An evaporator, distiller or distilling apparatus is a piece of ship's equipment used to produce fresh drinking water from sea water by distillation. As fresh water is bulky, may spoil in storage, and is an essential supply for any long voyage, the ability to produce more fresh water in mid-ocean is important for any ship.
Although distillers are often associated with steam ships, their use pre-dates this. Obtaining fresh water from seawater is a theoretically simple system that, in practice, presented many difficulties. While there are numerous effective methods today, early desalination efforts had low yields and often could not produce potable water. [1]
At first, only larger warships and some exploratory ships were fitted with distilling apparatus: a warship's large crew naturally needed a large supply of water, more than they could stow on board in advance. Cargo ships, with their smaller crews, merely carried their supplies with them. A selection of documented systems is as follows:
With the development of the marine steam engine, their boilers also required a continual supply of feedwater.
Early boilers used seawater directly, but this gave problems with the build-up of brine and scale. [20] For efficiency, as well as conserving feedwater, marine engines have usually been condensing engines. By 1865, the use of an improved surface condenser permitted the use of fresh water feed, [21] as the additional feedwater now required was only the small amount required to make up for losses, rather than the total passed through the boiler. Despite this, fresh water makeup to the feedwater system of a large warship under full power could still require up to 100 tons per day. [22] Attention was also paid to de-aereating feedwater, to further reduce boiler corrosion. [21]
The distillation system for boiler feedwater at this time was usually termed an evaporator, partly to distinguish it from a separate system or distiller used for drinking water. Separate systems were often used, especially in early systems, owing to the problem of contamination from oily lubricants in the feedwater system and because of the greatly different capacities required in larger ships. In time, the two functions became combined and the two terms were applied to the separate components of the system.
The first water supply by distillation of boiler steam appeared on early paddle steamers and used a simple iron box in the paddle boxes, cooled by water splash. A steam supply direct from the boiler, avoiding the engine and its lubricants, was led to them. [15] With the development of steam heating jackets around the cylinders of engines such as the trunk engine, the exhaust from this source, again unlubricated, could be condensed. [15]
The first distilling plants that boiled a separate water supply from that of the main boiler, appeared around 1867. [15] These were not directly heated by a flame, but had a primary steam circuit using main boiler steam through coils within a steam drum or evaporator. [23] The distillate from this vessel then passed to an adjacent vessel, the distilling condenser. [23] As these evaporators used a 'clean' seawater supply directly, rather than contaminated water from the boiler circuit, they could be used to supply both feedwater and drinking water. These double distillers appeared around 1884. [15] For security against failure, ships except the smallest were fitted with two sets. [23]
Evaporators consume a great deal of steam, and thus fuel, in relation to the quantity of fresh water produced. Their efficiency is improved by working them at a partial vacuum, supplied by the main engine condensers. [23] [24] [25] On modern diesel-powered ships, this vacuum can instead be produced by an ejector, usually worked by the output from the brine pump. Working under vacuum also reduces the temperature required to boil seawater and thus permits evaporators to be used with lower-temperature waste heat from the diesel cooling system.
One of the greatest operational problems with an evaporator is the build-up of scale. Its design is tailored to reduce this, and to make its cleaning as effective as possible. The usual design, as developed by Weir and the Admiralty, is for a vertical cylindrical drum, heated by steam-carrying drowned coils in the lower portion. [24] As they are entirely submerged, they avoid the most active region for the deposition of scale, around the waterline. Each coil consists of one or two spirals in a flat plane. Each coil is easily removed for cleaning, being fastened by individual pipe unions through the side of the evaporator. A large door is also provided, allowing the coils to be removed or replaced. Cleaning may be carried out mechanically, with a manual scaling hammer. [25] This also has a risk of mechanical damage to the tubes, as the slightest pitting tends to act as a nucleus for scale or corrosion. [25] It is also common practice to break light scaling free by thermal shock, by passing steam through the coils without cooling water present [23] [25] or by heating the coils, then introducing cold seawater. [26] In 1957, the trials ship HMS Cumberland, an obsolete heavy cruiser, was used for the first tests of the 'flexing element' distiller, where non-rigid heating coils flexed continually in service and so broke the scale free as soon as it formed a stiff layer.
Despite the obvious salinity of seawater, salt is not a problem for deposition until it reaches the saturation concentration. [20] As this is around seven times that of seawater and evaporators are only operated to a concentration of two and a half times, [27] this is not a problem in service.
A greater problem for scaling is the deposition of calcium sulphate. [24] The saturation point for this compound decreases with temperature above 60 °C (140 °F), so that beginning from around 90 °C (194 °F) a hard and tenacious deposit is formed.
