Tuning fork

Last updated

Tuning fork by John Walker stamped with note (E) and frequency in hertz (659) TuningFork659Hz.jpg
Tuning fork by John Walker stamped with note (E) and frequency in hertz (659)

A tuning fork is an acoustic resonator in the form of a two-pronged fork with the prongs (tines) formed from a U-shaped bar of elastic metal (usually steel). It resonates at a specific constant pitch when set vibrating by striking it against a surface or with an object, and emits a pure musical tone once the high overtones fade out. A tuning fork's pitch depends on the length and mass of the two prongs. They are traditional sources of standard pitch for tuning musical instruments.

Contents

The tuning fork was invented in 1711 by British musician John Shore, sergeant trumpeter and lutenist to the royal court. [1]

Description

Motion of an A-440 tuning fork (greatly exaggerated) vibrating in its principal mode Mode Shape of a Tuning Fork at Eigenfrequency 440.09 Hz.gif
Motion of an A-440 tuning fork (greatly exaggerated) vibrating in its principal mode

A tuning fork is a fork-shaped acoustic resonator used in many applications to produce a fixed tone. The main reason for using the fork shape is that, unlike many other types of resonators, it produces a very pure tone, with most of the vibrational energy at the fundamental frequency. The reason for this is that the frequency of the first overtone is about ⁠52/22⁠ = ⁠25/4⁠ = 6+1⁄4 times the fundamental (about 2+1⁄2 octaves above it). [2] By comparison, the first overtone of a vibrating string or metal bar is one octave above (twice) the fundamental, so when the string is plucked or the bar is struck, its vibrations tend to mix the fundamental and overtone frequencies. When the tuning fork is struck, little of the energy goes into the overtone modes; they also die out correspondingly faster, leaving a pure sine wave at the fundamental frequency. It is easier to tune other instruments with this pure tone.

Another reason for using the fork shape is that it can then be held at the base without damping the oscillation. That is because its principal mode of vibration is symmetric, with the two prongs always moving in opposite directions, so that at the base where the two prongs meet there is a node (point of no vibratory motion) which can therefore be handled without removing energy from the oscillation (damping). However, there is still a tiny motion induced in the handle in its longitudinal direction (thus at right angles to the oscillation of the prongs) which can be made audible using any sort of sound board. Thus by pressing the tuning fork's base against a sound board such as a wooden box, table top, or bridge of a musical instrument, this small motion, but which is at a high acoustic pressure (thus a very high acoustic impedance), is partly converted into audible sound in air which involves a much greater motion (particle velocity) at a relatively low pressure (thus low acoustic impedance). [3] The pitch of a tuning fork can also be heard directly through bone conduction, by pressing the tuning fork against the bone just behind the ear, or even by holding the stem of the fork in one's teeth, conveniently leaving both hands free. [4] Bone conduction using a tuning fork is specifically used in the Weber and Rinne tests for hearing in order to bypass the middle ear. If just held in open air, the sound of a tuning fork is very faint due to the acoustic impedance mismatch between the steel and air. Moreover, since the feeble sound waves emanating from each prong are 180° out of phase, those two opposite waves interfere, largely cancelling each other. Thus when a solid sheet is slid in between the prongs of a vibrating fork, the apparent volume actually increases, as this cancellation is reduced, just as a loudspeaker requires a baffle in order to radiate efficiently.

Commercial tuning forks are tuned to the correct pitch at the factory, and the pitch and frequency in hertz is stamped on them. They can be retuned by filing material off the prongs. Filing the ends of the prongs raises the pitch, while filing the inside of the base of the prongs lowers it.

Currently, the most common tuning fork sounds the note of A = 440 Hz, the standard concert pitch that many orchestras use. That A is the pitch of the violin's second-highest string, the highest string of the viola, and an octave above the highest string of the cello. Orchestras between 1750 and 1820 mostly used A = 423.5 Hz, though there were many forks and many slightly different pitches. [5] Standard tuning forks are available that vibrate at all the pitches within the central octave of the piano, and also other pitches.

Tuning fork pitch varies slightly with temperature, due mainly to a slight decrease in the modulus of elasticity of steel with increasing temperature. A change in frequency of 48 parts per million per °F (86 ppm per °C) is typical for a steel tuning fork. The frequency decreases (becomes flat) with increasing temperature. [6] Tuning forks are manufactured to have their correct pitch at a standard temperature. The standard temperature is now 20 °C (68 °F), but 15 °C (59 °F) is an older standard. The pitch of other instruments is also subject to variation with temperature change.

