Bogie exchange

Last updated
A drawing of the Ramsey car-transfer apparatus from the patent application Ramsey transfer.jpg
A drawing of the Ramsey car-transfer apparatus from the patent application

Bogie exchange is a system for operating railway wagons on two or more gauges to overcome difference in the track gauge. To perform a bogie exchange, a car is converted from one gauge to another by removing the bogies or trucks (the chassis containing the wheels and axles of the car), and installing a new bogie with differently spaced wheels. It is generally limited to wagons and carriages, though the bogies on diesel locomotives can be exchanged if enough time is available.

Contents

Bogies exchange operation in Ussuriisk (near Vladivostok) at the Chinese-Russian border Bogies-exchange.jpg
Bogies exchange operation in Ussuriisk (near Vladivostok) at the ChineseRussian border
Bogie change station at Chop railway station in Ukraine, which connects to Hungary and Slovakia Bogie change station at Chop station Ukraine.jpg
Bogie change station at Chop railway station in Ukraine, which connects to Hungary and Slovakia

The term can also refer to the rebuilding of rolling-stock for permanent use on another gauge, e.g. the Little Joe electric locomotives intended for the Soviet Union (Russian gauge) which were rebuilt for use in the United States, or the New Zealand British Rail Mark 2 carriage rebuilt for use on the NZR Cape gauge

Wagons and carriages

Bogie wagons can have their gauge changed by lifting them off one set of bogies and putting them back down again on another set of bogies. The pin that centres the bogies and the hoses and fittings for the brakes must be compatible. A generous supply of bogies of each gauge is needed to accommodate the ebb and flow of traffic. The bogies and wagons also need to have standardized hooks, etc., where they may be efficiently lifted. The two wheel sets on four-wheel wagons can be changed as well if the wagon has been designed accordingly.

Engines

Steam

Steam locomotives can be designed for more than one gauge, by having, for example, reversible wheel hubs that suit two alternative gauges. This was done in the 1930s and beyond in Victoria for possible gauge conversion, though no engines were ever converted in this manner other than one heritage engine (R766). Some 1,000 mm (3 ft 3+38 in) metre gauge Garratt locomotives of East Africa were designed for easy conversion to 3 ft 6 in (1,067 mm) gauge, though again none ever was.

In 1944, the LMS re-gauged a pair of "Jinty" 0-6-0 tank locomotives – originally built to UK 4 ft 8+12 in (1,435 mm) standard gauge – for use on its 5 ft 3 in (1,600 mm) gauge Northern Counties Committee (NCC) lines in Northern Ireland; re-designated as Class Y, they largely undertook shunting work on dockyard lines in Belfast. The re-gauging was performed by simply reversing the wheel centres so that the spokes dished outwards.

In the southern United States, some steam locomotives built by Baldwin were designed for easy conversion from 5 ft (1,524 mm) to 4 ft 8+12 in (1,435 mm) standard gauge .

Diesel

Diesel locomotives have bogies like wagons and carriages, only with more cables for the traction motors and take a little longer to convert. In Australia, some classes of diesel locomotives are regularly gauge-converted[ citation needed ] to suit traffic requirements on the 1,435 mm (4 ft 8+12 in), 1,600 mm (5 ft 3 in), and 1,067 mm (3 ft 6 in) networks.

Since the 1,067 mm (3 ft 6 in) networks in Australia are not all connected to each other, being separated by deserts or lines of other gauges, they are bogie-exchanged or piggybacked on road or rail vehicles when transferred between these networks.

Electric

The Little Joe electric locomotives intended for the Soviet Union were rebuilt for use in the United States.

Raising or lowering

Raise

The simplest way to carry out bogie exchange is to lift the wagons off the bogies and replace them back on new bogies. This may require the wagons in a train to be uncoupled, and continuous brakes disconnected. If the wagons are swung out of the way by an overhead hoist, they may sway, which wastes time settling them down.

