The SPARC64 V (Zeus) is a SPARC V9microprocessor designed by Fujitsu.[1] The SPARC64 V was the basis for a series of successive processors designed for servers, and later, supercomputers.
The servers series are the SPARC64 V+, VI, VI+, VII, VII+, X, X+ and XII. The SPARC64 VI and its successors up to the VII+ were used in the Fujitsu and Sun (later Oracle) SPARC Enterprise M-Series servers. In addition to servers, a version of the SPARC64 VII was also used in the commercially available Fujitsu FX1 supercomputer. As of October 2017, the SPARC64 XII is the latest server processor, and it is used in the Fujitsu and Oracle M12 servers.
The supercomputer series was based on the SPARC64 VII, and are the SPARC64 VIIfx, IXfx, and XIfx. The SPARC64 VIIIfx was used in the K computer, and the SPARC64 IXfx in the commercially available PRIMEHPC FX10. As of July 2016, the SPARC64 XIfx is the latest supercomputer processor, and it is used in the Fujitsu PRIMEHPC FX100 supercomputer.
History
In the late 1990s, HAL Computer Systems, a subsidiary of Fujitsu, was designing a successor to the SPARC64 GP as the SPARC64 V. First announced at Microprocessor Forum 1999, the HAL SPARC64 V would have operated 1GHz and had a wide superscalar organization with superspeculation, an L1 instruction trace cache, a small but very fast 8KB L1 data cache, and separate L2 caches for instructions and data. It was designed in Fujitsu's CS85 process, a 0.17μm CMOS process with six levels of copper interconnect; and would have consisted of 65 million transistors on a 380mm2 die. Originally scheduled for a late 2001 release in Fujitsu GranPower servers, it was canceled in mid-2001 when HAL was closed by Fujitsu, and replaced by a Fujitsu design.[2]
The first Fujitsu SPARC64 Vs were fabricated in December 2001.[3] They operated at 1.1 to 1.35GHz. Fujitsu's 2003 SPARC64 roadmap showed that the company planned a 1.62GHz version for release in late 2003 or early 2004, but it was canceled in favor of the SPARC64 V+.[4] The SPARC64 V was used by Fujitsu in their PRIMEPOWER servers.
The SPARC64 V was first presented at Microprocessor Forum 2002.[5] At introduction, it had the highest clock frequency of both SPARC and 64-bit server processors in production; and the highest SPEC rating of any SPARC processor.[5]
The SPARC64 V fetches up to eight instructions from the instruction cache during the first stage and places them into a 48-entry instruction buffer. In the next stage, four instructions are taken from this buffer, decoded and issued to the appropriate reserve stations. The SPARC64 V has six reserve stations, two that serve the integer units, one for the address generators, two for the floating-point units, and one for branch instructions. Each integer, address generator and floating-point unit has an eight-entry reserve station. Each reserve station can dispatch an instruction to its execution unit. Which instruction is dispatched firstly depends on operand availability and then its age. Older instructions are given higher priority than newer ones. The reserve stations can dispatch instructions speculatively (speculative dispatch). That is, instructions can be dispatched to the execution units even when their operands are not yet available but will be when execution begins. During stage six, up to six instructions are dispatched.
Register read
The register files are read during stage seven. The SPARC architecture has separate register files for integer and floating-point instructions. The integer register file has eight register windows. The JWR (Joint Work Register) contains 64 entries and has eight read ports and two write ports. The JWR contains a subset of the eight register windows, the previous, current and next register windows. Its purpose is reduce the size of register file so that the microprocessor can operate at higher clock frequencies. The floating-point register file contains 64 entries and has six read ports and two write ports.
Execution
Execution begins during stage nine. There are six execution units, two for integer, two for loads and stores, and two for floating-point.[7] The two integer execution units are designated EXA and EXB. Both have an arithmetic logic unit (ALU) and a shift unit, but only EXA has multiply and divide units. Loads and stores are executed by two address generators (AGs) designated AGA and AGB. These are simple ALUs used to calculate virtual addresses.
