News item, May 7, 1875 | |
History | |
---|---|
Name: | Senator |
Owner: | People's Transportation Co.; Oregon Steamship Co. |
Route: | Willamette River |
In service: | 1863 |
Out of service: | 1875 |
Identification: | U.S. 23148 |
Fate: | Destroyed by boiler explosion |
General characteristics | |
Type: | inland steamship |
Length: | 123 ft (37.5 m) exclusive of fantail. |
Beam: | 21 ft (6.4 m) exclusive of guards |
Depth: | 5 ft (1.5 m) 3.5 ft (1.1 m) or depth of hold |
Installed power: | twin high-pressure steam engines, horizontally mounted, single cylinder, bore 12.25 in (0.31 m), stroke 48 in (1.22 m). |
Propulsion: | stern-wheel |
Senator was a stern-wheel-driven steamboat which operated on the Willamette River in the state of Oregon from 1863 to 1875. Senator is chiefly remembered for its having been destroyed in a fatal boiler explosion in 1875 while making a landing at the Portland, Oregon waterfront in 1875.
Senator was built in 1863 at Milwaukie, Oregon by shipbuilder John T. Thomas (1808-1890) for steamboat captain Joseph Kellogg. [1] The steamer made its trial trip on January 22, 1864. [1] The dimensions of the hull were length 123 feet; beam (width) 21 feet; depth of hold 5.0 feet; draft light (unloaded) 22 inches. [1] Gross tonnage in 1874 for Senator was 297.99. [2]
The official merchant vessel registry number for Senator was 23148. [2]
The machinery for Senator came from the steamer Surprise, which had been built at Canemah, Oregon in 1857. [3] [4] The boat was powered by two single cylinder steam engines, each with a bore diameter of 12.25 inches and a stroke of 48 inches. [1] The stern-wheel was 17 feet in diameter with planks, called “paddles” 14 inches across. [1]
Soon after Senator was completed, Joseph Kellogg, the owner, sold it to People's Transportation Company in exchange for stock in the company. [1]
Joseph Kellogg continued in command of Senator until 1867, when George A. Pease and E.W. Baughman became captains. [1] Capt. Charles H. Kellogg (1846-1889) took command until the steamer was sold to Ben Hollday in 1871. [1]
In October 1866, Senator was part of a transportation route to Washington County, Oregon which sought to avoid the navigation barrier then formed by Willamette Falls. [5]
Senator would run to Oswego, on the Willamette River, where passengers would disembark, and cross over to Sucker Lake, as Oswego Lake was then known. [5] The traveler would then stay overnight at Shade's Hotel in Oswego, and, the next morning, board a small sternwheeler, the Minnehaha. [5] [6]
The lake boat then paddled across the water to the lake’s western end, where it was reported, they would be taken to Colfax, on the Tualatin River “by cars”. [5] Once at Colfax, the steamer Yamhill, with Captain Kellogg in charge, would “be in readiness.” [5] The Yamhill would then steam up the Tualatin River, with, it was projected, excursionists, as far as Taylor’s Bridge. [5]
As of October 27, 1866, Senator, running for the People's Transportation Company, departed Portland daily (except Sunday) at 6:00 a.m. for Oregon City, where connections were made with Enterprise, Echo, and Active, running every Monday and Thursday for Salem, Albany and Corvallis. [7] Connections were also made at Oregon City with the Union, which ran on Mondays, Wednesdays and Fridays for Dayton and intermediate points. [7] Returning to Portland, Senator departed Oregon City daily at 1:00 p.m. [7] Captain E.W. Baughman was in charge of Senator at this time. [8]
In November 1867, Senator was under the command of Captain Thomas Berry. [9]
In July 1870, Senator was hauled out of the river at the lower end of Oregon City to undergo a major overhaul, including an increase in engine power, and apparently to have a new hull constructed under the vessel. [10] [11]
On October 21, 1870, it was reported that Senator should be receiving its machinery, and was expected to be returned to service on the route between Oregon City and Portland in the next week or two. [12]
In June 1871, Charles W. Pope was purser of the Senator. [13]
As of November 1871, Senator was being operated by the Willamette Transportation Company, departing Portland at 2:00 p.m. daily for Oregon City, and departing Oregon City the following morning at 7:30 a.m. on the return trip to Portland. [14]
On Wednesday, October 16, 1872, Senator transported several hundred barrels of cement to Oregon City to be used in the construction of the Willamette Falls Locks. [15]
On the morning of November 30, 1871, while on the way downriver from Oregon City to Portland, with a heavy load of cargo (203 tons), Senator became unmanageable in the swift currents of the Clackamas Rapids. [16] As a result, the steamer sank in about seven feet of water. [16] The cargo was taken off by another steamer E.N. Cooke. [16]
Damage to the steamer was initially thought to be considerable but still “easily repaired.” [16] Damage to the cargo could not be ascertained as of the first report of the incident. [16] Reportedly no blame for the accident could rest upon the officers of the boat. [16]
According to another report, Senator was thrown by an eddy against the rocks at Rynearson’s Point, but sank not in seven feet of water but only two or three feet, but enough to cover the steamer’s lower deck. [17] The steamer was proceeding through the eastern chute of the rapids, considered the safer route at a good stage of water, some of which was considerably. [17]
