Lateen

Last updated
The lateen sail Rigging-lateen-sail.svg
The lateen sail

A lateen (from French latine, meaning "Latin" [1] ) or latin-rig is a triangular sail set on a long yard mounted at an angle on the mast, and running in a fore-and-aft direction. The settee can be considered to be an associated type of the same overall category of sail. [2]

Contents

The lateen originated in the Mediterranean as early as the 2nd century AD, during Roman times, and became common there by the 5th century. The wider introduction of lateen rig at this time coincided with a reduction in the use of the Mediterranean square rig of the classical era. Since the performance of these two rigs is broadly similar, it is suggested that the change from one to the other was on cost grounds, since lateen rigs used fewer components and had less cordage to be replaced when it wore out. [2]

Arab seafarers adopted the lateen rig at a later date there is some limited archaeological evidence of lateen rig in the Indian Ocean in the 13th century AD and iconographic evidence from the 16th century. [2] It has been suggested that this Arab use of lateen transferred to Austronesian maritime technology in the Far East, giving rise to the various fore-and-aft rigs used in that region, such as the crab claw sail. [3]

The lateen sail played a prominent part in the shifts in maritime technology that occurred as Mediterranean and Northern European ship-construction traditions merged in the 16th century, with the lateen mizzen being, for a time, universally used in the full-rigged ships of the time though later supplanted by gaff rig in this role. [2]

History

Mediterranean origin

The lateen was developed in the Mediterranean as early as the 2nd century AD, during Roman times. It became common by the 5th century. [2]

Byzantine ship rigged with settee sail (miniature from c. 880) Meister der Predigten des Heiligen Gregor von Nazianz 001.jpg
Byzantine ship rigged with settee sail (miniature from c. 880)

The lateen also exists as a subtype: the settee. Instead of being a triangular sail, this has a short vertical luff having the appearance of a triangular lateen with the front corner cut off. Both types of lateen were likely used from an early date on: a 2nd-century AD gravestone depicts a quadrilateral lateen sail (also known as a settee), while a 4th-century mosaic shows a triangular one, which was to become the standard rig throughout the Middle Ages. [5] The earliest archaeologically excavated ship that has been reconstructed with a lateen rig is dated to ca. 400 AD ( Yassi Ada II ), with a further four being attested prior to the Arab advance to the Mediterranean. [6] The Kelenderis ship mosaic (late 5th to early 6th century) [7] [8] and the Kellia ship graffito from the early 7th century complement the picture. [8]

By the 6th century, the lateen sail had largely replaced the square sail throughout the Mediterranean, the latter almost disappearing from Mediterranean iconography until the mid-13th century. [9] It became the standard rig of the Byzantine dromon war galley and was probably also employed by Belisarius' flagship in the 532 AD invasion of the Vandal Kingdom. [10] [11] The fully triangular lateen and the settee continued to coexist in the middle Byzantine period, as evidenced by Christian iconography, [4] as well as a recent find of a graffito in the Yenikapı excavations. [12] In the 12th to 13th centuries the rigging underwent a change when the hook-shaped masthead made way for an arrangement more akin to a barrel-like crow's nest. [13]

After the Muslim conquests, the Arabs adopted the lateen sail by way of the Coptic populace, which shared the existing Mediterranean maritime tradition and continued to provide the bulk of galley crews for Muslim-led fleets for centuries to come. [14] This is also indicated by the terminology of the lateen among Mediterranean Arabs which is derived from Greco-Roman nomenclature. [15] More detailed research into their early use of the lateen is hampered by a distinct lack of unequivocal depictions of sailing rigs in early Islamic art. [16] [16] A glazed pottery dish from Saracenic Dénia dating to the 11th century is at present the earliest securely identifiable example found in the Mediterranean. [16]

Nile River

From the Mediterranean, the lateen sail spread to the Nile River in Egypt, where the lateen-rigged felucca was developed. [17]

Diffusion to Indian Ocean

Dhow with lateen sail in "bad tack" with the sail pressing against the mast, in Mozambique. Inhambane-dhow.JPG
Dhow with lateen sail in "bad tack" with the sail pressing against the mast, in Mozambique.

