Buckley & Taylor

Last updated
Buckley & Taylor
IndustryEngineering
Founded1861
FounderSamuel Buckley, James Taylor
Defunct1947 (Take over)
SuccessorBrightside Foundry and engineering Co. Ltd., Sheffield
HeadquartersOldham
Number of locations
1 (Castle Ironworks, Greenacres)
ProductsStationary steam engines
Owner1861- Samuel Buckley, James Taylor

Buckley & Taylor was a British engineering company that manufactured stationary steam engines. It was the largest firm of engine makers in Oldham, Lancashire, England. The company produced large steam-driven engines for textile mills in Oldham and exported to India, Holland and Brazil. [1]

Contents

History

Buckley & Taylor started business in 1861 to manufacture beam, horizontal and vertical mill engines and gearing. [2] It began producing mill engines by 1867. Many of their early engines were large compound beam engines. By 1870 they had established a reputation for horizontal twin tandem compounds. Their original 1⁄2-acre (0.20 ha) site at the Castle Ironworks at Green acres expanded to 3 acres (1.2 ha) in 1880, and they operated a forge at Openshaw. In 1890 they were employing 400 men. They built their last engine in 1926. Through Buckley, the firm had a close relationship with the Oldham Boiler Works Ltd. [1] It also often partnered with another Oldham company, Platt Bros, to produce main drives and spinning machines for mills. [2]

Samuel Buckley was born in November 1837 at Hey, Lees, to a mule spinner. [3] He started work in a mill at the age of six. While working he got an education and studied engineering. Before he was twenty he had been appointed chief engineer at Castle Mill and Lowerhouse Mill. He had an interest in politics and was Mayor of Oldham on three occasions: 1883/4 1889/90 and 1890/1. James Taylor was born in 1838 at Shaw, and served an apprenticeship with Woolstenhulmes & Rye. Both men were engineers, though it was Taylor who dealt with the practical details, and Buckley conducted the commercial side of the business. In 1861, the company’s Castle Ironworks was established in Oldham. [2] On Taylor's death, Buckley managed the business alone. It was incorporated in 1902; and Taylor's son William took control. It was taken over by the Brightside Foundry, general engineers of Sheffield in 1947, but continued to operate under its own name. [1]

Horizontal twin tandem

These were 'standard' mill engines preferred by the Oldham Limiteds. An early example was the 1,000-ihp engine delivered to the North Moor spinning company in 1876. The design was conservative, using slide valves and spur wheel gear drive transmission. They did start to fit Corliss valves and rope drives in 1883, but these didn't become standard until the 1890s. An example of such an engine was the 2,000-ihp, horizontal twin tandem triple expansion delivered to Pearl Mill in 1892. [1]

Buckley & Taylor expanded in India sometime in 1865 after it partnered with Platt Bros to build drives and spinning machines for a jute mill in Bombay and, later, in Narayanganj. [2]

Beam Engines

During the 1890s Buckley & Taylor revived the beam engine, building at least 11 engines using designs of JH Tattersall, a consulting engineer from Preston. The two identical engines, twin beam triple expansion engines, built for Nile Mill and Tay Mill were the biggest ever beam engine installed in a cotton mill. They delivered 2,500 ihp and cost over £10,000 [1]

Marine type mill engines

Inverted vertical engines, known commonly as marine type engines, needed less space to operate. From about 1899 Buckley & Taylor started to specialise in this type of engine. Starting with an engine for Don Mill, Middleton, they built 29 of these engines from 1899 to 1916 with a total capacity of 33,000 ihp. They provided a marine type vertical triple expansion engines to Regent Mill, Failsworth, in 1906. It was the largest they built; with 1,800 installed horsepower. The engine had a 63-inch-diameter (1,600 mm) low-pressure cylinder. It was sometimes loaded to 2,000 ihp. It ran until 1958, when it was scrapped. It ran 60,000 spindles. There was a 26-foot (7.9 m) flywheel, 26 ropes operated at 64 rpm. [4]

The company’s steam engines were also preferred by the mills and factories in Brazil. In Minas Gerais, for example, its engines were preferred by these establishments prior to World War I before the transition to electricity in the 1920s. [5]

Mills driven by their engines

Between 1861 and 1926 Buckley & Taylor built more than 200 mill engines with a total capacity of over 160,000 ihp. [1] Arthur Roberts details 26 in his black book. [6] This list is representative rather than complete.

