Motorboating (electronics)

Last updated April 24, 2023

In electronics, motorboating is a type of low frequency parasitic oscillation (unwanted cyclic variation of the output voltage) that sometimes occurs in audio and radio equipment and often manifests itself as a sound similar to an idling motorboat engine, a "put-put-put", in audio output from speakers or earphones.^[1]^[2]^[3]^[4] It is a problem encountered particularly in radio transceivers and older vacuum tube audio systems, guitar amplifiers, PA systems and is caused by some type of unwanted feedback in the circuit. The amplifying devices in audio and radio equipment are vulnerable to a variety of feedback problems, which can cause distinctive noise in the output. The term motorboating is applied to oscillations whose frequency is below the range of hearing, from 1 to 10 hertz,^[3] so the individual oscillations are heard as pulses. Sometimes the oscillations can even be seen visually as the woofer cones in speakers slowly moving in and out.^[2]

Occurrence

Although low frequency parasitic oscillations in audio equipment may be due to a range of causes, there are a few types of equipment in which it is frequently seen:

Older audio amplifiers with capacitive (RC) or inductive (transformer) coupling between stages.^[5]^[6]^[7]^[8] This design is mostly used in vacuum tube (valve) equipment.^[8] Motorboating was a problem throughout the era of vacuum tube electronics^[5] but became rare as vacuum tube gear was replaced in the 1970s with modern solid state designs, which are direct-coupled.^[8] The recent resurgence in popularity of traditional tube-type audio equipment in guitar amplifiers and home audio systems has led to a reappearance of motorboating problems. The problem is sometimes caused in older equipment by the evaporation of the electrolyte from old-style "wet" electrolytic capacitors used in the power circuits of legacy equipment, or in equipment of any age where an amplifier stage is sensitive to feedback via power supply rails, and can be remedied by replacing/upgrading the capacitors.
In both old and new designs, even mostly directly-coupled operational amplifier circuits, feedback through the power supply rails can generate ultrasonic oscillations that vary in amplitude at a low frequency (squegging) due to the power supply voltage sagging as oscillations build up (the long time constant coming from the power supply reservoir capacitor) in such a way that the low frequency is audible even though the high frequency fundamental is not. Such problems can be difficult to diagnose.^[9]^[10]
Audio equipment associated with radio transmitters, particularly transceivers in two way radios, such as Citizens band, FRS, which have automatic gain control (AGC) or squelch noise control. Malfunctions in the AGC or squelch circuits, which have long time constants, can cause low frequency oscillation. Another possible cause, sometimes in combination with the first, is leakage of the strong radio frequency (RF) signal from the transmitter into the receiver audio sections, which can cause quenching oscillations. This is a RFI problem, caused by inadequate shielding or filtering to keep the RF out.

Theory

As with all electronic oscillation, motorboating occurs when some of the output energy from an amplifying device like a transistor or vacuum tube gets coupled back into the input circuit of the device (or possibly into an earlier stage of the amplifier circuit) with the proper phase for positive feedback. This indicates there is an unwanted feedback path through the circuit from output to input of an amplifying stage. The technical conditions for oscillation, given by the Barkhausen stability criterion, are that the total gain around the feedback loop (comprising the amplifying device and the feedback path) at the oscillation frequency must be one (0 dB), and that the phase shift must be a multiple of 360° (2π radians). Since most amplifying devices, transistors and tubes, are inverting, with the output signal 180° opposite in phase from the input, the feedback path must contribute the other 180° of shift.