The cargo was reported to be 140 tons, mostly of flour. [17] While the project of raising and repairing the Senator was underway, the E.N. Cooke would take its place on the route. [17]
At 2:45 p.m. on May 6, 1875, the boiler on Senator exploded. [18] The steamer had just left its mooring at the dock of the Oregon Steamship Company and steamed past the city front, to the foot of Alder Street, where its speed slackened in preparation for coming alongside the steamer Vancouver, moored at the Willamette River Transportation Company wharf, where Vancouver was to transfer cargo to Senator. [18] The stern-wheel of the Senator had just ceased to revolve when the explosion occurred. [18]
The entire cabin from the pilot house to the hog post was destroyed, with the pilot house lifted 75 feet in the air and falling in the river a considerable distance away. [18] Other wreckage was scattered across the river, and several people were struggling in the water, trying to cling on to floating fragments. [18] The detonation was reported to have shaken the foundation of every building in Portland. [18] Within two minutes of the explosion three or four thousand people were hurrying towards the scene. [18]
The Senator did not immediately sink as a result of the explosion, probably because of several water-tight compartments, but instead drifted downstream and beached opposite the Oregon Steamship Company dock, after which the stern sank until the stern-wheel was under water, but the bow remained above the surface. [1] [18]
The steamer Vancouver, with an experienced steamboat man in charge, Capt. William H. Troup (1828-1882) was immediately unmoored and went to the aid of the Senator. [18] There were about 20 passengers on board Senator, most of whom had fortunately been at the rear part of the cabin, more distant from the boiler, and were relatively unhurt. [18] People alongside the river launched small boats to rescue the people in the water. [18] After all the people had been rescued, the men in the boats started picking up the floating articles of freight. [18]
It was not easily to determine how many people were killed or missing as a result of the explosion. [18] Known casualties were Captain Daniel McGill, of Oregon City, killed in the pilot house, purser Joseph D. Losey, also of Oregon City, fireman George Warner, and deckhands James Smith, John Cosgrove and John Crowley. [18] The bodies of these men were not immediately recovered. [18] A number of other people were injured, and there were some fortunate escapes. [18]
The boiler, although built in 1857, had been inspected on October 18, 1874 and found to be in good condition and was “regarded as very strong and perfectly safe.” [18] It was permitted to carry 100 pounds of steam. [18] The cause of the explosion was thought to be a pump failure resulting in the injection of cold water onto red hot heating surfaces in the boiler, creating so much steam that the boiler could not contain it, producing the explosion. [18] The boiler itself was blown to pieces. [18]
On May 11, 1875, the engineer, John V. Smith, who had been on board at the time of the explosion, was arrested and charged with manslaughter, the allegations being that through want of experience, incompetency, or criminal negligence the explosion occurred. [19] Smith was acquitted of the charge, but the explosion always weighed heavily on his mind, and he was seldom in charge of steamers afterwards. [1]
Gazelle was an early sidewheeler on the Willamette River in what is now the U.S. state of Oregon. She did not operate long, suffering a catastrophic boiler explosion on April 8, 1854, less than a month after her trial voyage. This was the worst such explosion ever to occur in the Pacific Northwest states. The wrecked Gazelle was rebuilt and operated for a few years, first briefly as the unpowered barge Sarah Hoyt and then, with boilers installed, as the steamer Señorita. A victim of the explosion was D.P. Fuller, age 28, who is buried in Lone Fir Cemetery in Portland, Oregon.
Elk was a stern-wheel driven steamboat built on the Willamette River in 1857 at Canemah, Oregon. This steamboat is chiefly remembered for its destruction by a boiler explosion in which by good fortune no one was seriously hurt. A folklore tale later arose about this disaster.
Wallamet was a sidewheel-driven steamboat that operated on the Willamette and Columbia rivers in Oregon and later on the Sacramento and San Joaquin rivers in California. Built in a Mississippi river style that was not suited to the conditions of these rivers, and suffering from construction defects, Wallamet was not a financially successful vessel. The name of this vessel is often seen spelled as Willamette.
Unio was a small sternwheel-driven steamboat which operated on the Willamette and Yamhill rivers from 1861 to 1869. This vessel is primarily remembered for its having been named Unio when built in 1861, in the first year of the American Civil War, and then having the name completed, to Union, by a new, staunchly pro-Union owner, James D. Miller. Union appears to have sunk in 1869, been salvaged, and then dismantled, with the machinery going to a new steamer then being built for service on the Umpqua River.
