Minnehaha (sternwheeler)

Last updated
Minnehaha auction ad 1871.jpg
Advertisement for auction of Minnehaha, September 4, 1871
History
Name:Minnehaha
Route: Oswego Lake, Willamette River
Maiden voyage: October 24, 1866
Identification: U.S. 90084
General characteristics
Type: inland steamboat
Length: 70 ft (21.3 m) exclusive of fantail.
Beam: 16 ft (4.9 m) exclusive of guards
Depth: 3 ft (1 m) 3.5 ft (1 m) or depth of hold
Installed power: twin steam engines, horizontally mounted, single cylinder, bore 8.5 in (215.90 mm), stroke 18 in (457.20 mm).
Propulsion: stern-wheel

Minnehaha was a sternwheel-driven steamboat which was built in 1866 on Oswego Lake, then known as Sucker Lake, in Oregon, United States. Minnehaha was later transferred to the Willamette and Columbia rivers where it operated for the first part of the 1870s.

Contents

Construction

John C. Trullinger (b.1828) built the Minnehaha on the eastern or "upper" end of Sucker Lake, near a sawmill owned by the Oswego Milling Company. [1] [2]

Engineering

Minnehaha was driven by a stern-wheel, which was turned by twin steam engines removed from the steam scow Skedaddle, which had been built in 1862 on the Tualatin River. [1]

The size of the engines has been variously reported. An 1871 source states that each engine had an internal cylinder diameter, called a "bore" of 8.5 in (215.90 mm) and the distance traveled by the piston, called the "stroke" of 18 in (457.20 mm). [3]

Minnehaha had a locomotive-type boiler 14 feet long, which was described as "nearly new" in September 1871. [3] The size of the firebox was reported to have been 4.5 feet by 3 feet. [3]

Dimensions

Minnehaha was 70 ft (21.3 m) long, exclusive of the extension of the main deck over the stern, called the fantail, on which the stern-wheel was mounted. [2]

The beam (width) of Minnehaha was 16 ft (4.9 m) exclusive of the protective timbers along the upper sides of the hull, called the guards. [2] The depth of hold was 3 ft (1 m)3.5 ft (1 m). [2]

In 1874, Minnehaha measured out at 103.63 gross tons, which was a measure of volume and not weight. [4] The official merchant registry number in 1874 was 90084. [4]

Operations

Other steamers on the lake

Minnehaha was the only steamer ever launched upon Sucker Lake. [1] However, Minnehaha was not the only steam vessel ever to operate on the lake; the others were built on the Tualatin River and transferred to the lake.

The small (20 gross tons) Henrietta operating on the lake in 1870. [5] The much larger sternwheeler Onward made at least one trip on Sucker Lake, on January 21, 1873, reaching the lake from the Tualatin through a canal which had recently been completed on the west, or "upper" end of the lake. [6]

Sucker Lake service

Minnehaha made its trial trip on October 24, 1866, under Captain Richard Copely. [1]

In October 1866, Minnehaha became part of a transportation route to Washington County, Oregon which sought to avoid the navigation barrier then formed by Willamette Falls. [7]

According to a contemporaneous report, the plan for the route would be that the Senator would run to Oswego, on the Willamette River, where passengers would disembark, and cross over to Sucker Lake, as Lake Oswego was then known, and board Minnehaha. [7]

The lake boat then paddled across the water to the lake’s western end, where it was reported, passengers would be taken to Colfax, on the Tualatin River "by cars". [7] Once at Colfax, the steamer Yamhill, with Captain Kellogg in charge, would "be in readiness." [7]

The Yamhill would then steam up the Tualatin River, with, it was projected, excursionists, as far as Taylor’s Bridge. [7] Taylor Bridge was about six miles upriver from Colfax. [8]

While it earned some praise in a newspaper of the time, [9] this route proved to have many problems in practice:

