Second-harmonic generation

Last updated
Energy level scheme of SHG process Energy level scheme of SHG.png
Energy level scheme of SHG process

Second-harmonic generation (SHG), also known as frequency doubling, is the lowest-order wave-wave nonlinear interaction that occurs in various systems, including optical, radio, atmospheric, and magnetohydrodynamic systems. [1] As a prototype behavior of waves, SHG is widely used, for example, in doubling laser frequencies. SHG was initially discovered as a nonlinear optical process [2] in which two photons with the same frequency interact with a nonlinear material, are "combined", and generate a new photon with twice the energy of the initial photons (equivalently, twice the frequency and half the wavelength), that conserves the coherence of the excitation. It is a special case of sum-frequency generation (2 photons), and more generally of harmonic generation.

Contents

The second-order nonlinear susceptibility of a medium characterizes its tendency to cause SHG. Second-harmonic generation, like other even-order nonlinear optical phenomena, is not allowed in media with inversion symmetry (in the leading electric dipole contribution). [3] However, effects such as the Bloch–Siegert shift (oscillation), found when two-level systems are driven at Rabi frequencies comparable to their transition frequencies, will give rise to second-harmonic generation in centro-symmetric systems. [4] [5] In addition, in non-centrosymmetric crystals belonging to crystallographic point group 432, SHG is not possible [6] and under Kleinman's conditions SHG in 422 and 622 point groups should vanish, [7] although some exceptions exist. [8]

In some cases, almost 100% of the light energy can be converted to the second-harmonic frequency. These cases typically involve intense pulsed laser beams passing through large crystals and careful alignment to obtain phase matching. In other cases, like second-harmonic imaging microscopy, only a tiny fraction of the light energy is converted to the second harmonic, but this light can nevertheless be detected with the help of optical filters.

Schematic of the SHG conversion of an excited wave in a non-linear medium.png

Generating the second harmonic, often called frequency doubling, is also a process in radio communication; it was developed early in the 20th century and has been used with frequencies in the megahertz range. It is a special case of frequency multiplication.

History

An electron (purple) is being pushed side-to-side by a sinusoidally oscillating force, i.e. the light's electric field. But because the electron is in an anharmonic potential energy environment (black curve), the electron motion is not sinusoidal. The three arrows show the Fourier series of the motion: The blue arrow corresponds to ordinary (linear) susceptibility, the green arrow corresponds to second-harmonic generation, and the red arrow corresponds to optical rectification. Electron asymmetric motion animation.gif
An electron (purple) is being pushed side-to-side by a sinusoidally oscillating force, i.e. the light's electric field. But because the electron is in an anharmonic potential energy environment (black curve), the electron motion is not sinusoidal. The three arrows show the Fourier series of the motion: The blue arrow corresponds to ordinary (linear) susceptibility, the green arrow corresponds to second-harmonic generation, and the red arrow corresponds to optical rectification.

Second-harmonic generation was first demonstrated by Peter Franken, A. E. Hill, C. W. Peters, and G. Weinreich at the University of Michigan, Ann Arbor, in 1961. [9] The demonstration was made possible by the invention of the laser, which created the required high-intensity coherent light. They focused a ruby laser with a wavelength of 694 nm into a quartz sample. They sent the output light through a spectrometer, recording the spectrum on photographic paper, which indicated the production of light at 347 nm. Famously, when published in the journal Physical Review Letters, [9] the copy editor mistook the dim spot (at 347 nm) on the photographic paper as a speck of dirt and removed it from the publication. [10] The formulation of SHG was initially described by N. Bloembergen and P. S. Pershan at Harvard in 1962. [11] In their extensive evaluation of Maxwell's equations at the planar interface between a linear and nonlinear medium, several rules for the interaction of light in non-linear media were elucidated.

Types in crystals

Critical phase-matching

Different types of second-harmonic generation phase-matching of a coherent light for strong conversion. The case of negative crystals (
n
o
>
n
e
{\displaystyle n_{o}>n_{e}}
) is considered, invert indices if positive crystal (
n
e
>
n
o
{\displaystyle n_{e}>n_{o}}
). TypeX SHG.png
Different types of second-harmonic generation phase-matching of a coherent light for strong conversion. The case of negative crystals () is considered, invert indices if positive crystal ().

Second-harmonic generation occurs in three types for critical phase-matching, [12] denoted 0, I and II. In Type 0 SHG two photons having extraordinary polarization with respect to the crystal will combine to form a single photon with double the frequency/energy and extraordinary polarization. In Type I SHG two photons having ordinary polarization with respect to the crystal will combine to form one photon with double the frequency and extraordinary polarization. In Type II SHG, two photons having orthogonal polarizations will combine to form one photon with double the frequency and ordinary polarization. For a given crystal orientation, only one of these types of SHG occurs. In general to utilise Type 0 interactions a quasi-phase-matching crystal type will be required, for example periodically poled lithium niobate (PPLN).

Non-critical phase-matching

Since phase-matching process basically means to adapt the optical indices n at ω and 2ω, it can also be done by a temperature control in some birefringent crystals, because n changes with the temperature. For instance, LBO presents a perfect phase-matching at 25 °C for a SHG excited at 1200 or 1400 nm, [13] but needs to be elevated at 200 °C for SHG with the usual laser line of 1064 nm. It is called "non-critical" because it does not depend on the crystal orientation as usual phase-matching.

Optical second-harmonic generation

Diagram of the second-harmonic generation process Second Harmonic Generation.svg
Diagram of the second-harmonic generation process

Since media with inversion symmetry are forbidden from generating second-harmonic light via the leading-order electric dipole contribution (unlike third harmonic generation), surfaces and interfaces make interesting subjects for study with SHG. In fact, second-harmonic generation and sum frequency generation discriminate against signals from the bulk, implicitly labeling them as surface specific techniques. In 1982, T. F. Heinz and Y. R. Shen explicitly demonstrated for the first time that SHG could be used as a spectroscopic technique to probe molecular monolayers adsorbed to surfaces. [14] Heinz and Shen adsorbed monolayers of laser dye rhodamine to a planar fused silica surface; the coated surface was then pumped by a nanosecond ultra-fast laser. SH light with characteristic spectra of the adsorbed molecule and its electronic transitions were measured as reflection from the surface and demonstrated a quadratic power dependence on the pump laser power.

