Gasket (sailing)

Last updated
A gasket holding the main-royal on a modern square-rigged training ship. SlipperyHitchOnRoyalYard.jpg
A gasket holding the main-royal on a modern square-rigged training ship.

In sailing, gaskets are lengths of rope or fabric used for reefing a sail, or hold a stowed sail in place. In modern use, the term is usually restricted to square-rigged ships, the equivalent items on yachts being referred to by the more prosaic "sail ties".

On most ships, gaskets are made of rope. They are attached to the top of the yard and, left loose, would hang behind the sail. Gaskets should never be left dangling, however, so when the sail is set they are brought around underneath the yard and up the back of it and then tied to the jackstay (metal rod) where they originated. Alternatively, longer gaskets - particularly the clew gaskets described below - can be secured using a gasket coil. When the sail is to be stowed it is first folded and bagged neatly within itself, pulled onto the top of the yard, and then the gaskets are brought round over it and secured to the jackstay to hold it in place. Gaskets should be tied with a slippery hitch to enable them to be let off quickly, though if the yard is large there may only be enough rope to form a clove hitch when the gasket is brought round it.

Most ships are equipped with clew gaskets at the outer ends of the yards. These do not pass around the sail, but through a shackle or ring on the blocks of the sheet. Pulled tight and secured to the jackstay or the yard's lift, this takes the load off the clewline and sail, and should allow the blocks to be lifted higher, dragging the sail down less and enabling a neater stow.

Related Research Articles

<span class="mw-page-title-main">Bowline</span> Simple knot used to form a fixed loop at the end of a rope

The bowline is an ancient and simple knot used to form a fixed loop at the end of a rope. It has the virtues of being both easy to tie and untie; most notably, it is easy to untie after being subjected to a load. The bowline is sometimes referred to as king of the knots because of its importance. Along with the sheet bend and the clove hitch, the bowline is often considered one of the most essential knots.

A whipping knot or whipping is a binding of marline twine or whipcord around the end of a rope to prevent its natural tendency to fray.

<span class="mw-page-title-main">Traveller (nautical fitting)</span> Sliding part of a sailing vessel

A traveller is a part of the rigging of a boat or ship that provides a moving attachment point for a rope, sail or yard to a fixed part of the vessel. It may take the form of anything from a simple ring on a metal bar or a spar to, especially in a modern yacht, a more complex "car" – a component with bearing-mounted wheels running on a shaped aluminium extrusion.

<span class="mw-page-title-main">Running rigging</span> Lines that control sails

Running rigging is the rigging of a sailing vessel that is used for raising, lowering, shaping and controlling the sails on a sailing vessel—as opposed to the standing rigging, which supports the mast and bowsprit. Running rigging varies between vessels that are rigged fore and aft and those that are square-rigged.

<span class="mw-page-title-main">Cat's paw (knot)</span> Type of knot

The Cat's paw is a knot used for connecting a rope to an object. It is very similar to the cow hitch except there is an additional twist on each side of the bight, making it less prone to slipping.

The cat's-paw is the common hook hitch for slings. It is the same basic form as the bale sling hitch but has additional twists. Brady says "two or three altogether," and Steel, who mentioned the name in 1794, says "three twists." It is the best of all sling hitches and is often recommended for a slippery rope. But no hitch can slip when tied in a slings since it has no ends. All that is needed is a hitch that cannot jam, and this requirement the cat's-paw fills admirably. The knot spills instantly when removed from the hook. It is the hitch always used for heavy lifts.

<span class="mw-page-title-main">Stopper knot</span> Knot that forms a fixed thicker point to prevent unreeving

A stopper knot is a knot that creates a fixed thicker point on an otherwise-uniform thickness rope for the purpose of preventing the rope, at that point, from slipping through a narrow passage, such as a hole in a block. To pass a rope through a block, or hole, is to reeve it. To pull it out is to unreeve it. Stopper knots prevent the rope from unreeving on its own.

