Country of origin | Australia |
---|---|
Introduced | 1942 |
No. built | about 250 [a] |
Type | early warning |
Frequency | 200 MHz |
PRF | 50 pps |
Pulsewidth | 10 μS |
RPM | manual rotation |
Range | over 100 mi (160 km) |
Azimuth | 360º |
Power | 10 kW Mk. I, 160 to 200 kW Mark III |
Other Names | LW/AW, A286Q |
The Light Weight Air Warning Radar, or LW/AW was a portable early warning radar produced in Australia during the Second World War. It was designed by the Council for Scientific and Industrial Research, today's CSIRO, to provide field troops with air attack warning in the northern Australia and New Guinea theatres.
From 1940, CSIR had been designing a large system known as Air Warning, Mark I (AW.1) for fixed emplacements, similar in concept to the UK's Chain Home. The first Japanese air attacks on Darwin were carried out before it was in place, and it was some time before this larger unit could be put into action. This led to a December 1941 request for a smaller version that could be held in reserve and the moved into location if the AW system was attacked. Shortly thereafter, field units requested a portable system that could be quickly delivered to forward airfields. Work began at CSIR in the summer of 1942 on a system that would fill both needs.
The LW/AW emerged as a system designed to be carried in rough conditions and small and light enough to fit in the Douglas DC-2 and Douglas Dakota. Otherwise similar to the AW, a new antenna design based on the UK's Chain Home Low provided the desired range in a robust multi-unit array that could be easily assembled in the field. The prototype entered testing in September 1942, and the first two production models were moved to New Guinea in mid-October and entered full operation on 8 November. The Mark I and slightly modified Mark IA served until the end of the war with about 260 produced.
The Mark II had a larger cabin and modified antenna to support IFF Mark III but was otherwise similar. Mark III, was introduced in 1944, but the earlier versions were so successful it was not put into production. A modification of the Mk. III was used on ships as the A286Q and about 120 were produced.
In early 1939, the British government invited teams from Canada, Australia, New Zealand and South Africa to visit the UK to be briefed on the then highly secret developments in radar. [1] In September, with the opening of World War II, the Radio Physics Laboratory (RPL) of the Council for Scientific and Industrial Research began development of a surface-search radar, known as Shore Defence, or SHD. SHD was similar to the UK's own Coast Defense system (CD), but added a switch that allowed a single antenna to be used both for transmission and reception, simplifying the system compared to the two-antenna CD. The first SHD was installed in Dover Heights near the entrance to Sydney Harbour. [2]
As attention turned to the threat of air attack, the SHD system was modified with a different antenna layout to allow it to scan to higher angles. This produced the Air Warning radar, or AW Mark I. Although this was a powerful system, with detection on bomber-sized targets out to the range of 100 miles (160 km), it was also relatively large and could only be delivered by ship. Shipping the system took time, and assembly even longer. The system intended for Darwin, which was in range of Japanese bombers from New Guinea, was still being prepared when the first attack took place on 19 February 1942. [2] Darwin was subject to repeated attack, yet it still took another seven weeks before the first set was operational. [3]
In December 1941, Wing Commander A.G. Pitcher suggested the Royal Australian Air Force (RAAF) produce a number of smaller mobile radar systems to act as backup in case the AW sites were attacked. These would be held off-site and moved to the original AW location on demand. Doing so would require a smaller and more mobile system. In January 1942, Flying Officer B.F.N. Israel returned from working with the Royal Air Force (RAF) in Singapore and stressed that there was a need for a truly mobile system that could be used in the field. Israel was posted to Sydney as the radar liaison officer between the RPL and HMV, the manufacturer. [2]
By the summer of 1942, the Australian Army was advancing and setting up new airfields. The need for early warning sets at these advanced bases was a serious concern as they were within easy attack range from several Japanese airfields. Pither sent a memo to John Worledge of the NSW Railways who was leading a group that produced the mechanical structures for the AW and SHD sets. Pither suggested that the electronics from the AW were suitable for mobile use if packaged correctly, but the antenna system needed to be produced in a version that could be flown into these airfields using Douglas DC-2 aircraft, which formed the basis of the Australian Transport Command. Pither also copied Israel and Squadron Leader Mitchell, Commander of the Radio School at Richmond. [4]
