Country of origin | United Kingdom |
---|---|
Introduced | July 1939 |
No. built | 100+ |
Frequency | 200 MHz |
PRF | 400 Hz |
Beamwidth | 1.5° (horizontal) |
Pulsewidth | 3 μs |
RPM | Up to 3.3 |
Power | 150 kW |
Other Names | AMES Type 2, CD Mark I |
Chain Home Low (CHL) was the name of a British early warning radar system operated by the RAF during World War II. [2] The name refers to CHL's ability to detect aircraft flying at altitudes below the capabilities of the original Chain Home (CH) radars, where most CHL radars were co-located. CHL could reliably detect aircraft flying as low as 500 feet (150 m). The official name was AMES Type 2, referring to the Air Ministry Experimental Station at Bawdsey Manor where it was developed, but this name was almost never used in practice.
The system had originally been developed by the British Army's research group, also based at Bawdsey, as a system for detecting enemy shipping in the English Channel. It was built using the electronics being developed for the aircraft interception radar systems, which worked on the 1.5 m band. This high frequency (200 MHz), for the era, allowed it to use smaller antennas that could be swung back and forth to look for returns, in contrast to the enormous fixed antennas of the 6.7 m wavelength (45 MHz) Chain Home system.
When the war began, the Luftwaffe began mine-laying missions where the bomber aircraft would fly almost all of their mission at low altitude. Chain Home could only see targets above 1.5 degrees over the horizon, so these aircraft only became visible at short range. Robert Watson Watt seized several dozen of the Coastal Defense (CD) systems that were in final construction and installed them at CH stations and key locations along the seashore to fill this critical gap in the coverage.
CHL remained an important part of the Chain network for the rest of the war, and was retained in the post-war era until it was replaced during the ROTOR upgrades by the AMES Type 80. The electronics, notably the high-power transmitter, was also re-used in a number of other systems, including the AMES Type 7.
CHL traces its origins to early experiments with aircraft interception radar systems in 1936. These were developed as a short-range radar that would be used to close the gap between Chain Home's (CH) approximate 5 miles (8.0 km) accuracy and the visual range of a night fighter pilot at about 1,000 yards (0.91 km). Developed by a team at Bawdsey Manor led by "Taffy" Bowen, the new radar had to operate at much shorter wavelengths in order to limit the antenna sizes to something that could be practically fit on an aeroplane. After considerable experimentation, the team settled on a set working at 1.5 meter wavelength, about 193 MHz in the VHF band.
In early experiments with the new set, the team found that detection of other aircraft was problematic due to their target's relatively small size, but especially due to reflections off the ground. The latter caused a very strong signal that appeared to be at a range equal to the aircraft's current altitude, and everything beyond that was invisible in the resulting clutter. This meant that a typical night bombing run by German aircraft at 15,000 feet (4,600 m) altitude would only become visible at that range, far less than the desired minimum of 5 miles (26,000 ft).
These same experiments demonstrated an unexpected side-effect. As the aircraft flew around over Bawdsey, which is located on the coast of the English Channel, the team found strong constant returns that they later realised were the cranes at the Harwich docks, miles away. Other smaller returns were quickly identified as boats in the Channel. These were being detected at ranges far beyond the maximum range against aircraft, in spite of the antennas not being designed for this role.
The potential of this discovery was not lost, and Robert Watson-Watt asked the team to demonstrate the concept in a real-world setting. A series of military exercises in the Channel in September 1937 provided a perfect test. On 3 September the team's test aircraft, Avro Anson K6260, detected several Royal Navy ships in the Channel, and the next day repeated this performance in spite of almost completely overcast skies. Albert Percival Rowe of the Tizard Committee later commented that "This, had they known, was the writing on the wall for the German Submarine Service." [3]
The British Army was actually the first to consider radar, when Alan Butement and P. E. Pollard submitted a paper in 1931 suggesting using pulses of radio signal to measure the distance to ships. [4] The Army was uninterested until they heard about Watt's work at Bawdsey, when they suddenly became very interested. In October 1936 a liaison team led by Edward Paris and Albert Beaumont Wood was set up at Bawdsey, officially known as the Military Applications Section, but universally referred to as the "Army Cell". [5]
Ironically, the only two technicians with the required experience available were Butement and Pollard. The two quickly began development of two projects, the Mobile Radar Unit (MRU) which was a mobile version of Chain Home, and Gun Laying radar, a much smaller unit designed to provide range measurements against aircraft as an aid to aiming their anti-aircraft artillery. Both operated at the longer wavelengths typical of the RAF radars of the era, which led to them being relatively large. The teams had made considerable progress on both projects by the summer of 1937, with Gun Laying radar, Mk. I (GL) about to enter initial production, and the MRUs later taken over in 1938 by the RAF as the AMES Type 9. [6]
With this work starting to move from development to production, coincident with Bowen's astonishing anti-shipping demonstration, Butement began looking for ways to adapt Bowen's 1.5 m set for new roles. They revisited their original concept to develop Coast Defence radar (CD), allowing the Army's coastal artillery to aim their guns at night or in fog. The CD set was in most respects a version of the GL working at the shorter 1.5 m wavelength, and like GL, used separate transmit and receive antennas that had to be rotated together to be aimed at a target. The earlier GL system operated at just over 6 m, which meant the antenna was very large. The GL array had only four horizontal elements in it, which offered resolution on the order of 20 degrees. This allowed the operator to pick out a single aircraft as long as they weren't in formation, but could not be used to directly guide the guns. In contrast, the 1.5 m wavelength of the new sets allowed an antenna of about the same size to feature eight dipoles, reducing the angle to about 1.5 degrees.