In SHG spectroscopy, one focuses on measuring twice the incident frequency 2ω given an incoming electric field in order to reveal information about a surface. Simply (for a more in-depth derivation see below), the induced second-harmonic dipole per unit volume, , can be written as

where is known as the nonlinear susceptibility tensor and is a characteristic to the materials at the interface of study. [15] The generated and corresponding have been shown to reveal information about the orientation of molecules at a surface/interface, the interfacial analytical chemistry of surfaces, and chemical reactions at interfaces.

From planar surfaces

A depiction of the second-harmonic generation setup for measuring the orientation of phenol at the air-water interface. SHG phenol air-water.png
A depiction of the second-harmonic generation setup for measuring the orientation of phenol at the air-water interface.

Early experiments in the field demonstrated second-harmonic generation from metal surfaces. [16] Eventually, SHG was used to probe the air-water interface, allowing for detailed information about molecular orientation and ordering at one of the most ubiquitous of surfaces. [17] It can be shown that the specific elements of :

where Ns is the adsorbate density, θ is the angle that the molecular axis z makes with the surface normal Z, and is the dominating element of the nonlinear polarizability of a molecule at an interface, allow one to determine θ, given laboratory coordinates (x, y, z). [18] Using an interference SHG method to determine these elements of χ(2), the first molecular orientation measurement showed that the hydroxyl group of phenol pointed downwards into the water at the air-water interface (as expected due to the potential of hydroxyl groups to form hydrogen bonds). Additionally SHG at planar surfaces has revealed differences in pKa and rotational motions of molecules at interfaces.

From non-planar surfaces

Cartoon depicting ordered molecules at a small spherical surface. An ultrafast pump laser pumps light with frequency o which generates light at 2o from the locally non-centrosymmetric media. SHG from small sphere.png
Cartoon depicting ordered molecules at a small spherical surface. An ultrafast pump laser pumps light with frequency ω which generates light at 2ω from the locally non-centrosymmetric media.

Second-harmonic light can also be generated from surfaces that are "locally" planar, but may have inversion symmetry (centrosymmetric) on a larger scale. Specifically, recent theory has demonstrated that SHG from small spherical particles (micro- and nanometer scale) is allowed by proper treatment of Rayleigh scattering (scattering without a change in frequency from absorbed to emitted waves). [19] At the surface of a small sphere, inversion symmetry is broken, allowing for SHG and other even order harmonics to occur.

For a colloidal system of microparticles at relatively low concentrations, the total SH signal , is given by:

where is the SH electric field generated by the jth particle, and n the density of particles. [20] The SH light generated from each particle is coherent, but adds incoherently to the SH light generated by others (as long as density is low enough). Thus, SH light is only generated from the interfaces of the spheres and their environment and is independent of particle-particle interactions. It has also been shown that the second-harmonic electric field scales with the radius of the particle cubed, a3.

Besides spheres, other small particles like rods have been studied similarly by SHG. [21] Both immobilized and colloidal systems of small particles can be investigated. Recent experiments using second-harmonic generation of non-planar systems include transport kinetics across living cell membranes [22] and demonstrations of SHG in complex nanomaterials. [23]

Radiation pattern

SHG radiation pattern excited with a Gaussian beam, in a homogeneous medium (A), or at an interface between opposite polarities that is parallel to the propagation (B). Only the forward SHG is represented. SHG radiation pattern from interfaces or not.png
SHG radiation pattern excited with a Gaussian beam, in a homogeneous medium (A), or at an interface between opposite polarities that is parallel to the propagation (B). Only the forward SHG is represented.

The SHG radiation pattern generated by an exciting Gaussian beam also has a (homogeneous) 2D Gaussian profile if the nonlinear medium being excited is homogeneous (A). However, if the exciting beam is positioned at an interface between opposite polarities (± boundary, B) that is parallel to the beam propagation (see figure), the SHG will be split into two lobes whose amplitudes have opposite sign, i.e. are phase-shifted. [24]

These boundaries can be found in the sarcomeres of muscles (protein = myosin), for instance. Note that we have considered here only the forward generation.

Moreover the SHG phase-matching can also result in : some SHG is also emitted in backward (epi direction). When the phase-matching is not fulfilled, as in biological tissues, the backward signal comes from a sufficiently high phase-mismatch which allow a small backward contribution to compensate for it. [25] Unlike fluorescence, the spatial coherence of the process constrain it to emit only in those two directions, but the coherence length in backward is always way smaller than in forward, meaning there is always more forward than backward SHG signal. [26]

SHG radiation pattern in forward (F) and backward (B) from different dipoles arangment: (a) single dipoles, thus F = B ; (b) a small stack of dipoles, F > B ; (c) a large stack of dipoles, F >> B ; (d) the Gouy phase-shift cancels the SHGs, F & B weak FB diagram stacking.png
SHG radiation pattern in forward (F) and backward (B) from different dipoles arangment: (a) single dipoles, thus F = B ; (b) a small stack of dipoles, F > B ; (c) a large stack of dipoles, F >> B ; (d) the Gouy phase-shift cancels the SHGs, F & B weak

The forward (F) to backward (B) ratio is dependent on the arrangement of the different dipoles (green in figure) that are being excited. With only one dipole ((a) in the figure), F = B, but F becomes higher than B when more dipoles are stacked along the propagation direction (b and c). However, the Gouy phase-shift of the Gaussian beam will imply a phase-shift between the SHGs generated at the edges of the focal volume, and can thus result in destructive interferences (zero signal) if there are dipoles at these edges having the same orientation (case (d) in the figure).