The two floating-point units (FPUs) are designated FLA and FLB. Each FPU contains an adder and a multiplier, but only FLA has a graphics unit attached. They execute add, subtract, multiply, divide, square root and multiply–add instructions. Unlike its successor SPARC64 VI, the SPARC64 V performs the multiply–add with separate multiplication and addition operations, thus with up to two rounding errors.[8] The graphics unit executes Visual Instruction Set (VIS) instructions, a set of single instruction, multiple data (SIMD) instructions. All instructions are pipelined except for divide and square root, which are executed using iterative algorithms. The FMA instruction is implemented by reading three operands from the operand register, multiplying two of the operands, forwarding the result and the third operand to the adder, and adding them to produce the final result.
Results from the execution units and loads are not written to the register file. To maintain program order, they are written to update buffers, where they reside until committed. The SPARC64 V has separate update buffers for integer and floating-point units. Both have 32 entries each. The integer register has eight read ports and four write ports. Half of the write ports are used for results from the integer execution units and the other half by data returned by loads. The floating-point update buffer has six read ports and four write ports.
Commit takes place during stage ten at the earliest. The SPARC64 V can commit up to four instructions per cycle. During stage eleven, results are written to the register file, where it becomes visible to software.[9]
Cache
The SPARC64 V has two-level cache hierarchy. The first level consists of two caches, an instruction cache and a data cache. The second level consists of an on-die unified cache.
The level 1 (L1) caches each have a capacity of 128KB. They are both two-way set associative and have 64-byte line size. They are virtually indexed and physically tagged. The instruction cache is accessed via a 256-bit bus. The data cache is accessed with two 128-bit buses. The data cache consists of eight banks separated by 32-bit boundaries. It uses a write-back policy. The data cache writes to the L2 cache with its own 128-bit unidirectional bus.
The second level cache has a capacity of 1 or 2MB and the set associativity depends on the capacity.
System bus
The microprocessor has a 128-bit system bus that operates at 260MHz. The bus can operate in two modes, single-data rate (SDR) or double-data (DDR) rate, yielding a peak bandwidth of 4.16 or 8.32GB/s, respectively.
At 1.3GHz, the SPARC64 V has a power dissipation of 34.7 W.[10] The Fujitsu PrimePower servers that use the SPARC64 V supply a slightly higher voltage the microprocessor to enable it to operate at 1.35GHz. The increased power supply voltage and operating frequency increased the power dissipation to ~45 W.[12]
The SPARC64 V+, code-named "Olympus-B", is a further development of the SPARC64 V. Improvements over the SPARC64 V included higher clock frequencies of 1.82–2.16GHz and a larger 3 or 4MB L2 cache.[1]
The first SPARC64 V+, a 1.89GHz version, was shipped in September 2004 in the Fujitsu PrimePower 650 and 850. In December 2004, a 1.82GHz version was shipped in the PrimePower 2500. These versions have a 3MB L2 cache.[13] In February 2006, four versions were introduced: 1.65 and 1.98GHz versions with 3MB L2 caches shipped in the PrimePower 250 and 450; and 2.08 and 2.16GHz versions with 4MB L2 caches shipped in mid-range and high-end models.[14]
It contained approximately 400 million transistors on an 18.46mm by 15.94mm die for an area of 294.25mm2. It was fabricated in a 90nm CMOS process with ten levels of copper interconnect.[6]
The SPARC64 VI, code-named Olympus-C, is a two-core processor (the first multi-core SPARC64 processor) which succeeded the SPARC64 V+. It is fabricated by Fujitsu in a 90nm, 10-layer copper, CMOS silicon on insulator (SOI) process, which enabled two cores and an L2 cache to be integrated on a die. Each core is a modified SPARC64 V+ processor. One of the main improvements is the addition of two-way coarse-grained multi-threading (CMT), which Fujitsu called vertical multi-threading (VMT). In CMT, which thread is executed is determined by time-sharing, or if the thread is executing a long-latency operation, then execution is switched to the other thread.[15] The addition of CMT required duplication of the program counter and the control, integer, and floating-point registers so there is one set of each for every thread. A floating-point fused multiply-add (FMA) instruction was also added, the first SPARC processor to do so.[8]
The cores share a 6MB on-die unified L2 cache. The L2 cache is 12-way set associative and has 256-byte lines. The cache is accessed via two unidirectional buses, a 256-bit read bus and a 128-bit write bus. The SPARC64 VI has a new system bus, the Jupiter Bus. The SPARC64 VI consisted of 540 million transistors. The die measures 20.38mm by 20.67mm (421.25mm2).