Related Research Articles

<span class="mw-page-title-main">Compound steam engine</span> Steam engine where steam is expanded in stages

A compound steam engine unit is a type of steam engine where steam is expanded in two or more stages. A typical arrangement for a compound engine is that the steam is first expanded in a high-pressure (HP) cylinder, then having given up heat and losing pressure, it exhausts directly into one or more larger-volume low-pressure (LP) cylinders. Multiple-expansion engines employ additional cylinders, of progressively lower pressure, to extract further energy from the steam.

The Stotts were a family of architects from Oldham, North West England, of Scottish descent who specialised in the design of cotton mills. James Stott was the father, Joseph and his elder brother Abraham Stott had rival practices, and in later years did not communicate. Their children continue their practices.

<span class="mw-page-title-main">Regent Mill, Failsworth</span> Cotton mill in Greater Manchester, England

Regent Mill, Failsworth is a Grade II listed former cotton spinning mill in Failsworth, Oldham, Greater Manchester, England. It was built by the Regent Mill Co Ltd. in 1905, and purchased by the Lancashire Cotton Corporation in 1930. It was taken over by the Courtaulds Group in 1964. On ceasing textile production it was occupied by Pifco Ltd, and then by Salton Europe Ltd who now occupy this site. It was driven by an 1800 hp twin tandem compound engine by Buckley & Taylor. It became a ring mill with 60,000 spindles in 1915, all provided by Platt Brothers.

<span class="mw-page-title-main">George Saxon & Co</span> English engineering company

George Saxon & Co was an English engineering company that manufactured stationary steam engines. It was based in the Openshaw district of Manchester. The company produced large steam-driven engines for power stations and later for textile mills in Lancashire and elsewhere.

Woolstenhulmes & Rye was a company that manufactured stationary steam engines. It was based in Oldham, Lancashire, England. The company produced large steam-driven engines for textile mills in Oldham and elsewhere.

Urmson & Thompson was a company that manufactured stationary steam engines. It was based in Oldham, Lancashire, England. The company were general millwrights, also producing some steam engines during the 19th century and after 1904 produced large steam-driven engines for textile mills in Oldham.

Magnet Mill, Chadderton is a cotton spinning mill in Chadderton, Oldham, Greater Manchester. It was built by the Magnet Mill Ltd. in 1902, but purchased by the Lancashire Cotton Corporation in 1935. It was later taken over by the Courtaulds Group. Ceasing textile production in December 1966, it was demolished soon after. A suburban residential estate now occupies this site. It was driven by a 2200 hp twin tandem compound engine by George Saxon & Co, Openshaw, 1903. It had a 27-foot flywheel with 35 ropes, operating at 64½ rpm.

<span class="mw-page-title-main">Blackridings Mill, Oldham</span> Cotton waste mill in Oldham, Greater Manchester, England

Blackridings Mill, Oldham was a cotton waste mill lying off Block Lane in the Werneth area of Oldham, Greater Manchester. It was built before 1861 and ceased spinning between 1875 and 1880. It was then used for flock manufacture and processing cotton waste. It was taken over by the Lancashire Cotton Corporation in the 1930s and passed to Courtaulds in 1964. Production ended in 1973 and the building was demolished in 1975.

<span class="mw-page-title-main">Fox Mill</span>

Fox Mill, Hollinwood is a cotton spinning mill in Hollinwood, Oldham, Greater Manchester. It was taken over by the Lancashire Cotton Corporation in the 1930s and passed to Courtaulds in 1964.

<span class="mw-page-title-main">Kent Mill, Chadderton</span>

Kent Mill, Chadderton was a cotton spinning mill in Chadderton, Oldham, Greater Manchester. It was built in 1908 for the Kent Mill Co. It was taken over by the Lancashire Cotton Corporation in 1938 and passed to Courtaulds in 1964. Production finished in 1991 and it was demolished in 1994.

<span class="mw-page-title-main">Newby Mill, Shaw</span> Cotton mill in Greater Manchester, England

Elm Mill, was a four-storey cotton spinning mill in Shaw and Crompton, Greater Manchester, England. It was built in 1890 for the Elm Spinning Company Ltd., and was called Elm Mill until it closed in 1928. It was revived by the Lancashire Cotton Corporation in 1929 and called Newby Mill. LCC and all their assets passed to Courtaulds in 1964. Production at Newby finished in 1970, and it was used for warehousing. Subsequently, named Shaw No 3 Mill, it became part of Littlewood's Shaw National Distribution Centre. It was demolished to make way for housing in 2022.