Applications

Green lasers

Second-harmonic generation is used by the laser industry to make green 532 nm lasers from a 1064 nm source. The 1064 nm light is fed through a bulk nonlinear crystal (typically made of KDP or KTP). In high-quality diode lasers the crystal is coated on the output side with an infrared filter to prevent leakage of intense 1064 nm or 808 nm infrared light into the beam. Both of these wavelengths are invisible and do not trigger the defensive "blink-reflex" reaction in the eye and can therefore be a special hazard to human eyes. Furthermore, some laser safety eyewear intended for argon or other green lasers may filter out the green component (giving a false sense of safety), but transmit the infrared. Nevertheless, some "green laser pointer" products have become available on the market which omit the expensive infrared filter, often without warning. [27]

Ultra-short pulse measurement

Second-harmonic generation is also used for measuring ultra-short pulse widths with autocorrelators. Characterizing an ultrashort pulse (like measuring its temporal width) cannot be done directly with electronics only, as the time-scale is below 1ps (sec) : it needs to use the pulse itself, that is why an autocorrelation function is often used. SHG has the advantage of mixing two input fields to generate the harmonic one, it is thus a good candidate (but not the only one) to perform such a pulse measurement. Optical autocorrelation, in its intensity or fringe-resolved (interferometric) version use SHG, [28] unlike field autocorrelation. Also, most versions of the FROG (called SHG-FROG) use SHG to mix the delayed fields. [29]

Second-harmonic generation microscopy

In biological and medical science, the effect of second-harmonic generation is used for high-resolution optical microscopy. Because of the non-zero second-harmonic coefficient, only non-centrosymmetric structures are capable of emitting SHG light. One such structure is collagen, which is found in most load-bearing tissues. Using a short-pulse laser such as a femtosecond laser and a set of appropriate filters the excitation light can be easily separated from the emitted, frequency-doubled SHG signal. This allows for very high axial and lateral resolution comparable to that of confocal microscopy without having to use pinholes. SHG microscopy has been used for studies of the cornea [30] and lamina cribrosa sclerae, [31] both of which consist primarily of collagen. Second-harmonic generation can be produced by several non-centrosymmetric organic dyes; however, most of the organic dyes also generate collateral fluorescence along with second-harmonic generation signals. [32] Until now, only two classes of organic dyes have been shown which do not produce any collateral fluorescence and works purely on second-harmonic generation. [32] [33] Recently, using two-photon excited fluorescence and second-harmonic generation-based microscopy, a group of Oxford University researchers showed that organic porphyrin-type molecules can have different transition dipole moments for two-photon fluorescence and second-harmonic generation, [34] which are otherwise thought to occur from the same transition dipole moment. [35]

Second-harmonic generation microscopy is also used in material science, for instance to characterize nanostructured materials. [36]

Characterization of crystalline materials

Second harmonic generation is also relevant to characterize organic or inorganic crystals [37] since is one of the most discriminant and rapid technique to detect non-centrosymmetry. [38] In addition, this technique can be used on single crystal as well as on powdered samples. One should recall that SHG is only possible (from the bulk) in non-centrosymmetric (NC) crystals. The part of non-centroysmmetric crystals in nature is much lower than centrosymmetric crystals (circa 22% of the Cambridge structural database [39] ), but the frequency of NC crystals increases by a lot in pharmaceutical, biological and electronic fields because of the particular properties of these crystals (piezoelectricity, pyroelectricity, polar phases, chirality, etc.).

In 1968 [40] (7 years after the first experimental evidence of SHG on single crystal [9] ), Kurtz and Perry started to develop a SHG analyzer to rapidly detect the presence or not of inversion center in powdered crystalline samples. The detection of a SHG signal has been shown to be reliable and sensitive test for the detection of crystalline non-centrosymmetry with the confidence level higher than 99%. It is a relevant tool to resolve space group ambiguities that can arise from Friedel's law in single-crystal X-ray diffraction. [41] Furthermore, the method is referenced in the International Tables for Crystallography and is described as a "powerful method of testing crystalline materials for the absence of a symmetry center." [42]

One possible application is also to rapidly discriminate chiral phases such as conglomerate that are of particular interest for pharmaceutical industries. [43] It could also be used as a technique to probe the structural purity of material if one of the impurities is NC reaching a detection threshold as low as 1 ppm [44] using Kurtz–Perry apparatus up to one part in 10 billion by volume using a SHG microscope. [45]

Due to the high sensitivity of the technique, it can be a helpful tool in the accurate determination of phase diagram [46] and can also be used to monitor phase transitions (polymorphic transition, dehydration, ...) when at least one of the phases is NC. [47] [48] [49]

Theoretical derivation (plane wave)

At low conversion

The simplest case for analysis of second-harmonic generation is a plane wave of amplitude E(ω) traveling in a nonlinear medium in the direction of its k vector. A polarization is generated at the second-harmonic frequency: [50]

where is the effective nonlinear optical coefficient which is dependent on specific components of that are involved in this particular interaction. The wave equation at 2ω (assuming negligible loss and asserting the slowly varying envelope approximation) is

where .

At low conversion efficiency (E(2ω) ≪ E(ω)) the amplitude remains essentially constant over the interaction length, . Then, with the boundary condition we obtain

In terms of the optical intensity, , this is,

This intensity is maximized for the phase-matched condition Δk = 0. If the process is not phase matched, the driving polarization at ω goes in and out of phase with generated wave E(2ω) and conversion oscillates as sin(Δkℓ/2). The coherence length is defined as . It does not pay to use a nonlinear crystal much longer than the coherence length. (Periodic poling and quasi-phase-matching provide another approach to this problem.)