To further control scale formation, equipment may be provided to automatically inject a weak citric acid solution into the seawater feed. The ratio is 1:1350, by weight of seawater. [28]
Operation of an evaporator represents a costly consumption of main boiler steam, thus fuel. Evaporators for a warship must also be adequate to supply the boilers at continuous full power when required, even though this is rarely required. Varying the vacuum under which the evaporator works, and thus the boiling point of the feedwater, may optimise production for either maximum output, or better efficiency, depending on which is needed at the time. Greatest output is achieved when the evaporator operates at near atmospheric pressure and a high temperature (for saturated steam this will be at a limit of 100 °C), which may then have an efficiency of 0.87 kg of feedwater produced for each kg of steam supplied. [24]
If condenser vacuum is increased to its maximum, evaporator temperature may be reduced to around 72 °C. Efficiency increases until the mass of feedwater produced almost equals that of the supplied steam, although production is now restricted to 86% of the previous maximum. [24]
Evaporators are generally installed as a set, where two evaporators are coupled to a single distiller. [29] For reliability, large ships will then have a pair of these sets. [29] It is possible to arrange these sets of evaporators in either parallel or in series, for either maximum or most efficient production. [24] This arranges the two evaporators so that the first operates at atmospheric pressure and high temperature (the maximum output case), but then uses the resultant hot output from the first evaporator to drive a second, running at maximum vacuum and low temperature (the maximum efficiency case). [29] The overall output of feedwater may exceed the weight of steam first supplied, as up to 160% of it. Capacity is however reduced, to 72% of the maximum. [24]
The unevaporated seawater in an evaporator gradually becomes a concentrated brine and, like the early steam boilers with seawater feed, this brine must be intermittently blown down every six to eight hours and dumped overboard. [23] Early evaporators were simply mounted high-up and dumped their brine by gravity. [15] As the increasing complexity of surface condensers demanded better feedwater quality, a pump became part of the evaporator equipment. [23] This pump had three combined functions as a seawater feed pump, a fresh water delivery pump and a brine extraction pump, each of progressively smaller capacity. [22] The brine salinity was an important factor in evaporator efficiency: too dense encouraged scale formation, but too little represented a waste of heated seawater. The optimum operating salinity was thus fixed at three times that of seawater, and so the brine pump had to remove at least one third of the total feedwater supply rate. [30] These pumps resembled the steam-powered reciprocating feedwater pumps already in service. They were usually produced by the well-known makers, such as G & J Weir. Vertical and horizontal pumps were used, although horizontal pumps were favoured as they encouraged the de-aeration of feedwater. Electrically powered rotary centrifugal pumps were later adopted, as more efficient and more reliable. There were initial concerns whether these would be capable of pumping brine against the vacuum of the evaporator and so there was also a transitional type where a worm gear-driven plunger pump for brine was driven from the rotary shaft. [22]
A later form of marine evaporator is the flash distiller. [31] Heated seawater is pumped into a vacuum chamber, where it 'flashes' into pure water vapour. This is then condensed for further use.
As the use of vacuum reduces the vapour pressure, the seawater need only be raised to a temperature of 77 °C (171 °F). [lower-roman 1] Both evaporator and distiller are combined into a single chamber, although most plants use two joined chambers, worked in series. The first chamber is worked at 23.5 inHg (80 kPa ) vacuum, the second at 26–27 inHg (88–91 kPa). [31] Seawater is supplied to the distiller by a pump at around 20 pounds per square inch (140 kPa). The cold seawater passes through a condenser coil in the upper part of each chamber before being heated by steam in an external feedwater heater. The heated seawater enters the lower part of the first chamber, then drains over a weir and passes to the second chamber, encouraged by the differential vacuum between them. The brine produced by a flash distiller is only slightly concentrated and is pumped overboard continuously. [31]
Fresh water vapour rises through the chambers and is condensed by the seawater coils. Baffles and catchment trays capture this water in the upper part of the chamber. Vacuum itself is maintained by steam ejectors. [31]
The advantage of the flash distiller over the compound evaporator is its greater operating efficiency, in terms of heat supplied. This is due to working under vacuum, thus low temperature, and also the regenerative use of the condenser coils to pre-heat the seawater feed. [31]
A limitation of the flash distiller is its sensitivity to seawater inlet temperature, as this affects the efficiency of the condenser coils. In tropical waters, the distiller flowrate must be throttled to maintain effective condensation. [31] As these systems are more modern, they are generally fitted with an electric salinometer and some degree of automatic control. [31]