Many types of parasitic oscillation are caused by small interelectrode capacitances (parasitic capacitance) or mutual inductance between adjacent wires or electronic components on the circuit board, which create an inadvertent feedback path. However these usually cause oscillations of high frequency, at the upper end of or above the passband of the equipment. This is because the phase shift of the small reactances in the feedback path, which increases with frequency, only become significant at high frequencies. Low frequency oscillations like motorboating indicate that some device or circuit with a large time constant is involved, such as the interstage coupling capacitors^[6] or transformers, or the filter capacitors and supply transformer winding.^[6]

In vacuum tube circuits, a common cause is feedback through the plate power supply circuit.^[2]^[6]^[4] The power supply provides DC current to each tube's plate circuit, so the power supply wiring (power busses) can be an inadvertent feedback path between stages. The increasing impedance of the filter capacitors at low frequencies can mean that low frequency swings in the current drawn by output stages can cause voltage swings in the power supply voltage which feed back to earlier stages,^[2]^[6]^[4] making the system a subaudio oscillator. This is caused by inadequate power supply filtering or decoupling. The electrolytic capacitors used in equipment of 1960s vintage contained liquid electrolyte, which dried out over decades, decreasing the capacitance and increasing the leakage current, and these are often the cause.

One solution suggested is a "capacitor job", replacing all the old electrolytic capacitors.^[4]^[11] A more radical but comprehensive solution is to add modern IC voltage regulators, or replace the entire power supply with a modern regulated one.^[4]

In radio equipment

In equipment that includes radio transmitters, motorboating can be caused by radio frequency interference (RFI), the strong radio signal from the transmitter getting into audio or receiver circuits. Receiver audio circuits with automatic gain control (AGC) have a long time constant feedback loop which adjusts the gain of the audio stage to compensate for differences in audio level from causes like different speaking voices. Squelch circuits used in two-way radios to cut out noise similarly have a feedback loop which turns off the audio when high frequency noise is detected.

If the inaudible radio frequency (RF) transmitter signal is inadvertently coupled into the receiver's audio signal path, it can trigger the AGC or squelch circuit to reduce the gain. Then, after a delay time set by the circuit's time constant, the circuit increases the gain again until the amplitude of the radio signal triggers another gain reduction. This repetitive cycle is heard as motorboating.

An example might be a 27 MHz Citizen's band radio in a car, connected to the car's 12 volt DC supply. If the decoupling capacitors which bypass radio noise from the power supply wires are missing or inadequate, or the long power leads pick up excessive RF from the antenna then it is possible for the RF transmitter signal to enter the radio's receiving circuits through the supply wires. This then causes the motorboating to occur.

Related Research Articles

<span class="mw-page-title-main">Amplitude modulation</span> Radio modulation via wave amplitude

Amplitude modulation (AM) is a modulation technique used in electronic communication, most commonly for transmitting messages with a radio wave. In amplitude modulation, the amplitude of the wave is varied in proportion to that of the message signal, such as an audio signal. This technique contrasts with angle modulation, in which either the frequency of the carrier wave is varied, as in frequency modulation, or its phase, as in phase modulation.

<span class="mw-page-title-main">Electronic oscillator</span> Type of electronic circuit

An electronic oscillator is an electronic circuit that produces a periodic, oscillating electronic signal, often a sine wave or a square wave or a triangle wave. Oscillators convert direct current (DC) from a power supply to an alternating current (AC) signal. They are widely used in many electronic devices ranging from simplest clock generators to digital instruments and complex computers and peripherals etc. Common examples of signals generated by oscillators include signals broadcast by radio and television transmitters, clock signals that regulate computers and quartz clocks, and the sounds produced by electronic beepers and video games.

An amplifier, electronic amplifier or (informally) amp is an electronic device that can increase the power of a signal. It is a two-port electronic circuit that uses electric power from a power supply to increase the amplitude of a signal applied to its input terminals, producing a proportionally greater amplitude signal at its output. The amount of amplification provided by an amplifier is measured by its gain: the ratio of output voltage, current, or power to input. An amplifier is a circuit that has a power gain greater than one.

A tetrode is a vacuum tube having four active electrodes. The four electrodes in order from the centre are: a thermionic cathode, first and second grids and a plate. There are several varieties of tetrodes, the most common being the screen-grid tube and the beam tetrode. In screen-grid tubes and beam tetrodes, the first grid is the control grid and the second grid is the screen grid. In other tetrodes one of the grids is a control grid, while the other may have a variety of functions.