With depletion

Diagram of second-harmonic generation with perfect phase matching
D
k
=
0
{\displaystyle \Delta k=0}
. Frequency doubling with perfect pase matching.gif
Diagram of second-harmonic generation with perfect phase matching .
Diagram of second-harmonic generation with an imperfect phase matching
D
k
[?]
0
{\displaystyle \Delta k\neq 0}
. In this case energy flows forth and back from the pump to the frequency doubled signal, and having a thick crystal can lead to a smaller amount of SHG produced. Frequency doubling with imperfect phase matching.gif
Diagram of second-harmonic generation with an imperfect phase matching . In this case energy flows forth and back from the pump to the frequency doubled signal, and having a thick crystal can lead to a smaller amount of SHG produced.

When the conversion to 2nd harmonic becomes significant it becomes necessary to include depletion of the fundamental. The energy conversion states that all the involved fields verify the Manley–Rowe relations. One then has the coupled equations: [51]

where denotes the complex conjugate. For simplicity, assume phase matched generation (). Then, energy conservation requires that

where is the complex conjugate of the other term, or

Phase-matched SHG with source depletion (blue), and corresponding excitation (orange). L is the interaction length (l in the text). Phase-matched SHG with source depletion.png
Phase-matched SHG with source depletion (blue), and corresponding excitation (orange). L is the interaction length ( in the text).

Now we solve the equations with the premise

and obtain

which leads to

Using

we get

If we assume a real , the relative phases for real harmonic growth must be such that . Then

or

where . From , it also follows that

Theoretical expression with Gaussian beams

The excitation wave is assumed to be a Gaussian beam, of amplitude:

with , the direction of propagation, the Rayleigh range, the wave vector.

Each wave verifies the wave equation

where .

With phase-matching

It can be shown that:

(a Gaussian), is a solution of the equation (n = 2 for SHG).

No phase-matching

Intensity SHG, phase-matched or not. The medium width is supposed to be much higher than z, the Rayleigh range at 20 mm, excitation wavelength of 0.8 mm, and optical index of 2.2. Intensity SHG, phase-matched or not.png
Intensity SHG, phase-matched or not. The medium width is supposed to be much higher than z, the Rayleigh range at 20 μm, excitation wavelength of 0.8 μm, and optical index of 2.2.

A non-perfect phase-matching is a more realistic condition in practice, especially in biological samples. The paraxial approximation is however supposed still valid: , and in the harmonic expression, is now .

In the special case of SHG (n = 2), in a medium of length L and a focus position , the intensity writes: [52]

where is the speed of light in vacuum, the vacuum permittivity, the optical index of the medium at and the waist size of excitation.

Thus, the SHG intensity quickly decays in the bulk (), due to the Gouy phase-shift of the Gaussian beam.

In conformity with experiments, the SHG signal vanishes in the bulk (if the medium thickness is too large), and the SHG must be generated at the surface of the material: the conversion therefore does not strictly scales with the square of the number of scatterers, contrary to what the plane wave model indicates. Interestingly, the signal also vanishes in bulk for higher orders, like THG.

Materials used

Materials capable of generating a second harmonic are crystals without inversion symmetry, except crystals with point group 432. This eliminates water and glass. [50]

Notably, filamentous biological proteins with a cylindrical symmetric such as collagen, tubulin or myosin, but also certain carbohydrates (such as starch or cellulose) are also quite good converters of SHG (fundamental in the near infrared). [53]

Examples of crystals used with for SHG conversion:

For common types of diode-pumped solid state lasers with input wavelengths:

See also

Related Research Articles

<span class="mw-page-title-main">Nonlinear optics</span> Branch of physics

Nonlinear optics (NLO) is the branch of optics that describes the behaviour of light in nonlinear media, that is, media in which the polarization density P responds non-linearly to the electric field E of the light. The non-linearity is typically observed only at very high light intensities (when the electric field of the light is >108 V/m and thus comparable to the atomic electric field of ~1011 V/m) such as those provided by lasers. Above the Schwinger limit, the vacuum itself is expected to become nonlinear. In nonlinear optics, the superposition principle no longer holds.

<span class="mw-page-title-main">Electro-optic modulator</span> Type of optical device

An electro-optic modulator (EOM) is an optical device in which a signal-controlled element exhibiting an electro-optic effect is used to modulate a beam of light. The modulation may be imposed on the phase, frequency, amplitude, or polarization of the beam. Modulation bandwidths extending into the gigahertz range are possible with the use of laser-controlled modulators.

<span class="mw-page-title-main">Resonance</span> Tendency to oscillate at certain frequencies

In physics, resonance refers to a wide class of phenomena that arise as a result of matching temporal or spatial periods of oscillatory objects. For an oscillatory dynamical systems driven by a time-varying external force, resonance occurs when the frequency of the external force coincides with the natural frequency of the system. Resonance can occur in various systems, such as mechanical, electrical, or acoustic systems, and it is desirable in certain applications, such as musical instruments or radio receivers. Resonance can also be undesirable, leading to excessive vibrations or even structural failure in some cases.

In optics, an ultrashort pulse, also known as an ultrafast event, is an electromagnetic pulse whose time duration is of the order of a picosecond or less. Such pulses have a broadband optical spectrum, and can be created by mode-locked oscillators. Amplification of ultrashort pulses almost always requires the technique of chirped pulse amplification, in order to avoid damage to the gain medium of the amplifier.

<span class="mw-page-title-main">Optical parametric oscillator</span>

An optical parametric oscillator (OPO) is a parametric oscillator that oscillates at optical frequencies. It converts an input laser wave with frequency into two output waves of lower frequency by means of second-order nonlinear optical interaction. The sum of the output waves' frequencies is equal to the input wave frequency: . For historical reasons, the two output waves are called "signal" and "idler", where the output wave with higher frequency is the "signal". A special case is the degenerate OPO, when the output frequency is one-half the pump frequency, , which can result in half-harmonic generation when signal and idler have the same polarization.

Self-phase modulation (SPM) is a nonlinear optical effect of light–matter interaction. An ultrashort pulse of light, when travelling in a medium, will induce a varying refractive index of the medium due to the optical Kerr effect. This variation in refractive index will produce a phase shift in the pulse, leading to a change of the pulse's frequency spectrum.

