCDSC or 4:2:2DSC or 4:2:2Yes
    14469.30 Gbit/sNoNoDSC + 4:2:2DSCDSC or 4:2:0DSC or 4:2:2Yes
    240121.23 Gbit/sNoNoNoDSC + 4:2:0DSCDSCDSC or 4:2:0
    8K7680 × 43202424.41 Gbit/sDSC + 4:2:0DSCDSC or 4:2:2YesYesYesYes
    3030.60 Gbit/sDSC + 4:2:0DSC + 4:2:2DSC or 4:2:0DSC or 4:2:2YesYesYes
    5051.47 Gbit/sNoDSC + 4:2:0DSCDSC or 4:2:0DSC or 4:2:2YesYes
    6062.06 Gbit/sNoNoDSC + 4:2:2DSCDSC or 4:2:0DSC or 4:2:2Yes
    7578.13 Gbit/sNoNoDSC + 4:2:2DSCDSC or 4:2:0DSC or 4:2:2Yes [lower-alpha 6]
    120127.75 Gbit/sNoNoNoDSC + 4:2:0DSC + 4:2:2DSCDSC or 4:2:0
    144155.11 Gbit/sNoNoNoDSC + 4:2:0DSC + 4:2:2DSCDSC or 4:2:0
    240271.37 Gbit/sNoNoNoNoNoDSC + 4:2:0DSC + 4:2:2
    RBRHBRHBR2HBR3UHBR10UHBR13.5UHBR20
    Transmission Mode
    1. Only a portion of DisplayPort's bandwidth is used for carrying video data. The RBR, HBR, HBR2, and HBR3 transmission modes use 8b/10b encoding, which means that 80% of the bits transmitted across the link represent data, and the other 20% are used for encoding purposes. The maximum bit rates of these modes (6.48, 10.8, 21.6, and 32.4 Gbit/s) therefore transport video data at rates of 5.184, 8.64, 17.28, and 25.92 Gbit/s respectively. DisplayPort UHBR modes use 128b/132b encoding, and therefore the maximum bit rates of UHBR10, 13.5, and 20 (40, 54, and 80 Gbit/s) transport data at rates of 38.69, 52.22, and 77.37 Gbit/s.
    2. These data rates are for uncompressed 10 bpc (30 bit/px) color depth with RGB or YCBCR 4:4:4 color format and CVT-R2 timing. Uncompressed data rate for RGB video in bits per second is calculated as bits per pixel × pixels per frame × frames per second. Pixels per frame includes blanking intervals as defined by CVT-R2.
    3. This format can only be achieved with full RGB color if DSC (display stream compression) is used.
    4. This format can only be achieved uncompressed if the YCBCR format with either 4:2:2 or 4:2:0 chroma subsampling (as noted) is used
    5. This format can only be achieved if DSC is used together with either YCbCr 4:2:2 or 4:2:0 chroma subsampling (as noted)
    6. 1 2 3 4 5 Although this format slightly exceeds the maximum data rate of this transmission mode with CVT-R2 timing, it is close enough to be achieved with non-standard timings

    Features

     DisplayPort version
    1.01.1–1.1a1.2–1.2a1.31.4–1.4a2.0
    Hot-pluggableYesYesYesYesYesYes
    Inline audioYesYesYesYesYesYes
    DisplayPort content
    protection (DPCP)
    DPCP 1.0 [36] :§1.2.6DPCP 1.0DPCP 1.0DPCP 1.0DPCP 1.0DPCP 1.0
    High-bandwidth digital
    content protection (HDCP)
    NoHDCP 1.3 [8] :§1.2.6HDCP 1.3 [37] :§1.2.6HDCP 2.2 [19] HDCP 2.2HDCP 2.2
    Dual-mode (DP++)NoYesYesYesYesYes
    Maximum DP++ bandwidth
    (TMDS Clock)
    4.95 Gbit/s
    (165 MHz)
    9.00 Gbit/s
    (300 MHz)
    18.00 Gbit/s
    (600 MHz)
    18.00 Gbit/s
    (600 MHz)
    18.00 Gbit/s
    (600 MHz)
    Stereoscopic 3D videoNoYesYesYesYesYes
    Multi-stream transport (MST)NoNoYesYesYesYes
    High-dynamic-range video (HDR)NoNoNoNoYesYes
    Display stream compression (DSC)NoNoNoNoDSC 1.2 (DP 1.4)
    DSC 1.2a (DP 1.4a)
    DSC 1.2a
    Panel replayNoNoNoNoNoYes [40]

      DisplayPort Dual-Mode (DP++)

      Dual-mode DisplayPort logo DisplayPort plus plus.svg
      Dual-mode DisplayPort logo
      Dual-mode pin mapping
      DisplayPort pinsDVI/HDMI mode
      Main link lane 0TMDS channel 2
      Main link lane 1TMDS channel 1
      Main link lane 2TMDS channel 0
      Main link lane 3TMDS clock
      AUX CH+DDC clock
      AUX CH−DDC data
      DP_PWRDP_PWR
      Hot-plug detectHot-plug detect
      Config 1Cable adapter detect
      Config 2 CEC (HDMI only)

      DisplayPort Dual-Mode (DP++), also called Dual-Mode DisplayPort, is a standard which allows DisplayPort sources to use simple passive adapters to connect to HDMI or DVI displays. Dual-mode is an optional feature, so not all DisplayPort sources necessarily support DVI/HDMI passive adapters, though in practice nearly all devices do. Officially, the "DP++" logo should be used to indicate a DP port that supports dual-mode, but most modern devices do not use the logo. [53]

      Devices which implement dual-mode will detect that a DVI or HDMI adapter is attached, and send DVI/HDMI TMDS signals instead of DisplayPort signals. The original DisplayPort Dual-Mode standard (version 1.0), used in DisplayPort 1.1 devices, only supported TMDS clock speeds of up to 165 MHz (4.95 Gbit/s bandwidth). This is equivalent to HDMI 1.2, and is sufficient for up to 1920 × 1200 at 60 Hz.

