A clothes dryer (tumble dryer, drying machine, or simply dryer) is a powered household appliance that is used to remove moisture from a load of clothing, bedding and other textiles, usually after they are washed in the washing machine.
Many dryers consist of a rotating drum called a "tumbler" through which heated air is circulated to evaporate moisture while the tumbler is rotated to maintain air space between the articles. Using such a machine may cause clothes to shrink or become less soft (due to loss of short soft fibers). A simpler non-rotating machine called a "drying cabinet" may be used for delicate fabrics and other items not suitable for a tumble dryer. Other machines include steam to de-shrink clothes and avoid ironing. [1]
Tumble dryers continuously draw in the ambient air around them and heat it before passing it through the tumbler. The resulting hot, humid air is usually vented outside to make room for more air to continue the drying process.
Tumble dryers are sometimes integrated with a washing machine, in the form of washer-dryer combos, which are essentially a front loading washing machine with an integrated dryer or (in the US) a laundry center, which stacks the dryer on top of the washer and integrates the controls for both machines into a single control panel. Often the washer and dryer functions will have a different capacity, with the dryer usually having a lower capacity than the washer. Tumble dryers can also be top loading, in which the drum is loaded from the top of the machine and the drum's end supports are in the left and right sides, instead of the more conventional front and rear. They can be as thin as 40 centimetres (16 in) in width, and may include detachable stationary racks for drying items like plush toys and footwear. [2]
These centrifuge machines simply spin their drums much faster than a typical washer could, in order to extract additional water from the load. They may remove more water in two minutes than a heated tumbler dryer can in twenty, thus saving significant amounts of time and energy. Although spinning alone will not completely dry clothing, this additional step saves a worthwhile amount of time and energy for large laundry operations such as those of hospitals.
Just as in a tumble dryer, condenser or condensation dryers pass heated air through the load. However, instead of exhausting this air, the dryer uses a heat exchanger to cool the air and condense the water vapor into either a drain pipe or a collection tank. The drier air is run through the loop again. The heat exchanger typically uses ambient air as its coolant, therefore the heat produced by the dryer will go into the immediate surroundings instead of the outside, increasing the room temperature. In some designs, cold water is used in the heat exchanger, eliminating this heating, but requiring increased water usage.
In terms of energy use, condenser dryers typically require around 2 kilowatt hours (kW⋅h) of energy per average load. [3]
Because the heat exchange process simply cools the internal air using ambient air (or cold water in some cases), it will not dry the air in the internal loop to as low a level of humidity as typical fresh, ambient air. As a consequence of the increased humidity of the air used to dry the load, this type of dryer requires somewhat more time than a tumble dryer. Condenser dryers are a particularly attractive option where long, intricate ducting would be required to vent the dryer.
A closed-cycle heat pump clothes dryer uses a heat pump to dehumidify the processing air. Such dryers typically use under half the energy per load of a condenser dryer.
Whereas condensation dryers use a passive heat exchanger cooled by ambient air, these dryers use a heat pump. The hot, humid air from the tumbler is passed through a heat pump where the cold side condenses the water vapor into either a drain pipe or a collection tank and the hot side reheats the air afterward for re-use. In this way not only does the dryer avoid the need for ducting, but it also conserves much of its heat within the dryer instead of exhausting it into the surroundings. Heat pump dryers can, therefore, use up to 50% less energy required by either condensation or conventional electric dryers. Heat pump dryers use about 1 kW⋅h of energy to dry an average load instead of 2 kW⋅h for a condenser dryer, or from 3 to 9 kW⋅h, for a conventional electric dryer. [4] [5] [3] Domestic heat pump dryers are designed to work in typical ambient temperatures from 5 to 30 °C (41 to 86 °F). Below 5 °C (41 °F), drying times significantly increase.
As with condensation dryers, the heat exchanger will not dry the internal air to as low a level of humidity as the typical ambient air. With respect to ambient air, the higher humidity of the air used to dry the clothes has the effect of increasing drying times; however, because heat pump dryers conserve much of the heat of the air they use, the already-hot air can be cycled more quickly, possibly leading to shorter drying times than tumble dryers, depending on the model.