Frequency-resolved optical gating (FROG) is a general method for measuring the spectral phase of ultrashort laser pulses, which range from subfemtosecond to about a nanosecond in length. Invented in 1991 by Rick Trebino and Daniel J. Kane, FROG was the first technique to solve this problem, which is difficult because, ordinarily, to measure an event in time, a shorter event is required with which to measure it. For example, to measure a soap bubble popping requires a strobe light with a shorter duration to freeze the action. Because ultrashort laser pulses are the shortest events ever created, before FROG, it was thought by many that their complete measurement in time was not possible. FROG, however, solved the problem by measuring an "auto-spectrogram" of the pulse, in which the pulse gates itself in a nonlinear-optical medium and the resulting gated piece of the pulse is then spectrally resolved as a function of the delay between the two pulses. Retrieval of the pulse from its FROG trace is accomplished by using a two-dimensional phase-retrieval algorithm.

Quasi-phase-matching is a technique in nonlinear optics which allows a positive net flow of energy from the pump frequency to the signal and idler frequencies by creating a periodic structure in the nonlinear medium. Momentum is conserved, as is necessary for phase-matching, through an additional momentum contribution corresponding to the wavevector of the periodic structure. Consequently, in principle any three-wave mixing process that satisfies energy conservation can be phase-matched. For example, all the optical frequencies involved can be collinear, can have the same polarization, and travel through the medium in arbitrary directions. This allows one to use the largest nonlinear coefficient of the material in the nonlinear interaction.

Sum-frequency generation (SFG) is a second order nonlinear optical process based on the mixing of two input photons at frequencies and to generate a third photon at frequency . As with any optical phenomenon in nonlinear optics, this can only occur under conditions where: the light is interacting with matter, that lacks centrosymmetry ; the light has a very high intensity . Sum-frequency generation is a "parametric process", meaning that the photons satisfy energy conservation, leaving the matter unchanged:

Multiphoton intrapulse interference phase scan (MIIPS) is a method used in ultrashort laser technology that simultaneously measures, and compensates femtosecond laser pulses using an adaptive pulse shaper. When an ultrashort laser pulse reaches a duration of less than a few hundred femtosecond, it becomes critical to characterize its duration, its temporal intensity curve, or its electric field as a function of time. Classical photodetectors measuring the intensity of light are still too slow to allow for a direct measurement, even with the fastest photodiodes or streak cameras.

<span class="mw-page-title-main">Harmonic generation</span> Nonlinear optical process

Harmonic generation is a nonlinear optical process in which photons with the same frequency interact with a nonlinear material, are "combined", and generate a new photon with times the energy of the initial photons.

In optics, the term soliton is used to refer to any optical field that does not change during propagation because of a delicate balance between nonlinear and dispersive effects in the medium. There are two main kinds of solitons:

<span class="mw-page-title-main">Self-focusing</span>

Self-focusing is a non-linear optical process induced by the change in refractive index of materials exposed to intense electromagnetic radiation. A medium whose refractive index increases with the electric field intensity acts as a focusing lens for an electromagnetic wave characterized by an initial transverse intensity gradient, as in a laser beam. The peak intensity of the self-focused region keeps increasing as the wave travels through the medium, until defocusing effects or medium damage interrupt this process. Self-focusing of light was discovered by Gurgen Askaryan.

<span class="mw-page-title-main">Second-harmonic imaging microscopy</span>

Second-harmonic imaging microscopy (SHIM) is based on a nonlinear optical effect known as second-harmonic generation (SHG). SHIM has been established as a viable microscope imaging contrast mechanism for visualization of cell and tissue structure and function. A second-harmonic microscope obtains contrasts from variations in a specimen's ability to generate second-harmonic light from the incident light while a conventional optical microscope obtains its contrast by detecting variations in optical density, path length, or refractive index of the specimen. SHG requires intense laser light passing through a material with a noncentrosymmetric molecular structure, either inherent or induced externally, for example by an electric field.

Surface second harmonic generation is a method for probing interfaces in atomic and molecular systems. In second harmonic generation (SHG), the light frequency is doubled, essentially converting two photons of the original beam of energy E into a single photon of energy 2E as it interacts with noncentrosymmetric media. Surface second harmonic generation is a special case of SHG where the second beam is generated because of a break of symmetry caused by an interface. Since centrosymmetric symmetry in centrosymmetric media is only disrupted in the first atomic or molecular layer of a system, properties of the second harmonic signal then provide information about the surface atomic or molecular layers only. Surface SHG is possible even for materials which do not exhibit SHG in the bulk. Although in many situations the dominant second harmonic signal arises from the broken symmetry at the surface, the signal in fact always has contributions from both the surface and bulk. Thus, the most sensitive experiments typically involve modification of a surface and study of the subsequent modification of the harmonic generation properties.

<span class="mw-page-title-main">Cross-polarized wave generation</span>

Cross-polarized wave (XPW) generation is a nonlinear optical process that can be classified in the group of frequency degenerate processes. It can take place only in media with anisotropy of third-order nonlinearity. As a result of such nonlinear optical interaction at the output of the nonlinear crystal, it is generated a new linearly polarized wave at the same frequency, but with polarization oriented perpendicularly to the polarization of input wave

In the fields of nonlinear optics and fluid dynamics, modulational instability or sideband instability is a phenomenon whereby deviations from a periodic waveform are reinforced by nonlinearity, leading to the generation of spectral-sidebands and the eventual breakup of the waveform into a train of pulses.

The numerical models of lasers and the most of nonlinear optical systems stem from Maxwell–Bloch equations (MBE). This full set of Partial Differential Equations includes Maxwell equations for electromagnetic field and semiclassical equations of the two-level atoms. For this reason the simplified theoretical approaches were developed for numerical simulation of laser beams formation and their propagation since the early years of laser era. The Slowly varying envelope approximation of MBE follows from the standard nonlinear wave equation with nonlinear polarization as a source:

Spectral interferometry (SI) or frequency-domain interferometry is a linear technique used to measure optical pulses, with the condition that a reference pulse that was previously characterized is available. This technique provides information about the intensity and phase of the pulses. SI was first proposed by Claude Froehly and coworkers in the 1970s.

