Accelerated Graphics Port (AGP) is a parallelexpansion card standard, designed for attaching a video card to a computer system to assist in the acceleration of 3D computer graphics. It was originally designed as a successor to PCI-type connections for video cards. Since 2004, AGP was progressively phased out in favor of PCI Express (PCIe), which is serial, as opposed to parallel; by mid-2008, PCI Express cards dominated the market and only a few AGP models were available,[1] with GPU manufacturers and add-in board partners eventually dropping support for the interface in favor of PCI Express.
AGP is a superset of the PCI standard, designed to overcome PCI's limitations in serving the requirements of the era's high-performance graphics cards.[2]
The primary advantage of AGP is that it doesn't share the PCI bus, providing a dedicated, point-to-point pathway between the expansion slot(s) and the motherboard chipset. The direct connection also allows higher clock speeds.
The second major change is the use of split transactions, wherein the address and data phases are separated. The card may send many address phases, so the host can process them in order, avoiding any long delays caused by the bus being idle during read operations.
Third, PCI bus handshaking is simplified. Unlike PCI bus transactions, whose length is negotiated on a cycle-by-cycle basis using the FRAME# and STOP# signals, AGP transfers are always a multiple of 8bytes long, with the total length included in the request. Further, rather than using the IRDY# and TRDY# signals for each word, data is transferred in blocks of 4clock cycles (32words at AGP 8× speed), and pauses are allowed only between blocks.
Finally, AGP allows (mandatory only in AGP 3.0) sideband addressing, meaning that the address and data buses are separated, so the address phase does not use the main address/data (AD) lines at all. This is done by adding an extra 8-bit "SideBand Address" bus, over which the graphics controller can issue new AGP requests while other AGP data is flowing over the main 32 address/data (AD) lines. This results in improved overall AGP data throughput.
This great improvement in memory read performance makes it practical for an AGP card to read textures directly from system RAM, while a PCI graphics card must copy it from system RAM to the card's video memory. System memory is made available using the graphics address remapping table (GART), which apportions main memory as needed for texture storage.[3] The maximum amount of system memory available to AGP is defined as the AGP aperture.
History
An AGP card
The AGP slot first appeared on x86-compatible system boards based on Socket 7 Intel P5Pentium and Slot 1P6Pentium II processors. Intel introduced AGP support with the i440LX Slot 1 chipset on August 26, 1997, and a flood of products followed from all the major system board vendors.[4]
The first Socket 7 chipsets to support AGP were the VIAApollo VP3, SiS 5591/5592, and the ALI Aladdin V. Intel never released an AGP-equipped Socket 7 chipset. FIC demonstrated the first Socket 7 AGP system board in November 1997 as the FIC PA-2012 based on the VIA Apollo VP3 chipset, followed very quickly by the EPoX P55-VP3 also based on the VIA VP3 chipset which was first to market.[5]
Early video chipsets featuring AGP support included the Rendition Vérité V2200, 3dfxVoodoo Banshee, NvidiaRIVA 128, 3Dlabs PERMEDIA 2, Intel i740, ATI Rage series, Matrox Millennium II, and S3 ViRGE GX/2. Some early AGP boards used graphics processors built around PCI and were simply bridged to AGP. This resulted in the cards benefiting little from the new bus, with the only improvement used being the 66MHz bus clock, with its resulting doubled bandwidth over PCI, and bus exclusivity. Intel's i740 was explicitly designed to exploit the new AGP feature set; in fact it was designed to texture only from AGP memory, making PCI versions of the board difficult to implement (local board RAM had to emulate AGP memory.)
Microsoft first introduced AGP support into Windows 95 OEM Service Release 2 (OSR2 version 1111 or 950B) via the USB SUPPLEMENT to OSR2 patch.[6] After applying the patch the Windows 95 system became Windows 95 version 4.00.950 B. The first Windows NT-based operating system to receive AGP support was Windows NT 4.0 with Service Pack 3, introduced in 1997. Linux support for AGP enhanced fast data transfers was first added in 1999 with the implementation of the AGPgart kernel module.
