Black Hawk (steamboat)

Last updated
Black Hawk steam propeller ad 1851.jpg
Advertisement for steamer Blackhawk.
History
NameBlack Hawk
Operator Jacob Kamm; C.H. Clark & Co.
Route Sacramento River, Willamette River
FateDismantled, 1852
General characteristics
Typeinland shallow draft passenger/freighter/towboat
Length30 ft (9 m)
Beam7 ft (2 m)
Depth3.0 ft (1 m) depth of hold
Installed power steam engine
Propulsionpropeller
NotesIron hull.

Black Hawk was one of three small iron-propeller driven steamboats manufactured in Philadelphia in about 1850 and shipped to the west coast of United States to be placed in river service. The other boats were Eagle and Major Redding . [1] These boats were some of the earliest steamers to operate on the Willamette and Columbia rivers. They could carry about 12 passengers and perhaps a ton of cargo. [2] The boats had to be small to make the run to Oregon City, which passed through the Clackamas rapids a short distance downriver from the town. [2]

Contents

Dimensions

Black Hawk was 30 feet long, with a beam of 7 feet and depth of hold of 3 feet. [1] The boat's tonnage was 10. [1] Tonnage was a measure of volume and not weight.

Sacramento river service

Black Hawk ran on the Sacramento River in 1850 under captain and engineer Jacob Kamm. [3] When Kamm left the vessel in charge of the second engineer, a boiler pump malfunction caused the boiler to overheat and set fire to the boat. [3] Kamm was able to patch up Black Hawk and it could still reach Sacramento, but this was, according to Kamm's remarks in 1911, the swan song of the Black Hawk which was condemned. [3]

Transfer to Oregon

Competition among the early steamboats on the Willamette

In the first year that steamers ran on the Columbia and the Willamette, the strip from Portland to the Falls became infested with boats, all competing for the trade between those places. As it is doubtful whether the two towns together could muster over a couple of thousand inhabitants, pickings for the steamers were slim, and the fight raged furiously between the little propellers Eagle, Black Hawk, and Major Redding, which were joined the next year by the Allan, the Washington, and the pioneer Columbia.

—Randall V. Mills, Sternwheelers Up Columbia (1947) [4]

Black Hawk was brought to Oregon by Capt. Richard Hoyt, Sr. (1814-1862) from San Francisco on the barque Ocean Bird. [5]

Black Hawk arrived at the landing at Oregon City on Sunday, May 18, 1851. [6] There was speculation that Blackhawk could navigate the Tualatin river. [6]

On May 29, 1851, Blackhawk, under Capt. Charles Clark, was making a regular daily run between Oregon City and Portland, departing Oregon City in the morning, and returning the same day from Portland. [7] [8] [9]

An advertisement promised that "strict punctuality, as to the time of starting, will be observed." [7] Also on May 29, 1851, the editor of the Oregon Spectator reported that the captain of the Black Hawk had "chalked our hat", that is, provided the editor free passage on the steamer, on a trip to Portland and back. [10]

On Saturday, May 31, 1851, Black Hawk had to carry the freight and passengers of the new sidewheeler Lot Whitcomb, when the Whitcomb, a much larger vessel, broke a few paddle buckets on one wheel during an excursion to the Cascades Rapids, and as a result had to stop at the foot of the Clackamas Rapids rather than proceeding on to Oregon City. [11]

In June, 1851, Martin Angel, a resident of Oregon City, bought a one-half interest in the Black Hawk. [12]

By June 26, 1851, the boat's management, C.H. Clark & Co., were advertising more specific departure times, 8:00 a.m. from Oregon City, and 2:00 p.m. from Portland, with towing "attended to on short notice." [13]

The water level in the Willamette River fell greatly in the last two weeks of July, 1851. [14] Despite the low level of water, Black Hawk, and another steamboat, the sidewheeler Columbia, were still able to make their runs. [14]