Pither suggested one way to reduce the size of the antenna would be to remove one horizontal row of elements. But this would reduce the power by 1⁄3 and greatly reduce range. Israel, who had seen the Chain Home Low (CHL) systems in Singapore, was aware of their layout. He liaised with J.L. Pawsey, an expert in antenna design at the RPL, who produced a new design of four rows of eight dipoles, which maintained 89% of the original antenna gain and improved electronics regained another 5%. But the main benefit was that the antenna was now made up of eight 2 by 2 element cubes that were small enough for air transport and could be connected together in the field. The system was later referred to as the "Worledge aerial system". [5]
The prototype system was completed in September 1942, and shipped to Dover Heights for testing. [b] The first two production units were flown to Papua New Guinea some time in October. The first was set up at Tufi Airport and went operational on 8 November. Getting the system in place was a difficult job:
The equipment was erected and tested on the outskirts of Port Moresby and then flown over the Owen Stanleys... The gear was then moved overland through the swamps and jungle and across unbridged creeks to the sea. To get to the trawler outside the reefs, the gear was loaded on platforms formed between pairs of native canoes lashed together. [7] The trawler arrived at McLaren Harbour on 30 October 1942, a fiord with cliffs rising 200 ft above the sea level. [7] The gear and all supplies were manhandled [to the top]. It was then carried about three and a half miles to the site on the promontory. [7]
The second unit was operational at Dobodura Airfield on 3 December. Dobodura was a forward location near Buna Airfield, which was itself captured on 14 December 1942. Further units continued to arrive in the theatre, at which point several problems were first noticed. One was that when the radar was turned off for maintenance, the cooling electronics would lead to significant condensation inside the system, which in turn led to the development of fungi inside the units. [8] The problem was considered so severe that in late 1942, WWI Field Marshal Thomas Blamey was put in charge of getting the problems solved. In early 1943 field units were sent a 205 W electrical heater that automatically turned on when the electronics turned off. This maintained the temperature within the two large equipment chassis. [8]
Other changes were more minor. The packaging continued to be improved through this period, and its ability to float if dropped in the water was tested in Sydney Harbour and the surf at Manly Beach. Another change was to raise the height of the turntable over the ground, as it was noticed airflow under the equipment was too low to properly cool the bottom of the chassis. These changes were formalized as LW/AW Mark IA. Over 260 Mark I and Mark IAs were produced. [8]
In April 1942, the supply of the US built VT90 micropup vacuum tubes that powered the transmitter ran low. An effort began to use an alternative design, the 100TH Eimac. These proved to be able to generate much greater output than the VT90s of the Mark I, and would offer significant gains in effective range. This was not so important for the LW role, but too-short range had proven to be a significant problem for the fixed-place AW units which were typically protecting larger areas like cities. An effort began to replace these with the new units as AW Mark II, which used four of the Eimac tubes in a ring to produce peak power of 50 kW. This was also adapted with a smaller antenna as the A79, for small ships. The first production examples arrived in December 1942, but these proved difficult to keep operational in the field, Supplies of the VT90 improved and the AW Mark II was dropped after only 15 were produced. [8]
By 1943, IFF Mark III was being widely introduced in the US forces, and ad-hoc additions to LW/AW were common. In the second half of the year, a rush effort began to build a more formal solution to connecting the US-built BL3 IFF interrogator units and make them part of the standard equipment list. The IFF antennas were placed on top of the existing antenna array. At the same time, operator complaints about the existing cramped tent leading to poor airflow and resulting high temperatures and humidity led to an effort to design a larger enclosure. This new system became the LW/AW Mark II. [9]
One of the first Mark II units was sent to Bipi Island in early 1944 as part of the Admiralty Islands campaign. It arrived on 5 April and had to be ferried ashore on the local's canoes. The site proved to be poor and it was moved to Los Negros Island in May. before moving agin to Manus Island on 26 July. But the time it was operational again it had been moved eighteen times and yet was only non-operational for five hours in nineteen months of operations. [9]
