PC/104

Last updated
A PCI-104 single-board computer PCI-104 EP405.JPG
A PCI-104 single-board computer

PC/104 (or PC104) is a family of embedded computer standards which define both form factors and computer buses by the PC/104 Consortium. Its name derives from the 104 pins on the interboard connector (ISA) in the original PC/104 specification [1] [2] and has been retained in subsequent revisions, despite changes to connectors. PC/104 is intended for specialized environments where a small, rugged computer system is required. The standard is modular, and allows consumers to stack together boards from a variety of COTS manufacturers to produce a customized embedded system. [3]

Contents

The original PC/104 form factor is somewhat smaller than a desktop PC motherboard at 3.550 × 3.775 inches (90 × 96 mm). Unlike other popular computer form factors such as ATX, which rely on a motherboard or backplane, PC/104 boards are stacked on top of each other like building blocks. The PC/104 specification defines four mounting holes at the corners of each module, which allow the boards to be fastened to each other using standoffs. The stackable bus connectors and use of standoffs provides a more rugged mounting than slot boards found in desktop PCs. The compact board size further contributes to the ruggedness of the form factor by reducing the possibility of PCB flexing under shock and vibration.

A typical PC/104 system (commonly referred to as a "stack") will include a CPU board, power supply board, and one or more peripheral boards, such as a data acquisition module, GPS receiver, or Wireless LAN controller. A wide array of peripheral boards are available from various vendors. Users may design a stack that incorporates boards from multiple vendors. The overall height, weight, and power consumption of the stack can vary depending on the number of boards that are used.

PC/104 is sometimes referred to as a "stackable PC", as most of the architecture derives from the desktop PC. [4] The majority of PC/104 CPU boards are x86 compatible and include standard PC interfaces such as Serial Ports, USB, Ethernet, and VGA. A x86 PC/104 system is usually capable of standard PC operating system such as DOS, Windows, or Linux. However, it is also quite common to use a real-time operating system, such as VxWorks.

History and standardization

The PC/104 bus and form factor was originally devised by Ampro in 1987 (led by CTO Rick Lehrbaum), [5] and later standardized by the PC/104 Consortium in 1992. [6] An IEEE standard corresponding to PC/104 was drafted as IEEE P996.1, but never ratified. [7] In 1997, the PC/104 Consortium introduced a newer standard based on the PCI bus. [8] A PCI Express-based standard was introduced in 2008. [9]

PC/104-related specifications are controlled by the PC/104 Consortium. There are currently 47 members of the Consortium. [10] All specifications published by the Consortium are freely available. Membership in the Consortium is not required to design and manufacture a PC/104 board.

SpecificationInitial ReleaseBus CommunicationCurrent Version
PC/1041992 ISA (AT and XT)2.6
PC/104-Plus1997 ISA and PCI
PCI-1042003 PCI 1.1
PCI/104-Express and PCIe/1042008PCI and PCI Express 3.0 [11]

Bus structure vis-à-vis form factor

The specifications released by the PC/104 Consortium define multiple of Bus Structures (ISA, PCI, PCI Express) and Form Factors (104, EBX, EPIC). Bus Structure defines the location and pinout of the bus connector(s). Form Factor refers to size and shape of the board. It is possible to find one of the PC/104 stackable expansion buses on a number of different form factors. While most commercially available products using the Bus Structures will comply with the Form Factors listed below, it is possible for a non-standard or proprietary form factor to incorporate one of the PC/104 Bus Structures for expandability.

Note the term "PC/104" is often used interchangeably to refer to either the Bus Structure or Form Factor. This can be a source of confusion. For example, a product datasheet may refer to a board as "PC/104" due to its size and shape when it in fact has a PCI-104 expansion bus.

Bus structures

The PC/104 Consortium specifications define a variety a computer buses, all of which derive from the ISA, PCI, and PCI Express buses found in a desktop PC.

