This article is about "light tubes". For other uses of the phrase "light tubes", see Light tube (disambiguation).
Total external reflection, hollow light tubeTotal internal reflection, block of acrylic
Light tubes (also known as solar pipes, tubular skylights or sun tunnels[1]) are structures that transmit or distribute natural or artificial light for the purpose of illumination and are examples of optical waveguides.
In their application to daylighting, they are also often called tubular daylighting devices, sun pipes, sun scopes, or daylight pipes. They can be divided into two broad categories: hollow structures that contain the light with reflective surfaces; and transparent solids that contain the light by total internal reflection. Principles of nonimaging optics govern the flow of light through them.[2]
Manufacturing custom designed infrared light pipes, hollow waveguides and homogenizers is non-trivial. This is because these are tubes lined with a highly polished infrared reflective coating of gold, which can be applied thick enough to permit these tubes to be used in highly corrosive atmospheres. Carbon black can be applied to certain parts of light pipes to absorb IR light (see photonics). This is done to limit IR light to only certain areas of the pipe.
While most light pipes are produced with a round cross-section, light pipes are not limited to this geometry. Square and hexagonal cross-sections are used in special applications. Hexagonal pipes tend to produce the most homogenized type of IR Light. The pipes do not need to be straight. Bends in the pipe have little effect on efficiency.
The first commercial reflector systems were patented and marketed in the 1850s by Paul Emile Chappuis in London, utilizing various forms of angled mirror designs. Chappuis Ltd's reflectors were in continuous production until the factory was destroyed in 1943.[3] The concept was rediscovered and patented in 1986 by Solatube International of Australia.[4] This system has been marketed for widespread residential and commercial use. Other daylighting products are on the market under various generic names, such as "SunScope", "solar pipe", "light pipe", "light tube", and "tubular skylight".
A tube lined with highly reflective material leads the light rays through a building, starting from an entrance-point located on its roof or one of its outer walls. A light tube is not intended for imaging (in contrast to a periscope, for example); thus image distortions pose no problem and are in many ways encouraged due to the reduction of "directional" light.
The entrance point usually comprises a dome (cupola), which has the function of collecting and reflecting as much sunlight as possible into the tube. Many units also have directional "collectors", "reflectors", or even Fresnel lens devices that assist in collecting additional directional light down the tube.
In 1994, the Windows and Daylighting Group at Lawrence Berkeley National Laboratory (LBNL) developed a series of horizontal light pipe prototypes to increase daylight illuminance at distances of 4.6-9.1 m, to improve the uniformity of daylight distribution and luminance gradient across the room under variable sun and sky conditions throughout the year. The light pipes were designed to passively transport daylighting through relatively small inlet glazing areas by reflecting sunlight to depths greater than conventional sidelight windows or skylights.[5][6]
A set-up in which a laser cutacrylic panel is arranged to redirect sunlight into a horizontally or vertically orientated mirrored pipe, combined with a light spreading system with a triangular arrangement of laser cut panels that spread the light into the room, was developed at the Queensland University of Technology in Brisbane.[7] In 2003, Veronica Garcia Hansen, Ken Yeang, and Ian Edmonds were awarded the Far East Economic Review Innovation Award in bronze for this development.[8][9]
Light transmission efficiency is greatest if the tube is short and straight. In longer, angled, or flexible tubes, part of the light intensity is lost. To minimize losses, a high reflectivity of the tube lining is crucial; manufacturers claim reflectivities of their materials, in the visible range, of up to almost 99.5 percent.[10][11]
At the end point (the point of use), a diffuser spreads the light into the room.
The first full-scale passive horizontal light pipes were built at the Daylight Lab at Texas A&M University, where the annual daylight performance was thoroughly evaluated in a 360 degree rotating 6 m wide by 10 m deep room. The pipe is coated with a 99.3% specular reflective film and the distribution element at the end of the light pipe consists of a 4.6 m long diffusing radial film with an 87% visible transmittance. The light pipe introduces consistently illuminance levels ranging between 300 and 2,500lux throughout the year at distances between 7.6 m to 10 m.[12]
To further optimize the use of solar light, a heliostat can be installed which tracks the movement of the sun, thereby directing sunlight into the light tube at all times of the day as far as the surroundings' limitations allow, possibly with additional mirrors or other reflective elements that influence the light path. The heliostat can be set to capture moonlight at night.