      In 2013, VESA released the Dual-Mode 1.1 standard, which added support for up to a 300 MHz TMDS clock (9.00 Gbit/s bandwidth), and is used in newer DisplayPort 1.2 devices. This is slightly less than the 340 MHz maximum of HDMI 1.4, and is sufficient for up to 1920 × 1080 at 120 Hz, 2560 × 1440 at 60 Hz, or 3840 × 2160 at 30 Hz. Older adapters, which were only capable of the 165 MHz speed, were retroactively termed "Type 1" adapters, with the new 300 MHz adapters being called "Type 2". [54]

      Dual-mode limitations

      A DisplayPort to DVI adapter after removing its enclosure. The chip on the board converts the voltage levels generated by the dual-mode DisplayPort device to be compatible with a DVI monitor. Despite the chip, this is often categorized as a passive adapter. DP to DVI converter unmounted.jpg
      A DisplayPort to DVI adapter after removing its enclosure. The chip on the board converts the voltage levels generated by the dual-mode DisplayPort device to be compatible with a DVI monitor. Despite the chip, this is often categorized as a passive adapter.
      • Limited adapter speed Although the pinout and digital signal values transmitted by the DP port are identical to a native DVI/HDMI TMDS source, the transmission lines on a DisplayPort source are AC-coupled (a series capacitor isolates the line from passing DC voltages) while DVI and HDMI TMDS are DC-coupled. As a result, dual-mode adapters must contain a level-shifting circuit which couples the signal lines to a DC source. [53] :§5.5 The presence of this circuit places a limit on how quickly the adapter can operate, and therefore newer adapters are required for each higher speed added to the standard.
      • Unidirectional Although the dual-mode standard specifies a method for DisplayPort sources to output DVI/HDMI signals using simple passive adapters, there is no counterpart standard to give DisplayPort displays the ability to receive DVI/HDMI input signals through passive adapters. As a result, DisplayPort displays can only receive native DisplayPort signals; any DVI or HDMI input signals must be converted to the DisplayPort format with an active conversion device. DVI and HDMI sources cannot be connected to DisplayPort displays using passive adapters.
      • Single-link DVI only Since DisplayPort dual-mode operates by using the pins of the DisplayPort connector to send DVI/HDMI signals, the 20-pin DisplayPort connector can only produce a single-link DVI signal (which uses 19 pins). A dual-link DVI signal uses 25 pins, and is therefore impossible to transmit natively from a DisplayPort connector through a passive adapter. Dual-link DVI signals can only be produced by converting from native DisplayPort output signals with an active conversion device.
      • Unavailable on USB-C The DisplayPort Alternate Mode specification for sending DisplayPort signals over a USB-C cable does not include support for the dual-mode protocol. As a result, DP-to-DVI and DP-to-HDMI passive adapters do not function when chained from a USB-C to DP adapter.

      Multi-Stream Transport (MST)

      Multi-Stream Transport is a feature first introduced in the DisplayPort 1.2 standard. It allows multiple independent displays to be driven from a single DP port on the source devices by multiplexing several video streams into a single stream and sending it to a branch device, which demultiplexes the signal into the original streams. Branch devices are commonly found in the form of an MST hub, which plugs into a single DP input port and provides multiple outputs, but it can also be implemented on a display internally to provide a DP output port for daisy-chaining, effectively embedding a 2-port MST hub inside the display. [37] :Fig. 2-59 [55] Theoretically, up to 63 displays can be supported, [37] :20 but the combined data rate requirements of all the displays cannot exceed the limits of a single DP port (17.28 Gbit/s for a DP 1.2 port, or 25.92 Gbit/s for a DP 1.3/1.4 port). In addition, the maximum number of links between the source and any device (i.e. the maximum length of a daisy-chain) is 7, [37] :§2.5.2 and the maximum number of physical output ports on each branch device (such as a hub) is 7. [37] :§2.5.1 With the release of MST, standard single-display operation has been retroactively named "SST" mode (Single-Stream Transport).

      Daisy-chaining is a feature that must be specifically supported by each intermediary display; not all DisplayPort 1.2 devices support it. Daisy-chaining requires a dedicated DisplayPort output port on the display. Standard DisplayPort input ports found on most displays cannot be used as a daisy-chain output. Only the last display in the daisy-chain does not need to support the feature specifically or have a DP output port. DisplayPort 1.1 displays can also be connected to MST hubs, and can be part of a DisplayPort daisy-chain if it is the last display in the chain. [37] :§2.5.1

      The host system's software also needs to support MST for hubs or daisy-chains to work. While Microsoft Windows environments have full support for it, Apple operating systems currently do not support MST hubs or DisplayPort daisy-chaining as of macOS 10.15 ("Catalina"). [56] [57] DisplayPort-to-DVI and DisplayPort-to-HDMI adapters/cables may or may not function from an MST output port; support for this depends on the specific device.[ citation needed ]

      MST is supported by USB Type-C DisplayPort Alternate Mode, so standard DisplayPort daisy-chains and MST hubs do function from Type-C sources with a simple Type-C to DisplayPort adapter. [58]

      High dynamic range (HDR)

      Support for HDR video was introduced in DisplayPort 1.4. It implements the CTA 861.3 standard for transport of static HDR metadata in EDID. [22]

      Content protection

      DisplayPort 1.0 includes optional DPCP (DisplayPort Content Protection) from Philips, which uses 128-bit AES encryption. It also features full authentication and session key establishment. Each encryption session is independent, and it has an independent revocation system. This portion of the standard is licensed separately. It also adds the ability to verify the proximity of the receiver and transmitter, a technique intended to ensure users are not bypassing the content protection system to send data out to distant, unauthorized users. [8] :§6

      DisplayPort 1.1 added optional implementation of industry-standard 56-bit HDCP (High-bandwidth Digital Content Protection) revision 1.3, which requires separate licensing from the Digital Content Protection LLC. [8] :§1.2.6

      DisplayPort 1.3 added support for HDCP 2.2, which is also used by HDMI 2.0. [19]

      Cost

      VESA, the creators of the DisplayPort standard, state that the standard is royalty-free to implement. However, in March 2015, MPEG LA issued a press release stating that a royalty rate of $0.20 per unit applies to DisplayPort products manufactured or sold in countries that are covered by one or more of the patents in the MPEG LA license pool, which includes patents from Hitachi Maxell, Philips, Lattice Semiconductor, Rambus, and Sony. [59] [60] In response, VESA updated their DisplayPort FAQ page with the following statement: [61]

      MPEG LA is making claims that DisplayPort implementation requires a license and a royalty payment. It is important to note that these are only CLAIMS. Whether these CLAIMS are relevant will likely be decided in a US court.

      As of August 2019, VESA's official FAQ no longer contains a statement mentioning the MPEG LA royalty fees.