The emergence of new evidence for the development and spread of the lateen sail in the ancient Mediterranean in recent decades has led to a reevaluation of the role of Arab seafaring in the Indian Ocean, replacing a belief that this sail has an eastern origin. [18] [19]

A large dhow with two settee sail rigs and a headsail. Sd11-boom.JPG
A large dhow with two settee sail rigs and a headsail.

Until about 1500, square rig predominated in the Indian Ocean.This then changed rapidly, with nearly all vessels now being lateen rigged. [20] As Mediterranean hull design and construction methods are known to have been subsequently adopted by Eastern Muslim shipbuilders, it is assumed that this process also included the lateen rigging of the novel caravel.

Later development

The Bracera: a traditional lateen-rigged sailboat of the Mediterranean. Bracera traditional sailboat Croatia.jpg
The Bracera: a traditional lateen-rigged sailboat of the Mediterranean.
A 17th-century woodcut of a triangular-sailed Bermudian vessel. Its raked masts were a development of the lateen. Bermuda rig - 17th Century woodcut.jpg
A 17th-century woodcut of a triangular-sailed Bermudian vessel. Its raked masts were a development of the lateen.

Until the 14th century, the lateen sail was employed primarily on the Mediterranean Sea, while the Atlantic and Baltic (and Indian Ocean) vessels relied on square sails. The Northern European adoption of the lateen in the Late Middle Ages was a specialized sail that was one of the technological developments in shipbuilding that made ships more maneuverable, thus, in the historian's traditional progression, permitting merchants to sail out of the Mediterranean and into the Atlantic Ocean; caravels typically mounted three or more lateens. However, the great size of the lateen yardarm makes it difficult and dangerous to handle on larger ships in stormy weather, and with the development of the carrack, the lateen was restricted to the mizzen mast. In the early nineteenth century, the lateen was replaced in European ships by the driver or spanker.

The lateen survived as a rigging choice for mainsails of small craft where local conditions were favorable. For instance, barge-like vessels in the American maritimes north of Boston, called gundalows, carried lateen rigs throughout the late nineteenth and early twentieth centuries. Likewise, lateen sail survived in the Baltic until the late 19th century. Because the yard pivots on its point of attachment to the mast, the entire sail and yard can be swiftly dropped. This was an advantage when navigating the tidal riverways of the region, which often required passage under bridges. The balancelle, a Mediterranean coasting and fishing boat of the 19th century, also used a single lateen sail.

The bad tack

One of the disadvantages of the lateen in the modern form described below is the fact that one of its tacks is significantly less advantageous than the other, the "bad tack". Because the sail sits to the side of the mast, on one tack, the mast pushes directly against the sail on the leeward side, where it can significantly interfere with the airflow over the sail. This is the bad tack. On the other tack the sail is pushed away from the mast, greatly reducing the interference. On modern lateens, with their typically shallower angles, this tends to disrupt the airflow over a larger area of the sail, affecting speed.[ citation needed ]

However, there are forms of the lateen rig, as in vela latina canaria, where the spar is changed from one side to the other when tacking. This way the rig doesn't suffer these airflow disruptions that come from the sail pushed against the mast. [21]

The lateen sail can also be tacked by loosening the yard upper brace, tightening the lower brace until the yard is in vertical position, and twisting the yard on the other side of the mast by a tack. Another way of tacking with a lateen sail is to loosen the braces, lift the yard vertical, detach the sheet and tack, and turn the sail on the other side of the mast in front of the mast, and reattach the sheet and tack. This method is described in Björn Landström's The Ship.[ citation needed ]