PC/104

The original PC/104 bus derives from the ISA bus. It includes all the signals found on the ISA bus, with additional ground pins added to ensure bus integrity. Signal timing and voltage levels are identical to the ISA bus, with lower current requirements. The PC/104 specification defines two versions of the bus, 8-bit or 16-bit. The 8-bit version corresponds to the IBM XT and consists of 64 pins. The 16-bit version corresponds to the IBM AT and adds 40 additional pins, bringing the total to 104 (hence the name "PC/104"). The signals marked J1/P1 are only found on the 8-bit version, while the 16-bit version adds the signals of J2/P2.

Since PC/104 is based on the ISA bus, it is often necessary to set the base address, IRQ, and DMA channel when installing a peripheral board. This is usually accomplished via the use of jumpers or DIP switches on the peripheral board. Failure to configure the peripheral correctly can cause a resource conflict and lead to erratic behavior.

PC/104-Plus

The PC/104-Plus standard adds support for the PCI bus, in addition to the ISA bus of the PC/104 standard. The name is derived from its origin: a PC/104-Plus module has a PC/104 connector (ISA) plus a PCI connector. The standard defines a 120-pin connector for the PCI bus, located on the opposite side of the board from the PC/104 connector.

PC/104-Plus CPU boards provide active communication on both buses, and are capable of communicating with both ISA and PCI peripheral cards. On PC/104-Plus peripheral modules, the PC/104 connector is simply a passive connector for stackability; the module actively communicates on the PCI bus only. As a corollary, a PC/104-Plus peripheral module may not be used with a PC/104 CPU board. However, a PC/104-Plus CPU board may be used with a PC/104 peripheral module.

Since PC/104-Plus is based on PCI, there is no need to set a Base Address, IRQ, or DMA channel on the peripheral boards. However, it is necessary to specify the PCI Slot Number of a peripheral board when it is installed. This is commonly set by a rotary switch, DIP switch, or jumpers on the peripheral board. Each PCI peripheral board in the system must have the PCI Slot Number set to a unique value. Failure to do so may cause erratic system behavior. The peripheral closest to the CPU should be set for the first slot, the next board should be set for the second slot, etc.

PCI-104

The PCI-104 form factor includes the PCI connector, but not the PC/104 connector, in order to increase the available board real estate. Even though the PCI connector has 120 pins instead of 104, the established name was kept. The PCI connector location and pinout is identical to PC/104-Plus.

Since the ISA bus is omitted, a PCI-104 board is incompatible with PC/104 peripheral module. However, PCI-104 and PC/104-Plus are compatible, since they both utilize the PCI bus. Most PC/104-Plus boards can be manufactured as PCI-104 by simply not populating the PC/104 connector.

PCI-104 utilizes the same PCI Slot Number selection scheme as PC/104-Plus. Each device must be assigned to a unique slot number.

PCI/104-Express

The PCI/104-Express specification incorporates the PCI Express bus (PCIe) in addition to the previous-generation PCI bus. The specification defines a 156-pin surface mount connector for the PCI Express signals. The new connector occupies the same board location as the legacy PC/104 ISA connector. In addition to PCI Express, the specifications also defines pins on the connector for additional modern computer buses, such as USB, SATA, and LPC.

The PCI/104-Express specification currently defines two possible pinouts for the PCIe connector: [12]

  1. Type 1 offers four x1 PCI Express links, two USB 2.0 ports, and one x16 PCIe link.
  2. Type 2 offers four x1 PCI Express links, two USB 2.0 ports, two PCIe x4 links, two USB 3.0 ports, two SATA ports, and LPC.

CPU boards and peripherals may be designed as Type 1, Type 2, or Universal (which only uses the common subset of signals between the two types, PCIe x1 and/or USB 2.0). The Type 2 pinout was not introduced until Version 2.0 of the specification (released in 2011). PCI/104-Express products introduced prior to 2011 will be either Type 1 or Universal, but may not be explicitly labeled as such. A Type 1 bus is incompatible with Type 2 peripherals, or vice versa. The specification requires the system to remain in reset and not boot in the case of a Type mismatch (no physical damage will occur). Universal peripheral boards may be used with either Type 1 or Type 2 pinouts.