An improved version of the micropup, the NT99, began to arrive around the same time. When applied to the AW electronics, it allowed the power to be increased to 150 kW. An experimental version was operational in July 1943, which revealed that the power was so much that the antenna feeder lines of the LW/AW set would have to be modified. A prototype of the resulting LW/AW Mark III was sent to Los Negros in February 1944. The next month, Bruce Alexander who had worked on the transmitter design, flew to test the unit and related that just before arrived the unit had picked up an aircraft up to 92 miles (148 km) which was invisible to the Mark I. [9] This turned out to be a C-47 that was lost, and fighters were sent to escort it to the airfield. [10]
Although the Mark III proved to be a more powerful unit, it was not put into widespread production due to the earlier versions working well enough and the complications that the new parts would cause in logistics. [10]
In August 1942, an effort began to develop a ground controlled interception (GCI) radar. GCI is used to direct fighter aircraft onto their targets, and thus needs to have higher resolution than an early warning design that simply has to show the rough location of targets. Additionally, the A-scope type display used for the EW role is not useful for GCI, where the radar needs to display the locations of both the target and the interceptor at the same time. This demands the use of a plan position indicator (PPI) display. On the other hand, range requirements are generally lessened as another radar would already be providing early warning. [10]
This led to the LW/GCI Mark I, which was heavily modified from the original LW/AW. Its electronics were taken from a US SCR-602 Type 6 and a new antenna support system that separated the original two rows of antennas vertically. By switching between the two arrays, the vertical lobes of the transmitter beams could be used to measure altitude. The PPI display was taken from the British Coast Artillery Number 2 radar. The system proved to have poor altitude performance above 20,000 feet (6,100 m), but was still useful enough that an order for twenty sets was placed by the US forces. [10]
Development of an improved model, LW/GCI Mark II, began in March 1944. This modified the 602 transmitter for improved reliability, added a preamplifier on the receiver to improve its sensitivity, and changed the antenna system to use three arrays of 2 by 12 dipoles which offered both better height measure and more angular resolution. Although the improvements were considerable, only limited production was started due to the imminent arrival of new units operating in the microwave range. [10]
A somewhat more limited update started in January 1943 to add height finding to the existing LW/AW sets. The LW/AWH Mark I was essentially two Mark IA antennas stacked on top of each other. By connecting to one antenna or the other, the lobes in the reception patterns shifted vertically and allowed the operator to calculate altitude. Only four units were produced in favour of microwave systems. [10]
When the microwave systems arrived, they required two separate radars, one for PPI direction and separate systems for height finding. The system massed 35 long tons (36 t) compared to the 2 long tons (2.0 t) limit for operations in the South Pacific. This led to efforts to develop a new lightweight height finder, using a locally-designed cavity magnetron operating at 25 cm wavelength. Work on this LW/AWH Mark III began in February 1944. The naming was retained despite it being entirely dissimilar to the earlier models. [11]
With the ending of the war, US radar systems that were being built in huge numbers were suddenly surplus, and sold off for very low prices. The AN/TPS-1 replaced older units like the LW/AW very quickly in many forces. This, in turn, led to the LW/AW becoming surplus as well, and finding use in secondary roles. The Department of Civil Aviation installed a LW/AW at Essendon Airport in Melbourne, at that time the busiest airport in Australia. The installation did not prove useful, and was later replaced by an ex-Royal Navy Type 276 radar under the name Aerodrome Control Radar. [12]
A stated goal of the system was that no single part would mass more than 200 pounds (91 kg). This was relatively easy for most of the electronics and the antenna systems, but was more difficult for the power supply, which consisted of a 5 kW generator run by the engine from a Ford 10. This too was ultimately broken down into parts, consisting of the engine, the alternator and flywheel, radiator, exhaust along with various other parts, underlying chassis, and the control panel. Only two of these ultimately went over the desired mass limits, the engine at 250 lbs and the alternator and flywheel at 450. In almost every case, the units could not be landed at a pier, or even on the beach, most were required to offload outside of a reef and then be carried ashore. For this reason, all of the packs were watertight. [6]