Optical fiber
Optical fibers can also be used for daylighting. A solar lighting system based on plastic optical fibers was in development at Oak Ridge National Laboratory in 2004.[13][14] The system was installed at the American Museum of Science and Energy, Tennessee, USA, in 2005,[15] and brought to market the same year by the company Sunlight Direct.[16][17] However, this system was taken off the market in 2009.
In view of the usually small diameter of the fibers, an efficient daylighting set-up requires a parabolic collector to track the sun and concentrate its light. Optical fibers intended for light transport need to propagate as much light as possible within the core; in contrast, optical fibers intended for light distribution are designed to let part of the light leak through their cladding.[18]
Optical fibers are also used in the Bjork system sold by Parans Solar Lighting AB.[19][20] The optic fibers in this system are made of PMMA (PolyMethyl MethAcrylate) and sheathed with Megolon, a halogen-free thermoplastic resin. A system such as this, however, is quite expensive.[21]
The Parans system[22] consists of three parts. A collector, fiber optic cables, and luminaires spreading the light indoors. One or more collectors are placed on or near the building in a place where they will have good access to direct sunlight. The collector consists of lenses mounted in aluminum profiles with a covering glass as protection. These lenses concentrate sunlight down in the fiber optic cables.
The collectors are modular, which means they come with either 4,6,8,12 or 20 cables depending on the need. Every cable can have an individual length. The fiber optic cables transport the natural light 100 meters (30 floors) in and through the property while retaining both a high level of light quality and light intensity. Examples of implementations are Kastrup Airport, University of Arizona and Stockholm University.
A similar system, but using optical fibers of glass, had earlier been under study in Japan.[23]
Corning Inc. makes Fibrance Light-Diffusing Fiber. Fibrance works by shining a laser through a light-diffusing fiber optic cable. The cable gives off a lighted glow.[24]
A prism light guide was developed in 1981 by Lorne Whitehead, a physics professor at the University of British Columbia,[25][26] and has been used in solar lighting for both the transport and distribution of light.[27][28] A large solar pipe based on the same principle was set up in the narrow courtyard of a 14-floor building of a Washington, D.C. law firm in 2001,[29][30][31][32][33] and a similar proposal has been made for London.[34] A further system has been installed in Berlin.[35]
The 3M company developed a system based on optical lighting film[36] and developed the 3M light pipe,[37] which is a light guide designed to distribute light uniformly over its length, with a thin film incorporating microscopic prisms,[26] which has been marketed in connection with artificial light sources, e.g. sulfur lamps.
In contrast to an optical fiber which has a solid core, a prism light guide leads the light through air and is therefore referred to as a hollow light guide.
The project ARTHELIO,[38][39] partially funded by the European Commission, was an investigation in years 1998 to 2000 into a system for adaptive mixing of solar and artificial light, and which includes a sulfur lamp, a heliostat, and hollow light guides for light transport and distribution.
Disney has experimented with using 3D printing to print internal light guides for illuminated toys.[40]
Fluorescence based system
In a system developed by Fluorosolar and the University of Technology, Sydney, two fluorescent polymer layers in a flat panel capture short wave sunlight, particularly ultraviolet light, generating red and green light, respectively, which is guided into the interior of a building. There, the red and green light is mixed with artificial blue light to yield white light, without infrared or ultraviolet. This system, which collects light without requiring mobile parts such as a heliostat or a parabolic collector, is intended to transfer light to any place within a building.[41][42][43] By capturing ultraviolet, the system can be especially effective on bright but overcast days; this is since ultraviolet is diminished less by cloud cover than are the visible components of sunlight.
Properties and applications
Solar and hybrid lighting systems
A simple light tube, showing the collection, transmission, and distribution
Solar light pipes, compared to conventional skylights and other windows, offer better heat insulation properties and more flexibility for use in inner rooms, but less visual contact with the external environment.
In the context of seasonal affective disorder, it may be worth considering that an additional installation of light tubes increases the amount of natural daily light exposure. It could thus possibly contribute to residents´ or employees´ well-being while avoiding over-illumination effects.