The SPARC64 VI was originally to have been introduced in mid-2004 in Fujitsu's PrimePower servers. Development of the PrimerPowers were canceled after Fujitsu and Sun Microsystems announced in June 2004 that they would collaborate on new servers called the Advanced Product Line (APL). These servers were scheduled to be introduced in mid-2006, but were delayed until April 2007, when they were introduced as the SPARC Enterprise. The SPARC64 VI processors featured in the SPARC Enterprise at its announcement were a 2.15GHz version with a 5MB L2 cache, and 2.28 and 2.4GHz versions with 6MB L2 caches.[16]
SPARC64 VII
The SPARC64 VII (previously called the SPARC64 VI+),[17] code-named Jupiter,[18] is a further development of the SPARC64 VI announced in July 2008.[18] It is a quad-core microprocessor. Each core is capable of two-way simultaneous multithreading (SMT), which replaces two-way coarse-grained multithreading, termed vertical multithreading (VMT) by Fujitsu. Thus, it can execute eight threads simultaneously.[19] Other changes include more RAS features; the integer register file is now protected by ECC, and the number of error checkers has been increased to around 3,400. It consists of 600 million transistors, is 21.31mm×20.86mm (444.63mm2) large, and is fabricated by Fujitsu in its 65nm CMOS, copper interconnect process.
The SPARC64 VII was featured in the SPARC Enterprise. It is socket-compatible with its predecessor, the SPARC64 VI, and is field-upgradeable. SPARC64 VIIs could coexist, whilst operating at their native clock frequency, alongside SPARC64 VIs.[20] The first versions of the SPARC64 VII were a 2.4GHz version with a 5MB L2 cache used in the SPARC Enterprise M4000 and M5000, and a 2.52GHz version with a 6MB L2 cache.[18] On 28 October 2008, a 2.52GHz version with a 5MB L2 cache was introduced in the SPARC Enterprise M3000.[21] On 13 October 2009, Fujitsu and Sun introduced new versions of the SPARC64 VII (code-named Jupiter+),[22] a 2.53GHz version with a 5.5MB L2 cache for the M4000 and M5000, and a 2.88GHz version with a 6MB L2 cache for the M8000 and M9000.[23] On 12 January 2010, a 2.75GHz version with a 5MB L2 cache was introduced in the M3000.[24]
SPARC64 VII+
The SPARC64 VII+ (Jupiter-E),[25] referred to as the M3 by Oracle,[25] is a further development of the SPARC64 VII. The clock frequency was increased up to 3GHz and the L2 cache size was doubled to 12MB. This version was announced on 2 December 2010 for the high-end SPARC Enterprise M8000 and M9000 servers.[26] These improvements resulted in an approximately 20% increase to overall performance. A 2.66GHz version was for mid-range M4000 and M5000 models.[25] On 12 April 2011, a 2.86GHz version with two or four cores and a 5.5MB L2 cache was announced for the low-end M3000.[27][25] The VII+ is socket-compatible with its predecessor, the VII. Existing high-end SPARC Enterprise M-Series servers are able to upgrade to the VII+ processors in the field.[28]
The SPARC64 VIIIfx (Venus) is an eight-core processor based on the SPARC64 VII designed for high-performance computing (HPC).[29] As a result, the VIIIfx did not succeed the VII, but existed concurrently with it. It consists of 760 million transistors, measures 22.7mm by 22.6 (513.02mm2;), is fabricated in Fujitu's 45 nm CMOS process with copper interconnects, and has 1,271 I/O pins. The VIIIfx has a peak performance at 2GHz of 128GFLOPS and a typical power consumption of 58W at 30°C for an efficiency of 2.2GFLOPS/W. The VIIIfx has four integrated memory controllers for a total of eight memory channels. It connects to 64GB of DDR3 SDRAM and has a peak memory bandwidth of 64GB/s.[30]
History
The VIIIfx was developed for the Next-Generation Supercomputer Project (also called Kei Soku Keisenki and Project Keisoku) initiated by Japan's Ministry of Education, Culture, Sports, Science and Technology in January 2006. The project aimed to produce the world's fastest supercomputer with performance of over 10PFLOPS by March 2011. The companies contracted to develop the supercomputer were Fujitsu, Hitachi, and NEC. The supercomputer was originally envisioned to have a hybrid architecture containing scalar and vector processors. The Fujitsu-designed VIIIfx was to have been the scalar processor, with the vector processor to have been jointly designed by Hitachi and NEC. However, due to the Financial crisis of 2007–2008, Hitachi and NEC announced in May 2009 that they would leave the project because manufacturing the hardware they were responsible for would result in financial losses for them. Afterwards, Fujitsu redesigned the supercomputer to use the VIIIfx as its only processor type.