      While VESA does not charge any per-device royalty fees, VESA requires membership for access to said standards. [62] The minimum cost is presently $5,000 (or $10,000 depending on Annual Corporate Sales Revenue) annually. [63]

      In December 2010, several computer vendors and display makers including Intel, AMD, Dell, Lenovo, Samsung and LG announced they would begin phasing out FPD-Link, VGA, and DVI-I over the next few years, replacing them with DisplayPort and HDMI. [64] [65] [66]

      DisplayPort has several advantages over VGA, DVI, and FPD-Link. [67]

      Comparison with HDMI

      Although DisplayPort has much of the same functionality as HDMI, it is a complementary connection used in different scenarios. [71] [72] A dual-mode DisplayPort port can emit an HDMI signal via a passive adapter.

      Market share

      Figures from IDC show that 5.1% of commercial desktops and 2.1% of commercial notebooks released in 2009 featured DisplayPort. [64] The main factor behind this was the phase-out of VGA, and that both Intel and AMD planned to stop building products with FPD-Link by 2013. Nearly 70% of LCD monitors sold in August 2014 in the US, UK, Germany, Japan, and China were equipped with HDMI/DisplayPort technology, up 7.5% on the year, according to Digitimes Research. [81] IHS Markit, an analytics firm, forecast that DisplayPort would surpass HDMI in 2019. [82] [ needs update ]

      Companion standards

      Mini DisplayPort

      Mini DisplayPort (mDP) is a standard announced by Apple in the fourth quarter of 2008. Shortly after announcing Mini DisplayPort, Apple announced that it would license the connector technology with no fee. The following year, in early 2009, VESA announced that Mini DisplayPort would be included in the upcoming DisplayPort 1.2 specification. On 24 February 2011, Apple and Intel announced Thunderbolt, a successor to Mini DisplayPort which adds support for PCI Express data connections while maintaining backwards compatibility with Mini DisplayPort based peripherals. [83]

      Micro DisplayPort

      Micro DisplayPort would have targeted systems that need ultra-compact connectors, such as phones, tablets and ultra-portable notebook computers. This standard would have been physically smaller than the currently available Mini DisplayPort connectors. The standard was expected to be released by Q2 2014. [84]

      DDM

      Direct Drive Monitor (DDM) 1.0 standard was approved in December 2008. It allows for controller-less monitors where the display panel is directly driven by the DisplayPort signal, although the available resolutions and color depth are limited to two-lane operation.

      Display Stream Compression

      Display Stream Compression (DSC) is a VESA-developed video compression algorithm designed to enable increased display resolutions and frame rates over existing physical interfaces, and make devices smaller and lighter, with longer battery life. [85]

      eDP

      Embedded DisplayPort (eDP) is a display panel interface standard for portable and embedded devices. It defines the signaling interface between graphics cards and integrated displays. The various revisions of eDP are based on existing DisplayPort standards. However, version numbers between the two standards are not interchangeable. For instance, eDP version 1.4 is based on DisplayPort 1.2, while eDP version 1.4a is based on DisplayPort 1.3. Embedded DisplayPort has displaced LVDS as the predominant panel interface in modern laptops and modern smartphones.

      eDP 1.0 was adopted in December 2008. [86] It included advanced power-saving features such as seamless refresh rate switching. Version 1.1 was approved in October 2009 followed by version 1.1a in November 2009. Version 1.2 was approved in May 2010 and includes DisplayPort 1.2 HBR2 data rates, 120 Hz sequential color monitors, and a new display panel control protocol that works through the AUX channel. [12] Version 1.3 was published in February 2011; it includes a new optional Panel Self-Refresh (PSR) feature developed to save system power and further extend battery life in portable PC systems. [87] PSR mode allows the GPU to enter a power saving state in between frame updates by including framebuffer memory in the display panel controller. [12] Version 1.4 was released in February 2013; it reduces power consumption through partial-frame updates in PSR mode, regional backlight control, lower interface voltages, and additional link rates; the auxiliary channel supports multi-touch panel data to accommodate different form factors. [88] Version 1.4a was published in February 2015; the underlying DisplayPort version was updated to 1.3 in order to support HBR3 data rates, Display Stream Compression 1.1, Segmented Panel Displays, and partial updates for Panel Self-Refresh. [89] Version 1.4b was published in October 2015; its protocol refinements and clarifications are intended to enable adoption of eDP 1.4b in devices by mid-2016. [90] Version 1.5 was published in October 2021; adds new features and protocols, including enhanced support for Adaptive-Sync, that provide additional power savings and improved gaming and media playback performance. [91]

      iDP

      Internal DisplayPort (iDP) is a standard that defines an internal link between a digital TV system on a chip controller and the display panel's timing controller. Version 1.0 was approved in April 2010. It aims to replace currently used internal FPD-Link lanes with a DisplayPort connection. [92] iDP features a unique physical interface and protocols, which are not directly compatible with DisplayPort and are not applicable to external connection, however they enable very high resolution and refresh rates while providing simplicity and extensibility. [12] iDP features a non-variable 2.7 GHz clock and is nominally rated at 3.24 Gbit/s per lane, with up to sixteen lanes in a bank, resulting in a six-fold decrease in wiring requirements over FPD-Link for a 1080p24 signal; other data rates are also possible. iDP was built with simplicity in mind so doesn't have an AUX channel, content protection, or multiple streams; it does however have frame sequential and line interleaved stereo 3D. [12]

      PDMI

      Portable Digital Media Interface (PDMI) is an interconnection between docking stations/display devices and portable media players, which includes 2-lane DisplayPort v1.1a connection. It has been ratified in February 2010 as ANSI/CEA-2017-A.

      wDP

      Wireless DisplayPort (wDP) enables the bandwidth and feature set of DisplayPort 1.2 for cable-free applications operating in the 60 GHz radio band. It was announced in November 2010 by WiGig Alliance and VESA as a cooperative effort. [93]

      SlimPort

      A SlimPort-to-HDMI adapter, made by Analogix A SlimPort-to-HDMI adapter, made by Analogix.jpg
      A SlimPort-to-HDMI adapter, made by Analogix

      SlimPort, a brand of Analogix products, [94] complies with Mobility DisplayPort, also known as MyDP, which is an industry standard for a mobile audio/video Interface, providing connectivity from mobile devices to external displays and HDTVs. SlimPort implements the transmission of video up to 4K-UltraHD and up to eight channels of audio over the micro-USB connector to an external converter accessory or display device. SlimPort products support seamless connectivity to DisplayPort, HDMI and VGA displays. [95] The MyDP standard was released in June 2012, [96] and the first product to use SlimPort was Google's Nexus 4 smartphone. [97] Some LG smartphones in LG G series also adopted SlimPort.

