Low-noise amplifier

Last updated

A low-noise amplifier (LNA) is an electronic component that amplifies a very low-power signal without significantly degrading its signal-to-noise ratio (SNR). Any electronic amplifier will increase the power of both the signal and the noise present at its input, but the amplifier will also introduce some additional noise. LNAs are designed to minimize that additional noise, by choosing special components, operating points, and circuit topologies. Minimizing additional noise must balance with other design goals such as power gain and impedance matching.

Contents

LNAs are found in radio communications systems, Amateur Radio stations, medical instruments and electronic test equipment. A typical LNA may supply a power gain of 100 (20  decibels (dB)) while decreasing the SNR by less than a factor of two (a 3 dB noise figure (NF)). Although LNAs are primarily concerned with weak signals that are just above the noise floor, they must also consider the presence of larger signals that cause intermodulation distortion.

Communications

Antennas are a common source of weak signals. [1] An outdoor antenna is often connected to its receiver by a transmission line called a feed line . Losses in the feed line lower the received signal-to-noise ratio: a feed line loss of 3 dB degrades the receiver signal-to-noise ratio (SNR) by 3 dB.

An example is a feed line made from 10 feet (3.0 m) of RG-174 coaxial cable and used with a global positioning system (GPS) receiver. The loss in that feed line is 3.2 dB at 1  GHz ; approximately 5 dB at the GPS frequency (1.57542 GHz). This feed line loss can be avoided by placing an LNA at the antenna, which supplies enough gain to offset the loss.

An LNA is a key component at the front-end of a radio receiver circuit to help reduce unwanted noise in particular. Friis' formulas for noise models the noise in a multi-stage signal collection circuit. In most receivers, the overall NF is dominated by the first few stages of the RF front end.

By using an LNA close to the signal source, the effect of noise from subsequent stages of the receive chain in the circuit is reduced by the signal gain created by the LNA, while the noise created by the LNA itself is injected directly into the received signal. The LNA boosts the desired signals' power while adding as little noise and distortion as possible. The work done by the LNA enables optimum retrieval of the desired signal in the later stages of the system.

Design considerations

Low noise amplifiers are the building blocks of communication systems and instruments. The most important LNA specifications or attributes are: [2]

A good LNA has a low NF (e.g. 1 dB), enough gain to boost the signal (e.g. 10 dB) and a large enough inter-modulation and compression point (IP3 and P1dB) to do the work required of it. Further specifications are the LNA's operating bandwidth, gain flatness, stability, input and output voltage standing wave ratio (VSWR).

For low noise, a high amplification is required for the amplifier in the first stage. Therefore, junction field-effect transistors (JFETs) and high-electron-mobility transistors (HEMTs) are often used. They are driven in a high-current regime, which is not energy-efficient but reduces the relative amount of shot noise. It also requires input and output impedance matching circuits for narrow-band circuits to enhance the gain (see Gain-bandwidth product ).

Gain

Amplifiers need a device to provide gain. In the 1940s, that device was a vacuum tube, but now it is usually a transistor. The transistor may be one of many varieties of bipolar transistors or field-effect transistors. Other devices producing gain, such as tunnel diodes, may be used.

Broadly speaking, two categories of transistor models are used in LNA design: Small-signal models use quasi-linear models of noise and large-signal models consider non-linear mixing.

The amount of gain applied is often a compromise. On the one hand, high gain makes weak signals strong. On the other hand, high gain means higher-level signals, and such high-level signals with high gain may exceed the amplifier's dynamic range or cause other types of noise such as harmonic distortion or nonlinear mixing.

Noise figure

The noise figure helps determine the efficiency of a particular LNA. LNA suitability for a particular application is typically based on its noise figure. In general, a low noise figure results in better signal reception.

Impedance

The circuit topology affects input and output impedance. In general, the source impedance is matched to the input impedance because that will maximize the power transfer from the source to the device. If the source impedance is low, then a common base or common gate circuit topology may be appropriate. For a medium source impedance, a common emitter or common source topology may be used. With a high source resistance, a common collector or common drain topology may be appropriate. An input impedance match may not produce the lowest noise figure.

Biasing

Another design issue is the noise introduced by biasing networks. In communication circuits, biasing networks play a critical role in establishing stable operating points for active components, but they also introduce noise. The primary types of noise introduced by these networks are thermal noise and flicker noise. Thermal noise arises from resistive elements in the network, which is inevitable as any resistive component generates noise due to the random motion of charge carriers. This type of noise is especially problematic at high frequencies. Flicker noise, also known as 1/f noise, is related to the current flow through devices like transistors and becomes more significant at lower frequencies. [3]

For instance, in low-noise amplifiers (LNA), the biasing network must be carefully designed to minimize the impact of noise on the overall performance. Improper biasing can lead to increased noise figures, compromising the signal-to-noise ratio and degrading communication system performance. The design and selection of components within the bias network are therefore crucial to ensuring low-noise operation, particularly in systems that rely on amplifying weak signals. [4]

In addition, matching networks and careful biasing techniques, such as using low-noise transistors and optimizing impedance matching, help mitigate the noise effects introduced by bias circuits

Applications

LNAs are used in communications receivers such as in radio telescopes, cellular telephones, GPS receivers, wireless LANs (WiFi), and satellite communications.