Setup at the site started with the operations tent, which used a steel space-frame that could be lifted into position and then covered with the tent fabric. The uppermost part of the framework consisted of a square metal plate containing a bearing. The antenna support consisted of a turntable that sat on the floor of the tent and had a mast projecting upward and through the bearing at the top. The antenna was then built up on top of this mast. The antenna support structure consisted of eight separate steel frameworks that looked similar to scaffolding and were assembled into a two-high, four-wide arrangement. There were two different support designs, one that was thicker and formed the inner portion and connected to the mast, and a thinner section that formed the outer "wings". When assembled, the framework was roughly lenticular, thick in the center and thin at the sides. Four dipole antenna elements were then connected to the face of each support and wired together at the center using 330 Ohm twin-lead. This produced an eight-wide, four-high array. [13]
The electronics were packaged into two large chassis, placed one each on either side of the mast. The entire equipment section rotated together on the turntable, along with the two operator's chairs, in order to turn the antenna for searching. [14] The cabinet on the right, as seen from the operator's side, housed the radio receivers and cathode ray tube (CRT) displays and was the main operator's station. The cabinet on the left contained the transmitter and other radio equipment. The operator at this station was primarily tasked with rotating the antenna using a large handwheel on the mast. [12]
The Mark IA differed only in detail, adding the IFF antennas on top. This consisted of a transmitter antenna mounted directly on top of the existing antenna. This was similar in size and shape as any single framework from the main antenna. Above this was a much smaller receiver, as well as a horizontal square metal mesh that prevented the signals from the antennas below being seen in the receiver. The Mark III was otherwise identical, differing only in the electronics in the cabinets. [13] The GCI versions differed largely by adding a new triangular framework between the two rows, raising the upper two rows of dipoles higher into the air. [14]
In the field, the GCI systems proved to have many problems, and the Mark II versions replaced the original tent with a plywood hut that rotated with the antennas. The entire assembly was then mounted on a large four-legged steel ground support similar to the systems used to support large anti-aircraft artillery guns. [15]
The original sets were used for early warning only. The operators would swing the antenna back and forth across likely approach routes and watch for echos that would appear on the 5 inches (130 mm) diameter CRT. This was arranged as it was in Chain Home, in A scope fashion, with a scale along the top and the blips deflecting the beam downward. The operator could read the range to the target by comparing the location of a blip to the scale above it. The scale was calibrated to 80 miles (130 km), [15] although it was common to see returns beyond that under good conditions and ranges as great as 150 miles (240 km) were achieved on occasion. [6]
The GCI units added a second CRT to act as a PPI display. This used selsyns connected to the antenna mast that physically rotated the CRT's deflection coils so that the line on the display was rotated to the same angle as the antenna. The same time base generator was used as the A scope, but adjusted so that the line it created only covered half of the display and was moved so it started from the center and drew outwards. Combined with the angle adjustment, this created the classic "sweeping line" type of radar display with blips appearing as dots at a given distance and angle from the station. As both the target and the attacking fighters were visible at the same time, the operator could easily direct the fighters towards the targets. [14] The original A scope now served primarily as the height-finding system, displaying the returns from the two antenna arrays at the same time, causing two blips to appear for each target. The distance between the two gave a measure of the angle above the horizon. [15]
Identification, friend or foe (IFF) is a combat identification system designed for command and control. It uses a transponder that listens for an interrogation signal and then sends a response that identifies the broadcaster. IFF systems usually use radar frequencies, but other electromagnetic frequencies, radio or infrared, may be used. It enables military and civilian air traffic control interrogation systems to identify aircraft, vehicles or forces as friendly, as opposed to neutral or hostile, and to determine their bearing and range from the interrogator. IFF is used by both military and civilian aircraft. IFF was first developed during World War II, with the arrival of radar, and several friendly fire incidents.