The Nutter hoist, patented in 1871, used screw jacks to lift cars off of their bogies. [1] The Imboden railway-car lifter, from 1875, used a steam cylinder to wedge the car into the air. [2]

Lower

Another way of carrying out bogie exchange is to lower the bogies onto a trolley in a pit, after which the trolleys are rolled out of the way and others return. This may allow the train couplings and continuous brakes to remain connected. In addition, the bogies never need leave a solid surface, so they can be wheeled in and out more quickly. This method was used at Dry Creek railway station, Adelaide. [3]

Charles Tisdale patented a system of ramps and moving supports for lowering the trucks out from under a railroad car in 1873. [4] George Atkinson patented a hoist and transfer table arrangement in 1882; this dropped the bogies from under a car and shift them to the side. [5] Ramsay's apparatus patented in 1884 used hydraulic jacks to support the car while lowering the track with the bogies out from under it. [6]

Countries

Australia

Between 1961 and 1995, Australia had five bogie exchange centres, which opened and closed as gauge conversion work proceeded. The gauges served were 1,435 mm (4 ft 8+12 in) and 1,600 mm (5 ft 3 in), though the 1,067 mm (3 ft 6 in) Queensland did acquire 100 bogie-exchange compatible QLX wagons just in case. All the wagons involved had wagon codes ending in "X", such as VLX.

The centres were:

The busiest facility was that at Dynon, in a typical year (1981–82), 24,110 wagons were bogie exchanged, an average of 66 per day. This was done by one shift of 18 men, compared with the 100 men required if the same amount of freight were transferred wagon to wagon. [11]

Belarus

Bogie exchange in Brest Gauge changing in Brest, Belarus 08.jpg
Bogie exchange in Brest

Bolivia

Bogie exchange was used between 2 ft 6 in (762 mm) and 1,000 mm (3 ft 3+38 in) gauge on the Ferrocarril de Antofagasta a Bolivia Railway.

Canada

China

A bogie exchange station exists at the Chinese border to Mongolia. Both the Moscow-Beijing passenger train (Trans-Siberian) and freight trains get their bogies exchanged. Mongolia has 1,520 mm (4 ft 11+2732 in), China has 1,435 mm (4 ft 8+12 in) standard gauge . Also, a bogie exchange station was placed farther east at the Russian–Chinese border crossing at Zabaykalsk/Manzhouli. Also, China and ex-soviet countries use the different type coupler (Janney and SA-3). An adapter may be used. [12]

Finland

A bogie exchange station exists in the Port of Turku with a short stretch of 1,435 mm (4 ft 8+12 in) gauge railway. Freight cars get their bogies exchanged. SeaRail train ferries go from Germany and Sweden. They carry no passenger trains, and passengers must walk to Turku Harbour railway station opposite the ferry terminals. Finland has 1,524 mm (5 ft) broad gauge.

Germany

In 1898 Emil Breidsprecher, a director of the MarienburgMława railway and a future professor at the Königliche Technische Hochschule zu Danzig, [13] invented a system that allowed to change wheelsets in wagons that travelled across a break of gauge, without the need to unload them first. In September 1901 a facility was installed at the then German-Russian border at Iłowo. [14] The system was used until 1914 on some railway border crossings between Russia and states using standard gauge; [15] known locations, in addition to Iłowo, are Łódź (then an industrial centre served by both standard and broad gauge railway lines) and Novoselytsia (then Austrian-Russian border), there were also some small installations to meet local demand. As of 1938, the sole facility operated at Zdolbuniv at the then Polish-Soviet border. [16]

A bogie exchange station in the port of Mukran serves train ferries that go to and from Russia, Latvia, and Lithuania, which have 1,520 mm (4 ft 11+2732 in) broad gauge.

Iran

Kazakhstan

Moldova

North Korea

The bogies of the direct sleeping car Moscow – Pyongyang, which runs twice monthly, are exchanged there. [17]

Peru

Romania

Russia

Spain

A Paris-Algeciras through coach (at right) being shunted for bogie exchange at Irun railway station, Spain, 1993 05 052a Bf Irun, RENFE-Bmp, SNCF-Bc.jpg
A Paris–Algeciras through coach (at right) being shunted for bogie exchange at Irun railway station, Spain, 1993

Tunisia

Ukraine

United States

A Burlington and Western train in 1898. Two standard-gauge cars riding on narrow-gauge trucks head the train. Burlington and Western crossing Dry Branch Creek.jpg
A Burlington and Western train in 1898. Two standard-gauge cars riding on narrow-gauge trucks head the train.

