StarLAN

Last updated

StarLAN was the first IEEE 802.3 standard for Ethernet over twisted pair wiring. It was standardized by the IEEE Standards Association as 802.3e in 1986, as the 1BASE5 version of Ethernet. The StarLAN Task Force was chaired by Bob Galin.

Contents

Description

An early version of StarLAN was developed by Tim Rock and Bill Aranguren at AT&T Information Systems as an experimental system in 1983. [1] The name StarLAN was coined by the IEEE task force based on the fact that it used a star topology from a central hub in contrast to the bus network of the shared cable 10BASE5 and 10BASE2 networks that had been based on ALOHAnet.

The standard known as 1BASE5 was adopted as 802.3e in 1986 by members of the IEEE 802.3 standards committee as the Twisted Pair Medium Access Control sublayer and Physical Signalling sublayer specification in section 12. [2] The original StarLAN ran at a speed of 1 Mbit/s.

A major design goal in StarLAN was reduction in Ethernet installation costs by the reuse of existing telephone on-premises wiring and compatibility with analog and digital telephone signals in the same cable bundle. The signal modulation and wire pairing used by StarLAN were carefully chosen so that they would not affect or be affected by either the analog signal of a normal call, on hook and off hook transients, or the 20 Hz high-voltage analog ring signal. Reuse of existing wires was critical in many buildings where rewiring was cost prohibitive, where running new wire would disturb asbestos within the building infrastructure, and where the bus topology of coaxial bus Ethernet was not installable.

The wire positioning called T568B in the standard TIA/EIA-568 (later called ANSI/TIA-568) was originally devised for StarLAN, and pair 1 (blue) was left unused to accommodate an analog phone pair. Pairs 2 and 3 (orange and green respectively) carry the StarLAN signals. This greatly simplified the installation of combined voice and data wiring in countries that used registered jack connectors and American wiring practices for their phone service (connecting both to the same cable was a simple matter of using a pin–pin RJ45 splitter or punching down the same wires to two ports). This arrangement prevented harm to private branch exchange (PBX) equipment in the event that a StarLAN cable was plugged into the wrong device.

Since 1BASE5 reused existing wiring, maximum link distance was only approximated at 250 m; depending on cable performance up to 500 m was possible. Up to five chained hubs were allowed. [3]

Parts of the StarLAN technology were patented by AT&T [4] and were initially part of a wider vision from AT&T to link their UNIX-based AT&T 3B2 minicomputers to a network of MS-DOS PCs. [5] A StarLAN card was also offered for the AT&T UNIX PC.

StarLAN 10

In 1988, AT&T released StarLAN 10 operating at 10 Mbit/s. The original StarLAN was renamed StarLAN 1, reflecting its 1 Mbit/s speed. [6]

It was adopted by other networking vendors such as Hewlett-Packard and Ungermann-Bass. Integrated circuits were introduced starting in 1986 that reduced the cost of the interfaces. [7]

StarLAN 10 and SynOptics LattisNet provided the basis for the later 10 megabit per second standard 10BASE-T. The 10BASE-T task force was chaired by Pat Thaler, a member of the StarLAN task force. 10BASE-T used the basic signalling of StarLAN 10 and added link beat. Some network interface cards such as the 3Com 3C-523 could be used with either StarLAN 10 or 10BASE-T, by switching link beat on or off. [8]

Comparison of twisted-pair-based Ethernet physical transport layers (TP-PHYs) [9]
NameStandardStatusSpeed (Mbit/s)Pairs requiredLanes per directionBits per hertz Line code Symbol rate per lane (MBd)BandwidthMax distance (m)CableCable rating (MHz)Usage
StarLAN-1 1BASE5802.3e-1987obsolete1211PE11250voice grade~12 LAN
StarLAN-10802.3e-1988obsolete10211PE1010~100voice grade~12LAN

Related Research Articles

<span class="mw-page-title-main">Ethernet</span> Computer networking technology

Ethernet is a family of wired computer networking technologies commonly used in local area networks (LAN), metropolitan area networks (MAN) and wide area networks (WAN). It was commercially introduced in 1980 and first standardized in 1983 as IEEE 802.3. Ethernet has since been refined to support higher bit rates, a greater number of nodes, and longer link distances, but retains much backward compatibility. Over time, Ethernet has largely replaced competing wired LAN technologies such as Token Ring, FDDI and ARCNET.