Kleinman symmetry, named after American physicist D.A. Kleinman, gives a method of reducing the number of distinct coefficients in the rank-3 second order nonlinear optical susceptibility when the applied frequencies are much smaller than any resonant frequencies.

References

  1. He, Maosheng; Forbes, Jeffrey M. (2022-12-07). "Rossby wave second harmonic generation observed in the middle atmosphere". Nature Communications. 13 (1): 7544. Bibcode:2022NatCo..13.7544H. doi:10.1038/s41467-022-35142-3. ISSN   2041-1723. PMC   9729661 . PMID   36476614.
  2. Franken, P. A.; Hill, A. E.; Peters, C. W.; Weinreich, G. (1961-08-15). "Generation of Optical Harmonics". Physical Review Letters. 7 (4): 118–119. Bibcode:1961PhRvL...7..118F. doi: 10.1103/PhysRevLett.7.118 .
  3. Boyd, R. (2007). "The Nonlinear Optical Susceptibility". Nonlinear optics (third ed.). pp. 1–67. doi:10.1016/B978-0-12-369470-6.00001-0. ISBN   9780123694706. S2CID   15660817.
  4. Cardoso, G. C.; Pradhan, P.; Morzinski, J.; Shahriar, M. S. (2005). "In situ detection of the temporal and initial phase of the second harmonic of a microwave field via incoherent fluorescence". Physical Review A. 71 (6): 063408. arXiv: quant-ph/0410219 . Bibcode:2005PhRvA..71f3408C. doi:10.1103/PhysRevA.71.063408.
  5. Pradhan, P.; Cardoso, G. C.; Shahriar, M. S. (2009). "Suppression of error in qubit rotations due to Bloch–Siegert oscillation via the use of off-resonant Raman excitation". Journal of Physics B: Atomic, Molecular and Optical Physics. 42 (6): 065501. Bibcode:2009JPhB...42f5501P. doi:10.1088/0953-4075/42/6/065501. S2CID   15051122.
  6. Nye, J. F. (1985). Physical properties of crystals: their representation by tensors and matrices (1st published in pbk. with corrections, 1985 ed.). Oxford [Oxfordshire]: Clarendon Press. ISBN   0-19-851165-5. OCLC   11114089.
  7. Kleinman, D. A. (1962-11-15). "Theory of Second Harmonic Generation of Light". Physical Review. 128 (4): 1761–1775. Bibcode:1962PhRv..128.1761K. doi:10.1103/PhysRev.128.1761. ISSN   0031-899X.
  8. Dailey, Christopher A.; Burke, Brian J.; Simpson, Garth J. (May 2004). "The general failure of Kleinman symmetry in practical nonlinear optical applications". Chemical Physics Letters. 390 (1–3): 8–13. Bibcode:2004CPL...390....8D. doi:10.1016/j.cplett.2004.03.109.
  9. 1 2 3 Franken, P.; Hill, A.; Peters, C.; Weinreich, G. (1961). "Generation of Optical Harmonics". Physical Review Letters. 7 (4): 118–119. Bibcode:1961PhRvL...7..118F. doi: 10.1103/PhysRevLett.7.118 .
  10. Haroche, Serge (October 17, 2008). "Essay: Fifty Years of Atomic, Molecular and Optical Physics in Physical Review Letters". Physical Review Letters. 101 (16): 160001. Bibcode:2008PhRvL.101p0001H. doi:10.1103/PhysRevLett.101.160001. PMID   18999650.
  11. Bloembergen, N.; Pershan, P. S. (1962). "Light Waves at Boundary of Nonlinear Media" (PDF). Physical Review. 128 (2): 606–622. Bibcode:1962PhRv..128..606B. doi:10.1103/PhysRev.128.606. hdl:1874/7432.
  12. "Critical phase-matching". rp-photonics.com. Retrieved 2019-11-01.
  13. "Noncritical phase-matching". rp-photonics.com. Retrieved 2019-11-01.
  14. Heinz, T. F.; et al. (1982). "Spectroscopy of Molecular Monolayers by Resonant 2nd-Harmonic Generation". Physical Review Letters. 48 (7): 478–81. Bibcode:1982PhRvL..48..478H. doi:10.1103/PhysRevLett.48.478.
  15. Shen, Y. R. (1989). "Surface-Properties Probed by 2nd-Harmonic and Sum-Frequency Generation". Nature. 337 (6207): 519–25. Bibcode:1989Natur.337..519S. doi:10.1038/337519a0. S2CID   4233043.
  16. Brown, F.; Matsuoka, M. (1969). "Effect of Adsorbed Surface Layers on Second-Harmonic Light from Silver". Physical Review. 185 (3): 985–987. Bibcode:1969PhRv..185..985B. doi:10.1103/PhysRev.185.985.
  17. Eisenthal, K. B. (1992). "Equilibrium and Dynamic Processes at Interfaces by 2nd Harmonic and Sum Frequency Generation". Annual Review of Physical Chemistry. 43 (1): 627–61. doi:10.1146/annurev.physchem.43.1.627.
  18. Kemnitz, K.; et al. (1986). "The Phase of 2nd-Harmonic Light Generated at an Interface and Its Relation to Absolute Molecular-Orientation". Chemical Physics Letters. 131 (4–5): 285–90. Bibcode:1986CPL...131..285K. CiteSeerX   10.1.1.549.6666 . doi:10.1016/0009-2614(86)87152-4. S2CID   53476039.
  19. Dadap, J. I.; Shan, J.; Heinz, T. F. (2004). "Theory of Optical Second-Harmonic Generation from a Sphere of Centrosymmetric Material: Small-Particle Limit". Journal of the Optical Society of America B. 21 (7): 1328–47. Bibcode:2004JOSAB..21.1328D. doi:10.1364/JOSAB.21.001328.