Later use
With the increasing adoption of PCIe, graphics cards manufacturers continued to produce AGP cards as the standard became obsolete. As GPUs began to be designed to connect to PCIe, an additional PCIe-to-AGP bridge-chip was required to create an AGP-compatible graphics card. The inclusion of a bridge, and the need for a separate AGP card design, incurred additional board costs.
The GeForce 6600 and ATI Radeon X800 XL, released during 2004–2005, were the first bridged cards.[7][8] In 2009 AGP cards from Nvidia had a ceiling of the GeForce 7 series. In 2011 DirectX 10-capable AGP cards from AMD vendors (Club 3D, HIS, Sapphire, Jaton, Visiontek, Diamond, etc.) included the Radeon HD 2400, 3450, 3650, 3850, 4350, 4650, and 4670. The HD 5000 AGP series mentioned in the AMD Catalyst software was never available. There were many problems with the AMD Catalyst 11.2 - 11.6 AGP hotfix drivers under Windows 7 with the HD 4000 series AGP video cards;[9] use of 10.12 or 11.1 AGP hotfix drivers is a possible workaround. Several of the vendors listed above make available past versions of the AGP drivers.
By 2010, no new motherboard chipsets supported AGP and few new motherboards had AGP slots, however some continued to be produced with older AGP-supporting chipsets.
In 2016, Windows 10 version 1607 dropped support for AGP.[10][unreliable source?] Possible future removal of support for AGP from open-source Linux kernel drivers was considered in 2020.[11][needs update]
Versions
AGP and PCI: 32-bit buses operating at 66 and 33MHz respectively
Intel released "AGP specification 1.0" in 1997.[13] It specified 3.3V signals and 1× and 2× speeds.[4] Specification 2.0 documented 1.5V signaling, which could be used at 1×, 2× and the additional 4× speed[14][15] and 3.0 added 0.8V signaling, which could be operated at 4× and 8× speeds.[16] (1× and 2× speeds are physically possible, but were not specified.)
Available versions are listed in the adjacent table.
AGP version 3.5 is only publicly mentioned by Microsoft under Universal Accelerated Graphics Port (UAGP), which specifies mandatory supports of extra registers once marked optional under AGP 3.0. Upgraded registers include PCISTS, CAPPTR, NCAPID, AGPSTAT, AGPCMD, NISTAT, NICMD. New required registers include APBASELO, APBASEHI, AGPCTRL, APSIZE, NEPG, GARTLO, GARTHI.
There are various physical interfaces (connectors); see the Compatibility section.
Official extensions
AGP graphics card (Apple Macintosh)AGP Pro graphics card
AGP Pro
An official extension for cards that required more electrical power, with a longer slot with additional pins for that purpose. AGP Pro cards were usually workstation-class cards used to accelerate professional computer-aided design applications employed in the fields of architecture, machining, engineering, simulations, and similar fields.[17]
64-bit AGP
A 64-bit channel was once proposed as an optional standard for AGP 3.0 in draft documents,[18] but it was dropped in the final version of the standard.
The standard allows 64-bit transfer for AGP8× reads, writes, and fast writes; 32-bit transfer for PCI operations.
Unofficial variations
A number of non-standard variations of the AGP interface have been produced by manufacturers.
Internal AGP interface
Ultra-AGP, Ultra-AGPII
It is an internal AGP interface standard used by SiS for the north bridge controllers with integrated graphics. The original version supports same bandwidth as AGP 8×, while Ultra-AGPII has maximum 3.2GB/s bandwidth.
PCI-based AGP ports
AGP Express
Not a true AGP interface, but allows an AGP card to be connected over the legacy PCI bus on a PCI Express motherboard. It is a technology used on motherboards made by ECS, intended to allow an existing AGP card to be used in a new motherboard instead of requiring a PCIe card to be obtained (since the introduction of PCIe graphics cards few motherboards provide AGP slots). An "AGP Express" slot is basically a PCI slot (with twice the electrical power) with an AGP connector. It offers backward compatibility with AGP cards, but provides incomplete support[19] (some AGP cards do not work with AGP Express) and reduced performance—the card is forced to use the shared PCI bus at its lower bandwidth, rather than having exclusive use of the faster AGP.
