Polymer soil stabilization

Last updated
Polymers stabilize soils through interactions with soil particles. Above is a schematic representing different configurations which polymer molecules (such as alkylammonium cations) can adopt when adsorbed between clay layers, in response to the magnitude of charge density on the clay surface. Greater charge densities here result in righter packing and greater clay- clay distances. Polymer-Clay Interactions.png
Polymers stabilize soils through interactions with soil particles. Above is a schematic representing different configurations which polymer molecules (such as alkylammonium cations) can adopt when adsorbed between clay layers, in response to the magnitude of charge density on the clay surface. Greater charge densities here result in righter packing and greater clay- clay distances.

Polymer soil stabilization refers to the addition of polymers to improve the physical properties of soils, most often for geotechnical engineering, construction, or agricultural projects. [1] Even at very small concentrations within soils, various polymers have been shown to increase water retention and reduce erosion, increase soil shear strength, and support soil structure. [2] A wide range of polymers have been used to address problems ranging from the prevention of desertification to the reinforcement of roadbeds. [3] [1] [4]

Contents

Polymers that have been tested for soil stabilization effects include a range of synthetic polymers and biopolymers. [1] [5] Biopolymers in particular offer a more eco-friendly alternative to traditional chemical additives, such as ordinary cement, which may generate a large amount of carbon dioxide during production or cause lasting environmental damage. [1] [6]

Polymers mainly affect the aggregation and strength of soils through their interactions with fine clay particles. Coatings of adsorbed polymers on clays can increase their steric stabilization by preventing clay particles from approaching each other as closely. Alternatively, polymer molecules that bond with multiple clay particles promote flocculation. [2] Hydrogel networks can result in more indirect strengthening within soils by creating a scaffolding for soil particles. Additional strength can be imparted to polymer networks within soils through chemical cross-linking and curing. [1] [5]

Overview

Synthetic polymers began replacing other chemical binders for soil stabilization in agriculture in the late 20th century. [1] Compared to traditional chemical binders, polymer soil additives can achieve the same amount of strengthening at much lower concentrations – for example, mixtures of 0.5-1% of various biopolymers have strength levels that match or exceed those of 10% cement mixtures in soils. [1] Synthetic polymers, including geopolymers, and biopolymers, have been tested for their beneficial interactions with soils. Methods for introducing polymers into soils include mixing, injecting, spraying, and grouting. [1] Liquid polymers, sold as concentrated solutions, can be applied deep within the soil through pressure injection or applied directly to uncompacted soil. [5]

Synthetic polymers

Alumino-silicate based, synthetic geopolymers provide many of the same binding properties as Portland cement. Compared to other polymer additives, many geopolymers are quite durable, with high mechanical strength and thermal stability. They react readily with calcium hydroxide in water, which allows them to act as cementitious binders. Geopolymers offer the advantage of being more environmentally friendly and energy-efficient to produce than traditional chemical additives, and can be synthesized from waste products such as mine tailings or fly ash. [7] When these waste products are treated with an alkaline reagent, the aluminosilicate rapidly depolymerizes and polycondenses into a rigid three dimensional polymeric structure that coats and strengthens soil pores. [8] Geopolymers have been applied to stabilize gypseous soils because of their resistance to sulfur and other chemical attacks, which weaken traditional cement. [9]

The synthesis of chitosan, an example of a biopolymer which has been employed as a soil additive for its stabilizing properties. Chitosan Synthese.svg
The synthesis of chitosan, an example of a biopolymer which has been employed as a soil additive for its stabilizing properties.