  20. Eisenthal, K. B. (2006). "Second Harmonic Spectroscopy of Aqueous Nano- and Microparticle Interfaces". Chemical Reviews. 106 (4): 1462–77. doi:10.1021/cr0403685. PMID   16608187.
  21. Chan, S. W.; et al. (2006). "Second Harmonic Generation in Zinc Oxide Nanorods". Applied Physics B: Lasers and Optics. 84 (1–2): 351–55. Bibcode:2006ApPhB..84..351C. doi:10.1007/s00340-006-2292-0. S2CID   120094124.
  22. Zeng, Jia; et al. (2013). "Time-Resolved Molecular Transport across Living Cell Membranes". Biophysical Journal. 104 (1): 139–45. Bibcode:2013BpJ...104..139Z. doi:10.1016/j.bpj.2012.11.3814. PMC   3540258 . PMID   23332066.
  23. Fan, W.; et al. (2006). "Second Harmonic Generation from a Nanopatterned Isotropic Nonlinear Material". Nano Letters. 6 (5): 1027–30. Bibcode:2006NanoL...6.1027F. CiteSeerX   10.1.1.172.8506 . doi:10.1021/nl0604457.
  24. Moreaux, Laurent; Sandre, Olivier; Charpak, Serge; Blanchard-Desce, Mireille; Mertz, Jerome (2001). "Coherent Scattering in Multi-Harmonic Light Microscopy". Biophysical Journal. 80 (3): 1568–1574. Bibcode:2001BpJ....80.1568M. doi:10.1016/S0006-3495(01)76129-2. ISSN   0006-3495. PMC   1301348 . PMID   11222317.
  25. Campagnola, Paul J; Loew, Leslie M (2003). "Second-harmonic imaging microscopy for visualizing biomolecular arrays in cells, tissues and organisms". Nature Biotechnology. 21 (11): 1356–1360. doi:10.1038/nbt894. ISSN   1087-0156. PMID   14595363. S2CID   18701570.
  26. LaComb, Ronald; Nadiarnykh, Oleg; Townsend, Sallie S.; Campagnola, Paul J. (2008). "Phase matching considerations in second harmonic generation from tissues: Effects on emission directionality, conversion efficiency and observed morphology". Optics Communications. 281 (7): 1823–1832. Bibcode:2008OptCo.281.1823L. doi:10.1016/j.optcom.2007.10.040. ISSN   0030-4018. PMC   2390911 . PMID   19343083.
  27. A warning about IR in green cheap green laser pointers
  28. Trebino, Rick; Zeek, Erik (2000). "Chap4, The Autocorrelation, the Spectrum, and Phase Retrieval". Frequency-Resolved Optical Gating: The Measurement of Ultrashort Laser Pulses . Springer. pp.  61–99. doi:10.1007/978-1-4615-1181-6_4. ISBN   978-1-4615-1181-6.
  29. Trebino, Rick (2003). "Chap5, FROG". Frequency-Resolved Optical Gating: The Measurement of Ultrashort Laser Pulses . Springer. pp.  61–99. doi:10.1007/978-1-4615-1181-6_5. ISBN   978-1-4615-1181-6.
  30. Han, M; Giese, G; Bille, J (2005). "Second harmonic generation imaging of collagen fibrils in cornea and sclera". Optics Express. 13 (15): 5791–7. Bibcode:2005OExpr..13.5791H. doi: 10.1364/OPEX.13.005791 . PMID   19498583.
  31. Brown, Donald J.; Morishige, Naoyuki; Neekhra, Aneesh; Minckler, Don S.; Jester, James V. (2007). "Application of second harmonic imaging microscopy to assess structural changes in optic nerve head structure ex vivo". Journal of Biomedical Optics. 12 (2): 024029. Bibcode:2007JBO....12b4029B. doi: 10.1117/1.2717540 . PMID   17477744. S2CID   33236022.
  32. 1 2 Khadria A, Fleischhauer J, Boczarow I, Wilkinson JD, Kohl MM, Anderson HL (2018). "Porphyrin Dyes for Nonlinear Optical Imaging of Live Cells". iScience. 4: 153–163. Bibcode:2018iSci....4..153K. doi:10.1016/j.isci.2018.05.015. PMC   6147020 . PMID   30240737.
  33. Nuriya M, Fukushima S, Momotake A, Shinotsuka T, Yasui M, Arai T (2016). "Multimodal two-photon imaging using a second-harmonic generation-specific dye". Nature Communications. 7: 11557. Bibcode:2016NatCo...711557N. doi:10.1038/ncomms11557. PMC   4865818 . PMID   27156702.
  34. Khadria A, Coene Y, Gawel P, Roche C, Clays K, Anderson HL (2017). "Push–pull pyropheophorbides for nonlinear optical imaging". Organic and Biomolecular Chemistry. 15 (4): 947–956. doi:10.1039/C6OB02319C. PMID   28054076. S2CID   3540505.
  35. Reeve JE, Corbett AD, Boczarow I, Wilson T, Bayley H, Anderson HL (2012). "Probing the Orientational Distribution of Dyes in Membranes through Multiphoton Microscopy". Biophysical Journal. 103 (5): 907–917. Bibcode:2012BpJ...103..907R. doi:10.1016/j.bpj.2012.08.003. PMC   3433607 . PMID   23009840.
  36. Valev, V. K. (2012). "Characterization of nanostructured plasmonic surfaces with second harmonic generation". Langmuir. 28 (44): 15454–15471. doi:10.1021/la302485c. PMID   22889193.
  37. Simon, Florent; Clevers, Simon; Dupray, Valérie; Coquerel, Gérard (2015). "Relevance of the Second Harmonic Generation to Characterize Crystalline Samples". Chemical Engineering & Technology. 38 (6): 971–983. doi:10.1002/ceat.201400756.