Calculation of frequency

The frequency of a tuning fork depends on its dimensions and what it is made from: [7]

where

f is the frequency the fork vibrates at, (SI units: 1/s)
N ≈ 3.516015 is the square of the smallest positive solution to cos(x)cosh(x) = −1, [8] which arises from the boundary conditions of the prong’s cantilevered structure.
L is the length of the prongs, (m)
E is the Young's modulus (elastic modulus or stiffness) of the material the fork is made from, (Pa or N/m2 or kg/(ms2))
I is the second moment of area of the cross-section, (m4)
ρ is the density of the fork's material (kg/m3), and
A is the cross-sectional area of the prongs (tines) (m2).

The ratio I/A in the equation above can be rewritten as r2/4 if the prongs are cylindrical with radius r, and a2/12 if the prongs have rectangular cross-section of width a along the direction of motion.

Uses

Tuning forks have traditionally been used to tune musical instruments, though electronic tuners have largely replaced them. Forks can be driven electrically by placing electronic oscillator-driven electromagnets close to the prongs.

In musical instruments

A number of keyboard musical instruments use principles similar to tuning forks. The most popular of these is the Rhodes piano, in which hammers hit metal tines that vibrate in the magnetic field of a pickup, creating a signal that drives electric amplification. The earlier, un-amplified dulcitone, which used tuning forks directly, suffered from low volume.

In clocks and watches

Quartz crystal resonator from a modern quartz watch, formed in the shape of a tuning fork. It vibrates at 32,768 Hz, in the ultrasonic range. Inside QuartzCrystal-Tuningfork.jpg
Quartz crystal resonator from a modern quartz watch, formed in the shape of a tuning fork. It vibrates at 32,768 Hz, in the ultrasonic range.
A Bulova Accutron watch from the 1960s, which uses a steel tuning fork (visible in center) vibrating at 360 Hz. Accutron.jpg
A Bulova Accutron watch from the 1960s, which uses a steel tuning fork (visible in center) vibrating at 360 Hz.

The quartz crystal that serves as the timekeeping element in modern quartz clocks and watches is in the form of a tiny tuning fork. It usually vibrates at a frequency of 32,768 Hz in the ultrasonic range (above the range of human hearing). It is made to vibrate by small oscillating voltages applied by an electronic oscillator circuit to metal electrodes plated on the surface of the crystal. Quartz is piezoelectric, so the voltage causes the tines to bend rapidly back and forth.

The Accutron, an electromechanical watch developed by Max Hetzel [9] and manufactured by Bulova beginning in 1960, used a 360-hertz steel tuning fork as its timekeeper, powered by electromagnets attached to a battery-powered transistor oscillator circuit. The fork provided greater accuracy than conventional balance wheel watches. The humming sound of the tuning fork was audible when the watch was held to the ear.

Medical and scientific uses

1 kHz tuning fork vacuum tube oscillator used by the U.S. National Bureau of Standards (now NIST) in 1927 as a frequency standard. Tuning fork oscillator frequency standard.jpg
1 kHz tuning fork vacuum tube oscillator used by the U.S. National Bureau of Standards (now NIST) in 1927 as a frequency standard.

Alternatives to the common A=440 standard include philosophical or scientific pitch with standard pitch of C=512. According to Rayleigh, physicists and acoustic instrument makers used this pitch. [10] The tuning fork John Shore gave to George Frideric Handel produces C=512. [11]

Tuning forks, usually C512, are used by medical practitioners to assess a patient's hearing. This is most commonly done with two exams called the Weber test and Rinne test, respectively. Lower-pitched ones, usually at C128, are also used to check vibration sense as part of the examination of the peripheral nervous system. [12]

Orthopedic surgeons have explored using a tuning fork (lowest frequency C=128) to assess injuries where bone fracture is suspected. They hold the end of the vibrating fork on the skin above the suspected fracture, progressively closer to the suspected fracture. If there is a fracture, the periosteum of the bone vibrates and fires nociceptors (pain receptors), causing a local sharp pain.[ citation needed ] This can indicate a fracture, which the practitioner refers for medical X-ray. The sharp pain of a local sprain can give a false positive.[ citation needed ] Established practice, however, requires an X-ray regardless, because it's better than missing a real fracture while wondering if a response means a sprain. A systematic review published in 2014 in BMJ Open suggests that this technique is not reliable or accurate enough for clinical use. [13]

Non-medical and non-scientific uses

Tuning forks also play a role in several alternative therapy practices, such as sonopuncture and polarity therapy. [14]

Radar gun calibration

A radar gun that measures the speed of cars or a ball in sports is usually calibrated with a tuning fork. [15] [16] Instead of the frequency, these forks are labeled with the calibration speed and radar band (e.g., X-band or K-band) they are calibrated for.