AGI
The ASRock Graphics Interface (AGI) is a proprietary variant of the Accelerated Graphics Port (AGP) standard. Its purpose is to provide AGP-support for ASRock motherboards that use chipsets lacking native AGP support. However, it is not fully compatible with AGP, and several video card chipsets are known not to be supported.
AGX
The EPoX Advanced Graphics eXtended (AGX) is another proprietary AGP variant with the same advantages and disadvantages as AGI. User manuals recommend not using AGP 8× ATI cards with AGX slots.
XGP
The Biostar Xtreme Graphics Port is another AGP variant, also with the same advantages and disadvantages as AGI and AGX.
PCIe based AGP ports
AGR
The Advanced Graphics Riser is a variation of the AGP port used in some PCIe motherboards made by MSI to offer limited backward compatibility with AGP. It is, effectively, a modified PCIe slot allowing for performance comparable to an AGP 4×/8× slot,[20] but does not support all AGP cards; the manufacturer published a list of some cards and chipsets that work with the modified slot.[21]
Compatibility
Compatibility, AGP Keys on card (top), on slot (bottom)
AGP cards are backward and forward compatible within limits. 1.5 V-only keyed cards will not go into 3.3 V slots and vice versa, though "Universal" cards exist which will fit into either type of slot. There are also unkeyed "Universal" slots that will accept either type of card. When an AGP Universal card is plugged-into an AGP Universal slot, only the 1.5 V portion of the card is used. Some cards, like Nvidia's GeForce 6 series (except the 6200) or ATI's Radeon X800 series, only have keys for 1.5 V to prevent them from being installed in older mainboards without 1.5 V support. Some of the last modern cards with 3.3 V support were:
the Nvidia GeForce FX series (FX 5200, FX 5500, FX 5700, some FX 5800, FX 5900 and some FX 5950)
certain GeForce 6 series and 7 series (few cards were made with 3.3v support except for 6200 where 3.3v support was common)
some GeForce 6200/6600/6800 and GeForce 7300/7600/7800/7900/7950 cards (really uncommon compared to their AGP 1.5v only versions)
AGP Pro cards will not fit into standard slots, but standard AGP cards will work in a Pro slot. Motherboards equipped with a Universal AGP Pro slot will accept a 1.5 V or 3.3 V card in either the AGP Pro or standard AGP configuration, a Universal AGP card, or a Universal AGP Pro card.
Some cards incorrectly have dual notches, and some motherboards incorrectly have fully open slots, allowing a card to be plugged into a slot that does not support the correct signaling voltage, which may damage card or motherboard. Some incorrectly designed older 3.3 V cards have the 1.5 V key.
There are some proprietary systems incompatible with standard AGP; for example, ApplePower Macintosh computers with the Apple Display Connector (ADC) have an extra connector which delivers power to the attached display. Some cards designed to work with a specific CPU architecture (e.g., PC, Apple) may not work with others due to firmware issues.
Mark Allen of Playtools.com made the following comments regarding Practical AGP Compatibility for AGP 3.0 and AGP 2.0:[22]
...nobody makes AGP 3.0 cards, and nobody makes AGP 3.0 motherboards. At least not any manufacturers I can find. Every single video card I could find which claimed to be an AGP 3.0 card was actually a universal 1.5V AGP 3.0 card. And every motherboard which claimed to be an AGP 3.0 motherboard turned out to be a universal 1.5V AGP 3.0 motherboard. It makes sense, if you think about it, because if anyone actually shipped a consumer-oriented product which supported only 0.8 volts, they would end up with lots of confused customers and a support nightmare. In the consumer market, you'd have to be crazy to ship a 0.8 volt only product.
