 | |
| Carries | Pedestrians, automobiles, trucks, light rail, heavy rail |
|---|---|
| Span range | Short to medium |
| Material | Timber, iron, steel |
| Movable | No |
| Design effort | Low |
| Falsework required | Yes |
A Howe truss is a truss bridge consisting of chords, verticals, and diagonals whose vertical members are in tension and whose diagonal members are in compression. The Howe truss was invented by William Howe in 1840, and was widely used as a bridge in the mid to late 1800s.
The earliest bridges in North America were made of wood, which was abundant and cheaper than stone or masonry. Early wooden bridges were usually of the Towne lattice truss or Burr truss design. Some later bridges were McCallum trusses (a modification of the Burr truss). About 1840, iron rods were added to wooden bridges. The Pratt truss used wooden vertical members in compression with diagonal iron braces. The Howe truss used iron vertical rods in tension with wooden diagonal braces. Both trusses used counter-bracing, which was becoming essential now that heavy railroad trains were using bridges. [1]
In 1830, Stephen Harriman Long received a patent for an all-wood parallel chord truss bridge. Long's bridge contained diagonal braces which were prestressed with wedges. The Long truss did not require a connection between the diagonal and the truss, and was able to remain in compression even when the wood shrank somewhat. [2]
William Howe was a construction contractor in Massachusetts when he patented the Howe truss design in 1840. [3] That same year, he established the Howe Bridge Works to build bridges using his design. [4] The first Howe truss ever built was a single-lane, 75-foot (23 m) long bridge in Connecticut carrying a road. [1] The second was a railroad bridge over the Connecticut River in Springfield, Massachusetts. This bridge, which drew extensive praise and attention, [3] had seven spans and was 180 feet (55 m) in length. [1] Both bridges were erected in 1840. [3] [1] One of Howe's workmen, Amasa Stone, purchased for $40,000 [5] ($1,220,800 in 2023 dollars) in 1842 the rights to Howe's patented bridge design. With his financial backer, Azariah Boody, Stone formed the bridge-building firm of Boody, Stone & Co., [6] which erected a large number of Howe truss bridges throughout New England. [5] Howe made additional improvements to his bridge, and patented a second Howe truss design in 1846. [7]
The Howe truss bridge consists of an upper and lower "chord", [a] each chord consisting of two parallel beams and each chord parallel to one another. The web [b] consists of verticals, braces, and counter-braces. Vertical posts connect the upper and lower chords to one another, and create "panels". A diagonal brace in each panel strengthens the bridge, and a diagonal counter-brace in each panel enhances this strength. [10] Howe truss bridges may be all wood, a combination of wood and iron, or all iron. [11] Whichever design is used, wooden timbers should have square ends without mortise and tenons. [12] The design of an all-metal Howe truss follows that of the wooden truss. [1]
The parallels in each chord are usually built up out of smaller beams, each small beam fastened to one another to create a continuous beam. [13] In wooden Howe trusses, these slender beams are usually no more than 10 to 15 inches (250 to 380 mm) wide and 6 to 8 inches (150 to 200 mm) deep. [1] In iron trusses, the upper chord beams are the same length as the panel. Upper chord beams are usually made of cast iron, while the lower chord beams are of wrought iron. [1] A minimum of three small beams are used, [14] each uniform in width and depth. [13] Fishplates are usually used to splice beams together. [14] (Lower chord beams may have eyes on each end, in which case they are fastened together with bolts, pins, or rivets.) [1] In wooden trusses, cotters and iron bolts are used every 4 feet (1.2 m) to connect the beams of the upper chord to one another. [1] [c] In the lower chord of a wooden bridge, clamps are used to couple beams together. [1]
Although generally of the same length, [12] beams are positioned so that a splice (the point where the end of two beams meet) is near the point where two panels meet [14] but not adjacent to the splice in an adjacent pair of beams. [13] [14]
The individual small beams which make up a parallel in a chord are separated along their long side by a space equal to the diameter of the vertical posts, [13] usually about 1 inch (25 mm). [1] This allows the vertical posts to pass through the parallel in the chord. [13] Batten plates [d] are placed diagonally between the members of a chord, and nailed in place to reduce bending and to act as a shim to provide ventilation between chord members. [16]
The middle third of the lower chord is always reinforced by one or more beams bolted to the chord. This reinforcement is generally one-sixth the width of the cross-section of the lower chord. [17] If a wood chord needs to be strengthened even more, additional slender beams may be bolted to the middle third of the each side of the lower chord. [12] When construction is complete, the upper chord of a Howe truss bridge will be in compression, while the lower chord is in tension. [13]