Transfer time

Bogie exchange conversion times were:

Variable gauge axles

Variable-gauge axles in an automatic track gauge changeover system (ATGCS) is a newer development and is faster than bogie exchange. The SUW 2000 ATGCS requires a changeover track about 20 metres (66 ft) long, with a shed if snow is around compared to a small marshalling yard required by bogie exchange.

Axle exchange

An alternative to variable gauge axles and bogie exchange is wheelset exchange.

See also

Related Research Articles

<span class="mw-page-title-main">Transport in Russia</span>

The transport network of the Russian Federation is one of the world's most extensive transport networks. The national web of roads, railways and airways stretches almost 7,700 km (4,800 mi) from Kaliningrad in the west to the Kamchatka Peninsula in the east, and major cities such as Moscow and Saint Petersburg are served by extensive rapid transit systems.

<span class="mw-page-title-main">Broad-gauge railway</span> Rail track gauge wider than 4 ft 8 1/2 in

A broad-gauge railway is a railway with a track gauge broader than the 1,435 mm used by standard-gauge railways.

<span class="mw-page-title-main">Track gauge</span> Spacing of the rails on a railway track

In rail transport, track gauge is the distance between the two rails of a railway track. All vehicles on a rail network must have wheelsets that are compatible with the track gauge. Since many different track gauges exist worldwide, gauge differences often present a barrier to wider operation on railway networks.

The Trans-Asian Railway(TAR) is a project to create an integrated freight railway network across Europe and Asia. The project is of the United Nations Economic and Social Commission for Asia and the Pacific (UNESCAP).

In railway engineering, "gauge" is the transverse distance between the inner surfaces of the heads of two rails, which for the vast majority of railway lines is the number of rails in place. However, it is sometimes necessary for track to carry railway vehicles with wheels matched to two different gauges. Such track is described as dual gauge – achieved either by addition of a third rail, if it will fit, or by two additional rails. Dual-gauge tracks are more expensive to configure with signals and sidings, and to maintain, than two separate single-gauge tracks. It is therefore usual to build dual-gauge or other multi-gauge tracks only when necessitated by lack of space or when tracks of two different gauges meet in marshalling yards or passenger stations. Dual-gauge tracks are by far the most common configuration, but triple-gauge tracks have been built in some situations.

<span class="mw-page-title-main">Transporter wagon</span>

A transporter wagon, in railway terminology, is a wagon (UIC) or railroad car (US) designed to carry other railway equipment. Normally, it is used to transport equipment of a different rail gauge. In most cases, a transporter wagon is a narrower gauge wagon for transporting a wider gauge equipment, allowing freight in a wider gauge wagons to reach destinations on the narrower gauge network without the expense and time of transshipment into a narrower gauge wagons.

<span class="mw-page-title-main">Break of gauge</span> Meeting place of different width rail lines

With railways, a break of gauge occurs where a line of one track gauge meets a line of a different gauge. Trains and rolling stock generally cannot run through without some form of conversion between gauges, leading to passengers having to change trains and freight requiring transloading or transshipping; this can add delays, costs, and inconvenience to travel on such a route.

<span class="mw-page-title-main">Trans-Mongolian Railway</span> International railway line in Mongolia

The Trans-Mongolian Railway connects Ulan-Ude on the Trans-Siberian Railway in Buryatia, Russia, with Ulanqab in Inner Mongolia, China, via Ulaanbaatar, the capital of Mongolia. It was completed in 1956, and runs from northwest to southeast with major stations at Naushki/Sükhbaatar on the Russian border, Darkhan, Züünkharaa, Choir, Sainshand, and Zamyn-Üüd/Erenhot on the Chinese border, where the railway changes from single-track to double-track and its gauge changes from 1,520 mm Russian gauge to 1,435 mm standard gauge. The railway also has important branch lines to Erdenet and Baganuur.

<span class="mw-page-title-main">Islamic Republic of Iran Railways</span> State-owned rail company

The Islamic Republic of Iran Railways is the national state-owned railway system of Iran. The Raja Passenger Train Company is an associate of the IR, and manages its passenger trains. The Railway Transportation Company is an associate of the IR, which manages its freight transport. The Ministry of Roads & Urban Development is the state agency that oversees the IRIR. Some 33 million tonnes of goods and 29 million passengers are transported annually by the rail transportation network, accounting for 9 percent and 11 percent of all transportation in Iran, respectively (2011).