Because the PCIe bus connector is surface-mount, not through-hole, it is also possible for a board to use different bus pinouts on the top side of the board vs the bottom side. For example, a CPU board may have a Type 1 bottom PCIe connector and a Type 2 top PCIe connector. Such a CPU board would be compatible with Type 1 and/or Universal peripherals on the bottom, and compatible with Type 2 and/or Universal peripherals on the top.

Similar to PC/104-Plus, a PCI/104-Express CPU boards will provide active communication on both PCI and PCIe buses. A PC/104-Express CPU board may be used with PCI-104 and PC/104-Plus peripheral modules. However, a PCI/104-Express peripheral module will communicate on the PCIe bus only; the PCI connector is simply a pass-through connector for stackability. A PC/104-Express peripheral module may not be used with a PCI-104 or PC/104-Plus CPU board (unless an ISA bridge device is used).

PCI/104-Express incorporates link shifting, which eliminates the need for the PCI slot selection switches/jumpers found on PCI-104 and PC/104-Plus peripherals. Some peripheral boards re-populate the PCIe links, which allows the stack to have additional peripheral boards beyond the initial set of PCI Express links provided by CPU board. Link repopulation is not a requirement in the specification, and must be implemented on the peripheral board with a PCI Express packet switch.

PCIe/104

PCIe/104 is similar to the PCI/104-Express standard, but omits the legacy PCI bus to increase available space on the board (similar to the relationship between PC/104-Plus and PCI-104). The PCI Express connector location and pinout options the same as PCI/104-Express (both Type 1 and Type 2). Because the PCI bus connector is omitted, a PCIe/104 board is incompatible with PC/104-Plus and PCI-104 systems (unless a PCIe-to-PCI bridge device is used).

Form factors

The PC/104 Consortium's specifications cover three form factors which define the size and shape of the board. Each form factor may utilize one of the Bus Structures listed above.

104 or PC/104

The 104 Form Factor is defined to be 3.550 × 3.775 inches (90 × 96 mm), with mounting holes at all four corners of the board. The specifications also allow for a 0.5 inches (13 mm) area beyond the edge of the PCB for I/O connectors. Some PC/104 products have oversized PCBs which extended into the I/O connector area. The extended PCB "wings" is not addressed in the specification, generally does not cause mechanical issues as long as the overall PCB + I/O connector overhang is within the maximum allowable dimensions of 4.550 × 4.393 inches (116 × 112 mm).

The dimensions were originally defined in the PC/104 Specification, and as a result the form factor is still commonly referred to as "PC/104". The PCI/104-Express and PCIe/104 Specification introduced the "104" name to distinguish the form factor from the legacy PC/104 bus.

EBX and EBX Express

EBX (Embedded Board eXpandable) is a single board computer form factor, 5.75 × 8 in (146 × 203 mm). The EBX form factor applies to the CPU board, but supports PC/104 form factor peripheral boards for expansion. The original EBX specifications allowed for the PC/104, PC/104-Plus, and PCI-104 buses. EBX Express adds the PCI-104/Express and PCIe/104 buses.

EPIC and EPIC Express

EPIC (Embedded Platform for Industrial Computing) is a single-board computer form factor which, like EBX, supports PC/104 peripheral boards but is smaller than EBX at 6.5 × 4.5 in (165 × 114 mm). It allows I/O connections to be implemented as either pin headers or PC-style ("real world") connectors. The standard provides specific I/O zones to implement functions such as Ethernet, serial ports, digital and analog I/O, video, wireless, and various application-specific interfaces. EPIC Express adds PCI Express expandability.

Stacking limits

In general, every PC/104 stack will contain a CPU board, power supply board, and one or more peripheral boards. The maximum number of boards supported by a PC/104 stack will depend on which buses are used by the peripheral boards.