Power consumption
This section needs expansion. You can help by adding to it. (October 2011)
Actual power supplied by an AGP slot depends upon the card used. The maximum current drawn from the various rails is given in the specifications for the various versions. For example, if maximum current is drawn from all supplies and all voltages are at their specified upper limits,[16]:95 an AGP3.0 slot can supply up to 48.25watts; this figure can be used to specify a power supply conservatively, but in practice a card is unlikely ever to draw more than 40W from the slot, with many using less. AGP Pro provides additional power up to 110W. Many AGP cards had additional power connectors to supply them with more power than the slot could provide.
Protocol
An AGP bus is a superset of a 66MHz conventional PCI bus and, immediately after reset, follows the same protocol. The card must act as a PCI target, and optionally may act as a PCI master. (AGP 2.0 added a "fast writes" extension which allows PCI writes from the motherboard to the card to transfer data at higher speed.)
After the card is initialized using PCI transactions, AGP transactions are permitted. For these, the card is always the AGP master and the motherboard is always the AGP target. The card queues multiple requests which correspond to the PCI address phase, and the motherboard schedules the corresponding data phases later. An important part of initialization is telling the card the maximum number of outstanding AGP requests which may be queued at a given time.
AGP requests are similar to PCI memory read and write requests, but use a different encoding on command lines C/BE[3:0] and are always 8-byte aligned; their starting address and length are always multiples of 8 bytes (64 bits). The three low-order bits of the address are used instead to communicate the length of the request.
Whenever the PCI GNT# signal is asserted, granting the bus to the card, three additional status bits ST[2:0] indicate the type of transfer to be performed next. If the bits are 0xx, a previously queued AGP transaction's data is to be transferred; if the three bits are 111, the card may begin a PCI transaction or (if sideband addressing is not in use) queue a request in-band using PIPE#.
AGP command codes
Like PCI, each AGP transaction begins with an address phase, communicating an address and 4-bit command code. The possible commands are different from PCI, however:
000p
Read
Read 8×(AD[2:0]+1) = 8, 16, 24, ..., 64 bytes. The least significant bit p is 0 for low-priority, 1 for high.
001x
(reserved):
010p
Write
Write 8×(AD[2:0]+1) = 8–64 bytes.
011x
(reserved):
100p
Long read
Read 32×(AD[2:0]+1) = 32, 64, 96, ..., 256 bytes. This is the same as a read request, but the length is multiplied by four.
1010
Flush
Force previously written data to memory, for synchronization. This acts as a low-priority read, taking a queue slot and returning 8 bytes of random data to indicate completion. The address and length supplied with this command are ignored.
1011
(reserved):
1100
Fence
This acts as a memory fence, requiring that all earlier AGP requests complete before any following requests. Ordinarily, for increased performance, AGP uses a very weak consistency model, and allows a later write to pass an earlier read. (E.g. after sending "write 1, write 2, read, write 3, write 4" requests, all to the same address, the read may return any value from 2 to 4. Only returning 1 is forbidden, as writes must complete before following reads.) This operation does not require any queue slots.
1101
Dual address cycle
When making a request to an address above 232, this is used to indicate that a second address cycle will follow with additional address bits. This operates like a regular PCI dual address cycle; it is accompanied by the low-order 32 bits of the address (and the length), and the following cycle includes the high 32 address bits and the desired command. The two cycles make one request, and take only one slot in the request queue. This request code is not used with side-band addressing.
111x
(reserved):
AGP 3.0 dropped high-priority requests and the long read commands, as they were little used. It also mandated side-band addressing, thus dropping the dual address cycle, leaving only four request types: low-priority read (0000), low-priority write (0100), flush (1010) and fence (1100).
In-band AGP requests using PIPE#
To queue a request in-band, the card must request the bus using the standard PCI REQ# signal, and receive GNT# plus bus status ST[2:0] equal to 111. Then, instead of asserting FRAME# to begin a PCI transaction, the card asserts the PIPE# signal while driving the AGP command, address, and length on the C/BE[3:0], AD[31:3] and AD[2:0] lines, respectively. (If the address is 64 bits, a dual address cycle similar to PCI is used.) For every cycle that PIPE# is asserted, the card sends another request without waiting for acknowledgement from the motherboard, up to the configured maximum queue depth. The last cycle is marked by deasserting REQ#, and PIPE# is deasserted on the following idle cycle.
