ATX

Last updated
An ATX motherboard Abit-kt7-large.jpg
An ATX motherboard
Comparison of some common motherboard form factors (pen for scale) VIA Mini-ITX Form Factor Comparison.jpg
Comparison of some common motherboard form factors (pen for scale)

ATX (Advanced Technology Extended) is a motherboard and power supply configuration specification, patented by David Dent in 1995 at Intel, [1] to improve on previous de facto standards like the AT design. It was the first major change in desktop computer enclosure, motherboard and power supply design in many years, improving standardization and interchangeability of parts. The specification defines the dimensions; the mounting points; the I/O panel; and the power and connector interfaces among a computer case, a motherboard, and a power supply.

Contents

Overview

ATX is the most common motherboard design. [2] Other standards for smaller boards (including microATX, FlexATX, nano-ITX, and mini-ITX) usually keep the basic rear layout but reduce the size of the board and the number of expansion slots. Dimensions of a full-size ATX board are 12 × 9.6 in (305 × 244 mm), which allows many ATX chassis to accept microATX boards. The ATX specifications were released by Intel in 1995 and have been revised numerous times since. The most recent ATX motherboard specification is version 2.2. [3] The most recent ATX12V power supply unit specification is ATX 3.0 released in February 2022. [4] [5] [6]

EATX (Extended ATX) is a bigger version of the ATX motherboard with 12 × 13 in (305 × 330 mm) dimensions. While some dual CPU socket motherboards have been implemented in ATX, the extra size of EATX makes it the typical form factor for dual socket systems, and with sockets that support four or eight memory channels, for single socket systems with a large number of memory slots.

In 2004, Intel announced the BTX (Balanced Technology eXtended) standard, intended as a replacement for ATX. While some manufacturers adopted the new standard, Intel discontinued any future development of BTX in 2006. As of 2024, the ATX design still remains the de facto standard for personal computers.

Connectors

ATX I/O plates for motherboard rear connectors Several atx io shields (smial).jpg
ATX I/O plates for motherboard rear connectors

On the back of the computer case, some major changes were made to the AT standard. Originally AT style cases had only a keyboard connector and expansion slots for add-on card backplates. Any other onboard interfaces (such as serial and parallel ports) had to be connected via flying leads to connectors which were mounted either on spaces provided by the case or brackets placed in unused expansion slot positions. [7]

ATX allowed each motherboard manufacturer to put these ports in a rectangular area on the back of the system with an arrangement they could define themselves, though a number of general patterns depending on what ports the motherboard offers have been followed by most manufacturers. Cases are usually fitted with a snap-out panel, also known as an I/O plate or I/O shield, in one of the common arrangements. I/O plates are usually included with retail motherboards to allow installation in any suitable case. The computer will operate correctly without a plate fitted, although there will be open gaps in the case which may compromise the EMI/RFI screening and allow ingress of dirt and random foreign bodies. Panels were made that allowed fitting an AT motherboard in an ATX case. Some ATX motherboards come with an integrated I/O plate.

ATX also made the PS/2-style mini-DIN keyboard and mouse connectors ubiquitous. AT systems used a 5-pin DIN connector for the keyboard and were generally used with serial port mice (although PS/2 mouse ports were also found on some systems). Many modern motherboards are phasing out the PS/2-style keyboard and mouse connectors in favor of the more modern Universal Serial Bus. Other legacy connectors that are slowly being phased out of modern ATX motherboards include 25-pin parallel ports and 9-pin RS-232 serial ports. In their place are onboard peripheral ports such as Ethernet, FireWire, eSATA, audio ports (both analog and S/PDIF), video (analog D-sub, DVI, HDMI, or DisplayPort), extra USB ports, and Wi-Fi.

A notable issue with the ATX specification was that it was last revised when power supplies were normally placed at the top of many old computer cases rather than at the bottom, as with many modern computer cases. This has led to some problematic standard locations for ports, in particular the 4/8 pin CPU power, which is normally located along the top edge of the board, convenient for top-mounted power supplies. This makes it very difficult for cables from bottom-mounted power supplies to reach, and commonly requires a special cutout in the back plane for the cable to come in from behind and bend around the board, making insertion and wire management very difficult. Many power supply cables barely or fail to reach, or are too stiff to make the bend, and extensions are sometimes required due to this placement. Modern power supplies often have longer cables to alleviate this issue.

Variants

ATX, Mini-ITX, and AT motherboard compatible dimensions and bore positions ATX ITX AT Motherboard Compatible Dimensions.svg
ATX, Mini-ITX, and AT motherboard compatible dimensions and bore positions
ATX motherboard size comparison; rear is on left. .mw-parser-output .legend{page-break-inside:avoid;break-inside:avoid-column}.mw-parser-output .legend-color{display:inline-block;min-width:1.25em;height:1.25em;line-height:1.25;margin:1px 0;text-align:center;border:1px solid black;background-color:transparent;color:black}.mw-parser-output .legend-text{} microATX (244 x 244 mm) Standard ATX (305 x 244 mm) Ultra ATX (366 x 244 mm) Extended ATX (EATX) (305 x 330 mm) WTX (356 x 425 mm) SSI MEB (411 x 330 mm) Form Factor dimension.png
ATX motherboard size comparison; rear is on left.
   microATX (244 × 244 mm)
  Standard ATX (305 × 244 mm)
  Ultra ATX (366 × 244 mm)
  Extended ATX (EATX) (305 × 330 mm)
   WTX (356 × 425 mm)
   SSI MEB (411 × 330 mm)

Several ATX-derived designs have been specified that use the same power supply, mountings and basic back panel arrangement, but set different standards for the size of the board and number of expansion slots. Standard ATX provides seven slots at 0.8 in (20 mm) spacing; the popular microATX size removes 2.4 inches (61 mm) and three slots, leaving four. Here width refers to the distance along the external connector edge, while depth is from front to rear. Note each larger size inherits all previous (smaller) colors area.

AOpen has conflated the term Mini ATX with a more recent[ when? ]15 × 15 cm (5.9 × 5.9 in) design. Since references to Mini ATX have been removed from ATX specifications since the adoption of microATX, the AOpen definition is the more contemporary term and the one listed above is apparently only of historical significance. This sounds contradictory to the now common Mini-ITX standard (17 × 17 cm (6.7 × 6.7 in)), which is a potential source of confusion. A number of manufacturers have added one to three additional expansion slots (at the standard 0.8 inch spacing) to the standard 12-inch ATX motherboard width.