  1. ISA Bus - There is no strict limit to the number of ISA boards which can coexist in one system. However, there is a limited number of Base Addresses, IRQs, and DMA channels which may become a limiting factor. ISA boards may be stacked on either side of the CPU board.
  2. PCI Bus - The PC/104-Plus and PCI-104 specifications allows for four PCI "slots". This imposes a hard limit of four PCI peripheral boards per system. All PCI peripheral modules must connect consecutively on one side of the controller due to the signaling requirements of the PCI bus.
  3. PCI Express - The total number of PCI Express peripheral boards will depend on the number of PCIe links provided by the CPU board. For example, if the CPU board provides four x1 PCIe links, then a maximum of four x1 PCIe peripheral cards may be installed. If one or more of the peripheral boards provide PCIe link repopulation, additional modules may be installed. PCIe links on the upper side of the CPU board are independent from the links on the underside. Installing a PCIe peripheral under the CPU board will not consume one of the top side links. The quantity and width of PCIe links available may vary between the top and bottom connectors of the CPU board.
  4. USB and SATA - The PCI/104-Express and PCIe/104 Specification provides signals for USB and SATA, which may be used by peripheral boards in the stack. Peripheral which use USB and SATA will be limited to the number of links provided by the CPU board. USB peripherals may provide link repopulation by incorporating an onboard USB hub.

Regardless of the buses used, the maximum number of boards of a PC/104 stack may be limited due to size, weight, and power restrictions for the target application.

Mechanical interference between boards

When stacking PC/104 boards together, mechanical interference between adjacent boards is a concern.

  1. Bus Connectors - When assembling a system composed of multiple Bus Structures, it is possible for the bus connectors to interfere with components on an adjacent board. For example, if a PC/104-Plus board is stacked on top of a PC/104 board, it is possible for the pins on the underside of the PCI connector to run into components on the lower board.
  2. Out of Spec Components and Connectors - The PC/104 specifications limit the height of components and connectors that may be placed on either side of the board. A constrained height region is intended to guarantee that boards will not interfere with other neighbors stacked above or below. However, it is not uncommon to find boards which violate these constraints.
  3. Heatsinks - The standard spacing between stacked PC/104 boards is 0.600 inches (15.24 mm). Components with significant power consumption (CPUs, GPUs, FPGAs) often require a larger heatsink which does not fit within the traditional board spacing. It is not uncommon to find PC/104 CPU boards with relatively large heatsinks that do not allow for peripheral boards to be stacked above it. Later revisions of the PCI/104-Express and PCIe/104 specification introduced an optional taller 0.866 inch (22.00 mm) connector that is compatible with the traditional height connector.

The mechanical interference issues listed above can often be addressed with a Bus Spacer, which allows additional room between the boards. However, Bus Spacers increase overall stack height, and may not be suitable for space-constrained applications. It may also be possible to re-arrange the boards in the stack to remove the interference. Another option is to modify the offending boards to remove the interference (e.g. depopulate a connector), but this may require the vendor to supply a customized version of the board.

Potential compatibility issues

In theory, PC/104 boards are interoperable. It is possible to assemble a system using boards from several different vendors, subject to the fundamental Bus Structure compatibility issues listed above. However, compatibility issues sometimes appear.

Software development

The majority of PC/104 CPU boards are x86 compatible, and are capable of running commercially available off-the-shelf PC software without modification. The standard PC I/O interfaces of a PC/104 system (Serial Ports, USB, Ethernet, VGA, etc.) are typically supported via the native drivers built into the operating system. Certain peripheral boards, such as data acquisition may require special drivers from the board manufacturer.

From a software development perspective, there is little difference between compiling software for a desktop PC or compiling for an x86 PC/104 stack. Software can be developed using standard x86 compilers (e.g. Visual Studio if the PC/104 system is running Windows). There is typically no need for specialized development tools, such as cross compilers, Board Support Packages, or JTAG debuggers. This is a significant departure from non-x86 embedded system platforms, which often require a development toolchain from the board manufacturer.