By 2010, the supercomputer that would be built by the project was named the K computer. Located at the RIKEN's Advanced Institute for Computational Science (AICS) in Kobe, Japan;[31][32][33] it obtains its performance from 88,128 VIIIfx processors. In June 2011, the TOP500 Project Committee announced that the K computer (still incomplete with only 68,544 processors) topped the LINPACK benchmark at 8.162PFLOPS, realizing 93% of its peak performance, making it the fastest supercomputer in the world at that time.[32][34][35][36]
Description
The VIIIfx core is based on that of the SPARC64 VII with numerous modifications for HPC, namely High Performance Computing-Arithmetic Computational Extensions (HPC-ACE) a Fujitsu-designed extension to the SPARC V9 architecture. The front-end had coarse-grained multi-threading removed, the L1 instruction cache halved in size to 32KB; and the number of branch target address cache (BTAC) entries reduced to 1,024 from 8,192, and its associativity reduced to two from eight; and an extra pipeline stage was inserted before the instruction decoder. This stage accommodated the greater number of integer and floating-point registers defined by HPC-ACE. The SPARC V9 architecture was designed to have only 32 integer and 32 floating-point number registers. The SPARC V9 instruction encoding limited the number of registers specifiable to 32. To specify the extra registers, HPC-ACE has a "prefix" instruction that would immediately follow one or two SPARC V9 instructions. The prefix instruction contained (primarily) the portions of the register numbers that could not fit within a SPARC V9 instruction. This extra pipeline stage was where up to four SPARC V9 instructions were combined with up to two prefix instructions in the preceding stage. The combined instructions were then decoded in the next pipeline stage.
The back-end was also heavily modified. The number of reservation station entries for branch and integer instructions were reduced to six and ten, respectively. Both the integer and floating-point register files had registers added to them: the integer register file gained 32, and there were a total of 256 floating-point registers. The extra integer registers are not part of the register windows defined by SPARC V9, but are always accessible via the prefix instruction; and the 256 floating-point registers could be used by both scalar floating-point instructions and by both integer and floating-point SIMD instructions. An extra pipeline stage was added to the beginning of the floating-point execution pipeline to access the larger floating-point register file. The 128-bit SIMD instructions from HPC-ACE were implemented by adding two extra floating-point units for a total of four. SIMD execution can perform up four single- or double-precision fused-multiply-add operations (eight FLOPs) per cycle. The number of load queue entries was increased to 20 from 16, and the L1 data cache was halved in size to 32KB. The number of commit stack entries, which determined the number of instructions that could be in-flight in the back-end, was reduced to 48 from 64.