In gyroscopes

Doubled and H-type tuning forks are used for tactical-grade Vibrating Structure Gyroscopes and various types of microelectromechanical systems. [17]

Level sensors

Tuning fork forms the sensing part of vibrating point level sensors. The tuning fork is kept vibrating at its resonant frequency by a piezoelectric device. Upon coming in contact with solids, amplitude of oscillation goes down, the same is used as a switching parameter for detecting point level for solids. [18] For liquids, the resonant frequency of tuning fork changes upon coming in contact with the liquids, change in frequency is used to detect level.

See also

Related Research Articles

<span class="mw-page-title-main">Harmonic series (music)</span> Sequence of frequencies

The harmonic series is the sequence of harmonics, musical tones, or pure tones whose frequency is an integer multiple of a fundamental frequency.

<span class="mw-page-title-main">Musical tuning</span> Terms for tuning an instrument and a systems of pitches

In music, there are two common meanings for tuning:

<span class="mw-page-title-main">Harmonic</span> Wave with frequency an integer multiple of the fundamental frequency

In physics, acoustics, and telecommunications, a harmonic is a sinusoidal wave with a frequency that is a positive integer multiple of the fundamental frequency of a periodic signal. The fundamental frequency is also called the 1st harmonic; the other harmonics are known as higher harmonics. As all harmonics are periodic at the fundamental frequency, the sum of harmonics is also periodic at that frequency. The set of harmonics forms a harmonic series.

<span class="mw-page-title-main">Overtone</span> Tone with a frequency higher than the frequency of the reference tone

An overtone is any resonant frequency above the fundamental frequency of a sound. In other words, overtones are all pitches higher than the lowest pitch within an individual sound; the fundamental is the lowest pitch. While the fundamental is usually heard most prominently, overtones are actually present in any pitch except a true sine wave. The relative volume or amplitude of various overtone partials is one of the key identifying features of timbre, or the individual characteristic of a sound.

<span class="mw-page-title-main">String instrument</span> Class of musical instruments with vibrating strings

In musical instrument classification, string instruments, or chordophones, are musical instruments that produce sound from vibrating strings when a performer strums, plucks, strikes or sounds the strings in varying manners.

<span class="mw-page-title-main">Pitch (music)</span> Perceptual property in music ordering sounds from low to high

Pitch is a perceptual property that allows sounds to be ordered on a frequency-related scale, or more commonly, pitch is the quality that makes it possible to judge sounds as "higher" and "lower" in the sense associated with musical melodies. Pitch is a major auditory attribute of musical tones, along with duration, loudness, and timbre.

Piano acoustics is the set of physical properties of the piano that affect its sound. It is an area of study within musical acoustics.

Overblowing is the manipulation of supplied air through a wind instrument that causes the sounded pitch to jump to a higher one without a fingering change or the operation of a slide. Overblowing may involve a change in the air pressure, in the point at which the air is directed, or in the resonance characteristics of the chamber formed by the mouth and throat of the player.

<span class="mw-page-title-main">Resonator</span> Device or system that exhibits resonance

A resonator is a device or system that exhibits resonance or resonant behavior. That is, it naturally oscillates with greater amplitude at some frequencies, called resonant frequencies, than at other frequencies. The oscillations in a resonator can be either electromagnetic or mechanical. Resonators are used to either generate waves of specific frequencies or to select specific frequencies from a signal. Musical instruments use acoustic resonators that produce sound waves of specific tones. Another example is quartz crystals used in electronic devices such as radio transmitters and quartz watches to produce oscillations of very precise frequency.