A new type of dryer in development, these machines are a more advanced version of heat pump dryers. Instead of using hot air to dry the clothing, mechanical steam compression dryers use water recovered from the clothing in the form of steam. First, the tumbler and its contents are heated to 100 °C (212 °F). The wet steam that results purges the system of air and is the only remaining atmosphere in the tumbler.
As wet steam exits the tumbler, it is mechanically compressed (hence the name) to extract water vapor and transfer the heat of vaporization to the remaining gaseous steam. This pressurized, gaseous steam is then allowed to expand, and is superheated before being injected back into the tumbler where its heat causes more water to vaporize from the clothing, creating more wet steam and restarting the cycle.
Like heat pump dryers, mechanical steam compression dryers recycle much of the heat used to dry the clothes, and they operate in a very similar range of efficiency as heat pump dryers. Both types can be over twice as efficient as conventional tumble dryers. The considerably higher temperatures used in mechanical steam compression dryers result in drying times on the order of half as long as those of heat pump dryers. [6]
Marketed by some manufacturers as a "static clothes drying technique", convectant dryers simply consist of a heating unit at the bottom, a vertical chamber, and a vent at top. The unit heats air at the bottom, reducing its relative humidity, and the natural tendency of hot air to rise brings this low-humidity air into contact with the clothes. This design is slower than conventional tumble dryers, but relatively energy-efficient if well-implemented. It works particularly well in cold and humid environments, where it dries clothes substantially faster than line-drying. In hot and dry weather, the performance delta over line-drying is negligible.
Given that this is a relatively simple and cheap technique to materialize, most consumer products showcase the added benefit of portability and/or modularity. Newer designs implement a fan heater at the bottom to pump hot air into the vertical drying rack chamber. Temperatures in excess of 60 °C (140 °F) can be reached inside these "hot air balloons," yet lint, static cling, and shrinkage are minimal. Upfront cost is significantly lower than tumble, condenser and heat pump designs.
If used in combination with washing machines featuring fast spin cycles (800+ rpm) or spin dryers, the cost-effectiveness of this technique has the potential to render tumble dryer-like designs obsolete in single-person and small family households. One disadvantage is that the moisture from the clothes is released into the immediate surroundings. Proper ventilation or a complementary dehumidifier is recommended for indoor use. It also cannot compete with the tumble dryer's capacity to dry multiple loads of wet clothing in a single day.
The solar dryer is a box-shaped stationary construction which encloses a second compartment where the clothes are held. It uses the sun's heat without direct sunlight reaching the clothes. Alternatively, a solar heating box may be used to heat air that is driven through a conventional tumbler dryer.
Japanese manufacturers [7] have developed highly efficient clothes dryers that use microwave radiation to dry the clothes (though a vast majority of Japanese air dry their laundry). Most of the drying is done using microwaves to evaporate the water, but the final drying is done by convection heating, to avoid problems of arcing with metal pieces in the laundry. [8] [9] There are a number of advantages: shorter drying times (25% less), [10] energy savings (17–25% less), and lower drying temperatures. Some analysts think that the arcing and fabric damage is a factor preventing microwave dryers from being developed for the US market. [11] [12]
Ultrasonic dryers use high-frequency signals to drive piezoelectric actuators in order to mechanically shake the clothes, releasing water in the form of a mist which is then removed from the drum. They have the potential to significantly cut energy consumption while needing only one-third of the time needed by a conventional electric dryer for a given load. [13] They also do not have the same issues related with lint in most other types of dryers. [14]
Some manufacturers, like LG Electronics and Whirlpool, have introduced hybrid dryers, that offer the user the option of using either a heat pump or a traditional electric heating element for drying the user's clothes. Hybrid dryers can also use a heat pump and a heating element at the same time to dry clothes faster.
