Accident | |
---|---|
Date | March 11, 2018 |
Summary | Crashed into river following loss of engine power |
Site | East River, New York City, US 40°46′25″N73°56′22″W / 40.773611°N 73.939444°W |
Aircraft | |
Aircraft type | Eurocopter AS350 Écureuil |
Operator | Liberty Helicopters |
Registration | N350LH |
Flight origin | Helo Kearny Heliport, New Jersey |
Destination | Helo Kearny Heliport, New Jersey |
Occupants | 6 |
Passengers | 5 |
Crew | 1 |
Fatalities | 5 |
Injuries | 1 |
Survivors | 1 |
On March 11, 2018, a sightseeing helicopter crashed into the East River off the Upper East Side of Manhattan, New York City, killing five people. Two passengers died at the scene, and three others were pronounced dead at the hospital. The pilot escaped the helicopter following the crash. The aircraft was operated by Liberty Helicopters for FlyNyon.
The aircraft involved in the incident was a Eurocopter AS350 Écureuil, that had not been involved in any prior accidents. The tour company had had two other crashes in the preceding 11 years. [1] The helicopter flew with open doors, and passengers were required to wear both the helicopter's primary restraints (seatbelts) along with a supplemental harness (provided by NYONair), designed to keep them inside the helicopter; the supplemental harnesses underwent scrutiny as a potential cause of fatality due to the difficulty of releasing the harness. [2]
The helicopter was equipped with primary restraints for the pilot and each passenger provided by the manufacturer compliant with 14 CFR 27.785 . Each passenger was also equipped with a supplemental harness system which allowed them to move within the cabin and sit in the door sill while airborne. [3] The center passengers in the four-abreast rear bench seat were allowed to remove their primary restraints, leave their seat, and sit on the sills; they were prevented from falling out of the helicopter by the supplemental harnesses. The passengers on the outboard ends of the rear seat and front passenger seat were allowed to rotate outboard, but their primary restraints were not intended to be released. [4] : 2–3 The supplemental harness was an off-the-shelf nylon fall arrest device which anchored each passenger to the helicopter; ground crew were responsible for attaching and detaching a locking carabiner to the back of each passenger's supplemental harness at the start and end of each flight. Each carabiner was at the end of a tether attached in the helicopter's cabin. The supplemental harnesses were provided by FlyNYON, the vendor which had sold the passenger tickets. [3]
The flight was being conducted by the operator Liberty Helicopters under 14 CFR 91 rules as an air tour for aerial photography for FlyNYON under 14 CFR 136 rules. [5] [6] According to a 2014 study, the crash rate of Part 91 air tours is 3.5 per 100,000 hours flown, "similar to the reported crash rates in categories considered to be 'high hazard' commercial aviation" such as medevac and off-shore drilling transport. [7] Liberty Helicopters spent $120,000 lobbying the mayor's office and the Economic Development Corporation in 2015, according to an article about the curtailment of tourist flights from the Downtown Manhattan Heliport in 2016. [8] Liberty and FlyNYON stated the flights met exemption criteria under 14 CFR 119.1 (e)(4)(iii) for aerial photography. [4] : 37–38
The flight originated from Helo Kearny Heliport (FAA LID: 65NJ) at approximately 1900 EDT on March 11, 2018. The pilot had been flying passengers for FlyNYON on flights lasting 15 to 30 minutes since 11:00 that day, although he could not recall how many flights he had completed. [6] When the van carrying the passengers arrived, the pilot checked each passenger's harness and put their life vests on. After seating the passengers in the helicopter, he locked their harness tethers to the helicopter and provided safety instructions, including where the cutting tool was on their harness and how to use it. [6]
The pilot, following the passengers' requests for sights, flew toward the Statue of Liberty at an altitude ranging from 300–500 ft (91–152 m) above ground level (agl), then proceeded to the Brooklyn Bridge and Central Park. [6] After contacting the tower at LaGuardia Airport to request entry into its controlled airspace, the pilot started to climb to approximately 2,000 ft (610 m) agl. [9] During the climb, he noticed the front passenger had removed his primary restraint, and reminded the passenger to keep the restraint fastened, as the passengers in the left front, left rear, and right rear seats were supposed to stay restrained while the inboard passengers in the center rear seats were allowed to unclip their primary restraints and sit on the floor with their feet on the skids. [6]
Onboard video reviewed after the crash showed the front passenger turned in his seat so he was facing outboard with his legs outside the helicopter. While taking several photographs between 19:00 and 19:05, he leaned backward and his supplemental harness tether hung down loosely near the helicopter's floor-mounted controls. At 19:05:51, when he sat up again, video showed the tail of the tether became taut, then suddenly released; this was followed two seconds later by decreased engine noises. [4] : 4 Radar showed the helicopter began to descend at 19:06:11. [4] : 5
According to several witnesses, the helicopter suddenly descended near the northern end of Roosevelt Island and then plummeted into the river. The helicopter was described to be autorotating at low altitudes immediately prior to its crash. [10] The pilot stated, in a post-crash interview with the National Transportation Safety Board (NTSB), that a low rotor rpm alarm began to sound and warning lights came on, indicating low engine and fuel pressure. At that point, he believed the engine had failed and considered landing at Central Park, but thought there were too many people present to attempt a landing, and directed the helicopter towards the East River instead, starting the turn at 19:06:30. [6] [4] : 5 The pilot radioed a mayday call to LaGuardia at 19:06:58. [11] [4] : 5