Form factors considered obsolete in 1999 included Baby-AT, full size AT, and the semi-proprietary LPX for low-profile cases. Proprietary motherboard designs such as those by Compaq, Packard-Bell, Hewlett Packard and others existed, and were not interchangeable with multi-manufacturer boards and cases. Portable and notebook computers and some 19-inch rackmount servers have custom motherboards unique to their particular products. [8]

Form factorOriginatedDateMax. size [a]
depth × width		SlotsNotes
(typical usage, market adoption, etc.)
ATXIntel199512 × 9.6 in (305 × 244 mm)7 [b] Original, successor to AT motherboard
Proprietary, specific to crypto-mining specific motherboardsUn­known201112 × 8 in (305 × 203 mm)33 double-slot add-in cards with 1 slots of free space in between
SSI CEB SSI  ?12 × 10.5 in (305 × 267 mm)7Compact Electronics Bay
SSI MEB SSI201116.2 × 13 in (411 × 330 mm)12Midrange Electronics Bay
SSI EEB SSI ?12 × 13 in (305 × 330 mm)7Enterprise Electronics Bay
SSI TEB SSI ?12 × 10.5 in (305 × 267 mm)7Thin Electronics Bay, for rack-mount, has board component height specification
microATX Intel19979.6 × 9.6 in (244 × 244 mm)4Fits in ATX, and EATX cases.
FlexATX Intel19979 × 7.5 in (229 × 191 mm)3
Extended ATX (standard)Supermicro / Asus  ?12 × 13 in (305 × 330 mm)7Screw holes not completely compatible with some ATX cases. Intended for two CPU sockets.
Extended ATX (commonly)Un­known ?12 × 10.1 in (305 × 257 mm)
12 × 10.4 in (305 × 264 mm)
12 × 10.5 in (305 × 267 mm)
12 × 10.7 in (305 × 272 mm)		7ATX pattern screw holes
EE-ATXSupermicro ?13.68 × 13 in (347 × 330 mm)7Enhanced Extended ATX
Ultra ATXFoxconn200814.4 × 9.6 in (366 × 244 mm) [9] 10Intended for multiple double-slot video cards, and dual CPUs.
XL-ATX EVGA 200913.5 × 10.3 in (343 × 262 mm)9
XL-ATXGigabyte201013.58 x 10.31 in (345 x 262 mm)7
XL-ATX MSI 201013.6 × 10.4 in (345 × 264 mm)7
WTX Intel199814 × 16.75 in (356 × 425 mm).9Discontinued 2008
Mini-ITX VIA 20016.7 x 6.7in (170 × 170 mm).1Originally designed for home theatre or other fanless applications
Mini-DTX AMD 20078 × 6.7 in (203 × 170 mm)2Derived from Mini-ITX and DTX
BTX Intel200412.8 × 10.5 in (325 × 267 mm)7Canceled 2006. Also micro, nano, and pico variants. Not generally compatible with ATX mounting.
HPTXEVGA201013.6 × 15 in (345 × 381 mm)6Dual processors, 12 RAM slots
SWTX Supermicro200616.48 × 13 in (419 × 330 mm)
and others		5Quad processors, not compatible with ATX mounting
YTX Asus, MSI
& Maxsun		20236.89 × 9.65 in (175 × 245 mm)1New form factor supporting the DIY-APE initiative

Although true E-ATX is 12 × 13 in (305 × 330 mm) most motherboard manufacturers also refer to motherboards with measurements 12 × 10.1 in (305 × 257 mm), 12 × 10.4 in (305 × 264 mm), 12 × 10.5 in (305 × 267 mm) and 12 × 10.7 in (305 × 272 mm) as E-ATX. While E-ATX and SSI EEB (Server System Infrastructure (SSI) Forum's Enterprise Electronics Bay (EEB)) share the same dimensions, the screw holes of the two standards do not all align; rendering them incompatible.[ citation needed ]

In 2008, Foxconn unveiled a Foxconn F1 motherboard prototype, which has the same width as a standard ATX motherboard, but an extended 14.4" length to accommodate 10 slots. [10] The firm called the new 14.4 × 9.6 in (366 × 244 mm) design of this motherboard "Ultra ATX" [11] in its CES 2008 showing. Also unveiled during the January 2008 CES was the Lian Li Armorsuit PC-P80 case with 10 slots designed for the motherboard. [12]

The name "XL-ATX" has been used by at least three companies in different ways:

In 2010, EVGA Corporation released a new motherboard, the "Super Record 2", or SR-2, whose size surpasses that of the "EVGA X58 Classified 4-Way SLI". The new board is designed to accommodate two Dual QPI LGA1366 socket CPUs (e.g. Intel Xeon), similar to that of the Intel Skulltrail motherboard that could accommodate two Intel Core 2 Quad processors and has a total of seven PCI-E slots and 12 DDR3 RAM slots. The new design is dubbed "HPTX" and is 13.6 × 15 in (345 × 381 mm). [15]

Power supply

The ATX specification requires the power supply to produce three main outputs, +3.3 V, +5 V and +12 V. Low-power −12 V and +5 VSB (standby) supplies are also required. The −12 V supply is primarily used to provide the negative supply voltage for RS-232 ports and is also used by one pin on conventional PCI slots primarily to provide a reference voltage for some models of sound cards. The 5 VSB supply is used to produce trickle power to provide the soft-power feature of ATX when a PC is turned off, as well as powering the real-time clock to conserve the charge of the CMOS battery. A −5 V output was originally required because it was supplied on the ISA bus; it was removed in later versions of the ATX standard, as it became obsolete with the removal of the ISA bus expansion slots (the ISA bus itself is still found in any computer which is compatible with the old IBM PC specification).

Originally, the motherboard was powered by one 20-pin connector. An ATX power supply provides a number of peripheral power connectors and (in modern systems) two connectors for the motherboard: an 8-pin (or 4+4-pin) auxiliary connector providing additional power to the CPU and a main 24-pin power supply connector, an extension of the original 20-pin version. 20-pin Molex 39-29-9202 at the motherboard. 20-pin Molex 39-01-2200 at the cable. The connector pin pitch is 4.20 mm [16] (about one sixth of an inch).