Clothes dryers can cause static cling through the triboelectric effect. This can be a minor nuisance and is often a symptom of over-drying textiles to below their equilibrium moisture level, particularly when using synthetic materials. Fabric conditioning products such as dryer sheets are marketed to dissipate this static charge, depositing surfactants onto the fabric load by mechanical abrasion during tumbling. [15] Modern dryers often have improved temperature and humidity sensors and electronic controls which aim to stop the drying cycle once textiles are sufficiently dry, avoiding over-drying and the static charge and energy wastage this causes.
Drying at a minimum of 60 °C (140 °F) heat for thirty minutes kills many parasites including house dust mites, [16] bed bugs, [17] and scabies mites [18] and their eggs; a bit more than ten minutes kills ticks. [19] Simply washing drowns dust mites, and exposure to direct sunlight for three hours kills their eggs. [16]
Moisture and lint are byproducts of the tumble drying process and are pulled from the drum by a fan motor and then pushed through the remaining exhaust conduit to the exterior termination fitting. Typical exhaust conduit comprises flex transition hose found immediately behind the dryer, the 4-inch (100 mm) rigid galvanized pipe and elbow fittings found within the wall framing, and the vent duct hood found outside the house.
A clean, unobstructed dryer vent improves both the efficiency and safety of the dryer. As the dryer duct pipe becomes partially obstructed and filled with lint, drying time markedly increases and causes the dryer to waste energy. A blocked vent increases the internal temperature and may result in a fire. Clothes dryers are one of the more costly home appliances to operate. [20]
Several factors can contribute to or accelerate rapid lint build-up. These include long or restrictive ducts, bird or rodent nests in the termination, crushed or kinked flex transition hose, terminations with screen-like features, and condensation within the duct due to un-insulated ducts traveling through cold spaces such as a crawl space or attic. If plastic flaps are at the outside end of the duct, one may be able to flex, bend, and temporarily remove the plastic flaps, clean the inside surface of the flaps, clean the last foot or so of the duct, and reattach the plastic flaps. The plastic flaps keep insects, birds, and snakes [21] out of the dryer vent pipe. During cold weather, the warm wet air condenses on the plastic flaps, and minor trace amounts of lint sticks to the wet inside part of the plastic flaps at the outside of the building. [22] [23]
Ventless dryers include multi-stage lint filtration systems and some even include automatic evaporator and condenser cleaning functions that can run even while the dryer is running. The evaporator and condenser are usually cleaned with running water. These systems are necessary, in order to prevent lint from building up inside the dryer and evaporator and condenser coils.
Aftermarket add-on lint and moisture traps can be attached to the dryer duct pipe, on machines originally manufactured as outside-venting, to facilitate installation where an outside vent is not available. Increased humidity at the location of installation is a drawback to this method. [24]
Dryers expose flammable materials to heat. Underwriters Laboratories [25] recommends cleaning the lint filter after every cycle for safety and energy efficiency, provision of adequate ventilation, and cleaning of the duct at regular intervals. [26] UL also recommends that dryers not be used for glass fiber, rubber, foam or plastic items, or any item that has had a flammable substance spilled on it.
In the United States, the US Fire Administration [27] in a 2012 report estimated that from 2008 to 2010, fire departments responded to an estimated 2,900 clothes dryer fires in residential buildings each year across the nation. These fires resulted in an annual average loss of 5 deaths, 100 injuries, and $35 million in property loss. The Fire Administration attributes "Failure to clean" (34%) as the leading factor contributing to clothes dryer fires in residential buildings, and observed that new home construction trends place clothes dryers and washing machines in more hazardous locations away from outside walls, such as in bedrooms, second-floor hallways, bathrooms, and kitchens.