<span class="mw-page-title-main">Royd Mill, Oldham</span> Cotton mill in Greater Manchester, England

Royd Mill, Oldham was a cotton spinning mill in Hollinwood, Oldham, Greater Manchester, England. It was built in 1907, and extended in 1912 and 1924. It was taken over by the Lancashire Cotton Corporation in the 1930s and passed to Courtaulds in 1964. Production finished in 1981. The mill was demolished in 2015 to make way for a "DifRent" housing scheme.

<span class="mw-page-title-main">Orme Mill, Waterhead</span> Cotton mill in Greater Manchester, England

Orme Mill, Waterhead is a cotton spinning mill in Waterhead, Oldham, Greater Manchester, England. It was built in 1908. It was taken over by the Lancashire Cotton Corporation in the 1930s and production finished in 1960. The mill was passed on to Ferranti in 1964, and is now in multiple usage.

Majestic Mill, Waterhead is a cotton spinning mill in Waterhead, Oldham, Greater Manchester. It was built in 1903. It was taken over by the Lancashire Cotton Corporation in the 1930s and passed to Courtaulds in 1964, converted to ring spinning in 1971. Production finished in 1982. Still standing in other use.

<span class="mw-page-title-main">Malta Mill, Middleton</span> Cotton mill in Greater Manchester, England

Malta Mill, Middleton is a former cotton spinning mill in the Mills Hill area of Chadderton, Greater Manchester. It lies alongside the Rochdale Canal. It was built in 1904 as a new mule mill, by F. W. Dixon The engine stopped in 1963. The building still stands.

<span class="mw-page-title-main">Junction Mill, Middleton Junction</span> Cotton mill in Greater Manchester, England

Junction Mill, Middleton Junction is a cotton spinning mill at Middleton junction, Chadderton in Greater Manchester alongside the Rochdale Canal.

<span class="mw-page-title-main">John Musgrave & Sons</span>

John Musgrave & Sons was a company that manufactured stationary steam engines. It was founded in 1839 by John Musgrave and his son, Joseph, at the Globe Ironworks, in Bolton, historically in Lancashire, England.

Alexander Petrie and Co was a company that manufactured stationary steam engines. It was based in Rochdale, Greater Manchester in England. The company did general millwrighting, producing some steam engines during the 19th century. Around 1845, their superintendent, William McNaught, was producing large steam-driven beam engines for textile mills in Rochdale.

<span class="mw-page-title-main">J & E Wood</span>

J & E Wood was a company that manufactured stationary steam engines. It was based in the Bolton in Greater Manchester, England. The company produced large steam-driven engines for textile mills in Lancashire and elsewhere.

<span class="mw-page-title-main">Ellenroad Mill</span> Cotton mill in Newhey, Milnrow, Rochdale, England

Ellenroad Mill was a cotton spinning mill in Newhey, a village in the Milnrow area of Rochdale, England. It was built as a mule spinning mill in 1890 by Stott and Sons and extended in 1899. It was destroyed by fire on 19 January 1916. When it was rebuilt, it was designed and equipped as a ring spinning mill.

References

Notes

  1. 1 2 3 4 5 6 Gurr & Hunt 1998 , pp. 16, 17
  2. 1 2 3 4 Lalvani, Kartar (2016). The Making of India: The Untold Story of British Enterprise. London: Bloomsbury Publishing. p. 338. ISBN   978-1-4729-2482-7.
  3. ↑ Eng, Manchester Association of Engineers, Manchester (1912). Transactions - Manchester Association of Engineers. Manchester: Herald & Walker, Printers. pp. xii.
  4. ↑ Roberts 1921
  5. ↑ Eakin, M. (2001). Tropical Capitalism: The Industrialization of Belo Horizonte, Brazil, 1897-1997. Palgrave Macmillan. p. 73. ISBN   978-1-349-62270-2.
  6. ↑ Roberts 1921

Bibliography

This page is based on this Wikipedia article
Text is available under the CC BY-SA 4.0 license; additional terms may apply.
Images, videos and audio are available under their respective licenses.