Non-x86 PC/104 CPU boards based on ARM or PowerPC are also commercially available. However, such boards are not capable of running off-the-shelf PC software. In these cases, a Board Support Package is usually provided by the manufacturer for the supported operating system(s).

Spelling variations and abbreviations

When printing "PC/104" or its variants, it is common for the forward slash or dashes to be omitted. PC/104 may be abbreviated as PC104, PCI-104 abbreviated as PCI104, etc. Additionally, it is common for PC/104-Plus to be abbreviated with a plus sign (e.g. PC104+). [13] Such abbreviations are not officially recognized in any PC/104 Consortium specifications or literature, however they have been in use for some time.

Storage

PC/104 systems often require small, non-volatile storage, such as that afforded by compact flash and solid state disk (SSD) devices. These are often more popular than mechanical (rotating) hard drives. Compared to rotating disks, flash-based storage devices have limited lifetimes in terms of write cycles, but they are faster and draw less power. Additionally, their compactness and physical durability is often better-suited to rugged PC/104 applications; the size of magnetic hard drives can be cumbersome and their many delicate parts are more susceptible to failure in harsh environments.

See also

Related Research Articles

<span class="mw-page-title-main">Industry Standard Architecture</span> Internal expansion bus in early PC compatibles

Industry Standard Architecture (ISA) is the 16-bit internal bus of IBM PC/AT and similar computers based on the Intel 80286 and its immediate successors during the 1980s. The bus was (largely) backward compatible with the 8-bit bus of the 8088-based IBM PC, including the IBM PC/XT as well as IBM PC compatibles.

<span class="mw-page-title-main">Motherboard</span> Main printed circuit board (PCB) used for a computing device

A motherboard is the main printed circuit board (PCB) in general-purpose computers and other expandable systems. It holds and allows communication between many of the crucial electronic components of a system, such as the central processing unit (CPU) and memory, and provides connectors for other peripherals. Unlike a backplane, a motherboard usually contains significant sub-systems, such as the central processor, the chipset's input/output and memory controllers, interface connectors, and other components integrated for general use.

<span class="mw-page-title-main">PC Card</span> Expansion card standard for laptop computers

PC Card is a parallel peripheral interface for laptop computers and PDAs. The Personal Computer Memory Card International Association (PCMCIA) originally introduced the 16-bit ISA-based PCMCIA Card in 1990, but renamed it to PC Card in March 1995 to avoid confusion with the name of the organization. The CardBus PC Card was introduced as a 32-bit version of the original PC Card, based on the PCI specification. The card slots are backward compatible for the original 16-bit card, older slots are not forward compatible with newer cards.

<span class="mw-page-title-main">Expansion card</span> Circuit board for connecting to a computer system to add functionality

In computing, an expansion card is a printed circuit board that can be inserted into an electrical connector, or expansion slot on a computer's motherboard to add functionality to a computer system. Sometimes the design of the computer's case and motherboard involves placing most of these slots onto a separate, removable card. Typically such cards are referred to as a riser card in part because they project upward from the board and allow expansion cards to be placed above and parallel to the motherboard.

<span class="mw-page-title-main">PCI Express</span> Computer expansion bus standard

PCI Express, officially abbreviated as PCIe or PCI-e, is a high-speed serial computer expansion bus standard, designed to replace the older PCI, PCI-X and AGP bus standards. It is the common motherboard interface for personal computers' graphics cards, sound cards, hard disk drive host adapters, SSDs, Wi-Fi and Ethernet hardware connections. PCIe has numerous improvements over the older standards, including higher maximum system bus throughput, lower I/O pin count and smaller physical footprint, better performance scaling for bus devices, a more detailed error detection and reporting mechanism, and native hot-swap functionality. More recent revisions of the PCIe standard provide hardware support for I/O virtualization.

<span class="mw-page-title-main">Single-board computer</span> Computer whose components are on a single printed circuit board

A single-board computer (SBC) is a complete computer built on a single circuit board, with microprocessor(s), memory, input/output (I/O) and other features required of a functional computer. Single-board computers are commonly made as demonstration or development systems, for educational systems, or for use as embedded computer controllers. Many types of home computers or portable computers integrate all their functions onto a single printed circuit board.