… the passenger was made dizzy by the number of changes and interruptions in the journey. He landed from the Portland boat at what is now Oswego. shinnied up the bank to the lake, and there found a tiny steamboat, the Minnehaha, waiting for him. He boarded it to ride the few miles across the lake to the railroad. There he found a tramway, with the usual five foot gauge, on which were platform cars ten feet long and eight wide, each drawn by two horses. He could ride one if he wished, but it was hardly worth the effort, for it was only a mile and a half to the Tualatin River. There the Onward waited to make its weekly trip up the Tualatin … [10]

Minnehaha was continuing to run on Sucker Lake on February 11, 1869. [8]

Transfer to Willamette River

It was possible to bring a steamboat down Sucker Creek from Sucker Creek to the Willamette River, if appropriate measures were taken, including the building of a coffer dam in the abandoned mill race. [6] James D. Miller did this with the Onward. [6]

With the Oswego–Tualatin canal not completed until 1872, [6] a similar procedure would likely have had to have been followed, between February 11, 1869 and early September 1871, to bring Minnehaha to the Willamette River.

Sale at Auction

In September 1871, Minnehaha was sold at auction, either by the sheriff [11] or, more likely, by A.B. Richardson, auctioneer. [3] The auction was conducted on the Minnehaha itself, at the dock at the foot of Morrison Street in Portland, Oregon. [3] The purchaser at the auction was Barney Train, of East Portland. [11]

Willamette and Columbia river service

In 1874, Minnehaha was engaged in light towing service on the lower Willamette and Columbia rivers. [12]

Disposition

Minnehaha was dismantled in 1876 at Portland. [13]

Notes

  1. 1 2 3 4 Wright, E.W., ed. (1895). "Chapter 7: The "Brother Jonathan" and Other Notable Wrecks, Steamboating on Interior Waters". Lewis & Dryden's Marine History of the Pacific Northwest. Portland, OR: Lewis and Dryden Printing Co. pp. 146–147. LCCN   28001147.
  2. 1 2 3 4 Corning, Howard McKinley (1973). "Other Landings of a Bygone Day …Old Oswego and the Lower Tualatin". Willamette Landings -- Ghost Towns of the River (2nd ed.). Portland, OR: Oregon Historical Society. pp. 172–173. ISBN   0875950426.
  3. 1 2 3 4 5 "Special Auction Sale on THE STEAMBOAT "MINNEHAHA"". Morning Oregonian (notice for auction to be held on Thursday, Sept. 7, 1871). 11 (154). Portland, OR: Henry L. Pittock. Sep 4, 1871. p.2, col.7.
  4. 1 2 U.S. Treasury Dept, Statistics Bureau (1875). Annual List of Merchant Vessels (FY end Jun 30, 1874). 7. Wash. DC: GPO. p. 235. hdl:2027/njp.32101068130820.
  5. U.S. Steamboat Inspection Service; Board of Supervising Inspectors (1870). Proceedings of the Annual Meeting of the Board. 18. Wash. DC: GPO. p. 96.
  6. 1 2 3 4 Farnell, James E. (1978). "Steamboat Navigation". Tualatin River Navigability Study. Salem, OR: State of Oregon, Division of State Lands. pp. 25–27.
  7. 1 2 3 4 5 "COLFAX.—A basket excursion is thought of, to take place soon, on the new line of transportation from Oswego". Oregon City Enterprise. 1 (1). D.C. Ireland. Oct 27, 1866. p.3, col.1.
  8. 1 2 Farnell, James E. (1978). "Steamboat Navigation". Tualatin River Navigability Study. Salem, OR: State of Oregon, Division of State Lands. pp. 21–22.
  9. "TOWN AND COUNTY … Mr. John T. Scott, of Forest Grove, Washington County, visited Oregon City …". The Weekly Enterprise. 3 (14). Oregon City, OR: D.C. Ireland. Feb 13, 1869. p.3, col.2.
  10. Mills, Randall V. (1947). "Chapter 6: The Portages". Sternwheelers up Columbia -- A Century of Steamboating in the Oregon Country. Lincoln NE: University of Nebraska. p. 73. ISBN   0-8032-5874-7. LCCN   77007161.
  11. 1 2 Wright, E.W., ed. (1895). "Chapter 9: Remarkable Trip of the "Shoshone," Willamette and Columbia Transportation Enterprises". Lewis & Dryden's Marine History of the Pacific Northwest. Portland, OR: Lewis and Dryden Printing Co. p. 197. LCCN   28001147.
  12. Wright, E.W., ed. (1895). "Chapter 10: Willamette Locks Completed, Charter Rates of the Lumber Fleet". Lewis & Dryden's Marine History of the Pacific Northwest. Portland, OR: Lewis and Dryden Printing Co. p. 207. LCCN   28001147.
  13. Affleck, Edward L. (2000). "Part One: Chapter Two: Columbia River Waterways -- List of Vessels". A Century of Paddlewheelers in the Pacific Northwest, the Yukon, and Alaska. Vancouver, BC: Alexander Nicholls Press. p. 19. ISBN   0-920034-08-X.