Diesel-powered motorships do not use steam boilers as part of their main propulsion system and so may not have steam supplies available to drive evaporators. Some do, as they use auxiliary boilers for non-propulsion tasks such as this. Such boilers may even be heat-recovery boilers that are heated by the engine exhaust. [32]
Where no adequate steam supply is available, a vapour-compression distiller is used instead. This is driven mechanically, either electrically or by its own diesel engine. [33]
Seawater is pumped into an evaporator, where it is boiled by a heating coil. Vapour produced is then compressed, raising its temperature. This heated vapour is used to heat the evaporator coils. Condensate from the coil outlet provides the fresh water supply. To start the cycle, an electric pre-heater is used to heat the first water supply. The main energy input to the plant is in mechanically driving the compressor, not as heat energy. [33]
Both the fresh water production and the waste brine from the evaporator are led through an output cooler. This acts as a heat exchanger with the inlet seawater, pre-heating it to improve efficiency. The plant may operate at either a low pressure or slight vacuum, according to design. As the evaporator works at pressure, not under vacuum, boiling may be violent. To avoid the risk of priming and a carry over of saltwater into the vapour, the evaporator is divided by a bubble cap separator. [33]
Vapour-compression distillers were installed on US submarines shortly before World War 2. [34] Early attempts had been made with evaporators running from diesel engine exhaust heat, but these could only be used when the submarine was running at speed on the surface. A further difficulty with submarines was the need to produce high-quality water for topping up their large storage batteries. Typical consumption on a war patrol was around 500 US gallons (1,900 litres) per day for hotel services, drinking, cooking, washing [lower-roman 2] etc. and also for replenishing the diesel engine cooling system. A further 500 gallons per week was required for the batteries. [34] The standard Badger model X-1 for diesel submarines could produce 1,000 gallons per day. Tank capacity of 5,600 gallons (1,200 of which was battery water) was provided, around 10 days reserve. [34] With the appearance of nuclear submarines and their plentiful electricity supply, even larger plants could be installed. The X-1 plant was designed so that it could be operated when snorkelling, or even when completely submerged. As the ambient pressure increased when submerged, and thus the boiling point, additional heat was required in these submarine distillers, and so they were designed to run with electric heat continuously. [34]
A steam engine is a heat engine that performs mechanical work using steam as its working fluid. The steam engine uses the force produced by steam pressure to push a piston back and forth inside a cylinder. This pushing force can be transformed, by a connecting rod and crank, into rotational force for work. The term "steam engine" is generally applied only to reciprocating engines as just described, not to the steam turbine. Steam engines are external combustion engines, where the working fluid is separated from the combustion products. The ideal thermodynamic cycle used to analyze this process is called the Rankine cycle. In general usage, the term steam engine can refer to either complete steam plants, such as railway steam locomotives and portable engines, or may refer to the piston or turbine machinery alone, as in the beam engine and stationary steam engine.
Heating, ventilation, and air conditioning (HVAC) is the use of various technologies to control the temperature, humidity, and purity of the air in an enclosed space. Its goal is to provide thermal comfort and acceptable indoor air quality. HVAC system design is a subdiscipline of mechanical engineering, based on the principles of thermodynamics, fluid mechanics, and heat transfer. "Refrigeration" is sometimes added to the field's abbreviation as HVAC&R or HVACR, or "ventilation" is dropped, as in HACR.
The Watt steam engine design became synonymous with steam engines, and it was many years before significantly new designs began to replace the basic Watt design.
A boiler is a closed vessel in which fluid is heated. The fluid does not necessarily boil. The heated or vaporized fluid exits the boiler for use in various processes or heating applications, including water heating, central heating, boiler-based power generation, cooking, and sanitation.
The Rankine cycle is an idealized thermodynamic cycle describing the process by which certain heat engines, such as steam turbines or reciprocating steam engines, allow mechanical work to be extracted from a fluid as it moves between a heat source and heat sink. The Rankine cycle is named after William John Macquorn Rankine, a Scottish polymath professor at Glasgow University.
A chiller is a machine that removes heat from a liquid coolant via a vapor-compression, adsorption refrigeration, or absorption refrigeration cycles. This liquid can then be circulated through a heat exchanger to cool equipment, or another process stream. As a necessary by-product, refrigeration creates waste heat that must be exhausted to ambience, or for greater efficiency, recovered for heating purposes. Vapor compression chillers may use any of a number of different types of compressors. Most common today are the hermetic scroll, semi-hermetic screw, or centrifugal compressors. The condensing side of the chiller can be either air or water cooled. Even when liquid cooled, the chiller is often cooled by an induced or forced draft cooling tower. Absorption and adsorption chillers require a heat source to function.
