Hata model

Last updated

The Hata model is a radio propagation model for predicting the path loss of cellular transmissions in exterior environments, valid for microwave frequencies from 150 to 1500 MHz. It is an empirical formulation based on the data from the Okumura model, and is thus also commonly referred to as the Okumura–Hata model. [1] The model incorporates the graphical information from Okumura model and develops it further to realize the effects of diffraction, reflection and scattering caused by city structures. [2] Additionally, the Hata Model applies corrections for applications in suburban and rural environments. [1] [2]

Contents

Model description

Though based on the Okumura model, the Hata model does not provide coverage to the whole range of frequencies covered by Okumura model. Hata model does not go beyond 1500 MHz while Okumura provides support for up to 1920 MHz. The model is suited for both point-to-point and broadcast communications, and covers mobile station antenna heights of 1–10 m, base station antenna heights of 30–200 m, and link distances from 1–10 km.

Urban environments

The Hata model for urban environments is the basic formulation since it was based on Okumura's measurements made in the built-up areas of Tokyo. It is formulated as following:

For small or medium-sized city,

and for large cities,

where

LU = Path loss in urban areas. Unit: decibel (dB)
hB = Height of base station antenna. Unit: meter (m)
hM = Height of mobile station antenna. Unit: meter (m)
f = Frequency of transmission. Unit: Megahertz (MHz)
CH = Antenna height correction factor
d = Distance between the base and mobile stations. Unit: kilometer (km).

Suburban environments

The Hata model for suburban environments is applicable to the transmissions just out of the cities and on rural areas where man-made structures are there but not so high and dense as in the cities. To be more precise, this model is suitable where buildings exist, but the mobile station does not have a significant variation of its height. It is formulated as:

where

LSU = Path loss in suburban areas. Unit: decibel (dB)
LU = Path loss from the small city version of the model (above). Unit: decibel (dB)
f = Frequency of transmission. Unit: Megahertz (MHz).

Open environments

The Hata model for rural environments is applicable to the transmissions in open areas where no obstructions block the transmission link. It is formulated as:

where

LO = Path loss in open areas. Unit: decibel (dB)
LU = Average path loss from the small city version of the model (above). Unit: decibel (dB)
f = Frequency of transmission. Unit: megahertz (MHz).

Derivative models

There are more specific models for special uses. For example the COST Hata model, an urban HataModel, was developed by the European Cooperation in Science and Technology. [3] In turn, the ITU-R P.1546 model is an enhancement to the COST-231 Model.

PCS is another extension of the Hata model. The Walfisch and Bertoni model is further advanced.

Related Research Articles

The decibel is a relative unit of measurement equal to one tenth of a bel (B). It expresses the ratio of two values of a power or root-power quantity on a logarithmic scale. Two signals whose levels differ by one decibel have a power ratio of 101/10 or root-power ratio of 101/20.

In telecommunication, the free-space path loss (FSPL) is the attenuation of radio energy between the feedpoints of two antennas that results from the combination of the receiving antenna's capture area plus the obstacle-free, line-of-sight (LoS) path through free space. The "Standard Definitions of Terms for Antennas", IEEE Std 145-1993, defines free-space loss as "The loss between two isotropic radiators in free space, expressed as a power ratio." It does not include any power loss in the antennas themselves due to imperfections such as resistance. Free-space loss increases with the square of distance between the antennas because the radio waves spread out by the inverse square law and decreases with the square of the wavelength of the radio waves. The FSPL is rarely used standalone, but rather as a part of the Friis transmission formula, which includes the gain of antennas. It is a factor that must be included in the power link budget of a radio communication system, to ensure that sufficient radio power reaches the receiver such that the transmitted signal is received intelligibly.

Path loss, or path attenuation, is the reduction in power density (attenuation) of an electromagnetic wave as it propagates through space. Path loss is a major component in the analysis and design of the link budget of a telecommunication system.

<span class="mw-page-title-main">Gain (antenna)</span> Telecommunications performance metric

In electromagnetics, an antenna's gain is a key performance parameter which combines the antenna's directivity and radiation efficiency. The term power gain has been deprecated by IEEE. In a transmitting antenna, the gain describes how well the antenna converts input power into radio waves headed in a specified direction. In a receiving antenna, the gain describes how well the antenna converts radio waves arriving from a specified direction into electrical power. When no direction is specified, gain is understood to refer to the peak value of the gain, the gain in the direction of the antenna's main lobe. A plot of the gain as a function of direction is called the antenna pattern or radiation pattern. It is not to be confused with directivity, which does not take an antenna's radiation efficiency into account.