  38. Abrahams, S. C. (1972-04-01). "Letter to the Editor". Journal of Applied Crystallography. 5 (2): 143. Bibcode:1972JApCr...5..143A. doi: 10.1107/S0021889872009045 . ISSN   0021-8898.
  39. "CCDC Statistics".
  40. Kurtz, S. K.; Perry, T. T. (1968). "A Powder Technique for the Evaluation of Nonlinear Optical Materials". Journal of Applied Physics. 39 (8): 3798–3813. Bibcode:1968JAP....39.3798K. doi: 10.1063/1.1656857 . ISSN   0021-8979.
  41. Dougherty, J. P.; Kurtz, S. K. (1976-04-01). "A second harmonic analyzer for the detection of non-centrosymmetry". Journal of Applied Crystallography. 9 (2): 145–158. Bibcode:1976JApCr...9..145D. doi:10.1107/S0021889876010789. ISSN   0021-8898.
  42. International tables for crystallography. International Union of Crystallography. (5th rev. ed.). Dordrecht: Kluwer. 2002. ISBN   0-7923-6591-7. OCLC   48400542.{{cite book}}: CS1 maint: others (link)
  43. Galland, Arnaud; Dupray, Valerie; Berton, Benjamin; Morin-Grognet, Sandrine; Sanselme, Morgane; Atmani, Hassan; Coquerel, Gérard (2009-06-03). "Spotting Conglomerates by Second Harmonic Generation". Crystal Growth & Design. 9 (6): 2713–2718. doi:10.1021/cg801356m. ISSN   1528-7483.
  44. Clevers, S.; Simon, F.; Dupray, V.; Coquerel, G. (2013). "Temperature resolved second harmonic generation to probe the structural purity of m-hydroxybenzoic acid". Journal of Thermal Analysis and Calorimetry. 112 (1): 271–277. doi:10.1007/s10973-012-2763-y. ISSN   1388-6150. S2CID   138727698.
  45. Wanapun, Duangporn; Kestur, Umesh S.; Kissick, David J.; Simpson, Garth J.; Taylor, Lynne S. (2010). "Selective Detection and Quantitation of Organic Molecule Crystallization by Second Harmonic Generation Microscopy". Analytical Chemistry. 82 (13): 5425–5432. doi:10.1021/ac100564f. ISSN   0003-2700. PMID   20515064.
  46. Yuan, Lina; Clevers, Simon; Couvrat, Nicolas; Cartigny, Yohann; Dupray, Valérie; Coquerel, Gérard (2016). "Precise Urea/Water Eutectic Composition by Temperature-Resolved Second Harmonic Generation". Chemical Engineering & Technology. 39 (7): 1326–1332. doi:10.1002/ceat.201600032.
  47. Yuan, Lina; Clevers, Simon; Burel, Antoine; Negrier, Philippe; Barrio, Maria del; Ben Hassine, Bacem; Mondieig, Denise; Dupray, Valérie; Tamarit, Josep Ll.; Coquerel, Gérard (2017-06-07). "New Intermediate Polymorph of 1-Fluoro-adamantane and Its Second-Order-like Transition toward the Low Temperature Phase". Crystal Growth & Design. 17 (6): 3395–3401. doi:10.1021/acs.cgd.7b00353. hdl: 2117/106369 . ISSN   1528-7483.
  48. Clevers, S.; Rougeot, C.; Simon, F.; Sanselme, M.; Dupray, V.; Coquerel, G. (2014). "Detection of order–disorder transition in organic solids by using temperature resolved second harmonic generation (TR-SHG)". Journal of Molecular Structure. 1078: 61–67. Bibcode:2014JMoSt1078...61C. doi:10.1016/j.molstruc.2014.04.007.
  49. Clevers, Simon; Simon, Florent; Sanselme, Morgane; Dupray, Valerie; Coquerel, Gerard (2013-08-07). "Monotropic Transition Mechanism of m -Hydroxybenzoic Acid Investigated by Temperature-Resolved Second Harmonic Generation". Crystal Growth & Design. 13 (8): 3697–3704. doi:10.1021/cg400712s. ISSN   1528-7483.
  50. 1 2 Boyd, R.W. (2008). Nonlinear Optics, 3rd edition. Academic Press. ISBN   9780121216801.
  51. Zernike, Frits; Midwinter, John E. (1973). Applied Nonlinear Optics. John Wiley & Sons Inc. ISBN   0-486-45360-X.
  52. Stoller, Patrick; Celliers, Peter M.; Reiser, Karen M.; Rubenchik, Alexander M. (2003). "Quantitative second-harmonic generation microscopy in collagen". Applied Optics. 42 (25): 5209–19. Bibcode:2003ApOpt..42.5209S. doi:10.1364/AO.42.005209. ISSN   0003-6935. PMID   12962402.
  53. Pavone, Francesco S.; Campagnola, Paul J. (2016). Second Harmonic Generation Imaging (2nd ed.). CRC Taylor & Francis. ISBN   978-1-4398-4914-9.
  54. "BiBO Crystals". newlightphotonics.com. Retrieved 2019-11-01.
  55. "LiIO3 crystals – Lithium Iodate Crystal". shalomeo.com. Retrieved 2019-11-01.
  56. "KNbO3". laser-crylink.com. Retrieved 2019-11-01.
  57. "BBO Crystals". newlightphotonics.com. Retrieved 2019-11-01.
  58. "KTP Crystals". unitedcrystals.com. Retrieved 2019-11-01.
  59. Meyn, J.-P.; Laue, C.; Knappe, R.; Wallenstein, R.; Fejer, M. M. (2001). "Fabrication of periodically poled lithium tantalate for UV generation with diode lasers". Applied Physics B. 73 (2): 111–114. Bibcode:2001ApPhB..73..111M. doi:10.1007/s003400100623. S2CID   119763435.

Articles