The People's Transportation Company operated steamboats on the Willamette River and its tributaries, the Yamhill and Tualatin rivers, in the State of Oregon from 1862 to 1871. For a brief time this company operated steamers on the Columbia River, and for about two months in 1864, the company operated a small steamer on the Clackamas River.
Shoo Fly was a sternwheel-driven steamboat that operated on the Willamette and Columbia rivers in the 1870s. Originally built as primarily as a freight boat, the vessel was used in other roles, including towing and clearing of snags. Shoo Fly inspired the name of another sternwheeler on the Willamette River, Don't Bother Me.
The Upper Willamette Transportation Line was a line of four inland steamboats that operated from the fall of 1859 to the summer of 1860 on the upper Willamette River in the state of Oregon, United States.
Enterprise was a sternwheel steamboat that operated on the Willamette River from 1863 to 1875. This vessel should not be confused with several other steamers named Enterprise which operated in the Pacific Northwest at about the some time.
Alert was a sternwheeler steamboat which operated on the Willamette River, in Oregon, United States, from 1865 to 1875. Originally built for and owned by the Willamette Steam Navigation Co., it was soon acquired by the People's Transportation Company, a steamboat line which held a near-monopoly on Willamette River transportation. This vessel was rebuilt in 1871, and ran until 1875, when it was dismantled.
Oregon was a side-wheel driven steamboat that operated on the Willamette River in the state of Oregon from 1852 to 1854. The steamer was not economically successful and became a total loss by sinking after a short career.
Alice was a stern-wheel driven steamboat that operated on the Willamette and Columbia rivers in the 1870s and 1880s. Alice was the largest vessel built above Willamette Falls and was considered in its day to be the "Queen of the River". This steamer was rebuilt after near-destruction in a fire at Oregon City, Oregon in May 1873. In 1876, it was withdrawn from the upper Willamette River and transferred to the Columbia River, where it was worked as a towboat moving ocean-going ships to and from Portland and Astoria, Oregon, near the mouth of the Columbia River.
Wenat was a stern-wheel steamboat that, under the name Swan, was built and operated, briefly, on the Tualatin River, in the state of Oregon. In 1858, Swan was sold, moved to the lower Willamette River, renamed Cowlitz, and placed on a route between Portland, Oregon the Cowlitz River.
Minnehaha was a sternwheel-driven steamboat which was built in 1866 on Oswego Lake, then known as Sucker Lake, in Oregon, United States. Minnehaha was later transferred to the Willamette and Columbia rivers where it operated for the first part of the 1870s.
Dayton was a steamboat which operated on the Willamette and Columbia rivers from 1868 to 1881. Dayton operated on the Willamette from 1868 to 1876, mostly upriver from Willamette Falls, including a route on the Yamhill River to Dayton, Oregon, after which the steamer was named. From 1876 to 1881, Dayton was employed on a run from Portland to Monticello, W.T., which was located on the site of what is now Longview, Washington.
Albany was a stern-wheel driven steamboat that operated on the Willamette River from 1868 to 1875. This vessel should not be confused with the later sternwheeler Albany, which ran, also on the Willamette River, from 1896 to 1906, when it was rebuilt and renamed Georgie Burton.
Onward was a stern-wheel driven steamboat that operated on the Tualatin River from 1867 to 1873, on Sucker Lake, now known as Oswego Lake, from 1873 to 1874, on the Cowlitz and Lewis rivers. This vessel should not be confused with the similar sternwheeler Onward built in 1858 at Canemah, Oregon and dismantled in 1865.
Active was a stern-wheel driven steamboat that operated on the upper Willamette River from 1865 to 1872. During its short operational life, Active was owned by several different steamboat companies. It was dismantled in 1872 at Canemah, Oregon.
No Wonder was a stern-wheel driven steamboat that operated on the Willamette, Columbia and Cowlitz rivers from 1889 to 1930. No Wonder was originally built in 1877 as Wonder, which was dismantled in 1888, with components being shifted over to a new hull, which when launched in late 1889 was called No Wonder.
Fanny Patton was a stern-wheel driven steamboat that operated on the Willamette River, in Oregon, starting in August 1865. This steamer operated from 1865 to 1880 for various owners, and was a considered a profitable vessel. The steamer was named for the daughter of businessman Edwin N Cook, Frances Mary "Fannie" Cooke (1837–1886), who married Thomas McFadden Patton in 1854. Edwin N. Cook was one of the principals of the People's Transportation Company.
Orient was a light-draft sternwheel-driven steamboat built in 1875 for the Willamette River Transportation Company, a concern owned by pioneer businessman Ben Holladay. Shortly after its completion, it was acquired by the Oregon Steam Navigation Company. Orient was a near-twin vessel of a steamer built at the same time, the Occident.