Biopolymers

Biopolymers are synthesized as a result of biological processes, and are often less harmful to the landscape and its biota because of their natural origins. Of the three types of biopolymers, polysaccharides have proven more useful as soil binders than polynucleotides or polypeptides. Biopolymers that have been tested for use in soil stabilization include cellulose, starch, chitosan, xanthan, curdlan, and beta-glucan. [1] Some biopolymers are sensitive to water, and wetter soils exhibit weaker biopolymer-clay cohesion. Because of this, when wetted, gel-type biopolymers form hydrogels which have decreased tensile strength but significantly higher compressive strength compared to the original soil. Protein-based biopolymers, though less common, have been used as an alternative to polysaccharides for projects requiring greater water resistance. [1]

Biopolymers may increasingly replace synthetic polymers for soil stabilization projects. They are more environmentally friendly than many other chemical soil additives, and can achieve the same amount of strengthening at much lower concentrations. Increasing use of biopolymers could offset the carbon dioxide emissions associated with cement production, which can be as high as 1.25 tons of carbon dioxide per ton of cement. [1]

Polymer-soil chemistry

Polymer treatments modify the size, shape, and cohesion of soil aggregates by changing the interactions between soil particles. Because polymer-soil interactions occur on the surfaces of soil particles, the amount of surface area in the soil (in other words, its dominant particle size) is of great importance. [5] Polymers have only weak interactions with the large sand- and silt-sized particles of soil, while they bond directly to finer clays. [1] Although polymers mainly interact with the clay fraction of soils, they do change the properties of sandy soils to a lesser degree. [2] Polymer structure dictates how they will interact with clay particles. For example, block copolymers result in very different soil properties than homopolymers, as do ionic and nonionic polymers. Additionally, the mechanisms by which different polymers adsorb onto clay particle surfaces result in different soil properties and responses. [2]

Steric stabilization

Polymers on the surfaces of the colloidal fraction of soils promote steric stabilization of those particles by preventing them from approaching each other and aggregating. This effect is seen in a variety of aqueous and nonaqueous environments, and is not affected by electrolytes in solution. [2] The degree of steric stabilization depends on the amount of clay surface covered by adsorbed polymers, the strength of the polymer bond, the thickness of the polymer layer, and the favorability of the solvent for the polymer loops and tails. Block and graft copolymers, made up of two different homopolymers with differing solubilities in the suspension medium, are most often used for steric stabilization. When synthesized to have alternating regions of hydrophobic and hydrophilic monomers, copolymers can stabilize the suspension because their hydrophobic group adsorbs strongly to the colloid surface while the hydrophilic group is attracted to the solvent. In general, the adsorption of polymers to clay surfaces is entropically favored because one polymer molecule displaces many water molecules which were previously bound to the soil particle. [2]

Polymer and clay particle suspensions have been used to understand the mechanism of this steric stabilization in soils. Consider a homopolymer adsorbed to the surfaces of clay particles in suspension. As the clay particles approach each other to within two times the thickness of the polymer layers, the loops and tails of the polymers on one surface will start to block those on the other surface, leading to a decrease in configurational entropy. This is unfavorable because it increases the Gibbs free energy of the system, and it will be more energetically favorable for the colloid particles to remain farther apart. [2]

The morphology of polymer-clay aggregates is dictated by the entropic and enthalpic contributions to the energy of their interactions. Three possible morphologies depicted above include (1) intercalated, in which polymer molecules alternate with clay layers, (2) flocculated, in which the alternating clay/polymer layers begin to aggregate, and (3) exfoliated, in which a polymer matrix supports individual, separated clay layers. Morphology of polymer-clay aggregates.png
The morphology of polymer-clay aggregates is dictated by the entropic and enthalpic contributions to the energy of their interactions. Three possible morphologies depicted above include (1) intercalated, in which polymer molecules alternate with clay layers, (2) flocculated, in which the alternating clay/polymer layers begin to aggregate, and (3) exfoliated, in which a polymer matrix supports individual, separated clay layers.