Related Research Articles

Steamboats of the Willamette River

The Willamette River flows northwards down the Willamette Valley until it meets the Columbia River at a point 101 miles from the Pacific Ocean, in the U.S. state of Oregon.

<i>Lot Whitcomb</i> (sidewheeler) First steam-powered craft built on the Willamette River in Oregon, United States

Launched in 1850, Lot Whitcomb, later known as Annie Abernathy, was the first steam-powered craft built on the Willamette River in the U.S. state of Oregon. She was one of the first steam-driven vessels to run on the inland waters of Oregon, and contributed to the rapid economic development of the region.

<i>Elk</i> (sternwheeler 1857) 1857 ship

Elk was a stern-wheel driven steamboat built on the Willamette River in 1857 at Canemah, Oregon. This steamboat is chiefly remembered for its destruction by a boiler explosion in which by good fortune no one was seriously hurt. A folklore tale later arose about this disaster.

<i>Jennie Clark</i>

Jennie Clark, also seen spelled Jenny Clark, was the first sternwheel-driven steamboat to operate on the rivers of the Pacific Northwest, including British Columbia. This vessel was commonly known as the Jennie when it was in service. The design of the Jennie Clark set a pattern for all future sternwheel steamboats built in the Pacific Northwest and in British Columbia.

<i>Portland</i> (sidewheeler 1853) side wheel steamer

Portland was a side wheel steamer built at Portland, Oregon in the summer of 1853. This vessel was chiefly remembered for its dramatic destruction in 1857 by being washed over Willamette Falls, an incident which killed its captain and a deckhand. The death of the captain, Arthur Jamieson, was one of at least four brothers, all steamboat officers, who were killed in three separate steamboating accidents occurring between 1857 and 1861 in Oregon and in British Columbia.

<i>Black Hawk</i> (steamboat) steamboat

Black Hawk was one of three small iron-propeller driven steamboats manufactured in Philadelphia in about 1850 and shipped to the west coast of United States to be placed in river service. The other boats were Eagle and Major Redding. These boats were some of the earliest steamers to operate on the Willamette and Columbia rivers. They could carry about 12 passengers and perhaps a ton of cargo. The boats had to be small to make the run to Oregon City, which passed through the Clackamas rapids a short distance downriver from the town.

Peoples Transportation Company

The People's Transportation Company operated steamboats on the Willamette River and its tributaries, the Yamhill and Tualatin rivers, in the State of Oregon from 1862 to 1871. For a brief time this company operated steamers on the Columbia River, and for about two months in 1864, the company operated a small steamer on the Clackamas River.

<i>Shoo Fly</i> (sternwheeler) sternwheel-driven steamboat

Shoo Fly was a sternwheel-driven steamboat that operated on the Willamette and Columbia rivers in the 1870s. Originally built as primarily as a freight boat, the vessel was used in other roles, including towing and clearing of snags. Shoo Fly inspired the name of another sternwheeler on the Willamette River, Don't Bother Me.

Upper Willamette Transportation Line

The Upper Willamette Transportation Line was a line of four inland steamboats that operated from the fall of 1859 to the summer of 1860 on the upper Willamette River in the state of Oregon.