Compared to artificial lights, light tubes have the advantage of providing natural light and of saving energy. The transmitted light varies over the day; should this not be desired, light tubes can be combined with artificial light in a hybrid set-up.[27][44][45][46]
Some artificial light sources are marketed which have a spectrum similar to that of sunlight, at least in the human visible spectrum range,[47][48][49] as well as low flicker.[49] Their spectrum can be made to vary dynamically such as to mimic changes in natural light over the day. Manufacturers and vendors of such light sources claim that their products can provide the same or similar health effects as natural light.[49][50][51] When considered as alternatives to solar light pipes, such products may have lower installation costs but do consume energy during use; therefore they may well be more wasteful in terms of overall energy resources and costs.
On a more practical note, light tubes do not require electric installations or insulation and are thus especially useful for indoor wet areas such as bathrooms and pools. From a more artistic point of view, recent developments, especially those pertaining to transparent light tubes, open new and interesting possibilities for architectural lighting design.[citation needed]
Security applications
Due to the relatively small size and high light output of sun pipes, they have an ideal application to security-oriented situations, such as prisons, police cells, and other locations where restricted access is required. Being of narrow diameter, and not largely affected by internal security grilles, this provides daylight to areas without providing electrical connections or escape access, and without allowing objects to be passed into a secure area.
In electronic devices
Moulded plastic light tubes are commonly used in the electronics industry to direct illumination from LEDs on a circuit board to indicator symbols or buttons. These light tubes typically take on a highly complex shape that uses either gentle curving bends as in an optic fiber or has sharp prismatic folds which reflect off the angled corners. Multiple light tubes are often moulded from a single piece of plastic, permitting easy device assembly since the long thin light tubes are all part of a single rigid component that snaps into place.
Light tube indicators make electronics cheaper to manufacture since the old way would be to mount a tiny lamp into a small socket directly behind the spot to be illuminated. This often requires extensive hand labor for installation and wiring. Light tubes permit all lights to be mounted on a single flat circuit board, but illumination can be directed up, and away from the board wherever it is required.
Color temperature is a parameter describing the color of a visible light source by comparing it to the color of light emitted by an idealized opaque, non-reflective body. The temperature of the ideal emitter that matches the color most closely is defined as the color temperature of the original visible light source. The color temperature scale describes only the color of light emitted by a light source, which may actually be at a different temperature.
In passive solar building design, windows, walls, and floors are made to collect, store, reflect, and distribute solar energy, in the form of heat in the winter and reject solar heat in the summer. This is called passive solar design because, unlike active solar heating systems, it does not involve the use of mechanical and electrical devices.
Daylighting is the practice of placing windows, skylights, other openings, and reflective surfaces so that direct or indirect sunlight can provide effective internal lighting. Particular attention is given to daylighting while designing a building when the aim is to maximize visual comfort or to reduce energy use. Energy savings can be achieved from the reduced use of artificial (electric) lighting or from passive solar heating. Artificial lighting energy use can be reduced by simply installing fewer electric lights where daylight is present or by automatically dimming or switching off electric lights in response to the presence of daylight – a process known as daylight harvesting.
The Advanced Combat Optical Gunsight (ACOG) is a series of prismatic telescopic sights manufactured by Trijicon. The ACOG was originally designed to be used on the M16 rifle and M4 carbine, but Trijicon has also developed ACOG accessories for other firearms. Models provide fixed-power magnification levels from 1.25× to 6×. ACOG reticles are illuminated at night by an internal tritium phosphor. Some versions have an additional daytime reticle illumination via a passive external fiberoptic light pipe or are LED-illuminated using a dry battery. The first ACOG model, known as the TA01, was released in 1987.
A fiberscope is a flexible optical fiber bundle with a lens on one end and an eyepiece or camera on the other. It is used to examine and inspect small, difficult-to-reach places such as the insides of machines, locks, and the human body.
A solar thermal collector collects heat by absorbing sunlight. The term "solar collector" commonly refers to a device for solar hot water heating, but may refer to large power generating installations such as solar parabolic troughs and solar towers or non-water heating devices such as solar cookers or solar air heaters.
A heliostat is a device that includes a mirror, usually a plane mirror, which turns so as to keep reflecting sunlight toward a predetermined target, compensating for the Sun's apparent motions in the sky.