<span class="mw-page-title-main">Local area network</span> Computer network that connects devices over a limited area

A local area network (LAN) is a computer network that interconnects computers within a limited area such as a residence, school, laboratory, university campus or office building. By contrast, a wide area network (WAN) not only covers a larger geographic distance, but also generally involves leased telecommunication circuits.

100BaseVG is a 100 Mbit/s Ethernet standard specified to run over four pairs of Category 3 cable. It is also called 100VG-AnyLAN because it was defined to carry both Ethernet and Token Ring frame types.

<span class="mw-page-title-main">10BASE2</span> Once-dominant 10 Mbit/s Ethernet standard

10BASE2 is a variant of Ethernet that uses thin coaxial cable terminated with BNC connectors to build a local area network.

<span class="mw-page-title-main">Ethernet over twisted pair</span> Ethernet physical layers using twisted-pair cables

Ethernet over twisted-pair technologies use twisted-pair cables for the physical layer of an Ethernet computer network. They are a subset of all Ethernet physical layers.

<span class="mw-page-title-main">Category 5 cable</span> Unshielded twisted pair communications cable

Category 5 cable (Cat 5) is a twisted pair cable for computer networks. Since 2001, the variant commonly in use is the Category 5e specification (Cat 5e). The cable standard provides performance of up to 100 MHz and is suitable for most varieties of Ethernet over twisted pair up to 2.5GBASE-T but more commonly runs at 1000BASE-T speeds. Cat 5 is also used to carry other signals such as telephone and video.

<span class="mw-page-title-main">Fast Ethernet</span> Ethernet standards that carry data at the nominal rate of 100 Mbit/s

In computer networking, Fast Ethernet physical layers carry traffic at the nominal rate of 100 Mbit/s. The prior Ethernet speed was 10 Mbit/s. Of the Fast Ethernet physical layers, 100BASE-TX is by far the most common.

<span class="mw-page-title-main">Gigabit Ethernet</span> Standard for Ethernet networking at a data rate of 1 gigabit per second

In computer networking, Gigabit Ethernet is the term applied to transmitting Ethernet frames at a rate of a gigabit per second. The most popular variant, 1000BASE-T, is defined by the IEEE 802.3ab standard. It came into use in 1999, and has replaced Fast Ethernet in wired local networks due to its considerable speed improvement over Fast Ethernet, as well as its use of cables and equipment that are widely available, economical, and similar to previous standards. The first standard for faster 10 Gigabit Ethernet was approved in 2002.

In the seven-layer OSI model of computer networking, the physical layer or layer 1 is the first and lowest layer: the layer most closely associated with the physical connection between devices. The physical layer provides an electrical, mechanical, and procedural interface to the transmission medium. The shapes and properties of the electrical connectors, the frequencies to transmit on, the line code to use and similar low-level parameters, are specified by the physical layer.

Category 3 cable, commonly known as Cat 3 or station wire, and less commonly known as VG or voice-grade, is an unshielded twisted pair (UTP) cable used in telephone wiring. It is part of a family of standards defined jointly by the Electronic Industries Alliance (EIA) and the Telecommunications Industry Association (TIA) and published in TIA/EIA-568-B.

<span class="mw-page-title-main">Power over Ethernet</span> System for delivering power along with data over an Ethernet cable

Power over Ethernet (PoE) describes any of several standards or ad hoc systems that pass electric power along with data on twisted-pair Ethernet cabling. This allows a single cable to provide both a data connection and enough electricity to power networked devices such as wireless access points (WAPs), IP cameras and VoIP phones.

LattisNet was a family of computer networking hardware and software products built and sold by SynOptics Communications during the 1980s. Examples were the 1000, 2500 and 3000 series of LattisHub network hubs. LattisNet was the first implementation of 10 Megabits per second local area networking over unshielded twisted pair wiring in a star topology.

<span class="mw-page-title-main">Ethernet hub</span> Device for interconnecting Ethernet devices

An Ethernet hub, active hub, network hub, repeater hub, multiport repeater, or simply hub is a network hardware device for connecting multiple Ethernet devices together and making them act as a single network segment. It has multiple input/output (I/O) ports, in which a signal introduced at the input of any port appears at the output of every port except the original incoming. A hub works at the physical layer. A repeater hub also participates in collision detection, forwarding a jam signal to all ports if it detects a collision. In addition to standard 8P8C ("RJ45") ports, some hubs may also come with a BNC or an Attachment Unit Interface (AUI) connector to allow connection to legacy 10BASE2 or 10BASE5 network segments.