To address the problem of clothes dryer fires, a fire suppression system can be used with sensors to detect the change in temperature when a blaze starts in a dryer drum. These sensors then activate a water vapor mechanism to put out the fire. [28]
The environmental impact of clothes dryers is especially severe in the US and Canada, where over 80% of all homes have a clothes dryer. According to the US Environmental Protection Agency, if all residential clothes dryers sold in the US were energy efficient, "the utility cost savings would grow to more than $1.5 billion each year and more than 10 billion kilograms (22 billion pounds) of annual greenhouse gas emissions would be prevented”. [29]
Clothes dryers are second only to refrigerators and freezers as the largest residential electrical energy consumers in America. [30]
In the European Union, the EU energy labeling system is applied to dryers; dryers are classified with a label from A+++ (best) to G (worst) according to the amount of energy used per kilogram of clothes (kW⋅h/kg). Sensor dryers can automatically sense that clothes are dry and switch off. This means over-drying is not as frequent. Most of the European market sells sensor dryers now, and they are normally available in condenser and vented dryers.
A hand-cranked clothes dryer was created in 1800 by M. Pochon from France. [31] Henry W. Altorfer invented and patented an electric clothes dryer in 1937. [32] J. Ross Moore, an inventor from North Dakota, developed designs for automatic clothes dryers and published his design for an electrically operated dryer in 1938. [33] Industrial designer Brooks Stevens developed an electric dryer with a glass window in the early 1940s. [34]
Evaporation is a type of vaporization that occurs on the surface of a liquid as it changes into the gas phase. A high concentration of the evaporating substance in the surrounding gas significantly slows down evaporation, such as when humidity affects rate of evaporation of water. When the molecules of the liquid collide, they transfer energy to each other based on how they collide. When a molecule near the surface absorbs enough energy to overcome the vapor pressure, it will escape and enter the surrounding air as a gas. When evaporation occurs, the energy removed from the vaporized liquid will reduce the temperature of the liquid, resulting in evaporative cooling.
Heating, ventilation, and air conditioning (HVAC) is the use of various technologies to control the temperature, humidity, and purity of the air in an enclosed space. Its goal is to provide thermal comfort and acceptable indoor air quality. HVAC system design is a subdiscipline of mechanical engineering, based on the principles of thermodynamics, fluid mechanics, and heat transfer. "Refrigeration" is sometimes added to the field's abbreviation as HVAC&R or HVACR, or "ventilation" is dropped, as in HACR.
A washing machine is a machine designed to launder clothing. Modern-day home appliances use electric power to automatically clean clothes. The term is mostly applied to machines that use water as opposed to dry cleaning or ultrasonic cleaners. The user adds laundry detergent, which is sold in liquid, powder, or dehydrated sheet form, to the wash water.
Dry cleaning is any cleaning process for clothing and textiles using a solvent other than water. Clothes are instead soaked in a water-free liquid solvent. Tetrachloroethylene (perchloroethylene), known in the industry as "perc", is the most commonly used solvent, although alternative solvents such as 1-bromopropane, hydrocarbons, and supercritical CO2 are also used.
A boiler is a closed vessel in which fluid is heated. The fluid does not necessarily boil. The heated or vaporized fluid exits the boiler for use in various processes or heating applications, including water heating, central heating, boiler-based power generation, cooking, and sanitation.
A dehumidifier is an air conditioning device which reduces and maintains the level of humidity in the air. This is done usually for health or thermal comfort reasons, or to eliminate musty odor and to prevent the growth of mildew by extracting water from the air. It can be used for household, commercial, or industrial applications. Large dehumidifiers are used in commercial buildings such as indoor ice rinks and swimming pools, as well as manufacturing plants or storage warehouses. Typical air conditioning systems combine dehumidification with cooling, by operating cooling coils below the dewpoint and draining away the water that condenses.
An evaporative cooler is a device that cools air through the evaporation of water. Evaporative cooling differs from other air conditioning systems, which use vapor-compression or absorption refrigeration cycles. Evaporative cooling exploits the fact that water will absorb a relatively large amount of heat in order to evaporate. The temperature of dry air can be dropped significantly through the phase transition of liquid water to water vapor (evaporation). This can cool air using much less energy than refrigeration. In extremely dry climates, evaporative cooling of air has the added benefit of conditioning the air with more moisture for the comfort of building occupants.