Overall, the free energy of steric interactions (ΔGs) can be expressed as a function of both elastic repulsive energy (ΔGel) and the free energy of mixing (ΔGmix):

ΔGs = ΔGel + ΔGmix [2]

The elastic repulsive energy (ΔGel), increases as more polymers adsorb to the surfaces of clay particles. This can be modeled as:

ΔGel = 2kBTΓln(Ω(h)/Ω(∞)) [2]

where kB is the Boltzmann constant, T is the temperature, Γ is the number of adsorbed polymers per unit surface area, and Ω(h) and Ω(∞) are the number of available conformations at h and infinite distances. ΔGs due to steric interactions is also a function of the free energy of mixing (ΔGmix). Most commonly, this will favor greater distances between polymer molecules in solution. [2]

Flocculation

Alternatively, under different conditions, polymers can enhance flocculation. Particle aggregates are held together more strongly by polymers than by electrolytes. Such interactions are called bridging flocculation because a single polymer chain is linked to multiple soil particles. Examples of common bridging polymers include polyacrylamide (PAM) and polyethylene oxide. In one study, PAM was found to increase the size of kaolinite flocs in suspension experiments from 10 μm to several millimeters. [10] The maximum strength benefits of flocculation are achieved when polymers cover a surface area equivalent to half the polymer saturation capacity. [2] Addition of polymer beyond this point causes the polymer to act as a lubricant, allowing the soil particles to slip across each other. [5]

The structure of montmorillonite clay, a 2:1 clay made up of tetrahedral sheets surrounding an octahedral sheet. The clay particles are only weakly bound to each other, so various cations or polymers can be bound within the interlayer space. Montmorillonite-en.svg
The structure of montmorillonite clay, a 2:1 clay made up of tetrahedral sheets surrounding an octahedral sheet. The clay particles are only weakly bound to each other, so various cations or polymers can be bound within the interlayer space.

Biopolymers have been shown to strengthen soils both by cohesion with clay particles to form polymer-clay matrices and by promoting the aggregation of coarser soil particles with each other within the polymer-clay matrix. The hydroxyl groups on polysaccharide biopolymers allow them to form hydrogen bonds directly with charged clay particles (in dry soils), as well as with soil pore water itself (in moist soil). These interactions are promoted by the high surface area of both the biopolymers themselves and the clay particles they bond with. [1] When ionized polymers (such as many biopolymers) with the same charge as clay particles adsorb to their surface, they increase the electrical double layer repulsion. [2]

Cross-linking and curing

The strength of polymer chains can be enhanced by cross-linking, which increases the interactions between chains through bonding with another reactant. [11] The high mechanical strength of soil/polymer mixtures after cross-linking can make many polymers more suited for soil stabilization projects. [1] Curing time after polymer addition can also affect the strength of the polymer-soil structures formed. [12] After seven days of curing, the liquid polymer SS299 resulted in soil with two times the compressive strength of untreated soil. Some polymers can also acquire strength much more rapidly during curing than traditional, non-polymeric chemical additives. [5]

Applications

The structure of polyacrylamide (PAM), a common synthetic polymer flocculating agent used to increase aggregate sizes in clay-rich soils. Polyacrylamide.png
The structure of polyacrylamide (PAM), a common synthetic polymer flocculating agent used to increase aggregate sizes in clay-rich soils.

Soil characteristics that have been altered by addition of polymers include compressive strength, volume stability, hydraulic durability, and conductivity. [5] Polymers can help prevent soil erosion and increase infiltration of water by strengthening soil aggregates and supporting soil structure. The properties of the soil itself are a dominant control on the ability of polymers to interact with it. A study of the cationic, alkaline polymer SS299 (a commercially produced additive) found that the properties of treated soils depend on the plasticity index of the original soil, which reflects its clay content. [5]

Hydrogel swelling of biopolymers reduces the amount of soil pore space, restricting the flow of water and suiting polymer hydrogels for construction projects seeking to minimize water seepage and support vegetation growth. [13] Biopolymers can be added to soils along with synthetic polymers to utilize the properties of both polymers. By increasing the water retention and infiltration rates in soils, the addition of biopolymers increases the availability of water for plants. [1] This is particularly applicable in arid regions like deserts where droughts leave soils susceptible to high rates of erosion during precipitation events. By retaining water, the enhanced soils reduce runoff and its accompanying erosion. [3] PAM has been widely applied as a soil stabilizer for agriculture, both to retain water in fields and to improve run-off water quality by reducing the amount of sediment entering rivers and streams. [14]