<span class="mw-page-title-main">ATX</span> Motherboard and power supply configuration

ATX is a motherboard and power supply configuration specification, patented by David Dent in 1995 at Intel, to improve on previous de facto standards like the AT design. It was the first major change in desktop computer enclosure, motherboard and power supply design in many years, improving standardization and interchangeability of parts. The specification defines the dimensions; the mounting points; the I/O panel; and the power and connector interfaces among a computer case, a motherboard, and a power supply.

<span class="mw-page-title-main">ETX (form factor)</span>

ETX, standing for Embedded Technology eXtended, is an integrated and compact 95 × 125 mm (3.7 × 4.9 in) computer-on-module (COM) form factor, which can be used in a design application much like an integrated circuit component. Each ETX COM integrates core CPU and memory functionality, the common I/O of a PC/AT, USB, audio, graphics, and Ethernet. All I/O signals as well as a full implementation of ISA and PCI buses are mapped to four high-density, low-profile connectors on the bottom side of the module.

<span class="mw-page-title-main">COM Express</span> Computer-on-module form factor

COM Express, a computer-on-module (COM) form factor, is a highly integrated and compact computer that can be used in a design application much like an integrated circuit component. Each module integrates core CPU and memory functionality, the common I/O of a PC/AT, USB, audio, graphics (PEG), and Ethernet. All I/O signals are mapped to two high density, low profile connectors on the bottom side of the module. COM Express employs a mezzanine-based approach. The COM modules plug into a baseboard that is typically customized to the application. Over time, the COM Express mezzanine modules can be upgraded to newer, backwards-compatible versions. COM Express is commonly used in Industrial, military, aerospace, gaming, medical, transportation, Internet of things, and general computing embedded applications.

In computing, the motherboard form factor is the specification of a motherboard – the dimensions, power supply type, location of mounting holes, number of ports on the back panel, etc. Specifically, in the IBM PC compatible industry, standard form factors ensure that parts are interchangeable across competing vendors and generations of technology, while in enterprise computing, form factors ensure that server modules fit into existing rackmount systems. Traditionally, the most significant specification is for that of the motherboard, which generally dictates the overall size of the case. Small form factors have been developed and implemented.

Embedded Platform for Industrial Computing (EPIC) is a computer form factor, a standard for an industrial-quality single-board computer, in use from about 2004 through 2016.

<span class="mw-page-title-main">Small Form Factor Special Interest Group</span> Standards body specializing in small electronic devices

The Small Form Factor Special Interest Group is an international non-profit standards body focused on modular computer hardware technologies used in embedded and small form factor computers and controllers. Members are mainly computer board and component manufacturers. The group was founded in 2007 and had a web site until early 2020.

ESMexpress is a very compact computer-on-module (COM) standard. It is a complete processor module that currently supports several low-power Intel and PowerPC platforms. Apart from a CPU component, every module also includes memory and a range of serial communication interfaces such as PCI Express, Gigabit Ethernet, USB, SATA, SDVO, LVDS and HD audio. These interfaces are defined in the form factor's specification, and signals are assigned to two 120-pin connectors. This fixed pin mapping ensures that different ESMexpress modules can be exchanged more easily. Consequently, ESMexpress typically does not have an onboard FPGA. The idea behind this is to implement very specialized functions in an FPGA on the COM's carrier board to ease upgrades of the system CPU through exchange of the ESMexpress module.

<span class="mw-page-title-main">Embedded System Module</span>

Embedded System Module, or ESM, is a compact computer-on-module (COM) standard. An ESM module typically includes a CPU processor, memory, module-specific I/O interfaces and a number of basic front I/O connectors. They can be plugged on a carrier board or be used as a stand-alone processor card.