A cooling tower is a device that rejects waste heat to the atmosphere through the cooling of a coolant stream, usually a water stream, to a lower temperature. Cooling towers may either use the evaporation of water to remove heat and cool the working fluid to near the wet-bulb air temperature or, in the case of dry cooling towers, rely solely on air to cool the working fluid to near the dry-bulb air temperature using radiators.
A chiller is a machine that removes heat from a liquid coolant via a vapor-compression, adsorption refrigeration, or absorption refrigeration cycles. This liquid can then be circulated through a heat exchanger to cool equipment, or another process stream. As a necessary by-product, refrigeration creates waste heat that must be exhausted to ambience, or for greater efficiency, recovered for heating purposes. Vapor compression chillers may use any of a number of different types of compressors. Most common today are the hermetic scroll, semi-hermetic screw, or centrifugal compressors. The condensing side of the chiller can be either air or water cooled. Even when liquid cooled, the chiller is often cooled by an induced or forced draft cooling tower. Absorption and adsorption chillers require a heat source to function.
A clothes line, also spelled clothesline, also known as a washing line, is a device for hanging clothes on for the purpose of drying or airing out the articles. It is made of any type of rope, cord, or twine that has been stretched between two points, outdoors or indoors, above ground level. Clothing that has recently been washed is hung over the line to dry, held in place using clothes pegs or clothespins. Washing lines are attached either from a post or a wall, and are frequently located in back gardens, or on balconies. Longer washing lines often have props holding up the mid-section so the weight of the clothing does not pull the clothesline down to the ground.
In aeronautics, an environmental control system (ECS) of an aircraft is an essential component which provides air supply, thermal control and cabin pressurization for the crew and passengers. Additional functions include the cooling of avionics, smoke detection, and fire suppression.
A thermal power station is a type of power station in which heat energy is converted to electrical energy. In a steam-generating cycle heat is used to boil water in a large pressure vessel to produce high-pressure steam, which drives a steam turbine connected to an electrical generator. The low-pressure exhaust from the turbine enters a steam condenser where it is cooled to produce hot condensate which is recycled to the heating process to generate more high pressure steam. This is known as a Rankine cycle.
The steam-electric power station is a power station in which the electric generator is steam driven. Water is heated, turns into steam and spins a steam turbine which drives an electrical generator. After it passes through the turbine, the steam is condensed in a condenser. The greatest variation in the design of steam-electric power plants is due to the different fuel sources.
A combo washer dryer is a combination in a single cabinet of a washing machine and a clothes dryer. It should not be confused with a "stackable" combination of a separate washing machine and a separate clothes dryer.
Radiators are heat exchangers used for cooling internal combustion engines, mainly in automobiles but also in piston-engined aircraft, railway locomotives, motorcycles, stationary generating plants or any similar use of such an engine.
HVAC is a major sub discipline of mechanical engineering. The goal of HVAC design is to balance indoor environmental comfort with other factors such as installation cost, ease of maintenance, and energy efficiency. The discipline of HVAC includes a large number of specialized terms and acronyms, many of which are summarized in this glossary.
Grain drying is the process of drying grain to prevent spoilage during storage. The grain drying described in this article is that which uses fuel- or electric-powered processes supplementary to natural ones, including swathing/windrowing for drying by ambient air and sunshine, or stooking before threshing.
Vacuum drying is the mass transfer operation in which the moisture present in a substance, usually a wet solid, is removed by means of creating a vacuum.
Fabric treatments are processes that make fabric softer, or water resistant, or enhance dye penetration after they are woven. Fabric treatments get applied when the textile itself cannot add other properties. Treatments include, scrim, foam lamination, fabric protector or stain repellent, anti microbial and flame retardant.
A drying room is a room intended for drying objects. It can act as a replacement or complement for drying cabinets, tumble-dryers, and outdoor drying. Compared to outdoor drying, a drying room means one usually does not have to consider the weather forecast in case of rain.
{{cite web}}
: CS1 maint: archived copy as title (link)