<span class="mw-page-title-main">Yard (sailing)</span> Sail-carrying part of the rigging of a sailing ship

A yard is a spar on a mast from which sails are set. It may be constructed of timber or steel or from more modern materials such as aluminium or carbon fibre. Although some types of fore and aft rigs have yards, the term is usually used to describe the horizontal spars used on square rigged sails. In addition, for some decades after square sails were generally dispensed with, some yards were retained for deploying wireless (radio) aerials and signal flags.

This glossary of nautical terms is an alphabetical listing of terms and expressions connected with ships, shipping, seamanship and navigation on water. Some remain current, while many date from the 17th to 19th centuries. The word nautical derives from the Latin nauticus, from Greek nautikos, from nautēs: "sailor", from naus: "ship".

<span class="mw-page-title-main">Sheet (sailing)</span> One of the lines on a sail ship

In sailing, a sheet is a line used to control the movable corner(s) (clews) of a sail.

<span class="mw-page-title-main">Buntline hitch</span> Type of knot

The buntline hitch is a knot used for attaching a rope to an object. It is formed by passing the working end around an object, then making a clove hitch around the rope's standing part and taking care that the turns of the clove hitch progress towards the object rather than away from it. Secure and easily tied, the buntline hitch will jam when subjected to extreme loads. Given the knot's propensity to jam, it is often made in slipped form.

The buntline hitch, when bent to a yard, makes a more secure knot than two half hitches, but is more liable to jam. It differs from two half hitches in that the second half hitch is inside instead of outside the first one.

<span class="mw-page-title-main">Boom (sailing)</span> In sailing, a spar along the bottom edge of a fore and aft rigged sail

In sailing, a boom is a spar (pole), along the foot of a fore and aft rigged sail, that greatly improves control of the angle and shape of the sail. The primary action of the boom is to keep the foot flatter when the sail angle is away from the centerline of the boat. The boom also serves as an attachment point for more sophisticated control lines. Because of the improved sail control it is rare to find a non-headsail without a boom, but lateen sails, for instance, are loose-footed. In some modern applications, the sail is rolled up into the boom for storage or reefing.

<span class="mw-page-title-main">Rolling hitch</span> Knot used to attach a rope to a rod, pole, or another rope

The rolling hitch is a knot used to attach a rope to a rod, pole, or another rope. A simple friction hitch, it is used for lengthwise pull along an object rather than at right angles. The rolling hitch is designed to resist lengthwise movement for only a single direction of pull.

<span class="mw-page-title-main">Slippery hitch</span> Knot

A slippery hitch is a knot used to attach a line to a rod or bar. It does not provide great strength compared to some other knots, but it can be tied relatively quickly and released very easily. These characteristics mean that it is used on square-rigged ships for securing the gaskets that bind stowed sails to the yards.

<span class="mw-page-title-main">Footrope</span>

Each yard on a square or gaff rigged sailing ship is equipped with a footrope for sailors to stand on while setting or stowing the sails.

<span class="mw-page-title-main">Tack (square sail)</span>

The tack of a square-rigged sail is a line attached to its lower corner. This is in contrast to the more common fore-and-aft sail, whose tack is a part of the sail itself, the corner which is secured to the vessel.

<span class="mw-page-title-main">Clewlines and buntlines</span> Ropes used to handle sails of a ship

Clewlines and buntlines are lines used to handle the sails of a square rigged ship.

<span class="mw-page-title-main">Halter hitch</span> Type of knot

The halter hitch is a type of knot used to connect a rope to an object. As the name implies, an animal's lead rope, attached to its halter, may be tied to a post or hitching rail with this knot. The benefit of the halter hitch is that it can be easily released by pulling on one end of the rope, even if it is under tension. Some sources show the knot being finished with the free end running through the slipped loop to prevent it from working loose or being untied by a clever animal, still allowing easy but not instant untying.

<span class="mw-page-title-main">Cleat (nautical)</span> Rope-securing device

In nautical contexts, a cleat is a device for securing a rope.

<span class="mw-page-title-main">Jackstay</span> Substantial line between two points used to guide or support.

A jackstay is a cable or bar between two points to support and guide a load between those points, or as an anchor to attach something to be constrained along that line. The term is mostly used in a marine context and originated on sailing ships. Note the use of "stay" implies load bearing working rigging. In diving it is also a line to guide the movements of a diver between the endpoints.

References