Pinouts of ATX 2.x motherboard power connectors, 24-pin (top) and four-pin "P4" (bottom), as viewed into mating side of the plugs ATX PS signals.svg
Pinouts of ATX 2.x motherboard power connectors, 24-pin (top) and four-pin "P4" (bottom), as viewed into mating side of the plugs
ATX 20-PIN ATX 20-PIN.png
ATX 20-PIN
24-pin ATX motherboard power plug; pins 11, 12, 23 and 24 form a detachable separate four-pin plug, making it backward-compatible with 20-pin ATX receptacles 24-pin ATX power plug from a Seasonic PSU 20131105.jpg
24-pin ATX motherboard power plug; pins 11, 12, 23 and 24 form a detachable separate four-pin plug, making it backward-compatible with 20-pin ATX receptacles
24-pin ATX12V 2.x power supply connector
ColorSignal [A] Pin [B] Pin [B] [C] Signal [A] Color
Orange+3.3 V113+3.3 VOrange
+3.3 V sense [D] Brown
Orange+3.3 V214−12 VBlue
BlackGround315GroundBlack
Red+5 V416Power on [E] Green
BlackGround517GroundBlack
Red+5 V618GroundBlack
BlackGround719GroundBlack
Grey Power good [F] 820Reserved [G] None
Purple+5 V standby921+5 VRed
Yellow+12 V1022+5 VRed
Yellow+12 V1123+5 VRed
Orange+3.3 V1224GroundBlack
  1. 1 2   Light-blue background denotes control signals.
  2. 1 2   Light-green background denotes the pins present only in the 24-pin connector.
  3. ↑ In the 20-pin connector, pins 13–22 are numbered 11–20 respectively.
  4. ↑ Supplies +3.3 V power and also has a second low-current wire for remote sensing. [18]
  5. ↑ A control signal that is pulled up to +5 V by the PSU and must be driven low to turn on the PSU.
  6. ↑ A control signal that is low when other outputs have not yet reached, or are about to leave, correct voltages.
  7. ↑ Formerly −5 V (  white wire), absent in modern power supplies; it was optional in ATX and ATX12V v1.2 and deleted since v1.3.
ATX12VO power supply connector
ColorSignalPinPinSignalColor
Green PS_ON# 16 PWR_OK Gray
BlackCOM27+12 VSBPurple
BlackCOM38+12 V1 DCYellow
BlackCOM49+12 V1 DCYellow
TBDReserved510+12 V1 DC
Voltage Sensing Pin		Yellow
Molex connector part numbers
PinsFemale/receptacle
on PS cable		Male/vertical header
on PCB		Male/plug
extender cable
4-pin39-01-204039-28-104339-01-2046
20-pin39-01-220039-28-120339-01-2206
24-pin39-01-224039-28-124339-01-2246

Four wires have special functions:

Generally, supply voltages must be within ±5% of their nominal values at all times. The little-used negative supply voltages, however, have a ±10% tolerance. There is a specification for ripple in a 10 Hz–20 MHz bandwidth: [3]

Supply (V)ToleranceRange, min. to max. (V)Ripple, p. to p., max. (mV)
+5±5% (±0.25 V)+4.75 V to +5.2550
−5±10% (±0.50 V)−4.50 V to −5.5050
+12±5% (±0.60 V)+11.40 V to +12.60120
−12±10% (±1.20 V)−10.80 V to −13.20120
+3.3±5% (±0.165 V)+3.135 V to +3.46550
+5 standby±5% (±0.25 V)+4.75 V to +5.2550

The 20–24-pin Molex Mini-Fit Jr. has a power rating of, 9 amperes maximum per pin). [21] As large server motherboards and 3D graphics cards have required progressively more and more power to operate, it has been necessary to revise and extend the standard beyond the original 20-pin connector, to allow more current using multiple additional pins in parallel. The low circuit voltage is the restriction on power flow through each connector pin; at the maximum rated voltage, a single Mini-Fit Jr pin would be capable of 4800 watts.

Physical characteristics

ATX power supplies generally have the dimensions of 150 × 86 × 140 mm (5.9 × 3.4 × 5.5 in), [22] : 23–24  with the width and height being the same as the preceding LPX (Low Profile eXtension) form factor (which are often incorrectly referred to as "AT" power supplies due to their ubiquitous use in later AT and Baby AT systems, even though the actual AT and Baby AT power supply form factors were physically larger) and share a common mounting layout of four screws arranged on the back side of the unit. That last dimension, the 140 mm depth, is frequently varied, with depths of 160, 180, 200 and 230 mm used to accommodate higher power, larger fan and/or modular connectors.

Main changes from AT and LPX designs

Power switch

Original AT cases (flat case style) have an integrated power switch that protruded from the power supply and sits flush with a hole in the AT chassis. It utilizes a paddle-style DPST switch and is similar to the PC and PC-XT style power supplies.

Later AT (so-called "Baby AT") and LPX style computer cases have a power button that is directly connected to the system computer power supply (PSU). The general configuration is a double-pole latching mains voltage switch with the four pins connected to wires from a four-core cable. The wires are either soldered to the power button (making it difficult to replace the power supply if it failed) or blade receptacles were used.

Typical ATX 1.3 power supply. From left to right, the connectors are 20-pin motherboard, 4-pin "P4 connector", fan RPM monitor (note the lack of a power wire), SATA power connector (black), "Molex connector" and floppy connector. ATX-Netzteil.jpg
Typical ATX 1.3 power supply. From left to right, the connectors are 20-pin motherboard, 4-pin "P4 connector", fan RPM monitor (note the lack of a power wire), SATA power connector (black), "Molex connector" and floppy connector.
Interior view in an ATX power supply ATX power supply interior.jpg
Interior view in an ATX power supply

An ATX power supply is typically controlled by an electronic switch connected to the power button on the computer case and allows the computer to be turned off by the operating system. In addition, many ATX power supplies have a manual switch on the back that also ensures no power is being sent to the components. When the switch on the power supply is turned off, the computer cannot be turned on with the front power button.

Power connection to the motherboard

The power supply's connection to the motherboard was changed from the older AT and LPX standards; AT and LPX had two similar connectors that could be accidentally interchanged by forcing the different keyed connectors into place, usually causing short-circuits and irreversible damage to the motherboard (the rule of thumb for safe operation was to connect the side-by-side connectors with the black wires together). ATX uses one large, keyed connector which can not be connected incorrectly. The new connector also provides a 3.3 volt source, removing the need for motherboards to derive this voltage from the 5 V rail. Some motherboards, particularly those manufactured after the introduction of ATX but whilst LPX equipment was still in use, support both LPX and ATX PSUs. [23]

If using an ATX PSU for purposes other than powering an ATX motherboard, power can be fully turned on (it is always partly on to operate "wake-up" devices) by shorting the "power-on" pin on the ATX connector (pin 16, green wire) to a black wire (ground), which is what the power button on an ATX system does. A minimum load on one or more voltages may be required (varies by model and vendor); the standard does not specify operation without a minimum load and a conforming PSU may shut down, output incorrect voltages, or otherwise malfunction, but will not be hazardous or damaged. [24] An ATX power supply is not a replacement for a current-limited bench laboratory DC power supply; instead it is better described as a bulk DC power supply. [25]

Airflow

The original ATX specification called for a power supply to be located near to the CPU with the power supply fan drawing in cooling air from outside the chassis and directing it onto the processor. It was thought that in this configuration, cooling of the processor would be achievable without the need of an active heatsink. [26] This recommendation was removed from later specifications; modern ATX power supplies usually exhaust air from the case.