During the descent, the pilot attempted to restart the engine at least twice, and then he confirmed the fuel flow control lever was still positioned for normal operation. After he was sure the helicopter could reach the river, the pilot activated the skid-mounted floats at 19:07:02, 800 ft (240 m) agl. [6] [4] : 5 When he reached to engage the emergency fuel shutoff lever in preparation for a hard landing, he realized it had already been activated, and that part of a passenger's fall protection tether was underneath the fuel shutoff lever. When he disengaged the fuel shutoff lever, he was able to restart the engine, but at that point, the helicopter had already descended past 300 ft (91 m) agl and the engine "wasn't spooling up fast enough" to avoid a crash landing. He put the helicopter in a nose-up flare before it hit the water. [6]
With the doors off, the cabin began to fill with water, first on the pilot's side (right side) of the cabin. The pilot stated he started to unlock the carabiner securing the front passenger's tether to the helicopter, but had gotten no more than two or three rotations before the helicopter began to sink, rolling past a 45° list. [6] Subsequent review of a video showing the descent (recorded by a witness using a cellphone) led aviation experts to believe the passengers would have survived had the helicopter not turned over and sunk. [12] The aircraft sank 11 seconds after touching down on the water, [4] : x, 28 at approximately 19:07:26, when the onboard video camera's lens became submerged. [4] : 26
The pilot, who was not attached to the aircraft by a supplemental harness, unbuckled his manufacturer-provided primary restraint after the helicopter was submerged and escaped. [4] : 6 All five passengers drowned after the helicopter rolled over into the water as they were trapped by their supplemental harnesses. To leave the aircraft, a passenger would have had to either reach behind them and unscrew the locking carabiner (or assist another passenger with their carabiner), or use a cutting tool (provided by FlyNYON and attached to each harness) to sever the tether. [3] A passing tugboat heard the mayday call from the pilot and tied up to the helicopter to keep it from sinking further. [12] Rescue divers responded seven minutes after the first 911 call. [12] The passengers were cut out of the wreck by emergency responders, [13] some after having been dragged for 50 blocks south in the upside-down helicopter: a 3-knot (5.6 km/h; 3.5 mph) current pulled the helicopter from 86th to 34th during the rescue. [12] The pilot was taken to the hospital for observation. [13]
The NTSB opened an investigation immediately following the incident. [2]
Almost immediately, passengers on previous flights pointed out the "complicated system of straps, carabiners and an emergency blade for cutting [the proprietary eight-point Safety Harness System] off in case of trouble" and inadequate training as probable causes for the passengers' deaths in a March 12 New York Times article about the crash. [14] Several internal documents showed that pilots for Liberty and FlyNYON had requested better-fitting supplemental passenger harnesses as well as better tools that would make it easier for passengers to free themselves for up to two months preceding the fatal flight. [15] The supplemental harnesses used in most flights were yellow nylon harnesses designed as fall protection for construction workers, and the pilots stated they preferred a more expensive blue harness which was more adjustable, had been certified by the FAA for helicopter operations (under technical standard order C167), [16] and had more attachment points, some of which were more accessible to passengers. [15] Patrick Day, CEO of FlyNYON, stated to the New York Times that on October 31, 2017, "inspectors observed the harness and tethering process [at FlyNYON's facility] and continued to permit their use on Liberty and FlyNYON operated flights without issue". A spokesman for the FAA stated that supplemental harnesses are not subject to inspection. [17] FlyNYON staff were instructed to use zip ties to modify the harnesses to fit smaller passengers, and applied masking tape, which FlyNYON called "NYON blue safety tape", to prevent inadvertent release of harnesses and restraints. [17]
Passengers were provided with a hook-shaped seat belt cutter to sever the restraint tether in case of an emergency, but internal testing in November 2017 demonstrated how difficult it was to use that tool on the restraint tethers used in flight, [17] which were made using the ultra-high-molecular-weight polyethylene branded Dyneema. [15] In February, a pilot for Liberty identified a different knife and tether that could be cut "very easily" as well as a supplier that had more than fifty of each in stock, but social media postings by FlyNYON passengers showed the older tethers and cutters were still in use up to the fatal flight. [15] When discussing the restraint system used on the accident flight, NTSB Chairman Robert Sumwalt said: "The contraption that FlyNYON rigged up turned a perfectly good helicopter into a death trap." [18]
The CEO of FlyNYON, Patrick Day, not only dismissed the pilots' repeated warnings about the safety issues with the harnesses but also threatened them with termination for raising these concerns. Pilots warned that the harnesses used for "doors-off" flights were unsuitable, especially for smaller passengers, and could be difficult to release in an emergency. Despite these warnings, Day insisted that the harnesses were safe and rebuffed the pilots' concerns. The pilots expressed that their recommendations were not only ignored but were met with threats of firing, which violates fundamental aviation safety principles and training that emphasize the importance of addressing and reporting safety concerns.