In September 1851, the steamer Black Hawk was taken below the Clackamas Rapids, to be operated on the river away from Oregon City. [15] About November 1, 1851, Black Hawk returned to Oregon City, running a route from there to the Clackamas Rapids and back. [16] The Willamette River was then rising because of fall rains, making steamboat navigation much easier. [17]

Disposition

Black Hawk was dismantled in 1852. [2]

Notes

  1. 1 2 3 "Appendix MM: Steamboats Out of Service". Report of the Chief of Engineers, U. S. Army: Improvement of Rivers and Harbors in Oregon and in Washington Territory. Vol. 2 pt. 3. Washington, DC: U.S. Government Printing Office. 1880. p. 2274.
  2. 1 2 3 Mills, Randall V. (1977). Sternwheelers up Columbia -- A Century of Steamboating in the Oregon Country. Lincoln NE: University of Nebraska (published 1947). pp. 21, 170, 190. ISBN   0-8032-5874-7. LCCN   77007161.
  3. 1 2 3 "Jacob Kamm, 88 Years Old, Recalls Steamboat Days on the Columbia". Sunday Oregonian . Vol. XXX, no. 50. Portland, OR. December 10, 1911. p. 16.
  4. ↑ Mills, Randall V. (1977). Sternwheelers up Columbia -- A Century of Steamboating in the Oregon Country. Lincoln NE: University of Nebraska (published 1947). p. 170. ISBN   0-8032-5874-7. LCCN   77007161.
  5. ↑ Wright, E.W., ed. (1895). Lewis & Dryden's Marine History of the Pacific Northwest. Portland, OR: Lewis and Dryden Printing Co. p. 23, n.7. LCCN   28001147.
  6. 1 2 Schnebly, D.J., ed. (May 22, 1851). "The Black Hawk, a tugboat, arrived at our landing ..." Oregon Spectator . Vol. 5, no. 37. Oregon City, O.T. p. 2, col.1.
  7. 1 2 Schnebly, D.J., ed. (May 29, 1851). "Regular Trips". Oregon Spectator (advertisement). Vol. 5, no. 38. Oregon City, O.T. p. 5, col.3.
  8. ↑ Schnebly, D.J., ed. (June 5, 1851). "The Propeller Black Hawk runs her regular trips ..." Oregon Spectator . Vol. 5, no. 39. Oregon City, O.T. p. 2, col.1.
  9. ↑ Cartwright, Charlotte Moffett (1903). Young, Frederick George (ed.). "Glimpses of Early Days in Oregon". Oregon Historical Quarterly. Salem, OR: Oregon Historical Society. 4.
  10. ↑ Schnebly, D.J., ed. (May 29, 1851). "The captain of the Black Hawk". Oregon Spectator . Vol. 5, no. 38. Oregon City, O.T. p. 2, col.1.
  11. ↑ Schnebly, D.J. (ed.). "The boat returned to Milwaukie on Saturday. ..." Oregon Spectator . Vol. 5, no. 39. Oregon City, O.T. p. 2, col.3.
  12. ↑ Schnebly, D.J., ed. (June 19, 1851). "Our townsman, Martin Angel, as purchased one half ..." Oregon Spectator . Vol. 5, no. 41. Oregon City, O.T.
  13. ↑ Schnebly, D.J., ed. (June 26, 1851). "The Steam Propeller Black Hawk ..." Oregon Spectator . Vol. 5, no. 42. Oregon City, O.T. p. 3, col.3.
  14. 1 2 Schnebly, D.J., ed. (July 29, 1851). "The river has fallen very much ..." Oregon Spectator . Oregon City, O.T. p. 2, col.2.
  15. ↑ Schnebly, D.J., ed. (September 23, 1851). "The Propeller Black Hawk, has been taken below the rapids ..." Oregon Spectator . Vol. 6, no. 3. Oregon City, O.T. p. 2, col.1.
  16. ↑ Schnebly, D.J., ed. (November 4, 1851). "The Black Hawk returned to our landing a few days ago ..." Oregon Spectator . Oregon City, O.T. p. 2, col.3.
  17. ↑ Schnebly, D.J., ed. (November 4, 1851). "Winter is down upon us — the rains have set in in earnest". Oregon Spectator . Oregon City, O.T. p. 2, col.4.