In a satellite communications system, the ground station receiving antenna uses an LNA because the received signal is weak since satellites have limited power and therefore use low-power transmitters. The satellites are also distant and suffer path loss: low Earth orbit satellites might be 120 miles (190 km) away; a geosynchronous satellite is 22,236 miles (35,785 km) away.

The LNA boosts the antenna signal to overcome feed line losses between the antenna and the receiver.

LNAs can enhance the performance of software-defined radio (SDR) receiver systems. SDRs are typically designed to be general purpose and therefore the noise figure is not optimized for any one particular application. With an LNA and appropriate filter, performance is improved over a range of frequencies.

See also

Related Research Articles

In electronics, the figures of merit of an amplifier are numerical measures that characterize its properties and performance. Figures of merit can be given as a list of specifications that include properties such as gain, bandwidth, noise and linearity, among others listed in this article. Figures of merit are important for determining the suitability of a particular amplifier for an intended use.

<span class="mw-page-title-main">Amplifier</span> Electronic device/component that increases the strength of a signal

An amplifier, electronic amplifier or (informally) amp is an electronic device that can increase the magnitude of a signal. It is a two-port electronic circuit that uses electric power from a power supply to increase the amplitude of a signal applied to its input terminals, producing a proportionally greater amplitude signal at its output. The amount of amplification provided by an amplifier is measured by its gain: the ratio of output voltage, current, or power to input. An amplifier is defined as a circuit that has a power gain greater than one.

<span class="mw-page-title-main">Operational amplifier</span> High-gain voltage amplifier with a differential input

An operational amplifier is a DC-coupled electronic voltage amplifier with a differential input, a (usually) single-ended output, and an extremely high gain. Its name comes from its original use of performing mathematical operations in analog computers.

<span class="mw-page-title-main">Negative-feedback amplifier</span> Type of electronic amplifier

A negative-feedback amplifier is an electronic amplifier that subtracts a fraction of its output from its input, so that negative feedback opposes the original signal. The applied negative feedback can improve its performance and reduces sensitivity to parameter variations due to manufacturing or environment. Because of these advantages, many amplifiers and control systems use negative feedback.

This is an index of articles relating to electronics and electricity or natural electricity and things that run on electricity and things that use or conduct electricity.

<span class="mw-page-title-main">Valve amplifier</span> Type of electronic amplifier

A valve amplifier or tube amplifier is a type of electronic amplifier that uses vacuum tubes to increase the amplitude or power of a signal. Low to medium power valve amplifiers for frequencies below the microwaves were largely replaced by solid state amplifiers in the 1960s and 1970s. Valve amplifiers can be used for applications such as guitar amplifiers, satellite transponders such as DirecTV and GPS, high quality stereo amplifiers, military applications and very high power radio and UHF television transmitters.

<span class="mw-page-title-main">Preamplifier</span> Electronic amplifier that converts weak signal into strong signal

A preamplifier, also known as a preamp, is an electronic amplifier that converts a weak electrical signal into an output signal strong enough to be noise-tolerant and strong enough for further processing, or for sending to a power amplifier and a loudspeaker. Without this, the final signal would be noisy or distorted. They are typically used to amplify signals from analog sensors such as microphones and pickups. Because of this, the preamplifier is often placed close to the sensor to reduce the effects of noise and interference.

<span class="mw-page-title-main">Common emitter</span> Type of electronic amplifier using a bipolar junction transistor

In electronics, a common-emitter amplifier is one of three basic single-stage bipolar-junction-transistor (BJT) amplifier topologies, typically used as a voltage amplifier. It offers high current gain, medium input resistance and a high output resistance. The output of a common emitter amplifier is inverted; i.e. for a sine wave input signal, the output signal is 180 degrees out of phase with respect to the input.

An antenna tuner, a matchbox, transmatch, antenna tuning unit (ATU), antenna coupler, or feedline coupler is a device connected between a radio transmitter or receiver and its antenna to improve power transfer between them by matching the impedance of the radio to the antenna's feedline. Antenna tuners are particularly important for use with transmitters. Transmitters feed power into a resistive load, very often 50 ohms, for which the transmitter is optimally designed for power output, efficiency, and low distortion. If the load seen by the transmitter departs from this design value due to improper tuning of the antenna/feedline combination the power output will change, distortion may occur and the transmitter may overheat.

<span class="mw-page-title-main">Input impedance</span> Measure of the opposition to current flow by an external electrical load

In electrical engineering, the input impedance of an electrical network is the measure of the opposition to current (impedance), both static (resistance) and dynamic (reactance), into a load network that is external to the electrical source network. The input admittance is a measure of the load network's propensity to draw current. The source network is the portion of the network that transmits power, and the load network is the portion of the network that consumes power.