Despite the crash and the warnings from pilots about the safety risks, FlyNYON, under CEO Patrick Day, continued to operate "doors-off" flights with the same harness systems. This decision was controversial and heavily criticized, especially given that the improper use of these harnesses was a major factor in the fatal crash. The FAA eventually stepped in, issuing restrictions on "doors-off" flights to ensure that passenger safety restraints could be quickly released in an emergency.
Although the Airbus AS350 B2 helicopter is not certified for ditching in water, it can be equipped with an emergency flotation system; in this case, the helicopter was equipped with a system manufactured by Dart Aerospace, type certificate SR00470LA. [4] : 10 To prevent inadvertent activation, a shear pin is designed to break under 12 pounds-force (53 N) of force; the activator is installed on the cyclic control lever. [4] : 11 The flotation system was installed by EuroTec Canada in 2013. [4] : 13
Subsequent evaluation of the wreck showed the right-side floats for the emergency flotation system were not as inflated as the left-side floats. [6] The float system must operate flawlessly according to specification and certification. The post-crash examination of N350LH showed the left skid emergency float's pressurized gas cylinder gauge indicated about 0 psi (0 kPa) while the right skid's pressurized gas cylinder gauge indicated about 4,000 psi (28,000 kPa), implying the right side had failed to fully inflate. According to the NTSB report: "The trigger mechanism was smooth with no evidence of binding. Continuity of the float system control was established between the trigger, dual cable block, and the activation cable clevis connection. When the trigger was released, the dual cable block returned to its normal position (via spring within the junction box) but the upper and lower turnbuckles remained in their actuated positions." [6]
FlyNYON is a spinoff of NY On Air (NYONair), which was founded by Patrick Day, Jr. in 2012 to coordinate aerial photography flights for professional and corporate photographers. FlyNYON sold single-seat tickets for aerial photography flights, reducing the per-passenger cost to facilitate access to doors-off photography flights for tourists. [15] FlyNYON marketed its services via social media by encouraging passengers to post pictures with the hashtag #ShoeSelfie, where the photographer's shoes could be seen in an aerial photograph. [15] [17] Day is the son of the director of operations for Liberty Helicopters. Patrick Day Sr. simultaneously held the director of operations position for FlyNYON, and Patrick Jr. was listed as the VP of charter and aircraft management for Liberty. [15]
A safety video was shown to the passengers, which included a segment on how to release the supplemental harness in case of an emergency. The video demonstrated one passenger helping another passenger to disengage the locking carabiner and also stated that a cutting tool was secured to a chest strap and could be used to cut the tether if necessary; the video showed the passenger cutting the tether with a single stroke. [4] : 44 Pilots were concerned about the adequacy of the cutting tools, and in one test, took more than 30 seconds to cut through a tether with the tools available to passengers. [4] : 53
NYONair performed an independent investigation and made the following recommendations: [19]
The family of one victim sued FlyNYON and Liberty Helicopters on March 14, alleging that it was impossible for passengers to free themselves from their harnesses during an emergency. [20] The lawsuit was later amended to add Airbus as a defendant. [21] According to NTSB safety recommendations A-10-129 and -130, issued on October 20, 2010, the design of the emergency fuel shutoff lever in the Eurocopter AS350 cockpit "allows for easy access to and inadvertent movement of (the lever), which could cause a serious or catastrophic accident if the movement occurs at a critical point during flight or on the ground." [22] [23] Airbus (then Eurocopter) had previously reviewed the design of the fuel cutoff lever prior to the safety recommendation and developed a new design, but the FAA did not require a retrofit of the new design. [22]