A valve amplifier or tube amplifier is a type of electronic amplifier that uses vacuum tubes to increase the amplitude or power of a signal. Low to medium power valve amplifiers for frequencies below the microwaves were largely replaced by solid state amplifiers in the 1960s and 1970s. Valve amplifiers can be used for applications such as guitar amplifiers, satellite transponders such as DirecTV and GPS, high quality stereo amplifiers, military applications and very high power radio and UHF television transmitters.

A regenerative circuit is an amplifier circuit that employs positive feedback. Some of the output of the amplifying device is applied back to its input so as to add to the input signal, increasing the amplification. One example is the Schmitt trigger, but the most common use of the term is in RF amplifiers, and especially regenerative receivers, to greatly increase the gain of a single amplifier stage.

A tuned radio frequency receiver is a type of radio receiver that is composed of one or more tuned radio frequency (RF) amplifier stages followed by a detector (demodulator) circuit to extract the audio signal and usually an audio frequency amplifier. This type of receiver was popular in the 1920s. Early examples could be tedious to operate because when tuning in a station each stage had to be individually adjusted to the station's frequency, but later models had ganged tuning, the tuning mechanisms of all stages being linked together, and operated by just one control knob. By the mid 1930s, it was replaced by the superheterodyne receiver patented by Edwin Armstrong.

In radio communications, a radio receiver, also known as a receiver, a wireless, or simply a radio, is an electronic device that receives radio waves and converts the information carried by them to a usable form. It is used with an antenna. The antenna intercepts radio waves and converts them to tiny alternating currents which are applied to the receiver, and the receiver extracts the desired information. The receiver uses electronic filters to separate the desired radio frequency signal from all the other signals picked up by the antenna, an electronic amplifier to increase the power of the signal for further processing, and finally recovers the desired information through demodulation.

The Armstrong oscillator is an electronic oscillator circuit which uses an inductor and capacitor to generate an oscillation. It is the earliest oscillator circuit, invented by US engineer Edwin Armstrong in 1912 and independently by Austrian engineer Alexander Meissner in 1913, and was used in the first vacuum tube radio transmitters. It is sometimes called a tickler oscillator because its distinguishing feature is that the feedback signal needed to produce oscillations is magnetically coupled into the tank inductor in the input circuit by a "tickler coil" (L2, right) in the output circuit. Assuming the coupling is weak but sufficient to sustain oscillation, the oscillation frequency f is determined primarily by the LC circuit and is approximately given by

Linear electronic oscillator circuits, which generate a sinusoidal output signal, are composed of an amplifier and a frequency selective element, a filter. A linear oscillator circuit which uses an RC network, a combination of resistors and capacitors, for its frequency selective part is called an RC oscillator.

A class-D amplifier or switching amplifier is an electronic amplifier in which the amplifying devices operate as electronic switches, and not as linear gain devices as in other amplifiers. They operate by rapidly switching back and forth between the supply rails, using pulse-width modulation, pulse-density modulation, or related techniques to produce a pulse train output. This passes through a simple low-pass filter which blocks the high-frequency pulses and provides analog output current and voltage. Because they are always either in fully on or fully off modes, little energy is dissipated in the transistors and efficiency can exceed 90%.

A pentode is an electronic device having five electrodes. The term most commonly applies to a three-grid amplifying vacuum tube or thermionic valve that was invented by Gilles Holst and Bernhard D.H. Tellegen in 1926. The pentode was developed from the screen-grid tube or shield-grid tube by the addition of a grid between the screen grid and the plate. The screen-grid tube was limited in performance as an amplifier due to secondary emission of electrons from the plate. The additional grid is called the suppressor grid. The suppressor grid is usually operated at or near the potential of the cathode and prevents secondary emission electrons from the plate from reaching the screen grid. The addition of the suppressor grid permits much greater output signal amplitude to be obtained from the plate of the pentode in amplifier operation than from the plate of the screen-grid tube at the same plate supply voltage. Pentodes were widely manufactured and used in electronic equipment until the 1960s to 1970s, during which time transistors replaced tubes in new designs. During the first quarter of the 21st century, a few pentode tubes have been in production for high power radio frequency applications, musical instrument amplifiers, home audio and niche markets.