<span class="mw-page-title-main">5 ft and 1520 mm gauge railways</span> Railway track gauge

Railways with a railway track gauge of 5 ft first appeared in the United Kingdom and the United States. This gauge became commonly known as "Russian gauge", because the government of the Russian Empire chose it in 1843. Former areas and states of the Empire have inherited this standard. However in 1970, Soviet Railways re-defined the gauge as 1,520 mm.

<span class="mw-page-title-main">Variable gauge</span>

A variable gauge system allows railway vehicles in a train to travel across a break of gauge between two railway networks with different track gauges. For through operation, a train must be equipped with special bogies holding variable gauge wheelsets which contain a variable gauge axle (VGA).

Kazakhstan Temir Zholy, also National Company Kazakhstan Temir Zholy, is the national railway company of Kazakhstan.

Dostyk or Druzhba is a small town in Kazakhstan's Jetisu Region, on the border with Xinjiang, China. It is a port of entry from China. The rail portion serves as an important link in the Eurasian Land Bridge. It is situated in the Dzungarian Gate, a historically significant mountain pass.

<span class="mw-page-title-main">Rail transport in Turkey</span>

Turkey has a state-owned railway system built to standard gauge which falls under the remit of the Ministry of Transportation and Infrastructure. The primary rail carrier is the Türkiye Cumhuriyeti Devlet Demiryolları (TCDD) which is responsible for all long-distance and cross-border freight and passenger trains. A number of other companies operate suburban passenger trains in urban conurbations.

The railcar couplers or couplings listed, described, and depicted below are used worldwide on legacy and modern railways. Compatible and similar designs are frequently referred to using widely differing make, brand, regional or nick names, which can make describing standard or typical designs confusing. Dimensions and ratings noted in these articles are usually of nominal or typical components and systems, though standards and practices also vary widely with railway, region, and era. Transition between incompatible coupler types may be accomplished using dual couplings, a coupling adapter or a barrier wagon.

<span class="mw-page-title-main">Track gauge in Europe</span> Railway Gauges

Most railways in Europe use the standard gauge of 1,435 mm. Some countries use broad gauge, of which there are three types. Narrow gauges are also in use.

<span class="mw-page-title-main">Sakhalin–Hokkaido Tunnel</span> Proposed tunnel between Russia and Japan

The Sakhalin–Hokkaido Tunnel is a proposed connection to link the Russian island of Sakhalin with the Japanese island of Hokkaido. Cost estimates by Russia in the year 2000 put the project to span the 45-kilometre (28-mile) strait at $50 billion.

<span class="mw-page-title-main">TU7 diesel locomotive</span>

TU7 (ТУ7) - Soviet, later Russian diesel locomotive for gauge 750 mm1,067 mm.

<span class="mw-page-title-main">Kambarka Engineering Works</span> Rolling stock manufacturer

Kambarka Engineering Works - Full name: Open Joint Stock Company «Kambarka Engineering Works». A rolling stock manufacturer, located in the city of Kambarka (Udmurt), Russia.

<span class="mw-page-title-main">TU8P</span>

TU8P (ТУ8П) is a Soviet, later Russian diesel locomotive, railcar or draisine for gauge 750 mm.