Related Research Articles

Steamboats of the Willamette River

The Willamette River flows northwards down the Willamette Valley until it meets the Columbia River at a point 101 miles from the Pacific Ocean, in the U.S. state of Oregon.

<i>Lot Whitcomb</i> (sidewheeler) First steam-powered craft built on the Willamette River in Oregon, United States

Launched in 1850, Lot Whitcomb, later known as Annie Abernathy, was the first steam-powered craft built on the Willamette River in the U.S. state of Oregon. She was one of the first steam-driven vessels to run on the inland waters of Oregon, and contributed to the rapid economic development of the region.

<i>Gazelle</i> (1854 sidewheeler) American ship

Gazelle was an early sidewheeler on the Willamette River in what is now the U.S. state of Oregon. She did not operate long, suffering a catastrophic boiler explosion on April 8, 1854, less than a month after her trial voyage. This was the worst such explosion ever to occur in the Pacific Northwest states. The wrecked Gazelle was rebuilt and operated for a few years, first briefly as the unpowered barge Sarah Hoyt and then, with boilers installed, as the steamer Señorita. A victim of the explosion was D.P. Fuller, age 28, who is buried in Lone Fir Cemetery in Portland, Oregon.

<i>Washington</i> (steamboat 1851)

Washington was an early steamboat operated in the states of California and Oregon. Washington was built in California and was initially operated on the Sacramento River. In 1851, the steamer was purchased and brought on a ship to the Oregon Territory, where it was operated on the Willamette River until the summer of 1853. Washington was sold again, and then transferred to the Oregon coast, where it operated on the Umpqua River, on the Coquille River and on Coos Bay. Washington was able to operate for shorter distances over the open ocean along the Oregon coast. The steamer was wrecked by a boiler explosion in December 1857, near Scottsburg, O.T., on the Umpqua river.

<i>Elk</i> (sternwheeler 1857)

Elk was a stern-wheel driven steamboat built on the Willamette River in 1857 at Canemah, Oregon. This steamboat is chiefly remembered for its destruction by a boiler explosion in which by good fortune no one was seriously hurt. A folklore tale later arose about this disaster.

<i>Oregona</i> (sternwheeler)

The steamboat Oregona operated on the Willamette River, the Columbia River and the Yamhill River from 1904 to 1936. From 1924 to 1936 this vessel was known as the Interstate.

<i>Elwood</i> (sternwheeler)

Elwood was a sternwheel steamboat which was built to operate on the Willamette River, in Oregon, but which later operated on the Lewis River in Washington, the Stikine River in Canada, and on Puget Sound. The name of this vessel is sometimes seen spelled "Ellwood". Elwood is probably best known for an incident in 1893, when it was approaching the Madison Street Bridge over the Willamette River in Portland, Oregon. The bridge swung open to allow the steamer to pass. However, a streetcar coming in from the east end of the bridge failed to notice the bridge was open, and ran off into the river in the Madison Street Bridge disaster.

<i>Jennie Clark</i> American steamboat

Jennie Clark, also seen spelled Jenny Clark, was the first sternwheel-driven steamboat to operate on the rivers of the Pacific Northwest, including British Columbia. This vessel was commonly known as the Jennie when it was in service. The design of the Jennie Clark set a pattern for all future sternwheel steamboats built in the Pacific Northwest and in British Columbia.

<i>Portland</i> (sidewheeler 1853)

Portland was a side wheel steamer built at Portland, Oregon in the summer of 1853. This vessel was chiefly remembered for its dramatic destruction in 1857 by being washed over Willamette Falls, an incident which killed its captain and a deckhand. The death of the captain, Arthur Jamieson, was one of at least four brothers, all steamboat officers, who were killed in three separate steamboating accidents occurring between 1857 and 1861 in Oregon and in British Columbia.