<i>James Clinton</i> (sternwheeler)

James Clinton was a steamboat which operated on the upper Willamette River from 1856 to 1861. Although the Clinton was said to have been "not a very good boat.", it was the first steamer ever to reach Eugene, Oregon. James Clinton was destroyed in April 1861, when a large fire broke out at Linn City, Oregon in a shoreside structure near to where the vessel was moored.

<i>Oregon</i> (sidewheeler 1852)

Oregon was a side-wheel driven steamboat that operated on the Willamette River in the state of Oregon from 1852 to 1854. The steamer was not economically successful and became a total loss by sinking after a short career.

<i>Dayton</i> (sternwheeler) steamboat operated on Willamette and Columbia rivers from 1868 to 1881

Dayton was a steamboat which operated on the Willamette and Columbia rivers from 1868 to 1881. Dayton operated on the Willamette from 1868 to 1876, mostly upriver from Willamette Falls, including a route on the Yamhill River to Dayton, Oregon, after which the steamer was named. From 1876 to 1881, Dayton was employed on a run from Portland to Monticello, W.T., which was located on the site of what is now Longview, Washington.

<i>Senator</i> (sternwheeler)

Senator was a stern-wheel-driven steamboat which operated on the Willamette River in the state of Oregon from 1863 to 1875. Senator is chiefly remembered for its having been destroyed in a fatal boiler explosion in 1875 while making a landing at the Portland, Oregon waterfront in 1875.

<i>Albany</i> (sternwheeler 1868) stern-wheel driven steamboat

Albany was a stern-wheel driven steamboat that operated on the Willamette River from 1868 to 1875. This vessel should not be confused with the later sternwheeler Albany, which ran, also on the Willamette River, from 1896 to 1906, when it was rebuilt and renamed Georgie Burton.

<i>Onward</i> (sternwheeler 1867)

Onward was a stern-wheel driven steamboat that operated on the Tualatin River from 1867 to 1873, on Sucker Lake, now known as Oswego Lake, from 1873 to 1874, on the Cowlitz and Lewis rivers. This vessel should not be confused with the similar sternwheeler Onward built in 1858 at Canemah, Oregon and dismantled in 1865.

<i>Occident</i> (sternwheeler)

Occident was a steamer that operated on the Willamette River and occasionally its tributary, the Santiam River from 1875 to about 1890. Occident was designed primarily for freight work, and did not have passenger accommodations. This Occident should not be confused with the smaller steam launch Occident, apparently propeller-driven, which operated out of Astoria, Oregon in the 1890s.

<i>Active</i> (sternwheeler) stern-wheel driven steamboat that operated on the upper Willamette River from 1865 to 1872

Active was a stern-wheel driven steamboat that operated on the upper Willamette River from 1865 to 1872. During its short operational life, Active was owned by several different steamboat companies. It was dismantled in 1872 at Canemah, Oregon.

George Anson Pease

George Anson Pease was a well-known steamboat captain in the Pacific Northwest region on the United States, who was active from the earliest days of steamboat navigation on the Willamette River in the 1850s. He worked in various roles until the early 1900s, commanding numerous vessels during that time. During a flood in 1861, while in command of the sternwheeler Onward, Pease rescued 40 people from a flood in the area of Salem, Oregon.

<i>Fannie Patton</i>

Fanny Patton was a stern-wheel driven steamboat that operated on the Willamette River, in Oregon, starting in August 1865. This steamer operated from 1865 to 1880 for various owners, and was a considered a profitable vessel. The steamer was named for the daughter of businessman Edwin N Cook, Frances Mary "Fannie" Cooke (1837–1886), who married Thomas McFadden Patton in 1854. Edwin N. Cook was one of the principals of the People's Transportation Company.

<i>Orient</i> (sternwheeler)

Orient was a light-draft sternwheel-driven steamboat built in 1875 for the Willamette River Transportation Company, a concern owned by pioneer businessman Ben Holladay. Shortly after its completion, it was acquired by the Oregon Steam Navigation Company. Orient was a near-twin vessel of a steamer built at the same time, the Occident.

References

Books

Newspaper collections