The SPARC64 IXfx is an improved version of the SPARC64 VIIIfx designed by Fujitsu and LSI[37] first revealed in the announcement of the PRIMEHPC FX10 supercomputer on 7 November 2011.[38] It, along with the PRIMEHPC FX10, is a commercialization of the technologies that first appeared in the VIIIfx and K computer. Compared to the VIIIfx, organizational improvements included doubling the number of cores was to 16, doubling the amount of shared L2 cache to 12MB, and increasing peak DDR3 SDRAM memory bandwidth to 85GB/s. The IXfx operates at 1.848GHz, has a peak performance of 236.5GFLOPS, and consumes 110W for a power efficiency of more than 2GFLOPS per watt.[39][37] It consisted of 1 billion transistors and was implemented in a 40nm CMOS process with copper interconnects.[40]
SPARC64 X
The SPARC64 X is a 16-core server microprocessor announced in 2012 and used in Fujitsu's M10 servers (which are also marketed by Oracle). The SPARC64 X is based on the SPARC64 VII+ with significant enhancements to its core and chip organization. The cores were improved by the inclusion of a pattern history table for branch prediction, speculative execution of loads, more execution units, support for the HPC-ACE extension (originally from the SPARC64 VIIIfx), deeper pipeline for a 3.0GHz clock frequency, and accelerators for cryptography, database, and decimal floating-point number arithmetic and conversion functions. The 16 cores share a unified, 24MB, 24-way set-associative L2 cache. Chip organization improvements include four integrated DDR3 SDRAM memory controllers, glueless four-way symmetrical multiprocessing, ten SERDES channels for symmetrical multiprocessing scalability to 64 sockets, and two integrated PCI Express 3.0 controllers. The SPARC64 X contains 2.95 billion transistors, measures 23.5mm by 25mm (587.5mm2), and is fabricated in a 28nm CMOS process with copper interconnects.[41][40]
SPARC64 X+
The SPARC64 X+ is an enhanced SPARC64 X processor announced in 2013. It features minor improvements to the core organization, and a higher 3.5GHz clock frequency obtained through better circuit design and layout. It contained 2.99 billion transistors, measured 24mm by 25mm (600mm2), and is fabricated in the same process as the SPARC64 X.[42][43] On 8 April 2014, 3.7GHz speed-binned parts became available in response to the introduction of new Xeon E5 and E7 models by Intel; and the impending introduction of the POWER8 by IBM.[44]
SPARC64 XIfx
Fujitsu introduced the SPARC64 XIfx in August 2014 at the Hot Chips symposium.[45] It is used in the Fujitsu PRIMEHPC FX100 supercomputer, which succeeded the PRIMEHPC FX10.[46][47] The XIfx operates at 2.2GHz and has a peak performance of 1.1TFLOPS.[48] It consists of 3.75 billion transistors and is fabricated by the Taiwan Semiconductor Manufacturing Company in its 20 nmhigh-κ metal gate (HKMG) process. The Microprocessor Report estimated the die to have an area of 500mm2; and a typical power consumption of 200W.[45]
The XIfx has 34 cores, 32 of which are compute cores used to run user applications, and 2 assistant cores used to run the operating system and other system services. The delegation of user applications and operating system to dedicated cores improves performance by ensuring that the private caches of the compute cores are not shared with or disrupted by non-application instructions and data. The 34 cores are further organized into two Core Memory Groups (CMGs), each consisting of 16 compute cores and 1 assistant core sharing a 12MB L2 unified cache. The division of the cores into CMGs enabled 34 cores to be integrated on a single die by easing the implementation of cache coherence and avoiding the need for the L2 cache to be shared between 34 cores. The two CMGs share the memory through a ccNUMA organization.
The XIfx core was based on the SPARC64 X+ with organizational improvements. The XIfx implements an improved version of the HPC-ACE extensions (HPC-ACE2), which doubled the width of the SIMD units to 256 bits and added new SIMD instructions. Compared to the SPARC64 IXfx, the XIfx has an improvement of a factor of 3.2 for double precision and 6.1 for single precision. To complement the increased width of the SIMD units, the L1 cache bandwidth was increased to 4.4TB/s.
Improvements to the SoC organization were to the memory and interconnect interfaces. The integrated memory controllers were replaced with four Hybrid Memory Cube (HMC) interfaces for decreased memory latency and improved memory bandwidth. According to the Microprocessor Report, the IXfx was the first processor to use HMCs.[45] The XIfx is connected to 32GB of memory provided by eight 4GB HMCs. The HMCs are 16-lane versions, with each lane operating at 15Gbit/s. Each CMG has two HMC interfaces, and each HMC interface is connected to two HMCs via its own ports. Each CMG has 240GB/s (120GB/s in and 120GB/s out) of memory bandwidth.