See also

Related Research Articles

<span class="mw-page-title-main">Colloid</span> Mixture of an insoluble substance microscopically dispersed throughout another substance

A colloid is a mixture in which one substance consisting of microscopically dispersed insoluble particles is suspended throughout another substance. Some definitions specify that the particles must be dispersed in a liquid, while others extend the definition to include substances like aerosols and gels. The term colloidal suspension refers unambiguously to the overall mixture. A colloid has a dispersed phase and a continuous phase. The dispersed phase particles have a diameter of approximately 1 nanometre to 1 micrometre.

<span class="mw-page-title-main">Plasticizer</span> Substance that is added to a material to make it softer and more flexible

A plasticizer is a substance that is added to a material to make it softer and more flexible, to increase its plasticity, to decrease its viscosity, and/or to decrease friction during its handling in manufacture.

<span class="mw-page-title-main">Dilatant</span> Material in which viscosity increases with the rate of shear strain

A dilatant material is one in which viscosity increases with the rate of shear strain. Such a shear thickening fluid, also known by the initialism STF, is an example of a non-Newtonian fluid. This behaviour is usually not observed in pure materials, but can occur in suspensions.

<span class="mw-page-title-main">Hydrogel</span> Soft water-rich polymer gel

A hydrogel is a biphasic material, a mixture of porous, permeable solids and at least 10% by weight or volume of interstitial fluid composed completely or mainly by water. In hydrogels the porous permeable solid is a water insoluble three dimensional network of natural or synthetic polymers and a fluid, having absorbed a large amount of water or biological fluids. These properties underpin several applications, especially in the biomedical area. Many hydrogels are synthetic, but some are derived from nature. The term 'hydrogel' was coined in 1894.

<span class="mw-page-title-main">Polyelectrolyte</span> Polymers whose repeating units bear an electrolyte group

Polyelectrolytes are polymers whose repeating units bear an electrolyte group. Polycations and polyanions are polyelectrolytes. These groups dissociate in aqueous solutions (water), making the polymers charged. Polyelectrolyte properties are thus similar to both electrolytes (salts) and polymers and are sometimes called polysalts. Like salts, their solutions are electrically conductive. Like polymers, their solutions are often viscous. Charged molecular chains, commonly present in soft matter systems, play a fundamental role in determining structure, stability and the interactions of various molecular assemblies. Theoretical approaches to describing their statistical properties differ profoundly from those of their electrically neutral counterparts, while technological and industrial fields exploit their unique properties. Many biological molecules are polyelectrolytes. For instance, polypeptides, glycosaminoglycans, and DNA are polyelectrolytes. Both natural and synthetic polyelectrolytes are used in a variety of industries.

<span class="mw-page-title-main">Flocculation</span> Process by which colloidal particles come out of suspension to precipitate as floc or flake

Flocculation, in the field of chemistry, is a process by which colloidal particles come out of suspension to sediment under the form of floc or flake, either spontaneously or due to the addition of a clarifying agent. The action differs from precipitation in that, prior to flocculation, colloids are merely suspended, under the form of a stable dispersion and are not truly dissolved in solution.

<span class="mw-page-title-main">Sodium polyacrylate</span> Anionic polyelectrolyte polymer

Sodium polyacrylate (ACR, ASAP, or PAAS), also known as waterlock, is a sodium salt of polyacrylic acid with the chemical formula [−CH2−CH(CO2Na)−]n and has broad applications in consumer products. This super-absorbent polymer (SAP) has the ability to absorb 100 to 1000 times its mass in water. Sodium polyacrylate is an anionic polyelectrolyte with negatively charged carboxylic groups in the main chain. It is a chemical polymer made up of chains of acrylate compounds. It contains sodium, which gives it the ability to absorb large amounts of water. When dissolved in water, it forms a thick and transparent solution due to the ionic interactions of the molecules. Sodium polyacrylate has many favorable mechanical properties. Some of these advantages include good mechanical stability, high heat resistance, and strong hydration. It has been used as an additive for food products including bread, juice, and ice cream.