Although this was of marginal capability in terms of directly aiming the guns, in July 1939 it was noticed that when the Army's 9.2-inch guns missed their targets, the splash of water caused by the shell would cause a brief but obvious return on the radar sets. This meant that any inaccuracy in the radar antenna's measurements could be eliminated by comparing the target and the splashes on the screen, as these would both have exactly the same error. The gunners could then correct their fire ("walk") onto the targets in the same fashion that they would when being given corrections by remote observers. [6]
During early tests against Chain Home in 1938, RAF pilots had noticed they could escape detection by flying at low altitudes. This was due to the minimum angle of the CH being about 1.5 degrees above the horizon, which meant aircraft were below the radar's sight until they approached within a few miles. They could escape detection entirely by flying between two CH stations at altitudes around 1,500 feet (460 m). At first this was not considered to be a serious limitation, as bombers typically flew at altitudes of 15,000 feet or greater, and at that altitude they could be detected over France.
But as the magnitude of the problem became clear, Watt became concerned. In July 1939 he placed an order for twenty-four CD sets under the name AMES Type 2 (Type 1 being Chain Home), intending to place one at each Chain Home station to allow coverage at lower altitudes, [7] as low as 500 feet (150 m). [6] These differed from the CD sets primarily in the antenna: instead of a single horizontal array, CHL used four stacked arrays of five dipoles, reducing the azimuth accuracy but allowing altitude to be estimated by comparing the returns from the different sets of vertical arrays. In keeping with its rapid introduction, CHL was a relatively simple manually-directed system that required the operator to hunt for targets by swinging the antenna back and forth looking for returns. The antenna was originally powered by WAAFs mounted on wheel-less bicycles whose chains were connected to a gear system.
It was not long after the start of the war that the Germans accidentally noticed the effect when flying low. In this case, aircraft sent on minelaying sorties almost always returned while those on other intruder missions were almost always intercepted. These aircraft had to drop their payloads from very low altitudes, so they generally followed routes over water, including rivers, flying at low altitudes for most of the mission. At first, it was not obvious why they were surviving, as there could be many reasons; fighters might not be able to see them against the ground, AA guns positioned inland might not be able to aim at them, etc. But it quickly became apparent that low altitude flight meant they were not being detected on the radars.
The Luftwaffe soon began a series of low-level attacks that proved almost impossible to defend against. Additional CHL sets were ordered and set up to fill the gaps between the sets co-located at the CH stations. In April 1941 all of the CHL sets were upgraded with a new antenna that was motorized to spin at 1, 1.5, 2 or 3.33 rpm, and used a single transmit/receive antenna instead of separate ones.
When first deployed, CHL was used both for early detection of low-level targets, as well as a system for tracking individual aircraft over land; unlike CH which was permanently facing over water, CHL could be turned to look in any direction. This latter role became outdated with the introduction of the AMES Type 7 in 1942. Electronically, the Type 7 was essentially a larger and more powerful version of the CHL, with a larger ground-level antenna. However, the antenna was continuously spun through a complete circle, and returns were plotted in a map-like form known as a plan-position indicator (PPI). Whereas CHL operators had to calculate a single target's position from the range and bearing, Type 7 operators saw all of the aircraft in their area simultaneously and could determine their map location directly. CHL was increasingly used purely for early warning, calling in the rough location of targets to Type 7 stations who would then know where to look. Later, 3 GHz-frequency Chain Home Extra Low (CHEL) radar were often co-sited with CHL sites, further extending detection as low as 50 feet (15 m).
Several adaptations of the CHL were made during the war. Such systems could be mobile [8] in which units were placed on trucks for movement matching the enemy's, extending the RAF's options in engaging the enemy.