The SCR-270 was one of the first operational early-warning radars. It was the U.S. Army's primary long-distance radar throughout World War II and was deployed around the world. It is also known as the Pearl Harbor Radar, since it was an SCR-270 set that detected the incoming raid about 45 minutes before the 7 December 1941, attack on Pearl Harbor commenced.
The Naxos radar warning receiver was a World War II German countermeasure to S band microwave radar produced by a cavity magnetron. Introduced in September 1943, it replaced Metox, which was incapable of detecting centimetric radar. Two versions were widely used, the FuG 350 Naxos Z that allowed night fighters to home in on H2S radars carried by RAF Bomber Command aircraft, and the FuMB 7 Naxos U for U-boats, offering early warning of the approach of RAF Coastal Command patrol aircraft equipped with ASV Mark III radar. A later model, Naxos ZR, provided warning of the approach of RAF night fighters equipped with AI Mk. VIII radar.
Ground-controlled interception (GCI) is an air defence tactic whereby one or more radar stations or other observational stations are linked to a command communications centre which guides interceptor aircraft to an airborne target. This tactic was pioneered during World War I by the London Air Defence Area organization, which became the Royal Air Force's Dowding system in World War II, the first national-scale system. The Luftwaffe introduced similar systems during the war, but most other combatants did not suffer the same threat of air attack and did not develop complex systems like these until the Cold War era.
Serrate was a World War II Allied radar detection and homing device that was used by night fighters to track Luftwaffe night fighters equipped with the earlier UHF-band BC and C-1 versions of the Lichtenstein radar. It allowed RAF night fighters to attack their German counterparts, disrupting their attempts to attack the RAF's bomber force.
The AN/TPS-43 is a transportable air search 3D radar produced in the United States originally by Westinghouse Electric Corporation's Defense and Electronic Division, which was later purchased by Northrop Grumman. It is used primarily for early warning and tactical control, often for control over an associated surface-to-air missile battery or airfield. It is designed to be transported in two M35 cargo trucks and easily air-transportable on two pallets.
Radar in World War II greatly influenced many important aspects of the conflict. This revolutionary new technology of radio-based detection and tracking was used by both the Allies and Axis powers in World War II, which had evolved independently in a number of nations during the mid 1930s. At the outbreak of war in September 1939, both the United Kingdom and Germany had functioning radar systems. In the UK, it was called RDF, Range and Direction Finding, while in Germany the name Funkmeß (radio-measuring) was used, with apparatuses called Funkmessgerät . By the time of the Battle of Britain in mid-1940, the Royal Air Force (RAF) had fully integrated RDF as part of the national air defence.
The Type 271 was a surface search radar used by the Royal Navy and allies during World War II. The first widely used naval microwave-frequency system, it was equipped with an antenna small enough to allow it to be mounted on small ships like corvettes and frigates, while its improved resolution over earlier radars allowed it to pick up a surfaced U-boat at around 3 miles (4.8 km) and its periscope alone at 900 yards (820 m).
Aircraft interception radar, or AI radar for short, is a British term for radar systems used to equip aircraft with the means to find and track other flying aircraft. These radars are used primarily by Royal Air Force (RAF) and Fleet Air Arm night fighters and interceptors for locating and tracking other aircraft, although most AI radars could also be used in a number of secondary roles as well. The term was sometimes used generically for similar radars used in other countries, notably the US. AI radar stands in contrast with ASV radar, whose goal is to detect ships and other sea-surface vessels, rather than aircraft; both AI and ASV are often designed for airborne use.
Radar, Gun Laying, Mark III, or GL Mk. III for short, was a radar system used by the British Army to directly guide, or lay, anti-aircraft artillery (AA). The GL Mk. III was not a single radar, but a family of related designs that saw constant improvement during and after World War II. These were renamed shortly after their introduction in late 1942, becoming the Radar, AA, No. 3, and often paired with an early warning radar, the AA No. 4, which was also produced in several models.