<span class="mw-page-title-main">Linear amplifier</span> Electronic circuit

A linear amplifier is an electronic circuit whose output is proportional to its input, but capable of delivering more power into a load. The term usually refers to a type of radio-frequency (RF) power amplifier, some of which have output power measured in kilowatts, and are used in amateur radio. Other types of linear amplifier are used in audio and laboratory equipment. Linearity refers to the ability of the amplifier to produce signals that are accurate copies of the input. A linear amplifier responds to different frequency components independently, and tends not to generate harmonic distortion or intermodulation distortion. No amplifier can provide perfect linearity however, because the amplifying devices—transistors or vacuum tubes—follow nonlinear transfer function and rely on circuitry techniques to reduce those effects. There are a number of amplifier classes providing various trade-offs between implementation cost, efficiency, and signal accuracy.

The Neutrodyne radio receiver, invented in 1922 by Louis Hazeltine, was a particular type of tuned radio frequency (TRF) receiver, in which the instability-causing inter-electrode capacitance of the triode RF tubes is cancelled out or "neutralized" to prevent parasitic oscillations which caused "squealing" or "howling" noises in the speakers of early radio sets. In most designs, a small extra winding on each of the RF amplifiers' tuned anode coils was used to generate a small antiphase signal, which could be adjusted by special variable trim capacitors to cancel out the stray signal coupled to the grid via plate-to-grid capacitance. The Neutrodyne circuit was popular in radio receivers until the 1930s, when it was superseded by the superheterodyne receiver.

Clipping is a form of waveform distortion that occurs when an amplifier is overdriven and attempts to deliver an output voltage or current beyond its maximum capability. Driving an amplifier into clipping may cause it to output power in excess of its power rating.

In electronics, a choke is an inductor used to block higher-frequency alternating currents (ACs) while passing direct current (DC) and lower-frequency ACs in a circuit. A choke usually consists of a coil of insulated wire often wound on a magnetic core, although some consist of a doughnut-shaped "bead" of ferrite material strung on a wire. The choke's impedance increases with frequency. Its low electrical resistance passes both AC and DC with little power loss, but its reactance limits the amount of AC passed.

A radio transmitter or just transmitter is an electronic device which produces radio waves with an antenna. Radio waves are electromagnetic waves with frequencies between about 30 Hz and 300 GHz. The transmitter itself generates a radio frequency alternating current, which is applied to the antenna. When excited by this alternating current, the antenna radiates radio waves. Transmitters are necessary parts of all systems that use radio: radio and television broadcasting, cell phones, wireless networks, radar, two way radios like walkie talkies, radio navigation systems like GPS, remote entry systems, among numerous other uses.

<span class="mw-page-title-main">Reflex receiver</span>

A reflex radio receiver, occasionally called a reflectional receiver, is a radio receiver design in which the same amplifier is used to amplify the high-frequency radio signal (RF) and low-frequency audio (sound) signal (AF). It was first invented in 1914 by German scientists Wilhelm Schloemilch and Otto von Bronk, and rediscovered and extended to multiple tubes in 1917 by Marius Latour and William H. Priess. The radio signal from the antenna and tuned circuit passes through an amplifier, is demodulated in a detector which extracts the audio signal from the radio carrier, and the resulting audio signal passes again through the same amplifier for audio amplification before being applied to the earphone or loudspeaker. The reason for using the amplifier for "double duty" was to reduce the number of active devices, vacuum tubes or transistors, required in the circuit, to reduce the cost. The economical reflex circuit was used in inexpensive vacuum tube radios in the 1920s, and was revived again in simple portable tube radios in the 1930s.

A valve RF amplifier or tube amplifier (U.S.) is a device for electrically amplifying the power of an electrical radio frequency signal.

Parasitic oscillation is an undesirable electronic oscillation in an electronic or digital device. It is often caused by feedback in an amplifying device. The problem occurs notably in RF, audio, and other electronic amplifiers as well as in digital signal processing. It is one of the fundamental issues addressed by control theory.