The lateen rig was also the ancestor of the Bermuda rig, by way of the Dutch bezaan rig. In the 16th century, when Spain ruled the Netherlands, the lateen rigs were introduced to Dutch boat builders, who soon modified the design by omitting the mast and fastening the lower end of the yard directly to the deck, the yard becoming a raked mast with a full-length, triangular (leg-of-mutton) mainsail aft. Introduced to Bermuda early in the 17th century, this developed into the Bermuda rig, which, in the 20th century, was adopted almost universally for small sailing vessels.[ citation needed ]

Lateen replacement of square rig

It is a widespread misconception that the lateen rig replaced square rig because of better windward performance and greater manoeuvrability. A study of the relative effectiveness of the two shows that their performance was actually very similar. These results apply both when working to windward and when sailing downwind. (Furthermore, differences in performance are derived as much from the hull shape as the type of rig.) It is concluded that there was no evolutionary technological development that gave improved sailing performance in the 5th century AD change from the Mediterranean square rig to lateen, and that factors other than windward performance must have dictated this change. [22]

The Mediterranean Square Rig underwent a simplification in the 5th century AD, with reduction in the number of components. Most obviously, in the archaeological context, this included the absence of brails (and the distinctive lead rings through which these ropes were led). This change is suggested to be on cost grounds, both reducing the expense of a new build and of ongoing maintenance. This would have given some degradation of performance of this type of square rig. Lateen was already available as an alternative and, having fewer component parts, could compete on cost but maintained the performance of the original Mediterranean Square Rig. This coincided with innovation in hull construction methods as the edge-to-edge joining of the hull planking with pegged tenons (a "shell first" construction technique) started to be replaced with the early evolutionary phases of "frame first" carvel construction. This is also suggested to be driven by costs. Therefore the change from square rig to lateen in the 5th century is considered to be driven by construction and maintenance costs, not by any significant difference in sailing performance. [23]

See also

Citations

  1. "the definition of lateen". Dictionary.com. Retrieved 3 April 2018.
  2. 1 2 3 4 5 Whitewright 2012a.
  3. Anderson 2018.
  4. 1 2 Whitewright 2009, p. 100.
  5. Casson 1995 , pp. 243–245
  6. Castro et al. 2008 , p. 352
  7. Pomey 2006.
  8. 1 2 Whitewright 2009, p. 98f.
  9. Castro et al. 2008 , p. 2
  10. Basch 2001 , p. 63
  11. Casson 1995 , p. 245, fn. 82
  12. Günsenin & Rieth 2012 , p. 157
  13. Whitewright 2009 , p. 101
  14. Campbell 1995 , pp. 9–10
  15. White 1978 , pp. 256f.
  16. 1 2 3 Whitewright 2012b, p. 589.
  17. Bisson, Wilfred J. (2020). "Introduction: Travel Technology". In Burns, William E. (ed.). Science and Technology in World History, Volume 1. ABC-CLIO. p. 226. ISBN   978-1-440-87116-0.
  18. Whitewright 2009, p. 98.
  19. Casson 1954, pp. 214f..
  20. White 1978, p. 258.
  21. "YouTube". www.youtube.com. Retrieved 3 April 2018.[ dead YouTube link ]
  22. Whitewright 2011.
  23. Whitewright, Julian (April 2012). "Technological Continuity and Change: The Lateen Sail of the Medieval Mediterranean". Al-Masāq. 24 (1): 1–19. doi:10.1080/09503110.2012.655580. S2CID   161464823.

General and cited sources

Further reading

Related Research Articles

<span class="mw-page-title-main">Sailing ship</span> Large wind-powered water vessel

A sailing ship is a sea-going vessel that uses sails mounted on masts to harness the power of wind and propel the vessel. There is a variety of sail plans that propel sailing ships, employing square-rigged or fore-and-aft sails. Some ships carry square sails on each mast—the brig and full-rigged ship, said to be "ship-rigged" when there are three or more masts. Others carry only fore-and-aft sails on each mast, for instance some schooners. Still others employ a combination of square and fore-and-aft sails, including the barque, barquentine, and brigantine.