Superplasticizers (SPs), also known as high range water reducers, are additives used in making high strength concrete. Plasticizers are chemical compounds that enable the production of concrete with approximately 15% less water content. Superplasticizers allow reduction in water content by 30% or more. These additives are employed at the level of a few weight percent. Plasticizers and superplasticizers retard the curing of concrete.

<span class="mw-page-title-main">Particle aggregation</span>

Particle agglomeration refers to formation of assemblages in a suspension and represents a mechanism leading to the functional destabilization of colloidal systems. During this process, particles dispersed in the liquid phase stick to each other, and spontaneously form irregular particle assemblages, flocs, or agglomerates. This phenomenon is also referred to as coagulation or flocculation and such a suspension is also called unstable. Particle agglomeration can be induced by adding salts or other chemicals referred to as coagulant or flocculant.

<span class="mw-page-title-main">Superabsorbent polymer</span> Polymers that can absorb and retain extremely large amounts of a liquid relative to their own mass

A superabsorbent polymer (SAP) (also called slush powder) is a water-absorbing hydrophilic homopolymers or copolymers that can absorb and retain extremely large amounts of a liquid relative to its own mass.

<span class="mw-page-title-main">Emulsion dispersion</span>

An emulsion dispersion is thermoplastics or elastomers suspended in a liquid state by means of emulsifiers.

Paint has four major components: pigments, binders, solvents, and additives. Pigments serve to give paint its color, texture, toughness, as well as determining if a paint is opaque or not. Common white pigments include titanium dioxide and zinc oxide. Binders are the film forming component of a paint as it dries and affects the durability, gloss, and flexibility of the coating. Polyurethanes, polyesters, and acrylics are all examples of common binders. The solvent is the medium in which all other components of the paint are dissolved and evaporates away as the paint dries and cures. The solvent also modifies the curing rate and viscosity of the paint in its liquid state. There are two types of paint: solvent-borne and water-borne paints. Solvent-borne paints use organic solvents as the primary vehicle carrying the solid components in a paint formulation, whereas water-borne paints use water as the continuous medium. The additives that are incorporated into paints are a wide range of things which impart important effects on the properties of the paint and the final coating. Common paint additives are catalysts, thickeners, stabilizers, emulsifiers, texturizers, biocides to fight bacterial growth, etc.

Adsorption is the accumulation and adhesion of molecules, atoms, ions, or larger particles to a surface, but without surface penetration occurring. The adsorption of larger biomolecules such as proteins is of high physiological relevance, and as such they adsorb with different mechanisms than their molecular or atomic analogs. Some of the major driving forces behind protein adsorption include: surface energy, intermolecular forces, hydrophobicity, and ionic or electrostatic interaction. By knowing how these factors affect protein adsorption, they can then be manipulated by machining, alloying, and other engineering techniques to select for the most optimal performance in biomedical or physiological applications.

Adsorption of polyelectrolytes on solid substrates is a surface phenomenon where long-chained polymer molecules with charged groups bind to a surface that is charged in the opposite polarity. On the molecular level, the polymers do not actually bond to the surface, but tend to "stick" to the surface via intermolecular forces and the charges created by the dissociation of various side groups of the polymer. Because the polymer molecules are so long, they have a large amount of surface area with which to contact the surface and thus do not desorb as small molecules are likely to do. This means that adsorbed layers of polyelectrolytes form a very durable coating. Due to this important characteristic of polyelectrolyte layers they are used extensively in industry as flocculants, for solubilization, as supersorbers, antistatic agents, as oil recovery aids, as gelling aids in nutrition, additives in concrete, or for blood compatibility enhancement to name a few.

Protein adsorption refers to the adhesion of proteins to solid surfaces. This phenomenon is an important issue in the food processing industry, particularly in milk processing and wine and beer making. Excessive adsorption, or protein fouling, can lead to health and sanitation issues, as the adsorbed protein is very difficult to clean and can harbor bacteria, as is the case in biofilms. Product quality can be adversely affected if the adsorbed material interferes with processing steps, like pasteurization. However, in some cases protein adsorption is used to improve food quality, as is the case in fining of wines.