A solar mirror contains a substrate with a reflective layer for reflecting the solar energy, and in most cases an interference layer. This may be a planar mirror or parabolic arrays of solar mirrors used to achieve a substantially concentrated reflection factor for solar energy systems.
Architectural lighting design is a field of work or study that is concerned with the design of lighting systems within the built environment, both interior and exterior. It can include manipulation and design of both daylight and electric light or both, to serve human needs.
The sulfur lamp is a highly efficient full-spectrum electrodeless lighting system whose light is generated by sulfur plasma that has been excited by microwave radiation. They are a particular type of plasma lamp, and one of the most modern. The technology was developed in the early 1990s and appeared promising, but was not a commercial success by the late 1990s. Since 2005, lamps are again being manufactured for commercial use.
Daylight is the combination of all direct and indirect sunlight during the daytime. This includes direct sunlight, diffuse sky radiation, and (often) both of these reflected by Earth and terrestrial objects, like landforms and buildings. Sunlight scattered or reflected by astronomical objects is generally not considered daylight. Therefore, daylight excludes moonlight, despite it being reflected indirect sunlight.
Nonimaging optics is a branch of optics that is concerned with the optimal transfer of light radiation between a source and a target. Unlike traditional imaging optics, the techniques involved do not attempt to form an image of the source; instead an optimized optical system for optimal radiative transfer from a source to a target is desired.
A solar tracker is a device that orients a payload toward the Sun. Payloads are usually solar panels, parabolic troughs, Fresnel reflectors, lenses, or the mirrors of a heliostat.
Anidolic lighting systems use anidolic optical components to light rooms. Light redirected by these systems does not converge to a focal point or form an image, hence the name.
Hybrid solar lighting (HSL) or hybrid lighting systems combine the use of solar with artificial light for interior illumination by channelling sunlight through fiber optic cable bundles to provide solar light into rooms without windows or skylights, and by supplementing this natural light with artificial light—typically LED—as required.
Practical Solar, Inc. is an American manufacturer of heliostats used for concentrating solar power, as well as for residential and commercial natural lighting (daylighting) applications. The company, located in Boston, Massachusetts, introduced its heliostat system for sale in February 2009. According to the detailed agenda for the 5th Annual Conference on Clean Energy in Boston, Practical Solar’s chief operating officer David Howell made a presentation seeking funding for the company at the “Investor Pitch Session” on November 12, 2009.
A skylight is a light-permitting structure or window, usually made of transparent or translucent glass, that forms all or part of the roof space of a building for daylighting and ventilation purposes.
The following outline is provided as an overview of and topical guide to solar energy:
Remote Skylights are optical systems capable of providing natural light to unlit locations. An arrangement of parabolic reflectors and optical fiber cables, transport natural sunlight to areas that would otherwise be dark or be lit artificially.
Photopia Optical Design Software (Photopia) is a commercial optical engineering ray-tracing software program for the design and analysis of non-imaging optical systems. Photopia is written and distributed by LTI Optics, LLC and was first released in 1996. Photopia's main market is the architectural lighting industry but it is also used in the automotive, medical, industrial, signal and consumer products industries. Photopia includes a full library of lamps including the latest high brightness LEDs as well as a library of material BSDF data.
↑ "MIRO LIGHTPIPE". Archived from the original on November 14, 2006. Retrieved 2006-08-01.{{cite web}}: CS1 maint: bot: original URL status unknown (link)
↑ "Archived copy"(PDF) (in German). Archived(PDF) from the original on 2006-09-28. Retrieved 2006-08-03.{{cite web}}: CS1 maint: archived copy as title (link)
(in German) Alexander Rosemann: Hohllichtleiter für Tageslichtnutzung. Pflaum Verlag, München 2002. ISBN3-7905-0862-4
Jenkins, David; Muneer, Tariq; Kubie, Jorge (2005), "A design tool for predicting the performances of light pipes", Energy and Buildings, 37 (5): 485, doi:10.1016/j.enbuild.2004.09.014
UK based Monodraught SunPipe (and www.sunpipe.info) with extensive technical and reference information
This page is based on this Wikipedia article Text is available under the CC BY-SA 4.0 license; additional terms may apply. Images, videos and audio are available under their respective licenses.