<span class="mw-page-title-main">Effective radiated power</span> Definition of directional radio frequency power

Effective radiated power (ERP), synonymous with equivalent radiated power, is an IEEE standardized definition of directional radio frequency (RF) power, such as that emitted by a radio transmitter. It is the total power in watts that would have to be radiated by a half-wave dipole antenna to give the same radiation intensity as the actual source antenna at a distant receiver located in the direction of the antenna's strongest beam. ERP measures the combination of the power emitted by the transmitter and the ability of the antenna to direct that power in a given direction. It is equal to the input power to the antenna multiplied by the gain of the antenna. It is used in electronics and telecommunications, particularly in broadcasting to quantify the apparent power of a broadcasting station experienced by listeners in its reception area.

In telecommunications, particularly in radio frequency engineering, signal strength refers to the transmitter power output as received by a reference antenna at a distance from the transmitting antenna. High-powered transmissions, such as those used in broadcasting, are expressed in dB-millivolts per metre (dBmV/m). For very low-power systems, such as mobile phones, signal strength is usually expressed in dB-microvolts per metre (dBμV/m) or in decibels above a reference level of one milliwatt (dBm). In broadcasting terminology, 1 mV/m is 1000 μV/m or 60 dBμ.

A link budget is an accounting of all of the power gains and losses that a communication signal experiences in a telecommunication system; from a transmitter, through a communication medium such as radio waves, cable, waveguide, or optical fiber, to the receiver. It is an equation giving the received power from the transmitter power, after the attenuation of the transmitted signal due to propagation, as well as the antenna gains and feedline and other losses, and amplification of the signal in the receiver or any repeaters it passes through. A link budget is a design aid, calculated during the design of a communication system to determine the received power, to ensure that the information is received intelligibly with an adequate signal-to-noise ratio. Randomly varying channel gains such as fading are taken into account by adding some margin depending on the anticipated severity of its effects. The amount of margin required can be reduced by the use of mitigating techniques such as antenna diversity or multiple-input and multiple-output (MIMO).

Weissberger’s modified exponential decay model, or simply, Weissberger’s model, is a radio wave propagation model that estimates the path loss due to the presence of one or more trees in a point-to-point telecommunication link. This model belongs to the category Foliage or Vegetation models.

The ITU vegetation model is a radio propagation model that estimates the path loss encountered due to the presence of one or more trees inside a point to point telecommunication link. The predictions found from this model is congruent to those found from Weissberger’s modified exponential decay model in low frequencies.

The Egli model is a terrain model for radio frequency propagation. This model, which was first introduced by John Egli in his 1957 paper, was derived from real-world data on UHF and VHF television transmissions in several large cities. It predicts the total path loss for a point-to-point link. Typically used for outdoor line-of-sight transmission, this model provides the path loss as a single quantity.

The COST Hata model is a radio propagation model that extends the urban Hata model to cover a more elaborated range of frequencies. It is the most often cited of the COST 231 models, also called the Hata Model PCS Extension. This model is the combination of empirical and deterministic models for estimating path loss in an urban area over frequency range of 800 MHz to 2000 MHz.

Young model is a radio propagation model that was built on the data collected on New York City. It typically models the behaviour of cellular communication systems in large cities.

The Lee model for area-to-area mode is a radio propagation model that operates around 900 MHz. Built as two different modes, this model includes an adjustment factor that can be adjusted to make the model more flexible to different regions of propagation.

The Okumura model is a radio propagation model that was built using the data collected in the city of Tokyo, Japan. The model is ideal for using in cities with many urban structures but not many tall blocking structures. The model served as a base for the Hata model.

The Lee model for point-to-point mode is a radio propagation model that operates around 900 MHz. Built as two different modes, this model includes an adjustment factor that can be adjusted to make the model more flexible to different regions of propagation.

The ITU indoor propagation model, also known as ITU model for indoor attenuation, is a radio propagation model that estimates the path loss inside a room or a closed area inside a building delimited by walls of any form. Suitable for appliances designed for indoor use, this model approximates the total path loss an indoor link may experience.

The log-distance path loss model is a radio propagation model that predicts the path loss a signal encounters inside a building or densely populated areas over distance.

This is an index to articles about terms used in discussion of radio propagation.

Downlink CNR is an important figure in system TVRO design. Below are certain parameters used in CNR computation.

<span class="mw-page-title-main">Two-ray ground-reflection model</span>

The two-rays ground-reflection model is a multipath radio propagation model which predicts the path losses between a transmitting antenna and a receiving antenna when they are in line of sight (LOS). Generally, the two antenna each have different height. The received signal having two components, the LOS component and the reflection component formed predominantly by a single ground reflected wave.

References

  1. 1 2 Rappaport, Theodore S. (2002). Wireless Communications: Principles and Practice (Second ed.). Prentice Hall. p.  153-154. ISBN   0-13-042232-0.
  2. 1 2 Seybold, John S. (2005). Introduction to RF propagation. John Wiley and Sons. ISBN   0-471-65596-1.
  3. Final report for COST Action 231, Chapter 4

Further reading