Vertical posts connect the upper and lower chords, and divide the truss into panels. [13] The Howe truss usually uses iron or steel verticals. [18] These are straight and round, [1] slightly reduced in circumference at the ends, and a screw thread added. [18] The vertical usually passes through the center of the angle block [1] and then through space left in the upper and lower chord. [14] A nut is used to secure the vertical post to the chord. Special plates or washers of wood or metal are used to help distribute the stress induced by the vertical post onto the chords. [18] [1] [e] Vertical posts are in tension, [13] which is induced by tightening the nuts on the vertical bars. [19]
Braces are diagonal beams which connect the bottom of a vertical post to the top of the next vertical post. [13] They are placed in the same plane as the chord. [14] Unlike iron or steel braces which are built up, wooden braces are cut to length. [1] Where the parallel in a chord has a thickness of X number of beams, each brace should have a thickness of X minus 1 beams. [13] [f] The depth-to-width ratio of each member of a diagonal brace should be no greater than that of the brace as a whole. [16] Braces may be a single piece, or several pieces spliced together with fishplate. [14] Braces are in compression [13] due to the tightening of the nuts on the verticals. [19] [2]
Counter-braces are diagonal beams which connect the bottom of a vertical post to the top of the next vertical post, and run roughly perpendicular to braces. [13] They are placed in the same plane as the chord, [14] are generally uniform in size, [17] and should have a thickness one beam less than a brace. [13] Unlike braces, counter-braces are a single piece. [14] Generally speaking, a bridge of six panels or less (about 75 feet (23 m) long) needs no counter-bracing. An eight-panel truss requires counter-braces in every panel but the end panels, and these should be at least one-fourth as strong as the braces. A 10-panel truss requires counter-braces in every panel but the end panels, and these should be at least one-half as strong as the braces. A Howe truss bridge can be strengthened to achieve a live load to dead load ratio of 2-to-1. If this ratio is 2-to-1 or greater, then a six-panel truss must have counter-braces and these must at least one-third as strong as the braces. The counter-braces in an eight-panel truss must be at least two-thirds as strong as the braces, and the counter-braces in a 10-panel truss must be at least equal in strength to the braces. [12] If rapidly moving live loads of any ratio are expected on the Howe truss, the counter-braces used in the center panel should be equal in strength to the braces, and the panel next to the end panel should have counter-braces at least one-half as strong as the braces. [17]
Where diagonal braces and counter-braces meet, they are usually bolted together. [14]
Braces and counter-braces are held in place with angle blocks. [13] Angle blocks are triangular in cross-section [13] and should be the same height [13] and width as the parallel of the chord. [1] Angle blocks may be made of wood or iron, [13] although iron is usually used for permanent structures. [12] Angle blocks are attached upside down to the upper chord, and right side up to the lower chord. [1] Angle blocks have lugs—flanges or projections used for carrying, seating, or supporting something. [15] The ends of the braces and counter-braces should cut or cast to rest squarely against the angle block. [10] [1] The upper lug may be a single flange that fits into a groove cut into the surface of the diagonal, [1] or there may be two to four lugs which form an opening into which the brace and counter-brace are seated. The diagonals are kept in place by tightening the nuts on the vertical posts. [12] Cleats can be nailed to a wooden angle block to help keep braces and counter-braces seated. Alternatively, a hole may be drilled in the lug and brace/counter-brace and a dowel inserted to hold the beam in place. [12] [g] Iron angle blocks should have a hole cast in the upper lugs so that a bolt may pass through the lug and brace/counter-brace, securing the braces in place. [14] The lower lugs in an angle block also have holes cast in them, to permit the angle block to be bolted to the chord. [14] Two or more holes are cast through the center of the angle block, to allow the vertical posts to pass through and be anchored on the other side of the chord. [1]
End panels are the four panels on either side of the end of a Howe truss bridge. These should be the same height as the chords, but not more. [12] The upper chord does not extend past the portal [17] (the space formed by the last four vertical posts at either end of the bridge). [20] The end panels need only a brace, connected from the top of the last vertical post to the end of the lower chord. [17]