      SlimPort is an alternative to Mobile High-Definition Link (MHL). [98] [99]

      DisplayID

      DisplayID is designed to replace the E-EDID standard. DisplayID features variable-length structures which encompass all existing EDID extensions as well as new extensions for 3D displays and embedded displays.

      The latest version 1.3 (announced on 23 September 2013) adds enhanced support for tiled display topologies; it allows better identification of multiple video streams, and reports bezel size and locations. [100] As of December 2013, many current 4K displays use a tiled topology, but lack a standard way to report to the video source which tile is left and which is right. These early 4K displays, for manufacturing reasons, typically use two 1920×2160 panels laminated together and are currently generally treated as multiple-monitor setups. [101] DisplayID 1.3 also allows 8K display discovery, and has applications in stereo 3D, where multiple video streams are used.

      DockPort

      DockPort, formerly known as Lightning Bolt, is an extension to DisplayPort to include USB 3.0 data as well as power for charging portable devices from attached external displays. Originally developed by AMD and Texas Instruments, it has been announced as a VESA specification in 2014. [102]

      USB-C

      On 22 September 2014, VESA published the DisplayPort Alternate Mode on USB Type-C Connector Standard, a specification on how to send DisplayPort signals over the newly released USB-C connector. One, two or all four of the differential pairs that USB uses for the SuperSpeed bus can be configured dynamically to be used for DisplayPort lanes. In the first two cases, the connector still can carry a full SuperSpeed signal; in the latter case, at least a non-SuperSpeed signal is available. The DisplayPort AUX channel is also supported over the two sideband signals over the same connection; furthermore, USB Power Delivery according to the newly expanded USB-PD 2.0 specification is possible at the same time. This makes the Type-C connector a strict superset of the use cases envisioned for DockPort, SlimPort, and Mini and Micro DisplayPort. [103]

      VirtualLink is a proposal that allows the power, video, and data required to drive virtual reality headsets to be delivered over a single USB-C cable.

      Products

      A Dual-mode DisplayPort connector Lenovo x220 dp crop.jpg
      A Dual-mode DisplayPort connector

      Since DisplayPort's introduction in 2006, it has gained popularity within the computer industry and is featured on many graphics cards, displays, and notebook computers. Dell was the first company to introduce a consumer product with a DisplayPort connector, the Dell UltraSharp 3008WFP, which was released in January 2008. [104] Soon after, AMD and Nvidia released products to support the technology. AMD included support in the Radeon HD 3000 series of graphics cards, and Nvidia first introduced support in the GeForce 9 series starting with the GeForce 9600 GT. [105] [106]

      A Mini DisplayPort connector Mini DisplayPort on Apple MacBook.jpg
      A Mini DisplayPort connector

      Later in 2008, Apple introduced several products featuring a Mini DisplayPort. [107] The new connector proprietary at the time eventually became part of the DisplayPort standard, however Apple reserves the right to void the license should the licensee "commence an action for patent infringement against Apple". [108] In 2009, AMD followed suit with their Radeon HD 5000 series of graphics cards, which featured the Mini DisplayPort on the Eyefinity versions in the series. [109]

      Nvidia launched a graphics card with 8 Mini DisplayPort outputs on 4 November 2015, called the NVS 810, which was intended for digital signage. [110] [111]

      Nvidia revealed the GeForce GTX 1080, the world's first graphics card with DisplayPort 1.4 support on 6 May 2016. [112] AMD followed with the Radeon RX 480 to support DisplayPort 1.3/1.4 on 29 June 2016. [113] The Radeon RX 400 series will support DisplayPort 1.3 HBR and HDR10, dropping the DVI connector(s) in the reference board design.

      In February 2017, VESA and Qualcomm announced that DisplayPort Alt Mode video transport will be integrated into the Snapdragon 835 mobile chipset, which powers smartphones, VR/AR head-mounted displays, IP cameras, tablets and mobile PCs. [114]

      Support for DisplayPort Alternate Mode over USB-C

      A Samsung Galaxy S8 plugged into a DeX docking station Samsung DeX dock with S8, plugged into monitor.jpg
      A Samsung Galaxy S8 plugged into a DeX docking station

      Currently, DisplayPort is the most widely implemented alternate mode, and is used to provide video output on devices that do not have standard-size DisplayPort or HDMI ports, such as smartphones, tablets, and laptops. A USB-C multiport adapter converts the device's native video stream to DisplayPort/HDMI/VGA, allowing it to be displayed on an external display, such as a television set or computer monitor.

      Examples of devices that support DisplayPort Alternate Mode over USB-C include: MacBook, Chromebook Pixel, Surface Book 2, Samsung Galaxy Tab S4, iPad Pro (3rd generation), iPhone 15/15 Pro, HTC 10/U Ultra/U11/U12+, Huawei Mate 10/20/30, LG V20/V30/V40*/V50, OnePlus 7 and newer, ROG Phone, Samsung Galaxy S8 and newer, Nintendo Switch, Sony Xperia 1/5 etc. [115] [116]

      Participating companies

      The following companies have participated in preparing the drafts of DisplayPort, eDP, iDP, DDM or DSC standards:

      The following companies have additionally announced their intention to implement DisplayPort, eDP or iDP:

      See also

      Notes

      1. Dual-link DVI is limited in resolution and speed by the quality and therefore the bandwidth of the DVI cable, the quality of the transmitter, and the quality of the receiver; can only drive one monitor at a time; and cannot send audio data. HDMI 1.3 and 1.4 are limited to effectively 8.16 Gbit/s or 340 MHz (though actual devices are limited to 225–300 MHz[ citation needed ]), and can only drive one monitor at a time. VGA connectors have no defined maximum resolution or speed, but their analog nature limits their bandwidth, though can provide long cabling only limited by appropriate shielding.

      Related Research Articles

      <span class="mw-page-title-main">USB</span> Standard for computer data connections

      Universal Serial Bus (USB) is an industry standard that allows data exchange and delivery of power between many various types of electronics. It specifies its architecture, in particular its physical interface, and communication protocols for data transfer and power delivery to and from hosts, such as personal computers, to and from peripheral devices, e.g. displays, keyboards, and mass storage devices, and to and from intermediate hubs, which multiply the number of a host's ports.