Side-band AGP requests using SBA[7:0]
If side-band addressing is supported and configured, the PIPE# signal is not used. (And the signal is re-used for another purpose in the AGP 3.0 protocol, which requires side-band addressing.) Instead, requests are broken into 16-bit pieces which are sent as two bytes across the SBA bus. There is no need for the card to ask permission from the motherboard; a new request may be sent at any time as long as the number of outstanding requests is within the configured maximum queue depth. The possible values are:
0aaa aaaa aaaa alll
Queue a request with the given low-order address bits A[14:3] and length 8×(L[2:0]+1). The command and high-order bits are as previously specified. Any number of requests may be queued by sending only this pattern, as long as the command and higher address bits remain the same.
10cc ccra aaaa aaaa
Use command C[3:0] and address bits A[23:15] for future requests. (Bit R is reserved.) This does not queue a request, but sets values that will be used in all future queued requests.
110r aaaa aaaa aaaa
Use address bits A[35:24] for future requests.
1110 aaaa aaaa aaaa
Use address bits A[47:36] for future requests.
1111 0xxx, 1111 10xx, 1111 110x
Reserved, do not use.
1111 1110
Synchronization pattern used when starting the SBA bus after an idle period.[13]:68[15]:163
1111 1111
No operation; no request. At AGP 1× speed, this may be sent as a single byte and a following 16-bit side-band request started one cycle later. At AGP 2× and higher speeds, all side-band requests, including this NOP, are 16 bits long.
Sideband address bytes are sent at the same rate as data transfers, up to 8× the 66MHz basic bus clock. Sideband addressing has the advantage that it mostly eliminates the need for turnaround cycles on the AD bus between transfers, in the usual case when read operations greatly outnumber writes.
AGP responses
While asserting GNT#, the motherboard may instead indicate via the ST bits that a data phase for a queued request will be performed next. There are four queues: two priorities (low- and high-priority) for each of reads and writes, and each is processed in order. Obviously, the motherboard will attempt to complete high-priority requests first, but there is no limit on the number of low-priority responses which may be delivered while the high-priority request is processed.
For each cycle when the GNT# is asserted and the status bits have the value 00p, a read response of the indicated priority is scheduled to be returned. At the next available opportunity (typically the next clock cycle), the motherboard will assert TRDY# (target ready) and begin transferring the response to the oldest request in the indicated read queue. (Other PCI bus signals like FRAME#, DEVSEL# and IRDY# remain deasserted.) Up to four clock cycles worth of data (16 bytes at AGP 1× or 128 bytes at AGP 8×) are transferred without waiting for acknowledgement from the card. If the response is longer than that, both the card and motherboard must indicate their ability to continue on the third cycle by asserting IRDY# (initiator ready) and TRDY#, respectively. If either one does not, wait states will be inserted until two cycles after they both do. (The value of IRDY# and TRDY# at other times is irrelevant and they are usually deasserted.)
The C/BE# byte enable lines may be ignored during read responses, but are held asserted (all bytes valid) by the motherboard.
The card may also assert the RBF# (read buffer full) signal to indicate that it is temporarily unable to receive more low-priority read responses. The motherboard will refrain from scheduling any more low-priority read responses. The card must still be able to receive the end of the current response, and the first four-cycle block of the following one if scheduled, plus any high-priority responses it has requested.
For each cycle when GNT# is asserted and the status bits have the value 01p, write data is scheduled to be sent across the bus. At the next available opportunity (typically the next clock cycle), the card will assert IRDY# (initiator ready) and begin transferring the data portion of the oldest request in the indicated write queue. If the data is longer than four clock cycles, the motherboard will indicate its ability to continue by asserting TRDY# on the third cycle. Unlike reads, there is no provision for the card to delay the write; if it didn't have the data ready to send, it shouldn't have queued the request.
The C/BE# lines are used with write data, and may be used by the card to select which bytes should be written to memory.