Struts are used to connect the two parallels of the chords to prevent lateral bending and reduce vibration. Two diagonals, connecting to the top of the vertical posts, are used. One of the diagonals should be a single piece, while the other is framed into the first piece or made of two pieces connected to it. [21] X-braces, [h] usually made of slender metal rods with threaded ends, are installed between vertical posts to help reduce sway. [14] Knee braces, [i] usually flat bars with eyelets on either end, are used to connect the last strut and last vertical posts on both ends of the bridge. [14]
Individual panels may be prefabricated off-site. [11] When panels are connected to one another on-site, shims are used to pack any spaces and bolted in place. [16] [j]
Floor beams extend between the parallels of a chord and are used to support the stringers and decking. Floor beams may sit atop the chord below them, or they may be hung from the vertical posts. Floor beams generally have the greatest depth of any beam in the bridge. Floor beams are usually placed where two panels meet. If they are placed somewhere mid-panel, the chord must be reinforced to resist bending, buckling, and shear stress. [18]
Stringers are beams set on top of the floor beams, parallel to the chords. A stringer may have a depth-to-width ratio anywhere from 2-to-1 to 6-to-1. A ratio greater than 6-to-1 is avoided in order to avoid buckling. In practice, most wood stringers are 16 inches (410 mm) in width due to limitations in milling. There are usually six stringers in a bridge. [18]
Building the deck for a railroad bridge requires that a stringer lie directly beneath each rail, and that a stringer support each end of the railroad ties. Ties are usually 6 by 8 inches (150 by 200 mm) in cross-section, and 9 to 12 feet (2.7 to 3.7 m) in length. They are set directly on top of the stringers, about 12 inches (300 mm) apart. Guard rails 6 by 8 inches (150 by 200 mm) in cross-section are set 20 inches (510 mm) from the center of the ties, and bolted to every third tie. [18]
The inner truss of a Howe truss is statically indeterminate. There are two paths for stress during loading, a pair of diagonals in compression and a pair in tension. This gives the Howe truss a level of redundancy which allows it to withstand excessive loading (such as the loss of a panel due to collision). [23]
Prestressing is critical to the proper function of a Howe truss. During its initial construction, the diagonals are connected only loosely to the joints, and rely on prestressing, done at a later stage, to perform correctly. Moreover, diagonals in tension can only withstand stress below the prestressing level. (The size of the member does not matter due to the loose fitting of the diagonal to the joint.) Proper prestressing during construction is therefore critical in the correct performance of the bridge. [24]
Maximum stress is placed on the center of the chords when a live load reaches the center of the bridge, or when the live load extends the length of the bridge. Both the vertical posts and braces at the end of the bridge suffer the highest amount of stress. [12]
The stress affecting counter-braces depends on the ratio of live load to dead load per unit of length, and how the live load is distributed across the bridge. A uniform distribution of live load will put no stress on the counter-braces, while putting live load on only a portion of the bridge will create maximum stress on the center counter-braces. [12]
Because of the stress placed on the bridge, the Howe truss is suitable for spans 150 feet (46 m) in length or less. [17] No provision is made in a Howe truss for expansion or contraction due to changes in temperature. [14]
The Howe truss was highly economical due to its ease of construction. The wooden pieces can be designed using little but a steel square and scratch awl, and the truss can be framed using only an adze, auger, and saw. [1] Panels could be prefabricated and transported to the construction site, and sometimes even entire trusses could be manufactured and assembled off-site and transported by rail to the intended location. [11] Some sort of falsework, usually in the form of a trestle, is required to erect the bridge. [21]
The development of the Pratt and Howe trusses spurred the construction of iron bridges in the United States. Until 1850, few iron bridges in the country were longer than 50 feet (15 m). The simple design, ease of manufacture, and ease of construction of the Pratt and Howe trusses spurred Benjamin Henry Latrobe II, chief engineer of the Baltimore and Ohio Railroad, to build large numbers of iron bridges. After two famous iron bridge collapses (one in the United States, the other in the United Kingdom), few of these were built in the North. This meant most iron bridges erected prior to the American Civil War were located in the South. About 1867, a surge in iron bridge building occurred throughout the United States. The most commonly used designs were the Howe truss, Pratt truss, Bollman truss, Fink truss, and Warren truss. [1] [k] The Howe and Pratt trusses found favor because they used far fewer members. [28] The 1962 built, World's Longest, Single Span, Wooden Covered Bridge at Bridgeport State Park, California, uses a Burr-Arch in combination with the Howe-Truss to achieve this over 210' span.