Although GCI began to supplant CHL during 1941 and especially 1942, CHL continued to provide an important early warning role. In February 1942 the Germans mounted the Channel Dash, moving two of their battleships to harbours in Germany by sailing them right up the English Channel. This major embarrassment was due largely to supremely effective jamming on the part of the Germans, who managed to render the CH and CHL radars covering the coast entirely ineffective without the operators even noticing.[ citation needed ]
To address this, the RAF began development of the AMES Type 11, a truck-mounted CHL system operating at 500–600 MHz. This frequency was chosen to match that of German anti-aircraft radars, in the hopes that the signals would be more difficult to notice, and that jamming would have negative effects on the German's own radars. Type 11's were deliberately used only in times of jamming in order to avoid giving the Germans signals intelligence about them, and in the end were little used. [9]
Radar is a system that uses radio waves to determine the distance (ranging), direction, and radial velocity of objects relative to the site. It is a radiodetermination method used to detect and track aircraft, ships, spacecraft, guided missiles, motor vehicles, map weather formations, and terrain.
Identification, friend or foe (IFF) is a combat identification system designed for command and control. It uses a transponder that listens for an interrogation signal and then sends a response that identifies the broadcaster. IFF systems usually use radar frequencies, but other electromagnetic frequencies, radio or infrared, may be used. It enables military and civilian air traffic control interrogation systems to identify aircraft, vehicles or forces as friendly, as opposed to neutral or hostile, and to determine their bearing and range from the interrogator. IFF is used by both military and civilian aircraft. IFF was first developed during World War II, with the arrival of radar, and several friendly fire incidents.
Chain Home, or CH for short, was the codename for the ring of coastal early warning radar stations built by the Royal Air Force (RAF) before and during the Second World War to detect and track aircraft. Initially known as RDF, and given the official name Air Ministry Experimental Station Type 1 in 1940, the radar units were also known as Chain Home for most of their life. Chain Home was the first early warning radar network in the world and the first military radar system to reach operational status. Its effect on the war made it one of the most powerful systems of what became known as the "Wizard War".
AMES, short Air Ministry Experimental Station, was the name given to the British Air Ministry's radar development team at Bawdsey Manor in the immediate pre-World War II era. The team was forced to move on three occasions, changing names as part of these moves, so the AMES name applies only to the period between 1936 and 1939.
Royal Air Force Ventnor or more simply RAF Ventnor is a former Royal Air Force radar station located 0.7 miles (1.1 km) north east of Ventnor on the Isle of Wight, England. It was initially constructed in 1937 as part of a World War II coastal defence programme codenamed Chain Home. The site played an important role during the Second World War, providing early warnings of incoming bomber attacks carried out by the Luftwaffe.
William Alan Stewart Butement was a New Zealand-born British-Australian defence scientist and public servant. A native of New Zealand, he made extensive contributions to radar development in Great Britain during World War II, served as the first chief scientist for the Australian Defence Scientific Service, then ended his professional career with a research position in private business.
Radar in World War II greatly influenced many important aspects of the conflict. This revolutionary new technology of radio-based detection and tracking was used by both the Allies and Axis powers in World War II, which had evolved independently in a number of nations during the mid 1930s. At the outbreak of war in September 1939, both the United Kingdom and Germany had functioning radar systems. In the UK, it was called RDF, Range and Direction Finding, while in Germany the name Funkmeß (radio-measuring) was used, with apparatuses called Funkmessgerät . By the time of the Battle of Britain in mid-1940, the Royal Air Force (RAF) had fully integrated RDF as part of the national air defence.
Radar, Aircraft Interception, Mark IV, produced by the USA as SCR-540, was the world's first operational air-to-air radar system. Early Mk. III units appeared in July 1940 on converted Bristol Blenheim light bombers, while the definitive Mk. IV reached widespread availability on the Bristol Beaufighter heavy fighter by early 1941. On the Beaufighter, the Mk. IV arguably played a role in ending the Blitz, the Luftwaffe's night bombing campaign of late 1940 and early 1941.
Radar, Aircraft Interception, Mark VIII, or AI Mk. VIII for short, was the first operational microwave-frequency air-to-air radar. It was used by Royal Air Force night fighters from late 1941 until the end of World War II. The basic concept, using a moving parabolic antenna to search for targets and track them accurately, remained in use by most airborne radars well into the 1980s.