Multi-stage flash distillation (MSF) is a water desalination process that distills sea water by flashing a portion of the water into steam in multiple stages of what are essentially countercurrent heat exchangers. Current MSF facilities may have as many as 30 stages.
A thermal power station is a type of power station in which heat energy is converted to electrical energy. In a steam-generating cycle heat is used to boil water in a large pressure vessel to produce high-pressure steam, which drives a steam turbine connected to an electrical generator. The low-pressure exhaust from the turbine enters a steam condenser where it is cooled to produce hot condensate which is recycled to the heating process to generate more high pressure steam. This is known as a Rankine cycle.
A surface condenser is a water-cooled shell and tube heat exchanger installed to condense exhaust steam from a steam turbine in thermal power stations. These condensers are heat exchangers which convert steam from its gaseous to its liquid state at a pressure below atmospheric pressure. Where cooling water is in short supply, an air-cooled condenser is often used. An air-cooled condenser is however, significantly more expensive and cannot achieve as low a steam turbine exhaust pressure as a water-cooled surface condenser.
A condensing steam locomotive is a type of locomotive designed to recover exhaust steam, either in order to improve range between taking on boiler water, or to reduce emission of steam inside enclosed spaces. The apparatus takes the exhaust steam that would normally be used to produce a draft for the firebox, and routes it through a heat exchanger, into the boiler water tanks. Installations vary depending on the purpose, design and the type of locomotive to which it is fitted. It differs from the usual closed cycle condensing steam engine, in that the function of the condenser is primarily either to recover water, or to avoid excessive emissions to the atmosphere, rather than maintaining a vacuum to improve both efficiency and power.
The steam-electric power station is a power station in which the electric generator is steam driven. Water is heated, turns into steam and spins a steam turbine which drives an electrical generator. After it passes through the turbine, the steam is condensed in a condenser. The greatest variation in the design of steam-electric power plants is due to the different fuel sources.
Economizers, or economisers (UK), are mechanical devices intended to reduce energy consumption, or to perform useful function such as preheating a fluid. The term economizer is used for other purposes as well. Boiler, power plant, heating, refrigeration, ventilating, and air conditioning (HVAC) uses are discussed in this article. In simple terms, an economizer is a heat exchanger.
An evaporator is a device used to turn the liquid form of a chemical substance, such as water, into a vapor.
Taprogge GmbH is a medium-sized company based in Wetter, Germany. The company is named after founding brothers Ludwig and Josef Taprogge. Founded in 1953, the company is known for its tube cleaning systems for steam turbine condensers, heat exchangers and debris filters for water-cooled shell and tube heat exchangers and condensers.
Boiler feedwater is an essential part of boiler operations. The feed water is put into the steam drum from a feed pump. In the steam drum the feed water is then turned into steam from the heat. After the steam is used it is then dumped to the main condenser. From the condenser it is then pumped to the deaerated feed tank. From this tank it then goes back to the steam drum to complete its cycle. The feed water is never open to the atmosphere. This cycle is known as a closed system or Rankine cycle.
Vapor-compression desalination (VC) refers to a distillation process where the evaporation of sea or saline water is obtained by the application of heat delivered by compressed vapor.
The Chaplin's patent distilling apparatus with Steam pump for circulating water attached was an early design of an evaporator, a device for producing fresh water on board ship by distillation of seawater. An example of this apparatus has been recovered from the wreck of SS Xantho (1872), an auxiliary steamship used in Australia to transport passengers and trade goods before ultimately sinking in Port Gregory, Western Australia in 1872. It is purported that the Alexander Chaplin distiller from the Xantho wreck is the only known surviving example of a Chaplin distilling apparatus on board a vessel of this period.
Membrane distillation (MD) is a thermally driven separation process in which separation is driven by phase change. A hydrophobic membrane presents a barrier for the liquid phase, allowing the vapour phase to pass through the membrane's pores. The driving force of the process is a partial vapour pressure difference commonly triggered by a temperature difference.
The low-temperature distillation (LTD) technology is the first implementation of the direct spray distillation (DSD) process. The first large-scale units are now in operation for desalination. The process was first developed by scientists at the University of Applied Sciences in Switzerland, focusing on low-temperature distillation in vacuum conditions, from 2000 to 2005.
A distilling ship is a class of military ships, generally converted tankers, with the capability to convert salt water into fresh water. They were typically stationed at forward bases during conflict where they supported on-the-ground troops and front line naval units.