ATX power supply revisions

Original ATX

ATX, introduced in late 1995, defined three types of power connectors:

  • 4-pin "Molex connector" – transferred directly from AT standard: +5 V and +12 V for P-ATA hard disks, CD-ROMs, 5.25 inch floppy drives and other peripherals. [27]
  • 4-pin Berg floppy connector – transferred directly from AT standard: +5 V and +12 V for 3.5 inch floppy drives and other peripherals. [28]
  • 20-pin Molex Mini-fit Jr. ATX motherboard connector – new to the ATX standard.
  • A supplemental 6-pin AUX connector providing additional 3.3 V and 5 V supplies to the motherboard, if needed. This was used to power the CPU in motherboards with CPU voltage regulator modules which required 3.3 volt and/or 5 volt rails and could not get enough power through the regular 20-pin header.

The power distribution specification defined that most of the PSU's power should be provided on 5 V and 3.3 V rails, because most of the electronic components (CPU, RAM, chipset, PCI, AGP and ISA cards) used 5 V or 3.3 V for power supply. The 12 V rail was only used by computer fans and motors of peripheral devices (HDD, FDD, CD-ROM, etc.)

ATX12V 1.x

While designing the Pentium 4 platform in 1999/2000, the standard 20-pin ATX power connector was found insufficient to meet increasing power-line requirements; the standard was significantly revised into ATX12V 1.0 (ATX12V 1.x is sometimes inaccurately called ATX-P4). ATX12V 1.x was also adopted by AMD Athlon XP and Athlon 64 systems. However, some early model Athlon XP and MP boards (including some server boards) and later model lower-end motherboards do not have the 4-pin connector as described below.

Numbering of the ATX revisions may be a little confusing: ATX refers to the design, and goes up to version 2.2 in 2004 (with the 24 pins of ATX12V 2.0), while ATX12V describes only the PSU. For instance, ATX 2.03 is quite commonly seen on PSUs from 2000 and 2001 and often includes the P4 12V connector, even if the norm itself did not define it yet. [3]

ATX12V 1.0

The main changes and additions in ATX12V 1.0 (released in February 2000) were:

  • Increased the power on the 12 V rail (power on 5 V and 3.3 V rails remained mostly the same).
  • An extra 4-pin Mini Fit Jr. (Molex 39-01-2040), 12-volt connector to power the CPU. [22]
  • Minimum 68% efficiency at full load.

Formally called the +12 V Power Connector, this is commonly referred to as the P4 connector because this was first needed to support the Pentium 4 processor.

Before the Pentium 4, processors were generally powered from the 5 V rail. Later processors operate at much lower voltages, typically around 1 V and some draw over 100 A. It is infeasible to provide power at such low voltages and high currents from a standard system power supply, so the Pentium 4 established the practice of generating it with a DC-to-DC converter on the motherboard next to the processor, powered by the 4-pin 12 V connector.

ATX12V 1.1

This is a minor revision from August 2000. The power on the 3.3 V rail was slightly increased and other smaller changes were made.

ATX12V 1.2

A relatively minor revision from January 2002. The only significant change was that the −5 V rail was no longer required (it became optional). This voltage was required by the ISA bus, which is no longer present on almost all modern computers.

ATX12V 1.3

Introduced in April 2003 (a month after 2.0). This standard introduced some changes, mostly minor. Some of them are:

  • Slightly increased the power on 12 V rail.
  • Increased minimal efficiency for full load from 68% to 70% and defined minimal required PSU efficiencies for light (50% minimal efficiency) and typical (60% minimal efficiency) loads.
  • Defined acoustic levels.
  • Introduction of Serial ATA power connector (but defined as optional).
  • Guidance for the −5 V rail was removed (but it was not prohibited). [29]

ATX12V 2.x

ATX12V 2.x brought a significant design change regarding power distribution. By analyzing the power demands of then-current PCs, it was determined that it would be much cheaper and more practical to power most PC components from 12 V rails, instead of from 3.3 V and 5 V rails.

In particular, PCI Express expansion cards take much of their power from the 12 V rail (up to 5.5 A), while the older AGP graphics cards took only up to 1 A on 12 V and up to 6 A on 3.3 V. The CPU is also driven by a 12 V rail, while it was done by a 5 V rail on older PCs (before the Pentium 4).

ATX12V 2.0
ATX-450PNF by FSP Group Power Supply ATX-450PNF.jpg
ATX-450PNF by FSP Group

The power demands of PCI Express were incorporated in ATX12V 2.0 (introduced in February 2003), which defined quite different power distribution from ATX12V 1.x:

  • Most power is now provided on 12 V rails. The standard specifies that two independent 12 V rails (12 V2 for the four-pin connector and 12 V1 for everything else) with independent overcurrent protection are needed to meet the power requirements safely (some very high power PSUs have more than two rails; recommendations for such large PSUs are not given by the standard).
  • The power on 3.3 V and 5 V rails was significantly reduced.
  • The ATX motherboard connector was extended to 24 pins. The extra four pins provide one additional 3.3 V, 5 V and 12 V circuit.
  • The six-pin AUX connector from ATX12V 1.x was removed because the extra 3.3 V and 5 V circuits which it provided are now incorporated in the 24-pin ATX motherboard connector.
  • The power supply is required to include a Serial ATA power cable.
  • Minimum efficiency of 60% for light load, 70% for typical load, and 70% for full load
  • Many other specification changes and additions
ATX12V 2.01

This is a minor revision from June 2004. An errant reference for the −5 V rail was removed. Other minor changes were introduced. [30]

ATX12V 2.1

This is a minor revision from March 2005. The power was slightly increased on all rails. Efficiency requirements changed: minimum 65% at light load, 72% at typical load, and 70% at full load. Introduced recommended minimum values of 75% at light load, 80% at typical load, and 77% at full load.

ATX12V 2.2

Also released in March 2005 [3] it includes corrections and specifies High Current Series wire terminals for 24-pin ATX motherboard and 4-pin +12 V power connectors.