<span class="mw-page-title-main">Rig (sailing)</span> Arrangement of a ships masts, sails, and ropes

A sailing vessel's rig is its arrangement of masts, sails and rigging. Examples include a schooner rig, cutter rig, junk rig, etc. A rig may be broadly categorized as "fore-and-aft", "square", or a combination of both. Within the fore-and-aft category there is a variety of triangular and quadrilateral sail shapes. Spars or battens may be used to help shape a given kind of sail. Each rig may be described with a sail plan—formally, a drawing of a vessel, viewed from the side.

A jib is a triangular sail that sets ahead of the foremast of a sailing vessel. Its forward corner (tack) is fixed to the bowsprit, to the bows, or to the deck between the bowsprit and the foremost mast. Jibs and spinnakers are the two main types of headsails on a modern boat.

<span class="mw-page-title-main">Carvel (boat building)</span> Method of building a boat

Carvel built or carvel planking is a method of boat building in which hull planks are laid edge to edge and fastened to a robust frame, thereby forming a smooth surface. Traditionally the planks are neither attached to, nor slotted into, each other, having only a caulking sealant between the planks to keep water out. Modern carvel builders may attach the planks to each other with glues and fixings. It is a "frame first" method of hull construction, where the shape is determined by the framework onto which the planks are fixed. This is in contrast to "plank first" or "shell first" methods, where the outer skin of the hull is made and then reinforced by the insertion of timbers that are fitted to that shape. The most common modern "plank first" method is clinker construction; in the classical period "plank first" involved joining the edges of planks with mortise and tenon joints within the thickness of the timbers, superficially giving the smooth-hull appearance of carvel construction, but achieved by entirely different means.

<span class="mw-page-title-main">Running rigging</span> Lines that control sails

Running rigging is the rigging of a sailing vessel that is used for raising, lowering, shaping and controlling the sails on a sailing vessel—as opposed to the standing rigging, which supports the mast and bowsprit. Running rigging varies between vessels that are rigged fore and aft and those that are square-rigged.

<span class="mw-page-title-main">Mast (sailing)</span> Pole used in rigging of a sailing vessel

The mast of a sailing vessel is a tall spar, or arrangement of spars, erected more or less vertically on the centre-line of a ship or boat. Its purposes include carrying sails, spars, and derricks, giving necessary height to a navigation light, look-out position, signal yard, control position, radio aerial or signal lamp. Large ships have several masts, with the size and configuration depending on the style of ship. Nearly all sailing masts are guyed.

<span class="mw-page-title-main">Bermuda rig</span> Configuration of mast and rigging for a type of sailboat

A Bermuda rig, Bermudian rig, or Marconi rig is a configuration of mast and rigging for a type of sailboat and is the typical configuration for most modern sailboats. This configuration was developed in Bermuda in the 17th century; the term Marconi, a reference to the inventor of the radio, Guglielmo Marconi, became associated with this configuration in the early 20th century, because the wires that stabilize the mast of a Bermuda rig reminded observers of the wires on early radio masts.

<span class="mw-page-title-main">Full-rigged ship</span> Sailing vessel with three or more square-rigged masts

A full-rigged ship or fully rigged ship is a sailing vessel with a sail plan of three or more masts, all of them square-rigged. Such a vessel is said to have a ship rig or be ship-rigged, with each mast stepped in three segments: lower, top, and topgallant.

<span class="mw-page-title-main">Fore-and-aft rig</span> Sailing rig consisting mainly of sails

A fore-and-aft rig is a sailing vessel rig with sails set mainly along the line of the keel, rather than perpendicular to it as on a square rigged vessel.

<span class="mw-page-title-main">Tacking (sailing)</span> A sailing maneuver

Tacking or coming about is a sailing maneuver by which a sailing craft, whose next destination is into the wind, turns its bow toward and through the wind so that the direction from which the wind blows changes from one side of the boat to the other, allowing progress in the desired direction. Sailing vessels are unable to sail higher than a certain angle towards the wind, so "beating to windward" in a zig-zag fashion with a series of tacking maneuvers, allows a vessel to sail towards a destination that is closer to the wind than the vessel can sail directly.