The XIfx replaced the ten SERDES channels to an external Tofu interconnect controller with a ten-port integrated controller for the second-generation Tofu2 interconnect. Tofu2 is a 6D mesh/torus network with a 25GB/s full-duplex bandwidth (12.5GB/s per direction, 125GB/s for ten ports) and an improved routing architecture.
Future
Fujitsu announced at the International Supercomputing Conference in June 2016 that its future exascale supercomputer will feature processors of its own design that implement the ARMv8 architecture. The A64FX will implement extensions to the ARMv8 architecture, equivalent to HPC-ACE2, that Fujitsu is developing with ARM Holdings.[49]
SPARC64 XII
This section needs expansion. You can help by adding to it. (January 2018)
SPARC64 XII was launched in 2017 with Fujitsu's SPARC M12 servers. It nominally features 12 cores, but just like IBM's POWER9 that was launched the same year, each of the twelve cores consists of two separate pipelines, and the only resources shared between SPARC64 XII core's pipelines are the TLB, L1 instruction cache and L2 cache, and as a result the single-threaded performance is almost unchanged from SPARC64 X. SPARC64 XII operates at up to 4.25GHz base frequency and 4.35GHz boost frequency. The size of the chip is 25.8mm × 30.8mm (795mm2), containing 5.45 billion transistors made on TSMC's 20 nm process. Each of the two pipelines of a core can fetch 8 instructions, decode 4 instructions and execute 6 instructions per cycle, and supports 4 SMT threads (for 96 threads per CPU). Each pipeline has an own 32 MB 4-way L1 data cache, and two pipelines share a 64 MB 4-way associative L1 instruction cache and a 512 MB 16-way L2 cache. SPARC64 XII is Fujitsu's first SPARC CPU with L3 cache (32 MB 16-way). The number of 8-lane PCIe 3.0 ports has been doubled to 4 per chip. Memory speed has been increased by 50% to 2400 MT/s, bringing the theoretical combined bandwidth of the 8 DDR4 channels of the chip to 153 GB/s, and the capacity per CPU is up to 1.5 TB across 24 slots. Two CPUs can be connected in a Building Block, and up to 16 Building Blocks can be connected to create a 32-CPU server with up to 48 TB of memory.[50][51]
Related Research Articles
SPARC is a reduced instruction set computer (RISC) instruction set architecture originally developed by Sun Microsystems. Its design was strongly influenced by the experimental Berkeley RISC system developed in the early 1980s. First developed in 1986 and released in 1987, SPARC was one of the most successful early commercial RISC systems, and its success led to the introduction of similar RISC designs from many vendors through the 1980s and 1990s.
The POWER5 is a microprocessor developed and fabricated by IBM. It is an improved version of the POWER4. The principal improvements are support for simultaneous multithreading (SMT) and an on-die memory controller. The POWER5 is a dual-core microprocessor, with each core supporting one physical thread and two logical threads, for a total of two physical threads and four logical threads.
SPARC64 is a microprocessor developed by HAL Computer Systems and fabricated by Fujitsu. It implements the SPARC V9 instruction set architecture (ISA), the first microprocessor to do so. SPARC64 was HAL's first microprocessor and was the first in the SPARC64 brand. It operates at 101 and 118 MHz. The SPARC64 was used exclusively by Fujitsu in their systems; the first systems, the Fujitsu HALstation Model 330 and Model 350 workstations, were formally announced in September 1995 and were introduced in October 1995, two years late. It was succeeded by the SPARC64 II in 1996.
POWER7 is a family of superscalar multi-core microprocessors based on the Power ISA 2.06 instruction set architecture released in 2010 that succeeded the POWER6 and POWER6+. POWER7 was developed by IBM at several sites including IBM's Rochester, MN; Austin, TX; Essex Junction, VT; T. J. Watson Research Center, NY; Bromont, QC and IBM Deutschland Research & Development GmbH, Böblingen, Germany laboratories. IBM announced servers based on POWER7 on 8 February 2010.