ATX12V 2.3

Effective March 2007. Recommended efficiency was increased to 80% (with at least 70% required) and the 12 V minimum load requirement was lowered. Higher efficiency generally results in less power consumption (and less waste heat) and the 80% recommendation brings supplies in line with new Energy Star 4.0 mandates. [31] The reduced load requirement allows compatibility with processors that draw very little power during startup. [32] The absolute over-current limit of 240 VA per rail was removed, allowing 12 V lines to provide more than 20 A per rail.

ATX12V 2.31

This revision became effective in February 2008. It added a maximum allowed ripple/noise specification of 400 millivolts to the PWR_ON and PWR_OK signals, requires that the DC power must hold for more than 1 millisecond after the PWR_OK signal drops, clarified country-specific input line harmonic content and electromagnetic compatibility requirements, added a section about Climate Savers, updated recommended power supply configuration charts, and updated the cross-regulation graphs.

ATX12V 2.32

This is the unofficial name given to the later revisions of the v2.31 specifications, published in May 2020 [33]

ATX12V 2.4

The ATX12V 2.4 specifications were published in August 2021. It is specified in Revision 1.31 of the 'Design Guide for Desktop Platform Form Factors', which names this as ATX12V version 2.4. [34]

ATX12V 2.51

The specifications for ATXV12 2.51 were released in September 2021 and introduced support for Alternative Low Power Mode (ALPM) which supersedes the traditional S3 power state. Windows 10 implements this functionality as Modern Standby . [35]

ATX12V 2.52

The specifications for ATXV12 2.52 were released in October 2021 introduces minor changes to the standard, most notably it requires power supply manufacturers to ensure power supplies with Alternative Low Power Mode (ALPM) support are able to withstand power cycles every 180 seconds (480 times per day or 175,200 per year). Power supply fans are also recommended to turn on with at least a two second delay for an improved user experience. [36]

ATX12V 2.53

The specifications for ATXV12 2.53 were released in December 2021 and constitute another minor update to the ATX standard. ATXV12 2.53 makes further recommendations on efficiency and references the Energy Star Computers Specification Version 8.0 which was finalized in April 2020. [35] [37]

ATX 3.0

The specifications for ATX 3.0 were released in February 2022. It includes the new 16-pin 12VHPWR connector that can deliver up to 600 W for H+ and up to 675 W in H++ to graphics cards. These incorporate data lines for components to negotiate power capabilities with the PSU so they do not draw more power than the PSU is capable of delivering. The specification also has more strict requirements for handling spikes, two times the nominal output for 100 microseconds.

The -12V supply is now specified as optional on the ATX motherboard connector. [38]

ATX 3.1 replaces the 12VHPWR power connector with the 12V-2x6 power connector.

ATX power supply derivatives

ATX12VO

Standing for ATX 12-volt-only, this is a new specification published by Intel in 2019, aimed at pre-built systems in the first run, and stricter power efficiency requirements by the California Energy Commission going into effect in 2021. [39] Several OEMs were already using a similar design with proprietary connectors and this effectively standardizes those. [40]

Under this standard, power supplies provide only a 12 V output. ATX12VO introduces a new 10-pin connector to supply the motherboard, replacing the 24-pin ATX12V connector. This greatly simplifies power supplies, but moves DC-to-DC conversion and some connectors to the motherboard instead. Notably, SATA power connectors, which include 3.3 V and 5 V pins, need to move to the motherboard instead of being connected directly to the power supply. [40]

a. Connector pinout per Intel ATX12VO (12V Only) Desktop Power Supply Design Guide. [41]

PinSignalColourPinSignalColour
5I_PSU%Blue1012 V [12V Sensing Pin]Yellow
4GNDBlack912 VYellow
3GNDBlack812 VYellow
2GNDBlack712 V SBPurple
1PS_ON#Green6PWR_OKGray

SFX

An SFX power supply unit SFX PC-PSU Delta IMG 9760.JPG
An SFX power supply unit

SFX (Small Form-Factor eXtended) [42] is merely a design for a small form factor (SFF) power supply casing (such as those using microATX, FlexATX, nano-ITX, mini-ITX, and NLX), with the power specifications almost identical to ATX. Thus, an SFX power supply is mostly pin-compatible with the ATX power supply as the main difference is its reduced dimensions; the only electrical difference is that the SFX specifications do not require the −5 V rail. Since −5 V is required only by some ISA-bus expansion cards, this is not an issue with modern hardware and decreases productions costs. As a result, ATX pin 20, which carried −5 V, is absent in current power supplies; it was optional in ATX and ATX12V version 1.2 and deleted as of ATX version 1.3.

SFX has dimensions of 125 × 63.5 × 100 mm (width × height × depth), with a 60 mm fan, compared with the standard ATX dimensions of 150 × 86 × 140 mm. Optional 80 or 40 mm fan replacement increases or decreases the height of an SFX unit. [43]

Some manufacturers and retailers incorrectly market SFX power supplies as μATX or MicroATX power supplies. [44]

Some manufacturers make SFX-L dimensions of 125 × 63.5 × 130 mm to accommodate a 120 mm fan. [45]

TFX

A TFX power supply unit TFX power supply unit.jpg
A TFX power supply unit

Thin Form Factor is another small power supply design with standard ATX specification connectors. Its dimensions are generally (W × H × D): 85 × 64 × 175 mm (3.34 × 2.52 × 6.89 in). [46] [47]

WTX

WTX power supplies provide a WTX style motherboard connector which is incompatible with the standard ATX motherboard connector.

AMD GES

This is an ATX12V power supply derivative made by AMD to power its Athlon MP (dual processor) platform. It was used only on high-end Athlon MP motherboards. It has a special 8-pin supplemental connector for motherboard, so an AMD GES PSU is required for such motherboards (those motherboards will not work with ATX(12 V) PSUs).

a. ATX12V-GES 24-pin P1 motherboard connector. The pinout on the motherboard connector is as follows when viewing the motherboard from above:

PinSignalColourPinSignalColour
1212 VYellow2412 VYellow
1112 VYellow23GNDBlack
10GNDBlack22GNDBlack
9GNDBlack213.3 VOrange
83.3 VOrange203.3 VOrange
73.3 VOrange193.3 VOrange
6GNDBlack18GNDBlack
5PS_ON_NGreen17−12 VBlue
4GNDBlack165 V SBPurple
3GNDBlack15GNDBlack
25 VRed145 VRed
15 VRed135 VRed

b. ATX12V-GES 8-pin P2 motherboard connector. This pinout on the motherboard connector is as follows when viewing the motherboard from above:

PinSignalColourPinSignalColour
4GNDBlack812 VYellow striped black
3GNDBlack712 VYellow striped black
2PWR_OKGray612 VYellow striped black
15 VRed5GNDBlack

EPS12V

EPS12V is defined in Server System Infrastructure (SSI) and used primarily by SMP/multi-core systems such as Core 2, Core i7, Opteron and Xeon. It has a 24-pin ATX motherboard connector (same as ATX12V v2.x), an 8-pin secondary connector and an optional 4-pin tertiary connector. Rather than include the extra cable, many power supply makers implement the 8-pin connector as two combinable 4-pin connectors to ensure backwards compatibility with ATX12V motherboards.