<span class="mw-page-title-main">Piano tuning</span> Profession

Piano tuning is the process of adjusting the tension of the strings of an acoustic piano so that the musical intervals between strings are in tune. The meaning of the term 'in tune', in the context of piano tuning, is not simply a particular fixed set of pitches. Fine piano tuning requires an assessment of the vibration interaction among notes, which is different for every piano, thus in practice requiring slightly different pitches from any theoretical standard. Pianos are usually tuned to a modified version of the system called equal temperament.

Musical acoustics or music acoustics is a multidisciplinary field that combines knowledge from physics, psychophysics, organology, physiology, music theory, ethnomusicology, signal processing and instrument building, among other disciplines. As a branch of acoustics, it is concerned with researching and describing the physics of music – how sounds are employed to make music. Examples of areas of study are the function of musical instruments, the human voice, computer analysis of melody, and in the clinical use of music in music therapy.

<span class="mw-page-title-main">Flue pipe</span>

A flue pipe is an organ pipe that produces sound through the vibration of air molecules, in the same manner as a recorder or a whistle, in a pipe organ. Air under pressure is driven through a flue and against a sharp lip called a labium, causing the column of air in the pipe to resonate at a frequency determined by the pipe length. Thus, there are no moving parts in a flue pipe. This is in contrast to reed pipes, whose sound is driven by beating reeds, as in a clarinet.

Stretched tuning is a detail of musical tuning, applied to wire-stringed musical instruments, older, non-digital electric pianos, and some sample-based synthesizers based on these instruments, to accommodate the natural inharmonicity of their vibrating elements. In stretched tuning, two notes an octave apart, whose fundamental frequencies theoretically have an exact 2:1 ratio, are tuned slightly farther apart. "For a stretched tuning the octave is greater than a factor of 2; for a compressed tuning the octave is smaller than a factor of 2."

<span class="mw-page-title-main">Acoustic resonance</span> Resonance phenomena in sound and musical devices

Acoustic resonance is a phenomenon in which an acoustic system amplifies sound waves whose frequency matches one of its own natural frequencies of vibration.

An acoustic guitar is a musical instrument in the string family. When a string is plucked, its vibration is transmitted from the bridge, resonating throughout the top of the guitar. It is also transmitted to the side and back of the instrument, resonating through the air in the body, and producing sound from the sound hole. While the original, general term for this stringed instrument is guitar, the retronym 'acoustic guitar' – often used to indicate the steel stringed model – distinguishes it from an electric guitar, which relies on electronic amplification. Typically, a guitar's body is a sound box, of which the top side serves as a sound board that enhances the vibration sounds of the strings. In standard tuning the guitar's six strings are tuned (low to high) E2 A2 D3 G3 B3 E4.

In music, the undertone series or subharmonic series is a sequence of notes that results from inverting the intervals of the overtone series. While overtones naturally occur with the physical production of music on instruments, undertones must be produced in unusual ways. While the overtone series is based upon arithmetic multiplication of frequencies, resulting in a harmonic series, the undertone series is based on arithmetic division.

<span class="mw-page-title-main">Eight-foot pitch</span> Standard pitch designation

An organ pipe, or a harpsichord string, designated as eight-foot pitch (8′) is sounded at standard, ordinary pitch. For example, the A above middle C in eight-foot pitch would be sounded at 440 Hz.

<span class="mw-page-title-main">Violin acoustics</span> Area of study within musical acoustics

Violin acoustics is an area of study within musical acoustics concerned with how the sound of a violin is created as the result of interactions between its many parts. These acoustic qualities are similar to those of other members of the violin family, such as the viola.

Sympathetic resonance or sympathetic vibration is a harmonic phenomenon wherein a passive string or vibratory body responds to external vibrations to which it has a harmonic likeness. The classic example is demonstrated with two similarly-tuned tuning forks. When one fork is struck and held near the other, vibrations are induced in the unstruck fork, even though there is no physical contact between them. In similar fashion, strings will respond to the vibrations of a tuning fork when sufficient harmonic relations exist between them. The effect is most noticeable when the two bodies are tuned in unison or an octave apart, as there is the greatest similarity in vibrational frequency. Sympathetic resonance is an example of injection locking occurring between coupled oscillators, in this case coupled through vibrating air. In musical instruments, sympathetic resonance can produce both desirable and undesirable effects.