On March 19, NTSB issued Aviation Safety Recommendation ASR-18-02 to the Federal Aviation Administration (FAA). ASR-18-02 recommends the prohibition of all open-door passenger flights that use additional passenger harness systems, unless the harness system is designed to allow passengers to "rapidly release the harness with minimal difficulty and without having to cut or forcefully remove the harness." [3] The FAA released a statement on March 20 saying they intended to impose a ban on open-door passenger flights that use harnesses which could not be released quickly. [24] Emergency Order of Prohibition 8900.456 (FAA-2018-0243; 83 FR 12856) was issued by the FAA on March 23, effective for one year, prohibiting "doors-off" flights with supplemental passenger restraint systems unless those systems have FAA approval through Form 337. [25] [26] 8900.456 was superseded by 8900.457 in April 2018; [27] 8900.457 in turn was superseded by 8900.506, which renewed the ban on doors-off flights for another year starting in April 2019. [28]
The NTSB adopted Aircraft Accident Report (AAR) 19-04 on December 10, 2019. [29] AAR 19-04 concluded the pilot had successfully ditched the helicopter into the water in a survivable manner using an autorotative descent; however, the supplemental restraints provided by NYONair prevented the passengers from exiting the helicopter after it turned over and sank, causing them to drown. In addition, the supplemental restraint was the immediate cause of the accident; one restraint caught on and caused an inadvertent activation of the fuel shutoff lever, resulting in a loss of power. [4] : ix–x
American Airlines Flight 587 was a regularly scheduled international passenger flight from John F. Kennedy International Airport, New York City to Las Américas International Airport, Santo Domingo. On November 12, 2001, the Airbus A300B4-605R flying the route crashed into the neighborhood of Belle Harbor on the Rockaway Peninsula of Queens, New York City, shortly after takeoff, killing all 260 people aboard, as well as 5 people on the ground. It is the second-deadliest aviation accident in U.S. history, behind the crash of American Airlines Flight 191 in 1979, and the second-deadliest aviation incident involving an Airbus A300, after Iran Air Flight 655.
United Airlines Flight 232 was a regularly scheduled United Airlines flight from Stapleton International Airport in Denver to O'Hare International Airport in Chicago, continuing to Philadelphia International Airport. On July 19, 1989, the DC-10 serving the flight crash-landed at Sioux Gateway Airport in Sioux City, Iowa, after suffering a catastrophic failure of its tail-mounted engine due to an unnoticed manufacturing defect in the engine's fan disk, which resulted in the loss of all flight controls. Of the 296 passengers and crew on board, 112 died during the accident, while 184 people survived. Thirteen of the passengers were uninjured. It was the deadliest single-aircraft accident in the history of United Airlines.
The Airbus Helicopters H125 is a single-engine light utility helicopter originally designed and manufactured in France by Aérospatiale and Eurocopter. In North America, the H125 is marketed as the AStar. The AS355 Ecureuil 2 is a twin-engine variant, marketed in North America as the TwinStar.
JetBlue Flight 292 was a scheduled flight from Bob Hope Airport in Burbank, California, to John F. Kennedy International Airport in New York City. On September 21, 2005, Captain Scott Burke executed an emergency landing in the Airbus A320-232 at Los Angeles International Airport after the nose gear jammed in an abnormal position. No one was injured.
Addison Airport is a public airport in Addison, in Dallas County, Texas, United States, 9 mi north of downtown Dallas. It opened in 1954 and was purchased by the town of Addison in 1976.
The EurocopterAS355 Écureuil 2 is a twin-engine light utility helicopter developed and originally manufactured by Aérospatiale in France.
ALM Antillean Airlines Flight 980 was a flight scheduled to fly from John F. Kennedy International Airport in New York City to Princess Juliana International Airport in St. Maarten, Netherlands Antilles, on May 2, 1970. After several unsuccessful landing attempts, the aircraft's fuel was exhausted, and it made a forced water landing in the Caribbean Sea 48 km off St. Croix, with 23 fatalities and 40 survivors. The accident is one of a small number of intentional water ditchings of jet airliners.
The Champion 402 Lancer is a twin-engine trainer produced by Champion Aircraft, a high-wing monoplane based on the tricycle gear Champion 7FC Tri-Traveler, but with wing-mounted Continental O-200-A engines. The Lancer first flew in 1961 and production began in 1963. The Lancer seats two in a tandem configuration with dual flight controls; the pilot in command or student pilot normally occupies the front seat.