References

↑ Amos, S. W.; Roger Amos (2002). Newnes Dictionary of Electronics, 4th Ed. Newnes. p. 205. ISBN 0080524052.
1 2 3 4 Van der Veen, Menno (1999). Modern High-end Valve Amplifiers: Based on Toroidal Output Transformers. Elektor International Media. p. 15. ISBN 0905705637.
1 2 Dailey, Denton J. (2013). Electronics for Guitarists, 2nd Ed. Springer. p. 163. ISBN 978-1461440871.
1 2 3 4 5 Jones, Morgan (2011). Valve Amplifiers, 4th Ed. Elsevier. p. 467. ISBN 978-0080966403.
1 2 The problem was common in the early days of radio: Westcott, O. D. (August 1927). ""Motorboating" - What it is, and why" (PDF). Radio News. Experimenter Publishing Co.: 149. Retrieved July 7, 2013.
1 2 3 4 5 Bouck, Zeh (March 1927). "Motorboating Cured" (PDF). Radio Engineering. New York: Radio Engineering Publishing Co. 7 (3): 614–615. Retrieved January 9, 2015.
↑ Duncan, Ben (1996). High Performance Audio Power Amplifiers . Newnes. pp. 191. ISBN 0080508049. motorboating.
1 2 3 Self, Douglas (2012). Audio Power Amplifier Design Handbook, 4th Ed. CRC Press. p. 7.42. ISBN 978-1136123733.
↑ Help Troubleshooting Old Transmitter
↑ EL34 PP motorboating questions
↑ Keen, R. G. (1997). "Motorboating". Tube Amplifier Debugging Page . GEO Guitar Effects Oriented web page. Retrieved July 3, 2013.{{cite web}}: External link in |work= (help)

This page is based on this Wikipedia article
Text is available under the CC BY-SA 4.0 license; additional terms may apply.
Images, videos and audio are available under their respective licenses.

[Amos-1] Amos, S. W.; Roger Amos (2002). Newnes Dictionary of Electronics, 4th Ed. Newnes. p. 205. ISBN 0080524052.

[Van_der_Veen-2] 1 2 3 4 Van der Veen, Menno (1999). Modern High-end Valve Amplifiers: Based on Toroidal Output Transformers. Elektor International Media. p. 15. ISBN 0905705637.

[Dailey-3] 1 2 Dailey, Denton J. (2013). Electronics for Guitarists, 2nd Ed. Springer. p. 163. ISBN 978-1461440871.

[Jones-4] 1 2 3 4 5 Jones, Morgan (2011). Valve Amplifiers, 4th Ed. Elsevier. p. 467. ISBN 978-0080966403.

[Westcott-5] 1 2 The problem was common in the early days of radio: Westcott, O. D. (August 1927). ""Motorboating" - What it is, and why" (PDF). Radio News. Experimenter Publishing Co.: 149. Retrieved July 7, 2013.

[Bouck-6] 1 2 3 4 5 Bouck, Zeh (March 1927). "Motorboating Cured" (PDF). Radio Engineering. New York: Radio Engineering Publishing Co. 7 (3): 614–615. Retrieved January 9, 2015.

[Duncan-7] Duncan, Ben (1996). High Performance Audio Power Amplifiers . Newnes. pp. 191. ISBN 0080508049. motorboating.

[Self-8] 1 2 3 Self, Douglas (2012). Audio Power Amplifier Design Handbook, 4th Ed. CRC Press. p. 7.42. ISBN 978-1136123733.

[9] Help Troubleshooting Old Transmitter

[10] EL34 PP motorboating questions

[Keen-11] Keen, R. G. (1997). "Motorboating". Tube Amplifier Debugging Page . GEO Guitar Effects Oriented web page. Retrieved July 3, 2013.{{cite web}}: External link in |work= (help)

[1]

[2]

[3]

[4]

[5]

[6]

[7]

[8]

[9]

[10]

[11]