      <span class="mw-page-title-main">Digital Visual Interface</span> Standard for transmitting digital video to a display

      Digital Visual Interface (DVI) is a video display interface developed by the Digital Display Working Group (DDWG). The digital interface is used to connect a video source, such as a video display controller, to a display device, such as a computer monitor. It was developed with the intention of creating an industry standard for the transfer of uncompressed digital video content.

      <span class="mw-page-title-main">Video Graphics Array</span> Computer display standard and resolution

      Video Graphics Array (VGA) is a video display controller and accompanying de facto graphics standard, first introduced with the IBM PS/2 line of computers in 1987, which became ubiquitous in the IBM PC compatible industry within three years. The term can now refer to the computer display standard, the 15-pin D-subminiature VGA connector, or the 640 × 480 resolution characteristic of the VGA hardware.

      <span class="mw-page-title-main">Graphics card</span> Expansion card which generates a feed of output images to a display device

      A graphics card is a computer expansion card that generates a feed of graphics output to a display device such as a monitor. Graphics cards are sometimes called discrete or dedicated graphics cards to emphasize their distinction to an integrated graphics processor on the motherboard or the central processing unit (CPU). A graphics processing unit (GPU) that performs the necessary computations is the main component in a graphics card, but the acronym "GPU" is sometimes also used to erroneously refer to the graphics card as a whole.

      The Display Data Channel, or DDC, is a collection of protocols for digital communication between a computer display and a graphics adapter that enable the display to communicate its supported display modes to the adapter and that enable the computer host to adjust monitor parameters, such as brightness and contrast.

      <span class="mw-page-title-main">Serial digital interface</span> Family of digital video interfaces

      Serial digital interface (SDI) is a family of digital video interfaces first standardized by SMPTE in 1989. For example, ITU-R BT.656 and SMPTE 259M define digital video interfaces used for broadcast-grade video. A related standard, known as high-definition serial digital interface (HD-SDI), is standardized in SMPTE 292M; this provides a nominal data rate of 1.485 Gbit/s.

      <span class="mw-page-title-main">HDMI</span> Proprietary interface for transmitting digital audio and video data

      High-Definition Multimedia Interface (HDMI) is a proprietary audio/video interface for transmitting uncompressed video data and compressed or uncompressed digital audio data from an HDMI-compliant source device, such as a display controller, to a compatible computer monitor, video projector, digital television, or digital audio device. HDMI is a digital replacement for analog video standards.

      <span class="mw-page-title-main">VGA connector</span> 15-pin video connector

      The Video Graphics Array (VGA) connector is a standard connector used for computer video output. Originating with the 1987 IBM PS/2 and its VGA graphics system, the 15-pin connector went on to become ubiquitous on PCs, as well as many monitors, projectors and high-definition television sets.

      <span class="mw-page-title-main">Unified Display Interface</span>

      Unified Display Interface (UDI) was a digital video interface specification released in 2006 which was based on Digital Visual Interface (DVI). It was intended to be a lower cost implementation while providing compatibility with existing High-Definition Multimedia Interface (HDMI) and DVI displays. Unlike HDMI, which is aimed at high-definition multimedia consumer electronics devices such as television monitors and DVD players, UDI was specifically targeted towards computer monitor and video card manufacturers and did not support the transfer of audio data. A contemporary rival standard, DisplayPort, gained significant industry support starting in 2007 and the UDI specification was abandoned shortly thereafter without having released any products.

      WirelessHD, also known as UltraGig, is a proprietary standard owned by Silicon Image for wireless transmission of high-definition video content for consumer electronics products. The consortium currently has over 40 adopters; key members behind the specification include Broadcom, Intel, LG, Panasonic, NEC, Samsung, SiBEAM, Sony, Philips and Toshiba. The founders intend the technology to be used for Consumer Electronic devices, PCs, and portable devices.

      Mobile High-Definition Link (MHL) is an industry standard for a mobile audio/video interface that allows the connection of smartphones, tablets, and other portable consumer electronics devices to high-definition televisions (HDTVs), audio receivers, and projectors. The standard was designed to share existing mobile device connectors, such as Micro-USB, and avoid the need to add video connectors on devices with limited space for them.

      Wireless Home Digital Interface (WHDI) is a consumer electronic specification for a wireless HDTV connectivity throughout the home.

      Uncompressed video is digital video that either has never been compressed or was generated by decompressing previously compressed digital video. It is commonly used by video cameras, video monitors, video recording devices, and in video processors that perform functions such as image resizing, image rotation, deinterlacing, and text and graphics overlay. It is conveyed over various types of baseband digital video interfaces, such as HDMI, DVI, DisplayPort and SDI. Standards also exist for the carriage of uncompressed video over computer networks.

      <span class="mw-page-title-main">Mini DisplayPort</span> Miniaturized version of the DisplayPort connector

      The Mini DisplayPort is a miniaturized version of the DisplayPort audio-visual digital interface.

      Thunderbolt is the brand name of a hardware interface for the connection of external peripherals to a computer. It was developed by Intel in collaboration with Apple. It was initially marketed under the name Light Peak, and first sold as part of an end-user product on 24 February 2011.

      <span class="mw-page-title-main">HDBaseT</span> Point-to-point media connection over category cable

      HDBaseT is a consumer electronic (CE) and commercial connectivity standard for transmission of uncompressed ultra-high-definition video, digital audio, DC power, Ethernet, USB 2.0, and other control communication over a single category cable up to 100 m (328 ft) in length, terminated using the same 8P8C modular connectors as used in Ethernet networks. HDBaseT technology is promoted and advanced by the HDBaseT Alliance.

      V-by-One HS is an electrical digital signaling standard that can run at faster speeds over inexpensive twisted-pair copper cables than Low-voltage differential signaling, or LVDS. It was originally developed by THine Electronics, Inc. in 2007 for high-definition televisions but since 2010 V-by-One HS has been widely adopted in various markets such as document processing, automotive infotainment systems, industrial cameras and machine vision, robotics and amusement equipments.

      <span class="mw-page-title-main">USB-C</span> 24-pin USB connector system

      USB-C, or USB Type-C, is a 24-pin connector that supersedes previous USB connectors and can carry audio, video and other data, e.g., to drive multiple displays or to store a backup to an external drive. It can also provide and receive power, such as powering a laptop or a mobile phone. It is applied not only by USB technology, but also by other protocols, including Thunderbolt, PCIe, HDMI, DisplayPort, and others. It is extensible to support future standards.