The safety of emergency medical services flights has become a topic of public interest in the United States, with the expansion of emergency medical services aviation operations, such as air ambulance and MEDEVAC, and the increasing frequency of related accidents.
Aero Valley Airport is a privately owned, public use airport 3 nautical miles (5.6 km) northwest of Roanoke, in Denton County, Texas, United States.
On August 8, 2009, at 11:53 a.m. (15:53 UTC), nine people died when a tour helicopter and a small private airplane collided over the Hudson River near Frank Sinatra Park in Hoboken, New Jersey, United States. The aircraft were in an area known as the "Hudson River VFR Corridor", which extends from the surface of the river to altitudes of 800 to 1,500 ft at various locations along the Hudson River in the immediate area of New York City. Within this corridor, aircraft operate under visual flight rules (VFR), under which the responsibility to see and avoid other air traffic rests with the individual pilots rather than with the air traffic controller (ATC).
The Grand Canyon mid-air collision occurred when Grand Canyon Airlines Flight 6, a de Havilland Canada DHC-6 Twin Otter, collided with a Bell 206 helicopter, Helitech Flight 2, over Grand Canyon National Park on June 18, 1986. All 25 passengers and crew on board the two aircraft were killed. It remains the deadliest accident involving a helicopter on United States soil, surpassing the crash of Los Angeles Airways Flight 841 in 1968, which killed 23 people.
On July 7, 2017, an Airbus A320-211 operating as Air Canada Flight 759 was nearly involved in an accident at San Francisco International Airport in San Mateo County, California, United States. The flight, which originated at Toronto Pearson International Airport, had been cleared by air traffic control to land on runway 28R and was on final approach to land on that runway; however, instead of lining up with the runway, the aircraft had lined up with the parallel taxiway, on which four fully loaded and fueled passenger airplanes were stopped awaiting takeoff clearance. The flight crew initiated a go-around prior to landing, after which it landed on 28R without further incident. The aircraft on the taxiway departed for their intended destinations without further incident. The subsequent investigation by the National Transportation Safety Board (NTSB) determined that the Air Canada airplane descended to 59 feet (18 m) above the ground before it began its climb, and that it missed colliding with one of the aircraft on the taxiway by 14 feet (4.3 m).
Aero Country Airport is a privately owned public airport 4 nautical miles (7.4 km) west of the central business district of McKinney, Texas, United States. The airport has no IATA or ICAO designation.
Parker County Airport is a privately owned public airport in Hudson Oaks, Parker County, Texas, United States. The airport serves the city of Weatherford, and is located approximately 5 nautical miles (9.3 km) east of the central business district.
Evergreen International Airlines Flight 17 (4U17/EIA17) was a cargo flight operated by Evergreen International Airlines and flown by a McDonnell Douglas DC-9. On March 18, 1989, the flight's planned route was scheduled to take it from Kelly Air Force Base to Tinker Air Force Base, with a stop at Carswell Air Force Base in Fort Worth, Texas. The two pilots were the only occupants on board. Shortly after taking off from Carswell, the aircraft's main cargo door opened, the crew lost control of the aircraft and it subsequently crashed while attempting an emergency landing, killing both pilots.
Transair Flight 810 was a Boeing 737-200 converted freighter aircraft, owned and operated by Rhoades Aviation under the Transair trade name, on a short cargo flight en route from Honolulu International Airport to Kahului Airport on the neighboring Hawaiian island of Maui. Immediately after an early morning takeoff on July 2, 2021, one of its two Pratt & Whitney JT8D turbofan engines faltered, and the first officer, who was flying the aircraft, reduced power to both engines. The two pilots—the only occupants of the aircraft—began executing the Engine Failure or Shutdown checklist, but became preoccupied with talking to air traffic control (ATC) and performing other flying tasks, never reaching the section of the checklist where the failing engine was to be positively identified and shut down. The captain assumed control but misidentified the failing engine, increased power to that engine, and did not increase power to the other, properly functioning engine. Convinced that neither engine was working properly and unable to maintain altitude with one engine faltering and the other idling, the pilots ditched off the coast of Oahu about 11 minutes into the flight.
In aviation, and in particular in helicopters, servo transparency, is a phenomenon affecting the servomechanisms that assist a helicopter's flight controls, which, in certain flight conditions, can result in a significant stiffening of the controls handled by the pilot. The effect, if not promptly recognised by the pilot, can be hazardous as it can lead to partial or total loss of control, which, if encountered at low altitude, could result in impact with terrain.