Aircraft interception radar, or AI radar for short, is a British term for radar systems used to equip aircraft with the means to find and track other flying aircraft. These radars are used primarily by Royal Air Force (RAF) and Fleet Air Arm night fighters and interceptors for locating and tracking other aircraft, although most AI radars could also be used in a number of secondary roles as well. The term was sometimes used generically for similar radars used in other countries, notably the US. AI radar stands in contrast with ASV radar, whose goal is to detect ships and other sea-suface vessels, rather than aircraft; both AI and ASV are often designed for airborne use.
Radar, Gun Laying, Mark I, or GL Mk. I for short, was an early radar system developed by the British Army to provide range information to associated anti-aircraft artillery. There were two upgrades to the same basic system, GL/EF and GL Mk. II, both of which added the ability to accurately determine bearing and elevation.
IFF Mark II was the first operational identification friend or foe system. It was developed by the Royal Air Force just before the start of World War II. After a short run of prototype Mark Is, used experimentally in 1939, the Mark II began widespread deployment at the end of the Battle of Britain in late 1940. It remained in use until 1943, when it began to be replaced by the standardised IFF Mark III, which was used by all Allied aircraft until long after the war ended.
Searchlight Control, SLC for short but nicknamed "Elsie", was a British Army VHF-band radar system that provided aiming guidance to an attached searchlight. By combining a searchlight with a radar, the radar did not have to be particularly accurate, it only had to be good enough to get the searchlight beam on the target. Once the target was lit, normal optical instruments could be used to guide the associated anti-aircraft artillery. This allowed the radar to be much smaller, simpler and less expensive than a system with enough accuracy to directly aim the guns, like the large and complex GL Mk. II radar. In 1943 the system was officially designated Radar, AA, No. 2, although this name is rarely used.
The AMES Type 82, also widely known by its rainbow codename Orange Yeoman, was an S-band 3D radar built by the Marconi Company and used by the Royal Air Force (RAF), initially for tactical control and later for air traffic control (ATC).
The AMES Type 80, sometimes known by its development rainbow code Green Garlic, was a powerful early warning (EW) and ground-controlled interception (GCI) radar developed by the Telecommunications Research Establishment (TRE) and built by Decca for the Royal Air Force (RAF). It could reliably detect a large fighter or small bomber at ranges over 210 nautical miles, and large, high-flying aircraft were seen out to the radar horizon. It was the primary military ground-based radar in the UK from the mid-1950s into the late 1960s, providing coverage over the entire British Isles.
Radar, Air to Surface Vessel, Mark II, or ASV Mk. II for short, was an airborne sea-surface search radar developed by the UK's Air Ministry immediately prior to the start of World War II. It was the first aircraft-mounted radar of any sort to be used operationally. It was widely used by aircraft of the RAF Coastal Command, Fleet Air Arm and similar groups in the United States and Canada. A version was also developed for small ships, the Royal Navy's Type 286.
The AMES Type 7, also known as the Final GCI, was a ground-based radar system introduced during World War II by the Royal Air Force (RAF). The Type 7 was the first truly modern radar used by the Allies, providing a 360 degree view of the airspace around the station out to a distance of about 90 miles (140 km). It allowed fighter interceptions to be plotted directly from the radar display, a concept known as ground controlled intercept, or GCI.
The AMES Type 84, also known as the Microwave Early Warning or MEW, was a 23 cm wavelength early warning radar used by the Royal Air Force (RAF) as part of the Linesman/Mediator radar network. Operating in the L-band gave it improved performance in rain and hail, where the primary AMES Type 85 radar's performance dropped off. It operated beside the Type 85 and RX12874 in Linesman, and moved to the UKADGE system in the 1980s before being replaced during UKADGE upgrades in the early 1990s.
Bent Rigg Radar Station,, was a radar site located at Bent Rigg, 0.6 miles (1 km) south of Ravenscar, North Yorkshire, England. Several radar stations had been located in the Ravenscar area from 1938, but a more permanent site was built at Bent Rigg in 1941, which was crewed by technicians and other staff from the Royal Air Force. Bent Rigg, and the wider location around Ravenscar, was deemed "attractive" for the siting of long-range finding equipment. It was originally part of the Coastal Defence/Chain Home Low (CD/CHL) system, designed to detect shipping. Later, it was upgraded with more powerful equipment as part of the Chain Home Extra Low (CHEL). The last recorded use of the station was in September 1944, and it is believed that the site closed soon afterwards.
AMES Type 6, also known as the Light Warning Set or L/W, was a portable early warning radar developed by the Air Ministry Experimental Station (AMES) for use by the Royal Air Force (RAF) in the field. Units in British Army service were officially known as Radar, Anti-Aircraft, Number 4, or AA. No. 4 for short, although this name was rarely used in practice. The system was also built in Canada for use by the US Army, who referred to them as SCR-602-A.
{{cite book}}
: CS1 maint: location missing publisher (link)