References

  1. Grafton T. Nutter, Improvement in Apparatus for Lifting Locomotives, Trucks, and Railroad Cars, U.S. patent 114,328 , issued May 2, 1871.
  2. John D. Imboden, Improvement in Railway-Car Lifters, U.S. patent 170,374 , issued Sept. 25, 1875.
  3. Catch Point - November 2007 - p35 - picture of lowering method
  4. Charles D. Tisdale, Improvement in Connecting and Disconnecting Car-Bodies and Trucks, U.S. patent 139,835 , issued June 10, 1873.
  5. George W. Atkinson, Apparatus for Changing Car-Trucks, U.S. patent 265,366 , issued Oct. 3, 1882.
  6. Robert H. Ramsey, Car and Freight Transfer Apparatus, U.S. patent 304,562 , issued Sept. 2, 1884.
  7. Bureau of Transport Economics (1977-02-02). A Study of Port Pirie Bogie Exchange (Report). Australian Government Publishing Service. Retrieved 2022-11-11.
  8. "Railway Gauges" (TXT). TrainWeb. Archived from the original on 2021-03-01. Retrieved 2022-11-11.
  9. "Ian Patterson & Partners: About". Archived from the original on 2008-07-18. Retrieved 2022-11-11.
  10. Australian Academy of Technological Sciences and Engineering (1988). Technology in Australia 1788–1988. Australian Science and Technology Heritage Centre. p. 477. ISBN   0908029497 . Retrieved 2022-11-11.
  11. Lee, Robert (2007-08-01). The Railways of Victoria 1854–2004. Melbourne University Publishing Ltd. p. 224. ISBN   9780522851342.
  12. USpatent 4102459,Schelle, Axel&Nell, Kuno,"Adaptor device for coupling railway vehicles having different types of couplers",issued 1978-07-25, assigned to Knorr-Bremse GmbH
  13. Jerzyło, Patrycja, ed. (October 2016). Księga Jubileuszowa z okazji 10-lecia kształcenia na kierunku Transport (PDF) (in Polish). Gdańsk: Fundacja Rozwoju Inżynierii Lądowej. p. 66. ISBN   978-83-922034-7-6.
  14. "Urządzenie do przestawiania wozów kolejowych z torów o szerokości normalnej na tory szerokie (rossyjskie) i odwrotnie, bez przeładowywania towarów" [Device to change railway wagons from standard gauge to broad (Russian) gauge tracks and back, without unloading]. Przegląd Techniczny (in Polish). XL (43): 521–524. 23 October 1902 via BCPW (Warsaw University of Technology Central Library).
  15. Wasiutyński, Aleksander (1925). Drogi żelazne [Railways] (in Polish) (2nd ed.). Warsaw: Komisja Wydawnicza T-wa Bratniej Pomocy Studentów Politechniki Warszawskiej. p. 170 via BCPW (Warsaw University of Technology Central Library).
  16. "Breidsprecher break of gauge device" (PDF). Locomotive Magazine and Railway Carriage and Wagon Review. 44 (550): 184–185. 15 June 1938. Archived from the original on 13 August 2021.
  17. Helmut (9 March 2013). "36 hours in North Korea without a guide..." Vienna-Pyongyang.Blogspot.com. Retrieved 13 March 2017.
  18. Trains (magazine), March 2009, p68
  19. Сахалинская узкоколейная железная дорога (The narrow-gauge railways of Sakhalin) Archived 2011-08-26 at the Wayback Machine (in Russian)
  20. 1 2 3 Minner v. Sedalia, W. & S. W. Ry. Co., The South Western Reporter Vol. 66, West, 1902; pages 1072-1079. For B&NW and D&RGW practice, see page 1075.
  21. Frank S. Bond, A Southern Pacific Railroad, in Southwestern Pacific Railroad, , C. E. Ware & Co., 1875; pages 17-20, see page 18 for truck exchange.
  22. Kenneth C. Springirth, East Broad Top Railroad, Arcadia, Charleston SC, 2008; page 28.
  23. "East Broad Top Prepares for a Big 2021". 26 January 2021.
  24. 1 2 The Urbana Hoist, American Railroad Journal, Vol. XXXIII, No. 1 (Jan. 6, 1877); page 30.
  25. 1 2 Edward Vernon, The Decline in Railroad Construction, Editorial, American Railroad Manual New York, 1874; page li.
  26. Paul Selev, Our Next-Door Neighbor, The Inland Printer, Vol. VII, No. 7 (April, 1890); page 651.
  27. T.M.R. Talcott, Improvements at North Danville, General Manager's Report, Proceedings of the Annual Meeting of the Stockholders of the Virginia Midland Railway Company, Alexandria, 1882; page 58.
  28. Titus v. Bradford, Bordell & Kinzua Railroad Company, Lancaster Law Review, Vol. VIII No. 12 (Feb. 16, 1891); pages 93-95.
  29. "Train timetable". RW.by. Retrieved 13 March 2017.