      Display Stream Compression (DSC) is a VESA-developed video compression algorithm designed to enable increased display resolutions and frame rates over existing physical interfaces, and make devices smaller and lighter, with longer battery life. It is a low-latency algorithm based on delta PCM coding and YCGCO-R color space.

      <span class="mw-page-title-main">USB4</span> Technical standard in computing

      Universal Serial Bus 4, marketed as USB4 and sometimes referred to as USB 4.0, is a new technical specification of the Universal Serial Bus data connection standard, released on 29 August 2019 by the USB Implementers Forum.

      References

      1. 1 2 3 "DisplayPort Technical Overview" (PDF). VESA.org. 10 January 2011. Retrieved 23 January 2012.
      2. "DisplayPort... the End of an Era, but Beginning of a New Age". Hope Industrial Systems. 27 April 2011. Retrieved 9 March 2012.
      3. "AMD's Eyefinity Technology Explained". Tom's Hardware. 28 February 2010. Retrieved 23 January 2012.
      4. "An Inside Look at DisplayPort v1.2". ExtremeTech. 4 February 2011. Retrieved 28 July 2011.
      5. "The Case For DisplayPort, Continued, And Bezels". Tom's Hardware. 15 April 2010. Retrieved 28 July 2011.
      6. "New DisplayPort(TM) Interface Standard for PCs, Monitors, TV Displays and Projectors Released by the Video Electronics Standards Association". Video Electronics Standards Association (VESA). 3 May 2006. Archived from the original on 14 February 2009.
      7. Hodgin, Rick (30 July 2007). "DisplayPort: The new video interconnect standard". geek.com. Archived from the original on 16 October 2012. Retrieved 21 July 2011.
      8. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 "VESA DisplayPort Standard, Version 1, Revision 1a" (PDF). Video Electronics Standards Association (VESA). 11 January 2008. Archived from the original (PDF) on 8 April 2016.
      9. "Video Electronics Standards Association (VESA) Endorses Alternative to Copper Cables". Luxtera Inc. 17 April 2007. Archived from the original on 18 February 2010. Retrieved 19 January 2010.
      10. "Free Standards". Video Electronics Standards Association (VESA). Retrieved 2 May 2018.
      11. 1 2 "VESA Introduces DisplayPort v1.2, the Most Comprehensive and Innovative Display Interface Available". www.vesa.org. Video Electronics Standards Association (VESA). 7 January 2010. Archived from the original on 2 May 2018. Retrieved 2 May 2018.
      12. 1 2 3 4 5 "DisplayPort Developer Conference Presentations Posted". Vesa. 6 December 2010.{{cite journal}}: Cite journal requires |journal= (help)
      13. "WinHEC 2008 GRA-583: Display Technologies". Microsoft. 6 November 2008. Archived from the original on 27 December 2008.
      14. Tony Smith, "DisplayPort revision to get mini connector, stereo 3D" Archived 14 October 2009 at the Wayback Machine , The Register, 13 January 2009
      15. Joseph D. Cornwall (15 January 2014). "DisplayPort in A/V Applications in the Next Five Years". connectorsupplier.com. Retrieved 10 May 2018.
      16. "VESA Adds 'Adaptive-Sync' to Popular DisplayPort Video Standard". vesa.org. 12 May 2014. Retrieved 27 January 2016.
      17. Anand Lal Shimpi. "AMD Demonstrates "FreeSync", Free G-Sync Alternative, at CES 2014". anandtech.com. Retrieved 27 January 2016.
      18. "AMD 'FreeSync': proposition pour le DP 1.2a". hardware.fr. Retrieved 27 January 2016.
      19. 1 2 3 4 5 "VESA Releases DisplayPort 1.3 Standard". Video Electronics Standards Association (VESA). 15 September 2014. Archived from the original on 12 August 2017. Retrieved 27 January 2016.
      20. "VESA Releases DisplayPort 1.3 Standard: 50% More Bandwidth, New Features". www.anandtech.com. Retrieved 7 January 2016.
      21. "VESA Releases DisplayPort 1.3 Standard: 50% More Bandwidth, New Features". 16 September 2014. Retrieved 15 September 2016. DisplayPort Active-Sync remains an optional part of the specification, so Adaptive-Sync availability will continue to be on a monitor-by-monitor basis as a premium feature.
      22. 1 2 3 4 "VESA Publishes DisplayPort Standard Version 1.4". Video Electronics Standards Association (VESA). 1 March 2016. Archived from the original on 3 January 2018. Retrieved 2 March 2016.
      23. "DisplayPort 1.4 vs HDMI 2.1". Planar.
      24. "VESA Updates Display Stream Compression Standard to Support New Applications and Richer Display Content". PRNewswire. 27 January 2016. Retrieved 29 January 2016.
      25. 1 2 "FAQ  DisplayPort". Archived from the original on 24 December 2018.
      26. "DSC Display Stream Compression". Archived from the original on 10 July 2019.
      27. "imgur.com". Imgur.
      28. "VESA DisplayPort Alternate Mode on USB-C  Technical Overview" (PDF). USB Implementers Forum. 28 September 2016.
      29. "VESA Strengthens 8K Video Resolution Ecosystem with Market-ready DP8K Certified DisplayPort Cables". VESA  Interface Standards for The Display Industry. 3 January 2018.
      30. Sag, Anshel (12 February 2019). "Display Technologies Ruled At CES 2019". Forbes.com . Retrieved 12 April 2019.
      31. 1 2 "VESA Publishes DisplayPort 2.0 Video Standard Enabling Support for Beyond-8K Resolutions, Higher Refresh Rates For 4K/HDR and Virtual Reality Applications". 26 June 2019. Retrieved 26 June 2019.
      32. 1 2 "VESA Releases DisplayPort 2.1 Specification". VESA. 17 October 2022. Retrieved 30 October 2022.
      33. "vesa". 8 January 2024.
      34. Kowaliski, Cyril (4 May 2006). "DisplayPort 1.0 approved by VESA". www.techreport.com. The Tech Report. Retrieved 1 May 2018.
      35. 1 2 "MPEG LA Expands DisplayPort License Coverage" (PDF). 8 August 2016. Archived from the original (PDF) on 15 May 2018. Retrieved 2 May 2018.