The multiplier in AGP 2×, 4× and 8× indicates the number of data transfers across the bus during each 66MHz clock cycle. Such transfers use source synchronous clocking with a "strobe" signal (AD_STB[0], AD_STB[1], and SB_STB) generated by the data source. AGP 4× adds complementary strobe signals.
Because AGP transactions may be as short as two transfers, at AGP 4× and 8× speeds it is possible for a request to complete in the middle of a clock cycle. In such a case, the cycle is padded with dummy data transfers (with the C/BE# byte enable lines held deasserted).
Connector pinout
The AGP connector contains almost all PCI signals, plus several additions. The connector has 66 contacts on each side, although 4 are removed for each keying notch. Pin1 is closest to the I/O bracket, and the B and A sides are as in the table, looking down at the motherboard connector.
Contacts are spaced at 1mm intervals, however they are arranged in two staggered vertical rows so that there is 2mm space between pins in each row. Odd-numbered A-side contacts, and even-numbered B-side contacts are in the lower row (1.0 to 3.5mm from the card edge). The others are in the upper row (3.7 to 6.0mm from the card edge).
Accelerated Graphics Port connector pinout[13]:95[15]:231–3[16]:50
Pin
Side B
Side A
Comments
1
OVERCNT#
+12V
USB port overcurrent warning
2
+5V
TYPEDET#
Pulled low by card to indicate 1.5V (AGP 2.0 4x) ability
3
+5V
GC_DET#
Pulled low by card to indicate 0.8V (AGP 3.0 8x) ability
4
USB+
USB−
USB pins for pass through to monitor
5
Ground
Ground
6
INTB#
INTA#
Interrupt lines (open-drain)
7
CLK
RST#
66MHz clock, Bus reset
8
REQ#
GNT#
Bus request from card, and grant from motherboard
9
+3.3V
+3.3V
10
ST[0]
ST[1]
AGP status (valid while GNT# low)
11
ST[2]
MB_DET#
Pulled low by motherboard to indicate 0.8V (AGP 3.0 8x) ability
12
RBF#
PIPE#
DBI_HI
Read buffer full, Pipeline request, Data bus inversion[31:16]
13
Ground
Ground
14
DBI_LO
WBF#
Data bus inversion [15:0], Write buffer full
15
SBA[0]
SBA[1]
Sideband address bus
16
+3.3V
+3.3V
17
SBA[2]
SBA[3]
18
SB_STB
SB_STB#
19
Ground
Ground
20
SBA[4]
SBA[5]
21
SBA[6]
SBA[7]
22
Reserved
Reserved
Key notch for 3.3V AGP cards
23
Ground
Ground
24
+3.3V aux
Reserved
25
+3.3V
+3.3V
26
AD[31]
AD[30]
Address/data bus (upper half)
27
AD[29]
AD[28]
28
+3.3V
+3.3V
29
AD[27]
AD[26]
30
AD[25]
AD[24]
31
Ground
Ground
32
AD_STB[1]
AD_STB[1]#
33
AD[23]
C/BE[3]#
34
Vddq
Vddq
35
AD[21]
AD[22]
36
AD[19]
AD[20]
37
Ground
Ground
38
AD[17]
AD[18]
39
C/BE[2]#
AD[16]
40
Vddq
Vddq
3.3 or 1.5V
41
IRDY#
FRAME#
Initiator ready, Transfer in progress
42
+3.3V aux
Reserved
Key notch for 1.5V AGP cards
43
Ground
Ground
44
Reserved
Reserved
45
+3.3V
+3.3V
46
DEVSEL#
TRDY#
Target selected, Target ready
47
Vddq
STOP#
Target requests halt
48
PERR#
PME#
Parity error, Power management event (optional)
49
Ground
Ground
50
SERR#
PAR
System error, Even parity for (1x) PCI transactions only
51
C/BE[1]#
AD[15]
Address/data bus (lower half)
52
Vddq
Vddq
53
AD[14]
AD[13]
54
AD[12]
AD[11]
55
Ground
Ground
56
AD[10]
AD[9]
57
AD[8]
C/BE[0]#
58
Vddq
Vddq
59
AD_STB[0]
AD_STB[0]#
60
AD[7]
AD[6]
61
Ground
Ground
62
AD[5]
AD[4]
63
AD[3]
AD[2]
64
Vddq
Vddq
65
AD[1]
AD[0]
66
Vregcg
Vrefgc
I/O reference voltages
Legend
Ground pin
Zero volt reference
Power pin
Supplies power to the AGP card
Output pin
Driven by the AGP card, received by the motherboard
Initiator output
Driven by the master/initiator, received by the target
I/O signal
May be driven by initiator or target, depending on operation
Target output
Driven by the target, received by the initiator/master
Input
Driven by the motherboard, received by the AGP card
↑ The AGP Pro specifications imply a maximum of 25W.