Polyelectrolytes are charged polymers capable of stabilizing colloidal emulsions through electrostatic interactions. Their effectiveness can be dependent on molecular weight, pH, solvent polarity, ionic strength, and the hydrophilic-lipophilic balance (HLB). Stabilized emulsions are useful in many industrial processes, including deflocculation, drug delivery, petroleum waste treatment, and food technology.

<span class="mw-page-title-main">Bovine submaxillary mucin coatings</span>

Bovine submaxillary mucin (BSM) coatings are a surface treatment provided to biomaterials intended to reduce the growth of disadvantageous bacteria and fungi such as S. epidermidis, E. coli, and Candida albicans. BSM is a substance extracted from the fresh salivary glands of cows. It exhibits unique physical properties, such as high molecular weight and amphiphilicity, that allow it to be used for many biomedical applications.

Self-healing hydrogels are a specialized type of polymer hydrogel. A hydrogel is a macromolecular polymer gel constructed of a network of crosslinked polymer chains. Hydrogels are synthesized from hydrophilic monomers by either chain or step growth, along with a functional crosslinker to promote network formation. A net-like structure along with void imperfections enhance the hydrogel's ability to absorb large amounts of water via hydrogen bonding. As a result, hydrogels, self-healing alike, develop characteristic firm yet elastic mechanical properties. Self-healing refers to the spontaneous formation of new bonds when old bonds are broken within a material. The structure of the hydrogel along with electrostatic attraction forces drive new bond formation through reconstructive covalent dangling side chain or non-covalent hydrogen bonding. These flesh-like properties have motivated the research and development of self-healing hydrogels in fields such as reconstructive tissue engineering as scaffolding, as well as use in passive and preventive applications.

Soil stabilization is a general term for any physical, chemical, mechanical, biological, or combined method of changing a natural soil to meet an engineering purpose. Improvements include increasing the weight-bearing capabilities, tensile strength, and overall performance of unstable subsoils, sands, and waste materials in order to strengthen road pavements.

<span class="mw-page-title-main">Soil aggregate stability</span>

Soil aggregate stability is a measure of the ability of soil aggregates—soil particles that bind together—to resist breaking apart when exposed to external forces such as water erosion and wind erosion, shrinking and swelling processes, and tillage. Soil aggregate stability is a measure of soil structure and can be affected by soil management.