The only maintenance a Howe truss requires is adjustment of the nuts on the vertical posts to equalize strain. [1] The diagonals in a wooden Pratt truss proved difficult to keep in proper adjustment, so the Howe truss became the preferred design for a wooden bridge [1] or for a "transitional" bridge of wood with iron verticals. [2] Engineering professor Horace R. Thayer, writing in 1913, considered the Howe truss to be the best form of wooden truss bridge, and believed it to be the most commonly used truss bridge in the United States at that time. [29]
All-iron Howe trusses began to be built about 1845. [2] Examples include a 50-foot (15 m) long iron Howe truss was built for the Boston and Providence Railroad [2] [30] and a 30-foot (9.1 m) long railroad bridge over the Ohio and Erie Canal in Cleveland. [31] [32]
Iron, however, was the preferred bridge for automobile and railroads, and the Howe truss did not adapt well to all-iron construction. [1] The Pratt truss' single diagonal bracing system meant less cost, and its ability to use wrought-iron stringers under railroad rails and ties, led bridge builders to favor the Pratt over the Howe. [28] [l] Heavier live loads, particularly by railroads, led bridge builders to favor plate girder and Towne lattice bridges for spans less than 60 feet (18 m), and Warren girder bridges for all other spans. [28]
Trusses have been widely used in architecture since ancient times. [33] The Howe truss is widely used in wood buildings, particularly in providing roof support. [34]
A truss is an assembly of members such as beams, connected by nodes, that creates a rigid structure.
A truss bridge is a bridge whose load-bearing superstructure is composed of a truss, a structure of connected elements, usually forming triangular units. The connected elements, typically straight, may be stressed from tension, compression, or sometimes both in response to dynamic loads. There are several types of truss bridges, including some with simple designs that were among the first bridges designed in the 19th and early 20th centuries. A truss bridge is economical to construct primarily because it uses materials efficiently.
The Ashtabula River railroad disaster was caused by the collapse of a bridge over the Ashtabula River near the town of Ashtabula, Ohio, in the United States on December 29, 1876. A Lake Shore and Michigan Southern Railway train, the Pacific Express, was passing over the bridge as it collapsed. All but the lead locomotive plunged into the river. The train's oil lanterns and coal-fired heating stoves set the wooden cars alight. Firefighters declined to extinguish the flames, leaving individuals to try to pull survivors from the wreck. Many who survived the crash burned to death in the wreckage. The accident killed approximately 92 of the 160 people aboard. It was the worst rail accident in the U.S. in the 19th century and the worst rail accident in U.S. history until the Great Train Wreck of 1918. However, it remains the Third-Deadliest rail accident in U.S. history.
A tied-arch bridge is an arch bridge in which the outward-directed horizontal forces of the arch(es) are borne as tension by a chord tying the arch ends rather than by the ground or the bridge foundations. This strengthened chord may be the deck structure itself or consist of separate, independent tie-rods.
A Brown truss is a type of bridge truss, used in covered bridges. It is noted for its economical use of materials and is named after the inventor, Josiah Brown Jr., of Buffalo, New York, who patented it July 7, 1857, as US patent 17,722.
Rexleigh Bridge is a wooden covered bridge over the Batten Kill in Washington County, New York. It is one of 29 historic covered bridges in New York State.