Related Research Articles
In computer architecture, a bus is a communication system that transfers data between components inside a computer, or between computers. This expression covers all related hardware components and software, including communication protocols.
The Extended Industry Standard Architecture is a bus standard for IBM PC compatible computers. It was announced in September 1988 by a consortium of PC clone vendors as an alternative to IBM's proprietary Micro Channel architecture (MCA) in its PS/2 series.
Industry Standard Architecture (ISA) is the 16-bit internal bus of IBM PC/AT and similar computers based on the Intel 80286 and its immediate successors during the 1980s. The bus was (largely) backward compatible with the 8-bit bus of the 8088-based IBM PC, including the IBM PC/XT as well as IBM PC compatibles.
A motherboard is the main printed circuit board (PCB) in general-purpose computers and other expandable systems. It holds and allows communication between many of the crucial electronic components of a system, such as the central processing unit (CPU) and memory, and provides connectors for other peripherals. Unlike a backplane, a motherboard usually contains significant sub-systems, such as the central processor, the chipset's input/output and memory controllers, interface connectors, and other components integrated for general use.
Peripheral Component Interconnect (PCI) is a local computer bus for attaching hardware devices in a computer and is part of the PCI Local Bus standard. The PCI bus supports the functions found on a processor bus but in a standardized format that is independent of any given processor's native bus. Devices connected to the PCI bus appear to a bus master to be connected directly to its own bus and are assigned addresses in the processor's address space. It is a parallel bus, synchronous to a single bus clock. Attached devices can take either the form of an integrated circuit fitted onto the motherboard or an expansion card that fits into a slot. The PCI Local Bus was first implemented in IBM PC compatibles, where it displaced the combination of several slow Industry Standard Architecture (ISA) slots and one fast VESA Local Bus (VLB) slot as the bus configuration. It has subsequently been adopted for other computer types. Typical PCI cards used in PCs include: network cards, sound cards, modems, extra ports such as Universal Serial Bus (USB) or serial, TV tuner cards and hard disk drive host adapters. PCI video cards replaced ISA and VLB cards until rising bandwidth needs outgrew the abilities of PCI. The preferred interface for video cards then became Accelerated Graphics Port (AGP), a superset of PCI, before giving way to PCI Express.
The VESA Local Bus is a short-lived expansion bus introduced during the i486 generation of x86 IBM-compatible personal computers. Created by VESA, the VESA Local Bus worked alongside the then-dominant ISA bus to provide a standardized high-speed conduit intended primarily to accelerate video (graphics) operations. VLB provides a standardized fast path that add-in (video) card makers could tap for greatly accelerated memory-mapped I/O and DMA, while still using the familiar ISA bus to handle basic device duties such as interrupts and port-mapped I/O. Some high-end 386DX motherboards also had a VL-Bus slot.
In computing, an expansion card is a printed circuit board that can be inserted into an electrical connector, or expansion slot on a computer's motherboard to add functionality to a computer system. Sometimes the design of the computer's case and motherboard involves placing most of these slots onto a separate, removable card. Typically such cards are referred to as a riser card in part because they project upward from the board and allow expansion cards to be placed above and parallel to the motherboard.