References

  1. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 Chang, Ilhan; Im, Jooyoung; Cho, Gye-Chun (2016-03-10). "Introduction of Microbial Biopolymers in Soil Treatment for Future Environmentally-Friendly and Sustainable Geotechnical Engineering". Sustainability. 8 (3): 251. doi: 10.3390/su8030251 .
  2. 1 2 3 4 5 6 7 8 9 10 11 12 Luckham, Paul F; Rossi, Sylvia (1999-10-01). "The colloidal and rheological properties of bentonite suspensions". Advances in Colloid and Interface Science. 82 (1–3): 43–92. doi:10.1016/S0001-8686(99)00005-6.
  3. 1 2 Ramadan, Ashraf A.; Lahalih, Shawqui M.; Ali, Sadiqa; Al-Sudairawi, Mane (2010-01-01). Zdruli, Pandi; Pagliai, Marcello; Kapur, Selim; Cano, Angel Faz (eds.). Land Degradation and Desertification: Assessment, Mitigation and Remediation. Springer Netherlands. pp. 307–322. doi:10.1007/978-90-481-8657-0_23. ISBN   9789048186563.
  4. ↑ Zhao, Zhi; Hamdan, Nasser; Shen, Li; Nan, Hanqing; Almajed, Abdullah; Kavazanjian, Edward; He, Ximin (2016-11-15). "Biomimetic Hydrogel Composites for Soil Stabilization and Contaminant Mitigation". Environmental Science & Technology. 50 (22): 12401–12410. Bibcode:2016EnST...5012401Z. doi:10.1021/acs.est.6b01285. ISSN   0013-936X. PMID   27762537.
  5. 1 2 3 4 5 6 7 8 Latifi, Nima; Rashid, Ahmad Safuan A.; Siddiqua, Sumi; Majid, Muhd. Zaimi Abd (2016-09-01). "Strength measurement and textural characteristics of tropical residual soil stabilised with liquid polymer". Measurement. 91: 46–54. Bibcode:2016Meas...91...46L. doi:10.1016/j.measurement.2016.05.029.
  6. ↑ Kögel-Knabner, Ingrid (2002-02-01). "The macromolecular organic composition of plant and microbial residues as inputs to soil organic matter". Soil Biology and Biochemistry. 34 (2): 139–162. doi:10.1016/S0038-0717(01)00158-4.
  7. ↑ Du, Yan-Jun; Yu, Bo-Wei; Liu, Kai; Jiang, Ning-Jun; Liu, Martin D. (2017). "Physical, Hydraulic, and Mechanical Properties of Clayey Soil Stabilized by Lightweight Alkali-Activated Slag Geopolymer". Journal of Materials in Civil Engineering. 29 (2): 04016217. doi:10.1061/(asce)mt.1943-5533.0001743. S2CID   109929046.
  8. ↑ Alhomair, Sultan A.; Gorakhki, Mohammad H.; Bareither, Christopher A. (2017-02-01). "Hydraulic Conductivity of Fly Ash-Amended Mine Tailings". Geotechnical and Geological Engineering. 35 (1): 243–261. doi:10.1007/s10706-016-0101-z. hdl: 10217/176619 . ISSN   0960-3182. S2CID   133394477.
  9. ↑ Alsafi, Shaymaa; Farzadnia, Nima; Asadi, Afshin; Huat, Bujang Kim (2017-04-15). "Collapsibility potential of gypseous soil stabilized with fly ash geopolymer; characterization and assessment". Construction and Building Materials. 137: 390–409. doi:10.1016/j.conbuildmat.2017.01.079.
  10. ↑ Sharma, Sugandha; Lin, Chen-Luh; Miller, Jan D. (2017-02-01). "Multi-scale features including water content of polymer induced kaolinite floc structures". Minerals Engineering. 101: 20–29. doi: 10.1016/j.mineng.2016.11.003 .
  11. ↑ Frankland, S. J. V.; Caglar, A.; Brenner, D. W.; Griebel, M. (2002-03-01). "Molecular Simulation of the Influence of Chemical Cross-Links on the Shear Strength of Carbon Nanotube−Polymer Interfaces". The Journal of Physical Chemistry B. 106 (12): 3046–3048. doi:10.1021/jp015591+. ISSN   1520-6106.
  12. ↑ Gilazghi, Simon T.; Huang, Jie; Rezaeimalek, Sepehr; Bin-Shafique, Sazzad (2016-08-23). "Stabilizing sulfate-rich high plasticity clay with moisture activated polymerization". Engineering Geology. 211: 171–178. doi:10.1016/j.enggeo.2016.07.007.
  13. ↑ Yang, Lixia; Yang, Yang; Chen, Zhang; Guo, Chunxiao; Li, Shaocai (2014-01-01). "Influence of super absorbent polymer on soil water retention, seed germination and plant survivals for rocky slopes eco-engineering". Ecological Engineering. 62: 27–32. doi:10.1016/j.ecoleng.2013.10.019.
  14. ↑ Sojka, R. E.; Bjorneberg, D. L.; Entry, J. A.; Lentz, R. D.; Orts, W. J. (2007). Sparks, Donald L. (ed.). Advances in Agronomy (PDF). Vol. 92. Academic Press. pp. 75–162. doi:10.1016/S0065-2113(04)92002-0. ISBN   9780123736864.
This page is based on this Wikipedia article
Text is available under the CC BY-SA 4.0 license; additional terms may apply.
Images, videos and audio are available under their respective licenses.