<span class="mw-page-title-main">Dromon</span> Type of warship of the Byzantine navy

A dromon was a type of galley and the most important warship of the Byzantine navy from the 5th to 12th centuries AD, when they were succeeded by Italian-style galleys. It was developed from the ancient liburnian, which was the mainstay of the Roman navy during the Empire.

<span class="mw-page-title-main">Polacca</span> Type of ship used in the 17th–19th centuries

A polacca is a type of seventeenth- to nineteenth-century sailing vessel, similar to the xebec. The name is the feminine of "Polish" in the Italian language. The polacca was frequently seen in the Mediterranean. It had two or three single-pole masts, the three-masted vessels often with a lateen hoisted on the foremast and a gaff or lateen on the mizzen mast. The mainmast was square-rigged after the European style. Special polaccas were used by Murat Reis, whose ships had lateen sails in front and fore-and-aft rig behind.

<span class="mw-page-title-main">Spritsail</span>

The spritsail is a four-sided, fore-and-aft sail that is supported at its highest points by the mast and a diagonally running spar known as the sprit. The foot of the sail can be stretched by a boom or held loose-footed just by its sheets. A spritsail has four corners: the throat, peak, clew, and tack. The Spritsail can also be used to describe a rig that uses a spritsail.

<span class="mw-page-title-main">Foresail</span> Type of sail

A foresail is one of a few different types of sail set on the foremost mast (foremast) of a sailing vessel:

<span class="mw-page-title-main">Crab claw sail</span> Triangular sail with spars along upper and lower edges used by traditional Austronesians

The crab claw sail is a fore-and-aft triangular sail with spars along upper and lower edges. The crab claw sail was first developed by the Austronesian peoples by at least 2000 BCE. It is used in many traditional Austronesian cultures in Island Southeast Asia, Micronesia, Island Melanesia, Polynesia, and Madagascar. It is sometimes known as the Oceanic lateen or the Oceanic sprit, even though it is not restricted to Oceania, is neither a lateen sail nor a spritsail, and has an independent older origin.

The settee sail was a lateen sail with the front corner cut off, giving it a quadrilateral shape. The settee sail requires a shorter yard than does the lateen, and both settee and lateen have shorter masts than square-rigged sails.

<span class="mw-page-title-main">Bracera</span> Traditional Croatian sailing vessel

A bracera or brazzera is a traditional Adriatic coastal cargo sailing vessel originated in Dalmatia and first recorded in the 16th-century chronicles. Along with its larger sisters - trabakuls and peligs, braceras formed the backbone of the commercial fleet on the Adriatic Sea with one masted one being the most prominent and best known. This solid and very mobile boat with wide hips and blunt bow was particularly suitable for commerce and communication between the many islands of the Adriatic as well as neighboring coasts. Already in the 19th century over 800 of them were listed in the Austro-Hungarian fleet register covering vessels of the Dalmatian and Istrian coasts. Adriatic braceras distinguish from the vessels carrying same/similar names like, for example, in the Aegean Sea. Unlike there, on the Adriatic the term refers to the entire boat, the system that consists of the hull and the rig as well, and not merely the sail.

<span class="mw-page-title-main">Sail</span> Fabric or other surface supported by a mast to allow wind propulsion

A sail is a tensile structure, which is made from fabric or other membrane materials, that uses wind power to propel sailing craft, including sailing ships, sailboats, windsurfers, ice boats, and even sail-powered land vehicles. Sails may be made from a combination of woven materials—including canvas or polyester cloth, laminated membranes or bonded filaments, usually in a three- or four-sided shape.

<span class="mw-page-title-main">Tanja sail</span> Oblique quadrilateral sail from south east Asia

Tanja sail or tanja rig is a type of sail commonly used by the Austronesian people, particularly in Maritime Southeast Asia. It is also known as the tilted square sail, canted rectangular sail, rectangular balance lug, or balance lug sail in English. In historical sources, a tanja sail is sometimes incorrectly referred to as a lateen sail or simply square sail.