Specification changes and additions

High-performance video card power demands dramatically increased during the 2000s and some high-end graphics cards have power demands that exceed AGP or PCIe slot capabilities. For these cards, supplementary power was delivered through a standard 4-pin peripheral or floppy power connector. Midrange and high-end PCIe graphics cards manufactured after 2004 typically use a standard 6- or 8-pin PCIe power connector directly from the PSU.

Interchanging PSUs

Although the ATX power supply specifications are mostly vertically compatible in both ways (both electrically and physically), there are potential issues with mixing old motherboards/systems with new PSUs and vice versa. The main issues to consider are the following:

This is a practical guidance what to mix and what not to mix:

Some proprietary brand-name systems require a matching proprietary power supply, but some of them may also support standard and interchangeable power supplies.

Efficiency

Efficiency in power supplies means the extent to which power is not wasted in converting electricity from a household supply to regulated DC. Computer power supplies vary from around 70% to over 90% efficiency.

Various initiatives exist to improve the efficiency of computer power supplies. Climate Savers Computing Initiative promotes energy saving and reduction of greenhouse gas emissions by encouraging development and use of more efficient power supplies. 80 PLUS certifies a variety of efficiency levels for power supplies and encourages their use via financial incentives. Efficient power supplies also save money by wasting less power; as a result they use less electricity to power the same computer, and they emit less waste heat which results in significant energy savings on central air conditioning in the summer. The gains of using an efficient power supply are more substantial in computers that use a lot of power.

Although a power supply with a larger than needed power rating will have an extra margin of safety against overloading, such a unit is often less efficient and wastes more electricity at lower loads than a more appropriately sized unit. For example, a 900-watt power supply with the 80 Plus Silver efficiency rating (which means that such a power supply is designed to be at least 85 percent efficient for loads above 180 W) may only be 73% efficient when the load is lower than 100 W, which is a typical idle power for a desktop computer. Thus, for a 100 W load, losses for this supply would be 27 W; if the same power supply was put under a 450 W load, for which the supply's efficiency peaks at 89%, the loss would be only 56 W despite supplying 4.5 times the useful power. [49] [50] For a comparison, a 500-watt power supply carrying the 80 Plus Bronze efficiency rating (which means that such a power supply is designed to be at least 82-percent efficient for loads above 100 W) may provide an 84 percent efficiency for a 100 W load, wasting only 19 W. [51]

See also

Explanatory notes

  1. ↑ For boards which take expansion slots, the length of the expansion card aligns with the depth of the system board. The case may support cards longer than the depth of the mainboard.
  2. ↑ Most common ATX motherboards have 6 slots despite having the physical sizing for 7 slots.

Related Research Articles

<span class="mw-page-title-main">Motherboard</span> Main printed circuit board used for a computing device

A motherboard is the main printed circuit board (PCB) in general-purpose computers and other expandable systems. It holds and allows communication between many of the crucial electronic components of a system, such as the central processing unit (CPU) and memory, and provides connectors for other peripherals. Unlike a backplane, a motherboard usually contains significant sub-systems, such as the central processor, the chipset's input/output and memory controllers, interface connectors, and other components integrated for general use.

<span class="mw-page-title-main">PCI Express</span> Computer expansion bus standard

PCI Express, officially abbreviated as PCIe or PCI-e, is a high-speed serial computer expansion bus standard, meant to replace the older PCI, PCI-X and AGP bus standards. It is the common motherboard interface for personal computers' graphics cards, capture cards, sound cards, hard disk drive host adapters, SSDs, Wi-Fi, and Ethernet hardware connections. PCIe has numerous improvements over the older standards, including higher maximum system bus throughput, lower I/O pin count and smaller physical footprint, better performance scaling for bus devices, a more detailed error detection and reporting mechanism, and native hot-swap functionality. More recent revisions of the PCIe standard provide hardware support for I/O virtualization.

<span class="mw-page-title-main">SATA</span> Computer bus interface for storage devices

SATA is a computer bus interface that connects host bus adapters to mass storage devices such as hard disk drives, optical drives, and solid-state drives. Serial ATA succeeded the earlier Parallel ATA (PATA) standard to become the predominant interface for storage devices.

<span class="mw-page-title-main">Quiet PC</span> Type of personal computer

A quiet, silent or fanless PC is a personal computer that makes very little or no noise. Common uses for quiet PCs include video editing, sound mixing and home theater PCs, but noise reduction techniques can also be used to greatly reduce the noise from servers. There is currently no standard definition for a "quiet PC", and the term is generally not used in a business context, but by individuals and the businesses catering to them.

<span class="mw-page-title-main">DC connector</span> Electrical connector for carrying DC power

A DC connector is an electrical connector that supplies direct current (DC) power.

<span class="mw-page-title-main">Mini-ITX</span> 17 × 17 cm motherboard

Mini-ITX is a 170 mm × 170 mm motherboard form factor developed by VIA Technologies in 2001. Mini-ITX motherboards have been traditionally used in small-configured computer systems. Originally, Mini-ITX was a niche standard designed for fanless cooling with a low power consumption architecture, which made them useful for home theater PC systems, where fan noise can detract from the cinema experience.

<span class="mw-page-title-main">BTX (form factor)</span> Form factor for motherboards

BTX is a form factor for motherboards, originally intended to be the replacement for the aging ATX motherboard form factor in late 2004 and early 2005.

<span class="mw-page-title-main">Computer fan control</span> Management of the rotational speed of a computer fan

Fan control is the management of the rotational speed of an electric fan. In computers, various types of computer fans are used to provide adequate cooling, and different fan control mechanisms balance their cooling capacities and noise they generate. This is commonly accomplished by the motherboards having hardware monitoring circuitry, which can be configured by the end-user through BIOS or other software to perform fan control.

