| HD.26 | |
|---|---|
 | |
| Role | Single seat shipboard fighter aircraftZ]] |
| National origin | France |
| Manufacturer | Aeroplanes Hanriot et Cie |
| First flight | 1923 |
| Number built | 1 |
The Hanriot H.26 was a French single seat fighter aircraft prototype completed in 1923. Only one was built.
The H.26 (the first Hanriot fighter that did not use the HD nomenclature, where the D was for their long-standing designer Emile Dupont) was intended for the 1921 C1 (single seat Chasseur or fighter) programme competition. Most participants used the 300 hp (224 kW) V-8 Hispano-Suiza 8F engine, with its low frontal area. Instead, the H.26 used a lower power, 260 hp (194 kW) water cooled Salmson 9Z 9-cylinder radial engine. The H.26 aimed to redress the balance by aerodynamic cleanliness, with few interplane struts, flying wires or exposed cabane struts. [1]
It was an all-metal single bay sesquiplane, fabric covered except for the fuselage ahead of the cockpit. The gap between the wings was small and the stagger marked. The lower wing was conventionally mounted at the bottom of the fuselage and the upper planes, built in separate pieces, braced close to the upper fuselage on short, faired extensions. [1] In section the wings were aerodynamically thick and strongly cambered. [2] There were ailerons only on the upper plane, [1] the plan, structure and bracing of which was greatly altered during 1923. When the H.26 made its first public appearance, at the Paris Aero Show in December 1922, the still uncovered upper wing of the unflown fighter had long, gently curved tips outboard of a straight edged, constant chord central section and had a single main spar. [2] [3] Sixteen months later, after the aircraft had flown, the wings had become rectangular and were built around two spars. [4] The short span lower wing retained its single spar structure throughout but it, too, had curved tips replaced with square. [2] [3] [4] The wing bracing had also changed: originally a bracing wire ran from the rear undercarriage structure upwards and outwards, via the lower to the upper wing. This was replaced by a single, wide chord rigid strut with an aerofoil section and widened at its roots. [1] [4]
The closely cowled radial engine set the diameter of the H.26's short nose and drove a two blade propeller behind a very large diameter domed spinner. The Salmson was initially cooled with a semi-circular Botali radiator to the rear of the engine but this proved ineffective and was replaced with a pair of Chaussons, one on each forward undercarriage leg. [1] The H.26 had a fixed conventional undercarriage with mainwheels on a centrally hinged split axle, enclosed within a lift-contributing wing-like fairing and supported by N-form struts attached to the lower fuselage longerons on each side. Originally, these were reinforced by long vertical struts from the shock absorber attachments to the upper wing central section. [2] These were discarded when the interplane wires were replaced by the faired interplane struts, which extended downwards to the rear undercarriage structure; the tops of the shock absorber struts were relocated to mid-fuselage on the engine mounting. [1] [4]
The pilot's cockpit, with a faired headrest behind it, was at the trailing edge of the upper wing, placed within a small cut-out to improve his limited view. [1] The H.26 had a fuselage built around four metal tube, cross-braced longerons, enclosed within metal formers and stringers to shape it into an oval cross-section. [4] Behind him the fuselage tapered to the broad chord fixed tail surfaces. The mid-fuselage tailplane, which had a strongly swept leading edge, carried round tipped elevators that narrowed inboard. The vertical tail was oval shaped, with a broad chord rudder that ended at the top of the fuselage. [1]
The H.26 was first flown from Orly in 1923. Initially troubled by engine overheating, it proved to have handling problems and a poor view for the pilot; despite the modifications, its test programme was soon abandoned. [1]
Data from Green & Swanborough p.279 [1]
General characteristics
Performance
The Latécoère 4 was a three-engined, 15-passenger biplane built in France in the early 1920s. It proved difficult to fly and was discontinued, though a second machine was completed as the Latécoère 5 bomber.
The Hanriot HD.6 was a French two-seat fighter aircraft prototype, built towards the end of World War I though not flown until after the armistice with Germany. A biplane with an unusually narrow gap between upper and lower wings, powered by a single water-cooled radial engine, it did not enter production.
The Meyers Midget was a one-off small, low-powered, sporting single-seat sesquiplane, designed and built in the United States in 1926, incorporating several innovative structural features.
The Fokker D.XII was a Dutch single seat, single engine fighter aircraft designed to an American specification which called for the use of a Curtiss D-12 engine, designated PW-7. Despite considerable efforts to improve the airframe, Fokker failed to win the USAAS competition.
The Dewoitine D.15 was a single-engine, single-seat biplane fighter aircraft built in France in the 1920s. Intended to offer structural simplifications when compared with monoplanes, it had a disappointing performance and was soon abandoned.
The Hanriot HD.5 was a French two-seat fighter aircraft prototype, built towards the end of World War I. A single-engine biplane with an unusually narrow gap between the upper and lower wings, it did not enter production.
The Hanriot HD.15 was a French two seat fighter aircraft fitted with a supercharger for good high altitude performance, built in the 1920s. Three were ordered by Japan but lost at sea during delivery.
The Hanriot HD.20 was a French single seat shipboard fighter aircraft prototype completed in 1923. Only one was built.
The Hanriot H.31 was a single engine, single seat French biplane fighter aircraft built in 1925 to compete in a government programme. It was not successful and only one prototype was completed.
The LFG Roland D.XV was a World War I German single seat fighter aircraft, ordered as a test-bed for engine comparisons. It was distinguished from earlier Roland biplane designs by the elimination of flying wires. Two later aircraft, also called LFG Roland D.XV, were completely different designs with slab sided fuselages.
The Potez 26 was a single seat fighter aircraft designed and flown in France in the mid-1920s. It did not reach production.
The Caudron C.220 was a two-seat French biplane trainer. Only two were built, using different engines.
The Caudron C.140 was a French tandem cockpit sesquiplane designed in 1928 as a combination of liaison aircraft and observer and gunnery trainer.
The Caudron Type D was a French pre-World War I single seat, twin-boom tractor biplane, a close but slightly smaller relative of the two seat Caudron Type C. More than a dozen were completed, one exported to the United Kingdom, where they may also have been licence built, and three to China.
The Potez 24 A.2 was a mid-1920s French biplane intended to replace the Potez 15 as an army observation aircraft. The further improved and larger Potez 25 was preferred for production.
The Magni PM.2 Vittoria was an Italian experimental, single seat, parasol wing aircraft built in the mid-1920s. It had a large area aerofoil on each of its single wing bracing struts which could be rotated together or independently to give lift or drag.
The Hanriot H.25 was a French, single-engined, six passenger airliner built in 1926. Only one was flown.
The Skraba S.T.3 was a two-seat Polish biplane built in 1928. It was the first all-metal aircraft designed in Poland; only one was completed.
The Morane-Saulnier MS.152 was a French multi-purpose aircraft built in 1928. It did not go into production.
The Borel C.A.P. 2, later SGCIM C.A.P. 2, was a prototype, all-metal framed, high-altitude sesquiplane fighter and reconnaissance aircraft with a supercharged engine, built in France around 1920. It was displayed, uncovered, at the 1922 Paris Salon.