The Type 277 was a surface search and secondary aircraft early warning radar used by the Royal Navy and allies during World War II and the post-war era. It was a major update of the earlier Type 271 radar, offering much more power, better signal processing, new displays, and new antennas with greatly improved performance and much simpler mounting requirements. It allowed a radar with performance formerly found only on cruisers and battleships to be fitted even to the smallest corvettes. It began to replace the 271 in 1943 and was widespread by the end of the year.
IFF Mark II was the first operational identification friend or foe system. It was developed by the Royal Air Force just before the start of World War II. After a short run of prototype Mark Is, used experimentally in 1939, the Mark II began widespread deployment at the end of the Battle of Britain in late 1940. It remained in use until 1943, when it began to be replaced by the standardised IFF Mark III, which was used by all Allied aircraft until long after the war ended.
IFF Mark III, also known as ARI.5025 in the UK or SCR.595 in the US, was the Allied Forces standard identification friend or foe (IFF) system from 1943 until well after the end of World War II. It was widely used by aircraft, ships, and submarines, as well as in various adaptations for secondary purposes like search and rescue. 500 units were also supplied to the Soviet Union during the war.
Searchlight Control, SLC for short but nicknamed "Elsie", was a British Army VHF-band radar system that provided aiming guidance to an attached searchlight. By combining a searchlight with a radar, the radar did not have to be particularly accurate, it only had to be good enough to get the searchlight beam on the target. Once the target was lit, normal optical instruments could be used to guide the associated anti-aircraft artillery. This allowed the radar to be much smaller, simpler and less expensive than a system with enough accuracy to directly aim the guns, like the large and complex GL Mk. II radar. In 1943 the system was officially designated Radar, AA, No. 2, although this name is rarely used.
The AMES Type 82, also widely known by its rainbow codename Orange Yeoman, was an S-band 3D radar built by the Marconi Company and used by the Royal Air Force (RAF), initially for tactical control and later for air traffic control (ATC).
The AMES Type 80, sometimes known by its development rainbow code Green Garlic, was a powerful early warning (EW) and ground-controlled interception (GCI) radar developed by the Telecommunications Research Establishment (TRE) and built by Decca for the Royal Air Force (RAF). It could reliably detect a large fighter or small bomber at ranges over 210 nautical miles, and large, high-flying aircraft were seen out to the radar horizon. It was the primary military ground-based radar in the UK from the mid-1950s into the late 1960s, providing coverage over the entire British Isles.
Radar, Air-to-Surface Vessel, Mark III, or ASV Mk. III for short, was a surface search radar system used by RAF Coastal Command during World War II. It was a slightly modified version of the H2S radar used by RAF Bomber Command, with minor changes to the antenna to make it more useful for the anti-submarine role. It was Coastal Command's primary radar from the spring of 1943 until the end of the war. Several improved versions were introduced, notably the ASV Mark VI, which replaced most Mk. IIIs from 1944 and ASV Mark VII radar, which saw only limited use until the post-war era.
The AMES Type 7, also known as the Final GCI, was a ground-based radar system introduced during World War II by the Royal Air Force (RAF). The Type 7 was the first truly modern radar used by the Allies, providing a 360 degree view of the airspace around the station out to a distance of about 90 miles (140 km). It allowed fighter interceptions to be plotted directly from the radar display, a concept known as ground controlled intercept, or GCI.
The SCR-602 also known as the AN/TPS-3, was a mobile, lightweight, medium-range, early-warning radar utilized by the United States and its allies during World War II. The radar was originally designed for use during the initial stages of an amphibious assault or military operation where its lightweight relative to other radar systems was a distinct advantage. Once larger radars such as the SCR-270 or AN/TPS-1 came online the SCR-602 could also be used to fill in gaps in radar coverage.
AMES Type 6, also known as the Light Warning Set or L/W, was a portable early warning radar developed by the Air Ministry Experimental Station (AMES) for use by the Royal Air Force (RAF) in the field. Units in British Army service were officially known as Radar, Anti-Aircraft, Number 4, or AA. No. 4 for short, although this name was rarely used in practice. The system was also built in Canada for use by the US Army, who referred to them as SCR-602-A.