<span class="mw-page-title-main">AT (form factor)</span> Size and layout of the IBM AT computers motherboard, used to design compatible products

In the era of IBM compatible personal computers, the AT form factor comprises the dimensions and layout of the motherboard for the IBM AT. Baby AT motherboards are slightly smaller, measuring 8.5" by 13". Like the IBM PC and IBM XT models before it, many third-party manufacturers produced motherboards compatible with the IBM AT form factor, allowing end users to upgrade their computers for faster processors. The IBM AT became a widely copied design in the booming home computer market of the 1980s. IBM clones made at the time began using AT compatible designs, contributing to its popularity. In the 1990s many computers still used AT and its variants. Since 1997, the AT form factor has been largely supplanted by ATX.

<span class="mw-page-title-main">Computer case</span> Enclosure that contains most of the computer hardware

A computer case, also known as a computer chassis, is the enclosure that contains most of the hardware of a personal computer. The components housed inside the case are referred as the internal hardware, while hardware outside the case are known as peripherals.

<span class="mw-page-title-main">LPX (form factor)</span>

LPX, originally developed by Western Digital, was a loosely defined motherboard format widely used from 1987 to the late 1990s.

<span class="mw-page-title-main">WTX (form factor)</span> Motherboard form factor specification

WTX was a motherboard form factor specification introduced by Intel at the IDF in September 1998, for its use at high-end, multiprocessor, multiple-hard-disk servers and workstations. The specification had support from major OEMs and motherboard manufacturers and was updated (1.1) in February 1999. As of 2008, the specification has been discontinued and the URL www.wtx.org no longer hosts a website and has not been owned by Intel since at least 2004.

<span class="mw-page-title-main">PC/104</span> Computer standard family

PC/104 is a family of embedded computer standards which define both form factors and computer buses by the PC/104 Consortium. Its name derives from the 104 pins on the interboard connector (ISA) in the original PC/104 specification and has been retained in subsequent revisions, despite changes to connectors. PC/104 is intended for specialized environments where a small, rugged computer system is required. The standard is modular, and allows consumers to stack together boards from a variety of COTS manufacturers to produce a customized embedded system.

microATX Standard motherboard form factor

In computer design, microATX is a standard motherboard form factor introduced in December 1997. The maximum size of a microATX motherboard is 9.6 × 9.6 in (244 × 244 mm). However, there are examples of motherboards using microATX designation despite having a smaller size of 244 × 205 mm (9.6 × 8.1 in). The standard ATX size is 25% longer, at 12 × 9.6 in (305 × 244 mm).

<span class="mw-page-title-main">Small form factor PC</span> Form factor for desktop computers and motherboards

Small form factor (SFF) is a classification of desktop computers and for some of their components, chassis and motherboard, to indicate that they are designed in accordance with one of several standardized form factors intended to minimize the volume and footprint of a desktop computer compared to the standard ATX form factor.

<span class="mw-page-title-main">IDC (electrical connector)</span> Type of electrical connector

An insulation-displacement contact (IDC), also known as insulation-piercing contact (IPC), is an electrical connector designed to be connected to the conductor(s) of an insulated cable by a connection process which forces a selectively sharpened blade or blades through the insulation, bypassing the need to strip the conductors of insulation before connecting. When properly made, the connector blade cold-welds to the conductor, making a theoretically reliable gas-tight connection.

<span class="mw-page-title-main">Molex connector</span> Two-piece pin-and-socket connector

A Molex connector is a two-piece pin-and-socket interconnection which became an early electronic standard. Developed by Molex Connector Company in the late 1950s, the design features cylindrical spring-metal pins that fit into cylindrical spring-metal sockets, both held in a rectangular matrix in a nylon shell.

<span class="mw-page-title-main">Computer fan</span> Miniature fan used in a computer for active cooling

A computer fan is any fan inside, or attached to, a computer case used for active cooling. Fans are used to draw cooler air into the case from the outside, expel warm air from inside and move air across a heat sink to cool a particular component. Both axial and sometimes centrifugal (blower/squirrel-cage) fans are used in computers. Computer fans commonly come in standard sizes, such as 92 mm, 120 mm, 140 mm, and even 200–220 mm. Computer fans are powered and controlled using 3-pin or 4-pin fan connectors.

<span class="mw-page-title-main">Power supply unit (computer)</span> Internal computer component that provides power to other components

A power supply unit (PSU) converts mains AC to low-voltage regulated DC power for the internal components of a desktop computer. Modern personal computers universally use switched-mode power supplies. Some power supplies have a manual switch for selecting input voltage, while others automatically adapt to the main voltage.

<span class="mw-page-title-main">Dell Inspiron desktop computers</span> Desktop computer series by Dell

On June 26, 2007, Dell released the new Inspiron desktop series, under the Dell Inspiron branding, as a replacement to the Dell Dimension desktop computers.