      36. 1 2 3 4 5 6 7 8 9 10 11 DisplayPort Standard, Version 1, Video Electronics Standards Association (VESA), 1 May 2006
      37. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 DisplayPort Standard, Version 1, Revision 2, Video Electronics Standards Association (VESA), 5 January 2010
      38. Syed Athar Hussain (June 2016). "DisplayPort – Future Proofing Display Connectivity for VR and 8K HDR" (PDF). Retrieved 11 May 2018.
      39. "Thunderbolt 3 Technology Brief" (PDF). Intel Corporation. 2016. Retrieved 14 May 2018.
      40. 1 2 3 Smith, Ryan (26 June 2019). "VESA Announces DisplayPort 2.0 Standard: Bandwidth For 8K Monitors & Beyond". Anandtech.
      41. 1 2 VESA DisplayPort Standard, Version 2.1. Video Electronics Standards Association (VESA). 10 October 2022.
      42. 1 2 3 Craig Wiley (25 April 2013). "How to Choose a DisplayPort Cable, and Not Get a Bad One!". DisplayPort.org. Archived from the original on 5 July 2013.
      43. "VESA Strengthens 8K Video Resolution Ecosystem with Market-ready DP8K Certified DisplayPort Cables". Video Electronics Standards Association (VESA). 3 January 2018. Archived from the original on 14 May 2018. Retrieved 14 May 2018.
      44. 1 2 "Mini DisplayPort Connector Standard, Version 1.0". Video Electronics Standards Association (VESA). 26 October 2009. Retrieved 13 May 2018.
      45. "The DisplayPort Pin 20 Problem". Monitor Insider. Archived from the original on 14 May 2018. Retrieved 14 May 2018.
      46. Roy Santos (3 January 2008). "Dell UltraSharp 3008WFP 30-Inch LCD Monitor". PC World. Archived from the original on 23 March 2018. Retrieved 14 May 2018.
      47. VESA DisplayPort Marketing Guidelines version 1.1 (PDF), archived from the original (PDF) on 12 November 2020
      48. "DisplayPort Marketing Guidelines R14" (PDF). 8 June 2018. Archived (PDF) from the original on 25 March 2019. Retrieved 25 March 2019.
      49. "GTX 770 4gb Unable to select 144hz on dell S2716DG". 4 February 2016. Archived from the original on 30 July 2020.
      50. "Video Timings Calculator". tomverbeure.github.io. Retrieved 20 June 2022.
      51. "VESA DisplayPort (DP) Standard, Version 2.0". Video Electronics Standards Association (VESA). 26 June 2019.
      52. "LG 27UK650-W 4K UHD LED Monitor". Archived from the original on 18 November 2018.
      53. 1 2 VESA DisplayPort Interoperability Guideline, Version 1.1, VESA, 28 January 2008
      54. "VESA Introduces Updated Dual-Mode Standard for Higher Resolution Interoperability with HDMI Displays". VESA. 31 January 2013. Archived from the original on 10 May 2018. Retrieved 13 May 2018.
      55. "DisplayPortTM Ver.1.2 Overview" (PDF). Retrieved 5 July 2018.
      56. "Does the 16-inch, 2019 MacBook Pro support daisy-chaining on DisplayPort?". 30 April 2020.
      57. "MacBook Pros and (their lack of) DisplayPort MST (Multi-Stream) support: what about macOS Catalina?". 17 December 2019.
      58. "Google's USB Type-C to DP Adapter "DingDong"" . Retrieved 2 August 2018.
      59. "MPEG LA Introduces License for DisplayPort". Business Wire. 5 March 2015. Retrieved 5 March 2015.
      60. "DisplayPort Attachment 1" (PDF). 23 November 2015. Archived from the original (PDF) on 23 January 2018. Retrieved 23 November 2015.
      61. "DisplayPort FAQ". Video Electronics Standards Association (VESA). Archived from the original on 13 November 2015. Retrieved 23 November 2015.
      62. "VESA standards purchasing page".
      63. "VESA membership application".
      64. 1 2 Adhikari, Richard (9 December 2010). "VGA Given 5 Years to Live". Tech News World.
      65. "Top PC, Chip, Display Makers to Ditch VGA, DVI". PCMag.
      66. "R.I.P. VGA: Nvidia's GeForce GTX 1080 dumps analog support, following Intel and AMD's lead". PCWorld. 10 May 2016. Retrieved 2 May 2021.
      67. "DisplayPort: the next generation interface for high-definition video and audio content" (PDF). st.com. June 2010. Archived from the original (PDF) on 19 July 2014. Retrieved 15 July 2014.
      68. "Standards". Vesa. Retrieved 27 January 2016.{{cite journal}}: Cite journal requires |journal= (help)
      69. Broekhuijsen, Niels (30 December 2013). "EVGA's DisplayPort Hub Available Now". Tom's Hardware . Retrieved 7 March 2014.
      70. Moritz Förster (16 September 2014). "VESA veröffentlicht DisplayPort 1.3". heise online. Retrieved 27 January 2016.
      71. "FAQ Archive  DisplayPort". VESA. Retrieved 22 August 2012.
      72. "The Truth About DisplayPort vs. HDMI". dell.com. Retrieved 27 January 2016.
      73. "HDMI Adopter Terms". hdmi.org. HDMI Licensing. Archived from the original on 18 December 2008. Retrieved 23 June 2008.
      74. "Interview with Steve Venuti from HDMI Licensing" (PDF). hdmi.org. HDMI Licensing. Archived from the original (PDF) on 21 June 2010. Retrieved 27 January 2016.
      75. "Zotac releases DisplayPort to dual HDMI adapter". Anandtech. 2 August 2011. Retrieved 23 January 2012.
      76. "FAQ for HDMI 2.0". HDMI. Archived from the original on 5 January 2019. Retrieved 29 November 2013.
      77. "HDMI Specification 1.3a" (PDF). HDMI Licensing, LLC. 10 November 2006. Archived from the original (PDF) on 5 March 2016. Retrieved 1 April 2016.
      78. "Designing CEC into your next HDMI Product" (PDF). QuantumData.com. 2008. Archived from the original (PDF) on 4 March 2012. Retrieved 24 July 2017.
      79. Hans Verkuil (20 November 2017). "Linux drm: add support for DisplayPort CEC-Tunneling-over-AUX". Cisco. Retrieved 3 January 2018.
      80. "Understanding EDID - Extended Display Identification Data". .extron.com.