<span class="mw-page-title-main">CoreExpress</span>

CoreExpress modules are complete computer-on-module (COM) highly integrated, compact computers that can be used in an embedded computer board design, much like an integrated circuit component. COMs integrate CPU, memory, graphics, and BIOS, and common I/O interfaces. The interfaces are modern, using only digital buses such as PCI Express, Serial ATA, Ethernet, USB, and HD audio. All signals are accessible on a high-density, high-speed, 220-pin connector. Although most implementations use Intel processors, the specification is open for different CPU modules.

<span class="mw-page-title-main">Qseven</span>

Qseven, a computer-on-module (COM) form factor, is a small, highly integrated computer module that can be used in a design application much like an integrated circuit component. It is smaller than other computer-on-module standards such as COM Express, ETX or XTX and is limited to very low power consuming CPUs. The maximum power consumption should be no more than 12 watts.

WinSystems is an employee owned embedded systems manufacturer specializing in ruggedized, highly reliable industrial computer systems. The company was founded by Jerry Winfield in 1982 and is headquartered in Grand Prairie, Texas.

The PC/104 Consortium is a technology consortium that was established in February 1992 by 12 companies, all sharing a vision of adapting desktop computer technology for embedded applications. Based on the technologies of a IBM PC-based single-board computer developed by American company Ampro in 1987, the PC/104 Consortium has since had a positive effect on the embedded computer marketplace and now includes over 50 member companies. The PC/104 Consortium's technological philosophy is to support legacy technology while developing new solutions for the future. Longevity is a requirement for embedded systems and one of the hallmarks of PC/104 technology.

The PCI/104-Express specification establishes a standard to use the high-speed PCI Express bus in embedded applications. It was developed by the PC/104 Consortium and adopted by member vote in March 2008. PCI Express was chosen because of its market adoption, performance, scalability, and growing silicon availability worldwide. It provides a new high-performance physical interface while retaining software compatibility with the existing PCI infrastructure.

<span class="mw-page-title-main">M.2</span> Standard for miniature computer expansion cards

M.2, pronounced m dot two and formerly known as the Next Generation Form Factor (NGFF), is a specification for internally mounted computer expansion cards and associated connectors. M.2 replaces the Mini-SATA (mSATA) standard, which uses the PCI Express Mini Card physical card layout and connectors. Employing a more flexible physical specification, M.2 allows different module widths and lengths, which, paired with the availability of more advanced interfacing features, makes M.2 more suitable than mSATA in general for solid-state storage applications, particularly in smaller devices such as ultrabooks and tablets.

References

  1. Burckle, Robert. "PC/104: The Embedded PC Mezzanine" (PDF).
  2. "PC104.com - What is PC104?". www.pc104.com. Retrieved 2021-05-19.
  3. "Why PC/104? The Need for an Embedded-PC Standard" . Retrieved 2008-01-29.
  4. "PC/104 Consortium technical update: Stackable PCs from ISA to PCI to PCI Express" . Retrieved 4 September 2014.
  5. Himpe, Vincent (2006). Visual Basic for Electronics Engineering Applications (2nd ed.). India: Segment B.V. / Elektor Electronics. p. 407. ISBN   0-905705-68-8 . Retrieved 2008-01-29.
  6. "PC/104 Embedded Consortium's History" . Retrieved 2008-01-29.
  7. Angel, Jonathan (2010-02-01). "Open standard defines tiny expansion modules". LinuxDevices.com. Retrieved 2014-03-18.
  8. "PC/104 Consortium - History" . Retrieved 2014-08-14.
  9. "PC/104 Embedded Consortium Approves PCI/104-Express Specification" . Retrieved 2014-08-14.
  10. "PC/104 Consortium Membership Directory". pc104.org. Archived from the original on June 2, 2013. Retrieved 4 September 2014.
  11. "PCI/104-Express & PCIe/104 Specification, Version 3.0" (PDF). pc104.org. February 17, 2015. Retrieved 2016-11-02.
  12. "What is PCIe/104?" . Retrieved 2014-08-08.
  13. "Example of non-standard PC/104 abbreviation" . Retrieved 8 September 2014.