References

  1. ↑ US 5555158
  2. ↑ Mark, Soper; Prowse, David; Mueller, Scott (September 2012). Authorized Cert Guide: CompTIA A+. Pearson Education. ISBN   978-0-7897-4850-8.
  3. 1 2 3 4 5 "ATX Specification - Version 2.2" (PDF). Archived from the original (PDF) on 2012-07-25. Retrieved April 4, 2014.
  4. ↑ "ATX Version 3.0 Multi Rail Desktop Platform Power Supply Design Guide". Intel . Retrieved October 8, 2024.
  5. ↑ Mpitziopoulos, Aris (March 4, 2022). "Intel's ATX v3.0 PSU Standard Has More Power for GPUs". Tom's Hardware . Retrieved October 8, 2024. On February 1st, 2022, the ATX12V v3.0 spec became final...
  6. ↑ E. Fylladitakis (May 2, 2024). "The XPG Core Reactor II VE 850W PSU Review: Our First ATX 3.1 Power Supply". Anandtech . Retrieved October 8, 2024. The ATX v3.1 specification was officially launched on 13 September 2023, following the release of the ATX v3.0 in February 2022.
  7. ↑ Alex Campbell (2016-07-26). "A brief history of PC case design". PC Gamer. Retrieved 2023-12-09.
  8. ↑ Scott Mueller, Upgrading and Repairing PCs, Eleventh Edition, Que Books, 1999, ISBN   0-7897-1903-7, page 1255
  9. ↑ "Foxconn Reveals X48, Ultra ATX, and Shamino". 13 January 2008.
  10. ↑ "Foxconn F1 Motherboard Prototype". Hardwaresecrets.com. Archived from the original on 24 October 2014. Retrieved 18 November 2014.
  11. ↑ Thomas Soderstrom (13 January 2008). "Foxconn Reveals X48, Ultra ATX, and Shamino". Tom's Hardware. Retrieved 18 November 2014.
  12. ↑ "Lian Li Armorsuit PC-P80R Spider Edition". TechPowerUp. 11 May 2008. Retrieved 18 November 2014.
  13. ↑ "The New 4-Way SLI Platform Has Arrived!". Evga.com. Retrieved 18 November 2014.
  14. ↑ "Product list GeForce 500 Series". Archived from the original on 2011-07-16.
  15. ↑ "EVGA Corporation Super Record 2". Evga.com. Retrieved 18 November 2014.
  16. ↑ Molex. "Mini-fit Jr" (PDF). www.molex.com. Retrieved 30 January 2023.
  17. ↑ "Power Supply Design Guide for Desktop Platform Form Factors, Revision 1.31" (PDF). Intel. April 2013. p. 26. Archived from the original (PDF) on October 21, 2014. Retrieved February 6, 2015.
  18. ↑ "ATX Specification Version 2.1" (PDF). Archived from the original (PDF) on 2003-09-24.
  19. ↑ "How to Convert a Computer ATX Power Supply to a Lab Power Supply (with video) - wikiHow" . Retrieved 2013-08-17. wikihow.com
  20. ↑ "Ref - Power Supply - Functions". PCGuide. Archived from the original on 2013-08-28. Retrieved 2013-08-17.
  21. ↑ "Mini-Fit Jr. Power Connectors - Molex". Molex.com. Archived from the original on 21 October 2014. Retrieved 18 November 2014.
  22. 1 2 "AT / ATX12V Power Supply Design Guide Version 1.1" (PDF). Intel Corporation. August 2000. p. 28. Archived (PDF) from the original on 2010-12-07. Retrieved 2011-03-11.
  23. ↑ "Example of a motherboard that can support connecting AT and ATX PSUs". Createch.com. Archived from the original on 13 December 2013. Retrieved 18 November 2014.
  24. ↑ "PC Power Supply Requirements and Troubleshooting Problems". RepRap project. September 19, 2018. Archived from the original on September 19, 2018.
  25. ↑ J. B. Calvert. "Using a Computer PSU"; University of Denver.
  26. ↑ "Support for Intel® Processors".
  27. ↑ "PC peripheral power connector pinout and signals @ pinouts.ru". Pinouts.ru. Retrieved 18 November 2014.
  28. ↑ "PC floppy power connector pinout and signals @ pinouts.ru". Pinouts.ru. Retrieved 18 November 2014.
  29. ↑ "ATX12V Power Supply Design Guide Version 1.3" (PDF). Intel Corporation. April 2003. p. 38. Retrieved 2013-03-24.
  30. ↑ "ATX12V Power Supply Design Guide Version 2.01" (PDF). Intel Corporation. June 2004. p. 44. Archived from the original (PDF) on 2009-11-22. Retrieved 2013-03-24.
  31. ↑ "Design Guide for Desktop Platform Form Factors, Intel Corp" (PDF). Formfactors.org. Archived from the original (PDF) on 2015-01-14. Retrieved 18 November 2014.
  32. ↑ "#138 - Question/Answer: ATX 12V 2.2 vs. ATX 12V 2.3". YouTube. Archived from the original on 2021-12-21. Retrieved 18 November 2014.
  33. ↑ "Antec High Current Gamer Modular 750 W Review". 28 June 2013.
  34. ↑ "Power Supply Design Guide for Desktop Platform Form Factors" (PDF). Intel. April 2013. Archived (PDF) from the original on April 1, 2018. Retrieved April 1, 2018.
  35. 1 2 "Power Supply Design Guide for Desktop Platform Form Factors, Revision 003". Intel. June 2020. Retrieved February 22, 2021.
  36. ↑ "Power Supply Design Guide for Desktop Platform Form Factors Revision 002" (PDF). Intel. June 2018. Archived (PDF) from the original on March 13, 2020. Retrieved September 15, 2020.
  37. ↑ "Computers Specification Version 8.0". Energy Star. April 2020. Archived from the original on 2018-05-24. Retrieved February 22, 2021.
  38. ↑ https://edc.intel.com/content/www/us/en/design/ipla/software-development-platforms/client/platforms/alder-lake-desktop/atx-version-3-0-multi-rail-desktop-platform-power-supply-design-guide/2.0/2.1a/dc-voltage-regulation-required/
  39. ↑ "How Intel is changing the future of power supplies with its ATX12VO spec". PCWorld. 2020-03-09. Retrieved 2020-04-13.
  40. 1 2 Lathan, Patrick (2020-04-10). "Intel ATX12VO vs. 12V Spec Explained & What Manufacturers Think". GamersNexus. Retrieved 2020-04-13.
  41. ↑ "DC Connectors - 2.0 - ID:613768 | ATX12VO (12V Only) Desktop Power Supply". edc.intel.com. Retrieved 2022-11-24.
  42. ↑ "How to choose the best PSU for a Gaming Computer IN 2023?". Tic Tech. Retrieved 12 August 2023.
  43. ↑ "SFX Form Factor". Pcguide.com. Archived from the original on 11 February 2001. Retrieved 18 November 2014.
  44. ↑ List of computer PSU form factors - SilverStone Technology Co., Ltd.
  45. ↑ SFX-L Computex 2017 roundup - Small Form Factor Network
  46. ↑ Modern Form Factors: EPS, TFX, CFX, LFX, And Flex ATX - Power Supply 101: A Reference Of Specifications
  47. ↑ Power Supplies TekSpek Guide - SCAN UK
  48. ↑ "Hardware Knowledgebase - do I absolutely HAVE to plug in the ATX12V 4pin connector on P4 motherboards? - HardwareFAQs: Powered by neofaq". www.neoseeker.com. Archived from the original on October 3, 2009.
  49. ↑ Christoph Katzer (2008-09-22). "Debunking Power Supply Myths". AnandTech. p. 3. Retrieved 2014-10-07.
  50. ↑ "Cooler Master UCP Product Sheet". Cooler Master. 2008. Archived from the original (PDF) on 2014-07-28. Retrieved 2014-10-11.
  51. ↑ Martin Kaffei (2011-10-10). "SilverStone Strider Plus – 500 W Modular Power". AnandTech. p. 4. Retrieved 2014-10-11.
ATX Motherboard Specifications
ATX Power Supply Specifications
EPS Power Supply Specifications
Other
This page is based on this Wikipedia article
Text is available under the CC BY-SA 4.0 license; additional terms may apply.
Images, videos and audio are available under their respective licenses.