Sun Microsystems' UltraSPARC T1 microprocessor, known until its 14 November 2005 announcement by its development codename "Niagara", is a multithreading, multicore CPU. Designed to lower the energy consumption of server computers, the CPU typically uses 72 W of power at 1.4 GHz.
The R10000, code-named "T5", is a RISC microprocessor implementation of the MIPS IV instruction set architecture (ISA) developed by MIPS Technologies, Inc. (MTI), then a division of Silicon Graphics, Inc. (SGI). The chief designers are Chris Rowen and Kenneth C. Yeager. The R10000 microarchitecture is known as ANDES, an abbreviation for Architecture with Non-sequential Dynamic Execution Scheduling. The R10000 largely replaces the R8000 in the high-end and the R4400 elsewhere. MTI was a fabless semiconductor company; the R10000 was fabricated by NEC and Toshiba. Previous fabricators of MIPS microprocessors such as Integrated Device Technology (IDT) and three others did not fabricate the R10000 as it was more expensive to do so than the R4000 and R4400.
The UltraSPARC IVJaguar and follow-up UltraSPARC IV+Panther are microprocessors designed by Sun Microsystems and manufactured by Texas Instruments. They are the fourth generation of UltraSPARC microprocessors, and implement the 64-bit SPARC V9 instruction set architecture (ISA). The UltraSPARC IV was originally to be succeeded by the UltraSPARC V Millennium, which was canceled after the announcement of the Niagara, now UltraSPARC T1 microprocessor in early 2004. It was instead succeeded by the Fujitsu-designed SPARC64 VI.
The SPARC Enterprise series is a range of UNIX server computers based on the SPARC V9 architecture. It was co-developed by Sun Microsystems and Fujitsu, announced on June 1, 2004, and introduced in 2007. They were marketed and sold by Sun Microsystems, Fujitsu, and Fujitsu Siemens Computers under the common brand of "SPARC Enterprise", superseding Sun's Sun Fire and Fujitsu's PRIMEPOWER server product lines. Codename is APL.
The PA-8000 (PCX-U), code-named Onyx, is a microprocessor developed and fabricated by Hewlett-Packard (HP) that implemented the PA-RISC 2.0 instruction set architecture (ISA). It was a completely new design with no circuitry derived from previous PA-RISC microprocessors. The PA-8000 was introduced on 2 November 1995 when shipments began to members of the Precision RISC Organization (PRO). It was used exclusively by PRO members and was not sold on the merchant market. All follow-on PA-8x00 processors are based on the basic PA-8000 processor core.
The UltraSPARC III, code-named "Cheetah", is a microprocessor that implements the SPARC V9 instruction set architecture (ISA) developed by Sun Microsystems and fabricated by Texas Instruments. It was introduced in 2001 and operates at 600 to 900 MHz. It was succeeded by the UltraSPARC IV in 2004. Gary Lauterbach was the chief architect.
The UltraSPARC II, code-named "Blackbird", is a microprocessor implementation of the SPARC V9 instruction set architecture (ISA) developed by Sun Microsystems. Marc Tremblay was the chief architect. Introduced in 1997, it was further development of the UltraSPARC operating at higher clock frequencies of 250 MHz, eventually reaching 650 MHz.
The TurboSPARC is a microprocessor that implements the SPARC V8 instruction set architecture (ISA) developed by Fujitsu Microelectronics, Inc. (FMI), the United States subsidiary of the Japanese multinational information technology equipment and services company Fujitsu Limited located in San Jose, California. It was a low-end microprocessor primarily developed as an upgrade for the Sun Microsystems microSPARC-II-based SPARCstation 5 workstation. It was introduced on 30 September 1996, with a 170 MHz version priced at US$499 in quantities of 1,000. The TurboSPARC was mostly succeeded in the low-end SPARC market by the UltraSPARC IIi in late 1997, but remained available.
The IBM A2 is an open source massively multicore capable and multithreaded 64-bit Power ISA processor core designed by IBM using the Power ISA v.2.06 specification. Versions of processors based on the A2 core range from a 2.3 GHz version with 16 cores consuming 65 W to a less powerful, four core version, consuming 20 W at 1.4 GHz.