The Mabey Logistic Support Bridge is a portable pre-fabricated truss bridge, designed for use by military engineering units to upgrade routes for heavier traffic, replace civilian bridges damaged by enemy action or floods etc., replace assault and general support bridges and to provide a long span floating bridge capability. The bridge is a variant of the Mabey Compact 200 bridge, with alterations made to suit the military user as well as a ramp system to provide ground clearance to civilian and military vehicles.
Blackfriars Bridge in London, Ontario, Canada is a wrought iron bowstring arch through truss bridge, crossing the North Thames River. The bridge was constructed in 1875 and carries single-lane vehicles, bicycles and pedestrians from Blackfriars Street to Ridout Street North.
Shaw Bridge, also known as Double-Span Whipple Bowstring Truss Bridge, is a historic bridge in Claverack, New York, United States. It carried Van Wyck Lane over Claverack Creek, but is now closed to all traffic, even pedestrians. It is "a structure of outstanding importance to the history of American engineering and transportation technology." Specifically designed by John D. Hutchinson, the bridge employs the basic design of Squire Whipple. It is the only extant "double" Whipple bowstring truss bridge in the U.S., having two identical spans placed in series over a common pier.
A timber roof truss is a structural framework of timbers designed to bridge the space above a room and to provide support for a roof. Trusses usually occur at regular intervals, linked by longitudinal timbers such as purlins. The space between each truss is known as a bay.
Bridge L-158 is a disused railroad bridge over Muscoot Reservoir near Goldens Bridge, New York, United States. Built to carry New York Central Railroad traffic over Rondout Creek near Kingston, it was moved to its current location in 1904.
The Hadley Parabolic Bridge, often referred to locally as the Hadley Bow Bridge, carries Corinth Road across the Sacandaga River in Hadley, New York, United States. It is an iron bridge dating from the late 19th century.
The Clinton Falls Bridge, also known as the Old Mill Bridge and formally as Bridge L-5573, is a historic steel Pratt through truss bridge that spans the Straight River in Clinton Falls Township, Minnesota. It was listed on the National Register of Historic Places in 1997 as Bridge No. L-5573 for having local significance in the theme of engineering. It was nominated for being an example of early steel truss bridge design in Minnesota.
The bridge is significant locally as the only Pratt through-truss bridge remaining in Kosciusko County, and is important regionally as one of the few surviving spans built by the Bellefontaine Bridge and Iron Company.
Starke County Bridge No. 39 is a single span Warren Pony Truss structure. The bridge is located on the northern outskirts of the small town of Knox, Indiana, where Main and Water Streets terminate at the former Penn Central Railroad cut. The bridge spans the rail cut in a northwest–southeast direction, allowing access to Wythougan Park.
This glossary of structural engineering terms pertains specifically to structural engineering and its sub-disciplines. Please see Glossary of engineering for a broad overview of the major concepts of engineering.
The Lincoln Covered Bridge is a historic covered bridge, just south of U.S. Route 4 in West Woodstock, Vermont. Built in 1877, it is one of the only known examples of a wooden Pratt truss bridge in the United States. It was listed on the National Register of Historic Places in 1973.
The Straight Street Bridge is a vehicular bridge over the Passaic River in Paterson, New Jersey, that is listed on the National Register of Historic Places.
The Ball Road-Little Salt Creek Bridge, also known as simply the Ball Road Bridge, was a bridge carrying Ball Road over Little Salt Creek in Jasper Township, Michigan. It was listed on the National Register of Historic Places in 1999. The bridge was later demolished.
Joseph Tomlinson was an English American engineer and architect who built bridges and lighthouses in Canada and the United States. In 1868, he co-designed and oversaw the construction of the Hannibal Bridge, the first permanent crossing of the Missouri River. He was the first person to hold the position of General Superintendent of Lighthouses for the new Dominion of Canada, holding that position beginning in January 1870. For eight years, he worked building railroad bridges for the Canadian government, and designed one of the most impressive bridges on the Canadian Pacific Railway where it crossed the Fraser River. He designed a railroad bridge over the Ashtabula River in Ohio, but was fired from the project after he refused to make supervisor-ordered changes to the design which he considered unsafe. The bridge failed on December 29, 1876, killing 92 people in a train derailment.