<span class="mw-page-title-main">Common gate</span> Electronic amplifier circuit type

In electronics, a common-gate amplifier is one of three basic single-stage field-effect transistor (FET) amplifier topologies, typically used as a current buffer or voltage amplifier. In this circuit, the source terminal of the transistor serves as the input, the drain is the output, and the gate is connected to some DC biasing voltage, or "common," hence its name. The analogous bipolar junction transistor circuit is the common-base amplifier.

The cascode is a two-stage amplifier that consists of a common emitter stage feeding into a common base stage when using bipolar junction transistors (BJTs) or alternatively a common source stage feeding a common gate stage when using field-effect transistors (FETs).

This article illustrates some typical operational amplifier applications. A non-ideal operational amplifier's equivalent circuit has a finite input impedance, a non-zero output impedance, and a finite gain. A real op-amp has a number of non-ideal features as shown in the diagram, but here a simplified schematic notation is used, many details such as device selection and power supply connections are not shown. Operational amplifiers are optimised for use with negative feedback, and this article discusses only negative-feedback applications. When positive feedback is required, a comparator is usually more appropriate. See Comparator applications for further information.

A radio transmitter or receiver is connected to an antenna which emits or receives the radio waves. The antenna feed system or antenna feed is the cable or conductor, and other associated equipment, which connects the transmitter or receiver with the antenna and makes the two devices compatible. In a radio transmitter, the transmitter generates an alternating current of radio frequency, and the feed system feeds the current to the antenna, which converts the power in the current to radio waves. In a radio receiver, the incoming radio waves excite tiny alternating currents in the antenna, and the feed system delivers this current to the receiver, which processes the signal.

Gain compression is a reduction in differential or slope gain caused by nonlinearity of the transfer function of an amplifying device for large-signal inputs.

<span class="mw-page-title-main">RF power amplifier</span> Type of electronic amplifier

A radio-frequency power amplifier is a type of electronic amplifier that converts a low-power radio-frequency (RF) signal into a higher-power signal. Typically, RF power amplifiers are used in the final stage of a radio transmitter, their output driving the antenna. Design goals often include gain, power output, bandwidth, power efficiency, linearity, input and output impedance matching, and heat dissipation.

<span class="mw-page-title-main">Valve RF amplifier</span> Device for electrically amplifying the power of an electrical radio frequency signal

A valve RF amplifier or tube amplifier (U.S.) is a device for electrically amplifying the power of an electrical radio frequency signal.

Technical specifications and detailed information on the valve audio amplifier, including its development history.

<span class="mw-page-title-main">Tube sound</span> Characteristic quality of sounds from vacuum tube amplifiers

Tube sound is the characteristic sound associated with a vacuum tube amplifier, a vacuum tube-based audio amplifier. At first, the concept of tube sound did not exist, because practically all electronic amplification of audio signals was done with vacuum tubes and other comparable methods were not known or used. After introduction of solid state amplifiers, tube sound appeared as the logical complement of transistor sound, which had some negative connotations due to crossover distortion in early transistor amplifiers. However, solid state amplifiers have been developed to be flawless and the sound is later regarded neutral compared to tube amplifiers. Thus the tube sound now means 'euphonic distortion.' The audible significance of tube amplification on audio signals is a subject of continuing debate among audio enthusiasts.

The Blackmer gain cell is an audio frequency voltage-controlled amplifier (VCA) circuit with an exponential control law. It was invented and patented by David E. Blackmer between 1970 and 1973. The four-transistor core of the original Blackmer cell contains two complementary bipolar current mirrors that perform log-antilog operations on input voltages in a push-pull, alternating fashion. Earlier log-antilog modulators using the fundamental exponential characteristic of a p–n junction were unipolar; Blackmer's application of push-pull signal processing allowed modulation of bipolar voltages and bidirectional currents.

References

  1. ↑ A 900MHz Low Noise Amplifier with Temperature Compensated Biasing. January 1, 2008. ISBN   9780549667391.
  2. ↑ "An Introduction to Low Noise Amplifier Specifications". Software-Defined Radio Simplified. January 11, 2020. Retrieved January 11, 2020.
  3. ↑ Honnaiah, Puneeth Jubba; Reddy, Shridhar (December 30, 2019), Design of a Low Noise Amplifier, arXiv: 1912.13029 , retrieved September 16, 2024
  4. ↑ Zhao, Jinxiang; Wang, Feng; Yu, Hanchao; Zhang, Shengli; Wang, Kuisong; Liu, Chang; Wan, Jing; Liang, Xiaoxin; Yan, Yuepeng (February 18, 2022). "Analysis and Design of a Wideband Low-Noise Amplifier with Bias and Parasitic Parameters Derived Wide Bandpass Matching Networks". Electronics. 11 (4): 633. doi: 10.3390/electronics11040633 . ISSN   2079-9292.

Further reading

This page is based on this Wikipedia article
Text is available under the CC BY-SA 4.0 license; additional terms may apply.
Images, videos and audio are available under their respective licenses.