<span class="mw-page-title-main">Medium-dependent interface</span> Interface between a network device and the data link it communicates over

A medium-dependent interface (MDI) describes the interface in a computer network from a physical-layer implementation to the physical medium used to carry the transmission. Ethernet over twisted pair also defines a medium-dependent interface – crossover (MDI-X) interface. Auto–MDI-X ports on newer network interfaces detect if the connection would require a crossover and automatically choose the MDI or MDI-X configuration to complement the other end of the link.

An Ethernet crossover cable is a crossover cable for Ethernet used to connect computing devices together directly. It is most often used to connect two devices of the same type, e.g. two computers or two switches to each other. By contrast, straight through patch cables are used to connect devices of different types, such as a computer to a network switch.

<span class="mw-page-title-main">Ethernet physical layer</span> Electrical or optical properties between network devices

The physical-layer specifications of the Ethernet family of computer network standards are published by the Institute of Electrical and Electronics Engineers (IEEE), which defines the electrical or optical properties and the transfer speed of the physical connection between a device and the network or between network devices. It is complemented by the MAC layer and the logical link layer. An implementation of a specific physical layer is commonly referred to as PHY.

Ethernet in the first mile (EFM) refers to using one of the Ethernet family of computer network technologies between a telecommunications company and a customer's premises. From the customer's point of view, it is their first mile, although from the access network's point of view it is known as the last mile.

ANSI/TIA-568 is a technical standard for commercial building cabling for telecommunications products and services. The title of the standard is Commercial Building Telecommunications Cabling Standard and is published by the Telecommunications Industry Association (TIA), a body accredited by the American National Standards Institute (ANSI).

IEEE 802.3bz, NBASE-T and MGBASE-T are standards released in 2016 for Ethernet over twisted pair at speeds of 2.5 and 5 Gbit/s. These use the same cabling as the ubiquitous Gigabit Ethernet, yet offer higher speeds. The resulting standards are named 2.5GBASE-T and 5GBASE-T.

Classic Ethernet is a family of 10 Mbit/s Ethernet standards, which is the first generation of Ethernet standards. In 10BASE-X, the 10 represents its maximum throughput of 10 Mbit/s, BASE indicates its use of baseband transmission, and X indicates the type of medium used. Classic Ethernet includes coax, twisted pair and optical variants. The first Ethernet standard was published in 1983 and classic Ethernet operating at 10 Mbit/s was the dominant form of Ethernet until the first standard for Fast Ethernet was approved in 1995.

References

  1. ↑ Urs von Burg (2001). The triumph of Ethernet: technological communities and the battle for the LAN standard. Stanford University Press. pp. 175–176, 255–256. ISBN   978-0-8047-4095-1.
  2. ↑ 802.3a,b,c, and e-1988 IEEE Standards for Local Area Networks: Supplements to Carrier Sense Multiple Access With Collision Detection (CSMA/CD) Access Method and Physical Layer Specifications. IEEE Standards Association. 1987. doi:10.1109/IEEESTD.1987.78883. ISBN   978-0-471-61153-0.
  3. ↑ IEEE 802.3 Clause 12.1.4
  4. ↑ US 4674085 Patent "Local area network" William L. Aranguren, Mario A. Restrepo, and Michael J. Sidney, Filed October 6, 1986, issued June 16, 1987.
  5. ↑ "Although expensive and slow, the system allows minis and PCs to share data" , 27 Oct 1987, p229, PC Mag
  6. ↑ StarLAN Technology Report, 4th Edition. Architecture Technology Corporation. 1991. ISBN   9781483285054.
  7. ↑ Mary Petrosky (June 9, 1986). "Starlan nets: Chip set chips away at Interface cost". Network World. Vol. 3, no. 14. p. 4. Retrieved June 10, 2011.
  8. ↑ Ohland, Louis. "3Com 3C523". Walsh Computer Technology. Retrieved 1 April 2015.
  9. ↑ Charles E. Spurgeon (2014). Ethernet: The Definitive Guide (2nd ed.). O'Reilly Media. ISBN   978-1-4493-6184-6.
This page is based on this Wikipedia article
Text is available under the CC BY-SA 4.0 license; additional terms may apply.
Images, videos and audio are available under their respective licenses.