A graphics card is a computer expansion card that generates a feed of graphics output to a display device such as a monitor. Graphics cards are sometimes called discrete or dedicated graphics cards to emphasize their distinction to an integrated graphics processor on the motherboard or the central processing unit (CPU). A graphics processing unit (GPU) that performs the necessary computations is the main component in a graphics card, but the acronym "GPU" is sometimes also used to erroneously refer to the graphics card as a whole.
HyperTransport (HT), formerly known as Lightning Data Transport, is a technology for interconnection of computer processors. It is a bidirectional serial/parallel high-bandwidth, low-latency point-to-point link that was introduced on April 2, 2001. The HyperTransport Consortium is in charge of promoting and developing HyperTransport technology.
PCI Express, officially abbreviated as PCIe or PCI-e, is a high-speed serial computer expansion bus standard, designed to replace the older PCI, PCI-X and AGP bus standards. It is the common motherboard interface for personal computers' graphics cards, capture cards, sound cards, hard disk drive host adapters, SSDs, Wi-Fi, and Ethernet hardware connections. PCIe has numerous improvements over the older standards, including higher maximum system bus throughput, lower I/O pin count and smaller physical footprint, better performance scaling for bus devices, a more detailed error detection and reporting mechanism, and native hot-swap functionality. More recent revisions of the PCIe standard provide hardware support for I/O virtualization.
In a computer system, a chipset is a set of electronic components on one or more integrated circuits that manages the data flow between the processor, memory and peripherals. The chipset is usually found on the motherboard of computers. Chipsets are usually designed to work with a specific family of microprocessors. Because it controls communications between the processor and external devices, the chipset plays a crucial role in determining system performance. Sometimes the term "chipset" is used to describe a system on chip (SoC) used in a mobile phone.
The GeForce 6 series is the sixth generation of Nvidia's GeForce line of graphics processing units. Launched on April 14, 2004, the GeForce 6 family introduced PureVideo post-processing for video, SLI technology, and Shader Model 3.0 support.
ExpressCard, initially called NEWCARD, is an interface to connect peripheral devices to a computer, usually a laptop computer. The ExpressCard technical standard specifies the design of slots built into the computer and of expansion cards to insert in the slots. The cards contain electronic circuits and sometimes connectors for external devices. The ExpressCard standard replaces the PC Card standards.
PCI-X, short for Peripheral Component Interconnect eXtended, is a computer bus and expansion card standard that enhances the 32-bit PCI local bus for higher bandwidth demanded mostly by servers and workstations. It uses a modified protocol to support higher clock speeds, but is otherwise similar in electrical implementation. PCI-X 2.0 added speeds up to 533 MHz, with a reduction in electrical signal levels.
PCI configuration space is the underlying way that the Conventional PCI, PCI-X and PCI Express perform auto configuration of the cards inserted into their bus.
The Low Pin Count (LPC) bus is a computer bus used on IBM-compatible personal computers to connect low-bandwidth devices to the CPU, such as the BIOS ROM, "legacy" I/O devices, and Trusted Platform Module (TPM). "Legacy" I/O devices usually include serial and parallel ports, PS/2 keyboard, PS/2 mouse, and floppy disk controller.
The AMD 700 chipset series is a set of chipsets designed by ATI for AMD Phenom processors to be sold under the AMD brand. Several members were launched in the end of 2007 and the first half of 2008, others launched throughout the rest of 2008.
Serial Digital Video Out (SDVO) is a proprietary Intel technology introduced with their 9xx-series of motherboard chipsets.
Apollo VP3 is a x86 based Socket 7 chipset which was manufactured by VIA Technologies and was launched in 1997. On its time Apollo VP3 was a high performance, cost effective, and energy efficient chipset. It offered AGP support for Socket 7 processors which was not supported at that moment by Intel, SiS and ALi chipsets. In November 1997 FIC released motherboard PA-2012, which uses Apollo VP3 and has AGP bus. This was the first Socket 7 motherboard supporting AGP.
Interfaces are listed by their speed in the (roughly) ascending order, so the interface at the end of each section should be the fastest. Category
This page is based on this Wikipedia article Text is available under the CC BY-SA 4.0 license; additional terms may apply. Images, videos and audio are available under their respective licenses.