The z196 microprocessor is a chip made by IBM for their zEnterprise 196 and zEnterprise 114 mainframe computers, announced on July 22, 2010. The processor was developed over a three-year time span by IBM engineers from Poughkeepsie, New York; Austin, Texas; and Böblingen, Germany at a cost of US$1.5 billion. Manufactured at IBM's Fishkill, New York fabrication plant, the processor began shipping on September 10, 2010. IBM stated that it was the world's fastest microprocessor at the time.
The SPARC T4 is a SPARC multicore microprocessor introduced in 2011 by Oracle Corporation. The processor is designed to offer high multithreaded performance, as well as high single threaded performance from the same chip. The chip is the 4th generation processor in the T-Series family. Sun Microsystems brought the first T-Series processor to market in 2005.
The MCST R1000 is a 64-bit microprocessor developed by Moscow Center of SPARC Technologies (MCST) and fabricated by TSMC.
The PRIMEHPC FX10 is a supercomputer designed and manufactured by Fujitsu. Announced on 7 November 2011 at the Supercomputing Conference, the PRIMEHPC FX10 is an improved and commercialized version of the K computer, which was the first supercomputer to obtain more than 10 PFLOPS on the LINPACK benchmark. In its largest configuration, the PRIMEHPC FX10 has a peak performance 23.2 PFLOPS, power consumption of 22.4 MW, and a list price of US$655.4 million. It was succeeded by the PRIMEHPC FX100 with SPARC64 XIfx processors in 2015.
The zEC12 microprocessor is a chip made by IBM for their zEnterprise EC12 and zEnterprise BC12 mainframe computers, announced on August 28, 2012. It is manufactured at the East Fishkill, New York fabrication plant. The processor began shipping in the fall of 2012. IBM stated that it was the world's fastest microprocessor and is about 25% faster than its predecessor the z196.
The z13 is a microprocessor made by IBM for their z13 mainframe computers, announced on January 14, 2015. Manufactured at GlobalFoundries' East Fishkill, New York fabrication plant. IBM stated that it is the world's fastest microprocessor and is about 10% faster than its predecessor the zEC12 in general single-threaded computing, but significantly more when doing specialized tasks.
The A64FX is a 64-bit ARM architecture microprocessor designed by Fujitsu. The processor is replacing the SPARC64 V as Fujitsu's processor for supercomputer applications. It powers the Fugaku supercomputer, ranked in the TOP500 as the fastest supercomputer in the world from June of 2020, until falling to second place behind Frontier in June of 2022.
↑ Microarchitecture and Performance Analysis of a SPARC-V9 Microprocessor for Enterprise Server Systems. Ninth International Symposium on High-Performance Computer Architecture, 2003 (HPCA-9 2003). doi:10.1109/HPCA.2003.1183533.
Sakamoto, Mariko et al. (2003). "Microarchitecture and Performance Analysis of a SPARC-V9 Microprocessor for Enterprise Server Systems". Proceedings of the 9th International Symposium on High-Performance Computer Architecture. pp.141–152.
Ito, N.; Komatsu, H.; Tanamura, Y.; Yamashita, R.; Sugiyama, H.; Sugiyama, Y.; Hamamura, H. (2003). A physical design methodology for 1.3GHz SPARC 64 microprocessor. 21st International Conference on Computer Design. pp.204–210. doi:10.1109/ICCD.2003.1240896. ISBN0-7695-2025-1. ISSN1063-6404.
Ando, Hisashige; Kan, Ryuji; Tosaka, Yoshiharu; Takahisa, Keiji; Hatanaka, Kichiji (24–27 June 2008). Validation of hardware error recovery mechanisms for the SPARC64 V microprocessor. 2008 IEEE International Conference on Dependable Systems and Networks. pp.62–69. doi:10.1109/DSN.2008.4630071. ISBN978-1-4244-2397-2. ISSN1530-0889.
This page is based on this Wikipedia article Text is available under the CC BY-SA 4.0 license; additional terms may apply. Images, videos and audio are available under their respective licenses.