<i>Wallamet</i> (1853 sidewheeler)

Wallamet was a sidewheel-driven steamboat that operated on the Willamette and Columbia rivers in Oregon and later on the Sacramento and San Joaquin rivers in California. Built in a Mississippi river style that was not suited to the conditions of these rivers, and suffering from construction defects, Wallamet was not a financially successful vessel. The name of this vessel is often seen spelled as Willamette.

Upper Willamette Transportation Line

The Upper Willamette Transportation Line was a line of four inland steamboats that operated from the fall of 1859 to the summer of 1860 on the upper Willamette River in the state of Oregon, United States.

<i>Oregon</i> (sidewheeler 1852)

Oregon was a side-wheel driven steamboat that operated on the Willamette River in the state of Oregon from 1852 to 1854. The steamer was not economically successful and became a total loss by sinking after a short career.

<i>Dayton</i> (sternwheeler)

Dayton was a steamboat which operated on the Willamette and Columbia rivers from 1868 to 1881. Dayton operated on the Willamette from 1868 to 1876, mostly upriver from Willamette Falls, including a route on the Yamhill River to Dayton, Oregon, after which the steamer was named. From 1876 to 1881, Dayton was employed on a run from Portland to Monticello, W.T., which was located on the site of what is now Longview, Washington.

<i>Albany</i> (1868 sternwheeler)

Albany was a stern-wheel driven steamboat that operated on the Willamette River from 1868 to 1875. This vessel should not be confused with the later sternwheeler Albany, which ran, also on the Willamette River, from 1896 to 1906, when it was rebuilt and renamed Georgie Burton.

<i>Occident</i> (sternwheeler)

Occident was a steamer that operated on the Willamette River and occasionally its tributary, the Santiam River from 1875 to about 1890. Occident was designed primarily for freight work, and did not have passenger accommodations. This Occident should not be confused with the smaller steam launch Occident, apparently propeller-driven, which operated out of Astoria, Oregon in the 1890s.

<i>Relief</i> (sternwheeler 1858)

Relief was a stern-wheel driven steamboat that operated on the Willamette River from 1858 to 1865. Relief ran for a short time on the route from Portland to Oregon City, Oregon. After being bought out by the competition, Relief was lined around Willamette Falls to the upper Willamette, where it became the first steamboat to reach Springfield. This vessel should not be confused with a later vessel, also named Relief, which operated on the Columbia and Lewis rivers from 1906 to 1931.

<i>Manzanillo</i> (sternwheeler)

Manzanillo was a stern-wheel driven steamboat built at Portland, Oregon in 1881. Manzanillo was first run on the Columbia River route from Portland to Clatskanie, Oregon and way points along the river. The initial owner of the boat was the People's Freighting Company, but the Shaver family soon acquired control of the vessel, which became the first vessel of what is now Shaver Transportation Company.

<i>Relief</i> (1906 sternwheeler)

Relief was a stern-wheel steamboat that operated on the Columbia and Willamette rivers and their tributaries from 1906 to 1931. Relief had been originally built in 1902, on the Columbia at Blalock, Oregon, in Gilliam County, and launched and operated as Columbia, a much smaller vessel. Relief was used primarily as a freight carrier, first for about ten years in the Inland Empire region of Oregon and Washington, hauling wheat and fruit, and after that was operated on the lower Columbia river.

<i>Undine</i> (Columbia River sternwheeler) American passenger steamboat

Undine was a sternwheel-driven steamboat that operated from 1887 to 1935 on the Columbia and lower Willamette rivers. From 1935 to 1940 the same vessel was operated under the name The Dalles.

<i>Surprise</i> (sternwheeler)

Surprise was a steamboat which operated on the upper Willamette River from 1857 to 1864.

References

Books

On line historic newspaper collections

This page is based on this Wikipedia article
Text is available under the CC BY-SA 4.0 license; additional terms may apply.
Images, videos and audio are available under their respective licenses.