Vocal resonance may be defined as "the process by which the basic product of phonation is enhanced in timbre and/or intensity by the air-filled cavities through which it passes on its way to the outside air." Throughout the vocal literature, various terms related to resonation are used, including: amplification, filtering, enrichment, enlargement, improvement, intensification, and prolongation. Acoustic authorities would question many of these terms from a strictly scientific perspective. However, the main point to be drawn from these terms by a singer or speaker is that the result of resonation is to make a better sound, or at least suitable to a certain esthetical and practical domain.

References

  1. ↑ Feldmann, H. (1997). "History of the tuning fork. I: Invention of the tuning fork, its course in music and natural sciences. Pictures from the history of otorhinolaryngology, presented by instruments from the collection of the Ingolstadt German Medical History Museum". Laryngo-rhino-otologie. 76 (2): 116–22. doi:10.1055/s-2007-997398. PMID   9172630.
  2. ↑ Tyndall, John (1915). Sound. New York: D. Appleton & Co. p. 156.
  3. ↑ Rossing, Thomas D.; Moore, F. Richard; Wheeler, Paul A. (2001). The Science of Sound (3rd ed.). Pearson. ISBN   978-0805385656.[ page needed ]
  4. ↑ Dan Fox (1996). Teach Yourself to Play Mandolin. Alfred Music Publishing. ISBN   9780739002865 . Retrieved 3 July 2015.
  5. ↑ Fletcher, Neville H.; Rossing, Thomas (2008). The Physics of Musical Instruments (2nd ed.). Springer. ISBN   978-0387983745.[ page needed ]
  6. ↑ Ellis, Alexander J. (1880). "On the History of Musical Pitch". Journal of the Society of Arts. 28 (545): 293–336. Bibcode:1880Natur..21..550E. doi: 10.1038/021550a0 .
  7. ↑ Han, Seon M.; Benaroya, Haym; Wei, Timothy (1999). "Dynamics of Transversely Vibrating Beams Using Four Engineering Theories". Journal of Sound and Vibration. 225 (5): 935–988. Bibcode:1999JSV...225..935H. doi:10.1006/jsvi.1999.2257. S2CID   121014931.
  8. ↑ Whitney, Scott (23 April 1999). "Vibrations of Cantilever Beams: Deflection, Frequency, and Research Uses". University of Nebraska–Lincoln. Retrieved 9 November 2011.
  9. ↑ ch 312290
  10. ↑ Rayleigh, J. W. S. (1945). The Theory of Sound . New York: Dover. p.  9. ISBN   0-486-60292-3.
  11. ↑ Bickerton, RC; Barr, GS (December 1987). "The origin of the tuning fork". Journal of the Royal Society of Medicine . 80 (12): 771–773. doi:10.1177/014107688708001215. PMC   1291142 . PMID   3323515.
  12. ↑ Bickley, Lynn; Szilagyi, Peter (2009). Bates' guide to the physical examination and history taking (10th ed.). Philadelphia, PA: Lippincott Williams & Wilkins. ISBN   978-0-7817-8058-2.
  13. ↑ Mugunthan, Kayalvili; Doust, Jenny; Kurz, Bodo; Glasziou, Paul (4 August 2014). "Is there sufficient evidence for tuning fork tests in diagnosing fractures? A systematic review". BMJ Open . 4 (8): e005238. doi:10.1136/bmjopen-2014-005238. PMC   4127942 . PMID   25091014. Open Access logo PLoS transparent.svg
  14. ↑ Hawkins, Heidi (August 1995). "SONOPUNCTURE: Acupuncture Without Needles". Holistic Health News.
  15. ↑ "Calibration of Police Radar Instruments" (PDF). National Bureau of Standards. 1976. Archived from the original (PDF) on 22 February 2012. Retrieved 29 October 2008.
  16. ↑ "A detailed explanation of how police radars work". Radars.com.au. Perth, Australia: TCG Industrial. 2009. Retrieved 8 April 2010.
  17. ↑ Proceedings of Anniversary Workshop on Solid-State Gyroscopy (19–21 May 2008. Yalta, Ukraine). Kyiv/Kharkiv: ATS of Ukraine. 2009. ISBN   978-976-0-25248-5.
  18. ↑ "Vital- Vibrating Fork Level Switch for Solids". Sapcon Instruments. Retrieved 28 May 2023.
This page is based on this Wikipedia article
Text is available under the CC BY-SA 4.0 license; additional terms may apply.
Images, videos and audio are available under their respective licenses.