      81. "Digitimes Research: Proportion of HDMI/DisplayPort technology in LCD monitors increases 7.5pp in August". DIGITIMES. September 2014.
      82. "DisplayPort expected to surpass HDMI in 2019 - IHS Technology". technology.ihs.com.
      83. "Thunderbolt Technology: The Fastest Data Connection to Your PC Just Arrived" (Press release). Intel. 24 February 2011. Retrieved 24 February 2011.
      84. "VESA Begins Development of Micro-DisplayPort Connector Standard". DisplayPort. 23 October 2013. Retrieved 7 March 2014.
      85. "VESA Finalizes Requirements for Display Stream Compression Standard" (Press release). VESA. 24 January 2013. Archived from the original on 21 March 2018. Retrieved 20 March 2018.
      86. "Embedded DisplayPort Standard Ready from VESA" (PDF). VESA. 23 February 2009. Archived from the original (PDF) on 7 July 2012.
      87. "VESA Issues Updated Embedded DisplayPort Standard". Business Wire. 7 February 2011. Retrieved 27 January 2016.{{cite journal}}: Cite journal requires |journal= (help)
      88. "Mobile Battery Life and Display Performance Improves with Upcoming Release of eDP 1.4". VESA. 10 September 2012. Retrieved 10 November 2013.
      89. "VESA Publishes Embedded DisplayPort (eDP) Standard Version 1.4a". VESA. 9 February 2015. Retrieved 27 January 2016.
      90. "VESA Rolls Out Production-Ready Embedded DisplayPort Standard 1.4 for Mobile Personal Computing Devices". VESA. 27 October 2015. Retrieved 28 October 2015.
      91. "VESA Publishes Embedded DisplayPort Standard Version 1.5". 27 October 2021. Retrieved 28 October 2021.
      92. "VESA Issues Internal DisplayPort Standard for Flat Panel TVs" (PDF). VESA. 10 May 2010. Archived from the original (PDF) on 26 July 2011.
      93. "WiGig Alliance and VESA to Collaborate on Next Generation Wireless DisplayPort". Wireless Gigabit Alliance.{{cite journal}}: Cite journal requires |journal= (help)
      94. "VESA Experiences Acceleration of MyDP Standard Adoption in Mobile Devices". Archived from the original on 22 March 2016. Retrieved 10 March 2014.
      95. "Support  Slimport". Us.slimportconnect.com. 18 July 2013. Archived from the original on 23 March 2016. Retrieved 11 March 2014.
      96. "Releases MyDP Standard". VESA. 27 June 2012. Archived from the original on 17 March 2016. Retrieved 10 November 2013.
      97. "Experiences Acceleration of MyDP Standard Adoption in Mobile Devices". VESA. 9 November 2012. Retrieved 10 November 2013.
      98. "Hands on with the Analogix SlimPort microUSB to HDMI and VGA adapters". AnandTech. Retrieved 31 December 2013.
      99. "SlimPort". Archived from the original on 9 April 2016. Retrieved 31 December 2013.
      100. "VESA Refreshes DisplayID Standard to Support Higher Resolutions and Tiled Displays". vesa.org. 23 September 2013. Archived from the original on 8 February 2015. Retrieved 24 December 2013.
      101. "Gaming At 3840x2160: Is Your PC Ready For A 4K Display?". tomshardware.com. 19 September 2013. Retrieved 26 December 2013.
      102. "MD/TI's DockPort Adopted As Official Extension to DisplayPort Standard". anandtech.com. Retrieved 12 January 2014.
      103. "DisplayPort Alternate Mode for USB Type-C Announced  Video, Power, & Data All Over Type-D". anandtech.com. Retrieved 14 October 2014.
      104. "Dell UltraSharp 3008WFP 30-Inch LCD Monitor". The Washington Post. Retrieved 25 June 2008.
      105. "AMD Receives First Ever DisplayPort Certification for PC Graphics". AMD. 19 March 2008. Retrieved 23 January 2012.
      106. Kirsch, Nathan (21 February 2008). "EVGA, Palit and XFX GeForce 9600 GT Video Card Review". Legit Reviews. Retrieved 2 April 2013.
      107. "Software Licensing and Trademark Agreement: Mini DisplayPort".
      108. "Apple Mini DisplayPort Connector Implementation License Checklist" (PDF). Apple. Retrieved 4 December 2008.
      109. "ATI Radeon HD 5870 1GB Graphics Card and AMD Eyefinity Review". PC Perspective. 23 September 2009. Archived from the original on 27 September 2009. Retrieved 23 September 2009.
      110. "Signs of the Times: Massive Digital Signage Displays Powered by Diminutive Graphics Card". The Official NVIDIA Blog. Archived from the original on 6 November 2015. Retrieved 1 March 2024.
      111. Williams, Daniel. "NVIDIA Launches NVS 810 Digital Signage Video Card". www.anandtech.com. Archived from the original on 5 November 2015. Retrieved 1 March 2024.
      112. "NVIDIA GeForce 10 Series Graphics Cards". NVIDIA.
      113. "Radeon RX 480-Grafikkarten  AMD". www.amd.com.
      114. "VESA Highlights Growing DisplayPort Alt Mode Adoption and Latest DisplayPort Developments at Mobile World Congress". VESA - Interface Standards for The Display Industry. 15 February 2017.
      115. "Search | Device Specs | PhoneDB - The Largest Phone Specs Database". phonedb.net.
      116. "SlimPort". www.slimportconnect.com.
      117. "Analogix announces DisplayPort transmitter". 26 August 2006. Archived from the original on 24 June 2013. Retrieved 10 August 2009..
      118. "Chrontel".
      119. "Genesis Microchip (GNSS) Q4 2006 Earnings Conference Call". Seeking Alpha. 2 May 2006. Retrieved 16 July 2007.
      120. "Samsung touts development of first DisplayPort desktop LCD". TG Daily. 25 July 2006. Archived from the original on 26 September 2007. Retrieved 25 July 2007.
      121. "Worldwide First DisplayPort MB". 25 March 2008. Archived from the original on 15 January 2009. Retrieved 10 August 2009.
      122. "DataPro DisplayPort Cables".
      123. "MSI announces video adaptor with DisplayPort". 17 January 2008. Archived from the original on 19 December 2013. Retrieved 10 August 2009.