In mathematics, the Jacobi elliptic functions are a set of basic elliptic functions. They are found in the description of the motion of a pendulum, as well as in the design of electronic elliptic filters. While trigonometric functions are defined with reference to a circle, the Jacobi elliptic functions are a generalization which refer to other conic sections, the ellipse in particular. The relation to trigonometric functions is contained in the notation, for example, by the matching notation for . The Jacobi elliptic functions are used more often in practical problems than the Weierstrass elliptic functions as they do not require notions of complex analysis to be defined and/or understood. They were introduced by Carl Gustav JakobJacobi(1829). Carl Friedrich Gauss had already studied special Jacobi elliptic functions in 1797, the lemniscate elliptic functions in particular,[1] but his work was published much later.
There are twelve Jacobi elliptic functions denoted by , where and are any of the letters , , , and . (Functions of the form are trivially set to unity for notational completeness.) is the argument, and is the parameter, both of which may be complex. In fact, the Jacobi elliptic functions are meromorphic in both and .[2] The distribution of the zeros and poles in the -plane is well-known. However, questions of the distribution of the zeros and poles in the -plane remain to be investigated.[2]
In the complex plane of the argument , the twelve functions form a repeating lattice of simple poles and zeroes.[3] Depending on the function, one repeating parallelogram, or unit cell, will have sides of length or on the real axis, and or on the imaginary axis, where and are known as the quarter periods with being the elliptic integral of the first kind. The nature of the unit cell can be determined by inspecting the "auxiliary rectangle" (generally a parallelogram), which is a rectangle formed by the origin at one corner, and as the diagonally opposite corner. As in the diagram, the four corners of the auxiliary rectangle are named , , , and , going counter-clockwise from the origin. The function will have a zero at the corner and a pole at the corner. The twelve functions correspond to the twelve ways of arranging these poles and zeroes in the corners of the rectangle.
When the argument and parameter are real, with , and will be real and the auxiliary parallelogram will in fact be a rectangle, and the Jacobi elliptic functions will all be real valued on the real line.
Since the Jacobian elliptic functions are doubly periodic in , they factor through a torus – in effect, their domain can be taken to be a torus, just as cosine and sine are in effect defined on a circle. Instead of having only one circle, we now have the product of two circles, one real and the other imaginary. The complex plane can be replaced by a complex torus. The circumference of the first circle is and the second , where and are the quarter periods. Each function has two zeroes and two poles at opposite positions on the torus. Among the points , , , there is one zero and one pole.
The Jacobian elliptic functions are then doubly periodic, meromorphic functions satisfying the following properties:
There is a simple zero at the corner , and a simple pole at the corner.
The complex number is equal to half the period of the function ; that is, the function is periodic in the direction , with the period being . The function is also periodic in the other two directions and , with periods such that and are quarter periods.
Jacobi elliptic function
Jacobi elliptic function
Jacobi elliptic function
Jacobi elliptic function
Plots of four Jacobi Elliptic Functions in the complex plane of , illustrating their double periodic behavior. Images generated using a version of the domain coloring method.[4] All have values of equal to .
Notation
The elliptic functions can be given in a variety of notations, which can make the subject unnecessarily confusing. Elliptic functions are functions of two variables. The first variable might be given in terms of the amplitude, or more commonly, in terms of given below. The second variable might be given in terms of the parameter, or as the elliptic modulus, where , or in terms of the modular angle, where . The complements of and are defined as and . These four terms are used below without comment to simplify various expressions.
The twelve Jacobi elliptic functions are generally written as where and are any of the letters , , , and . Functions of the form are trivially set to unity for notational completeness. The “major” functions are generally taken to be , and from which all other functions can be derived and expressions are often written solely in terms of these three functions, however, various symmetries and generalizations are often most conveniently expressed using the full set. (This notation is due to Gudermann and Glaisher and is not Jacobi's original notation.)
Throughout this article, .
The functions are notationally related to each other by the multiplication rule: (arguments suppressed)
from which other commonly used relationships can be derived:
The multiplication rule follows immediately from the identification of the elliptic functions with the Neville theta functions[5]
Also note that:
Definition in terms of inverses of elliptic integrals
There is a definition, relating the elliptic functions to the inverse of the incomplete elliptic integral of the first kind. These functions take the parameters and as inputs. The that satisfies
is called the Jacobi amplitude:
In this framework, the elliptic sine snu (Latin: sinus amplitudinis) is given by
and the elliptic cosine cnu (Latin: cosinus amplitudinis) is given by
and the delta amplitude dnu (Latin: delta amplitudinis)[note 1]
In the above, the value is a free parameter, usually taken to be real such that (but can be complex in general), and so the elliptic functions can be thought of as being given by two variables, and the parameter. The remaining nine elliptic functions are easily built from the above three (, , ), and are given in a section below. Note that when , that then equals the quarter period.
In the most general setting, is a multivalued function (in ) with infinitely many logarithmic branch points (the branches differ by integer multiples of ), namely the points and where .[6] This multivalued function can be made single-valued by cutting the complex plane along the line segments joining these branch points (the cutting can be done in non-equivalent ways, giving non-equivalent single-valued functions), thus making analytic everywhere except on the branch cuts. In contrast, and other elliptic functions have no branch points, give consistent values for every branch of , and are meromorphic in the whole complex plane. Since every elliptic function is meromorphic in the whole complex plane (by definition), (when considered as a single-valued function) is not an elliptic function.
However, a particular cutting for can be made in the -plane by line segments from to with ; then it only remains to define at the branch cuts by continuity from some direction. Then becomes single-valued and singly-periodic in with the minimal period and it has singularities at the logarithmic branch points mentioned above. If and , is continuous in on the real line. When , the branch cuts of in the -plane cross the real line at for ; therefore for , is not continuous in on the real line and jumps by on the discontinuities.
But defining this way gives rise to very complicated branch cuts in the -plane (not the -plane); they have not been fully described as of yet.
Then the Jacobi epsilon function can be defined as
for and and by analytic continuation in each of the variables otherwise: the Jacobi epsilon function is meromorphic in the whole complex plane (in both and ). Alternatively, throughout both the -plane and -plane,[7]
is well-defined in this way because all residues of are zero, so the integral is path-independent. So the Jacobi epsilon relates the incomplete elliptic integral of the first kind to the incomplete elliptic integral of the second kind:
The Jacobi epsilon function is not an elliptic function, but it appears when differentiating the Jacobi elliptic functions with respect to the parameter.
The Jacobi zn function is defined by
It is a singly periodic function which is meromorphic in , but not in (due to the branch cuts of and ). Its minimal period in is . It is related to the Jacobi zeta function by
Historically, the Jacobi elliptic functions were first defined by using the amplitude. In more modern texts on elliptic functions, the Jacobi elliptic functions are defined by other means, for example by ratios of theta functions (see below), and the amplitude is ignored.
In modern terms, the relation to elliptic integrals would be expressed by (or ) instead of .
Definition as trigonometry: the Jacobi ellipse
are defined on the unit circle, with radius r=1 and angle arc length of the unit circle measured from the positive x-axis. Similarly, Jacobi elliptic functions are defined on the unit ellipse,[citation needed] with a=1. Let
then:
For each angle the parameter
(the incomplete elliptic integral of the first kind) is computed. On the unit circle (), would be an arc length. However, the relation of to the arc length of an ellipse is more complicated.[8]
Let be a point on the ellipse, and let be the point where the unit circle intersects the line between and the origin . Then the familiar relations from the unit circle:
read for the ellipse:
So the projections of the intersection point of the line with the unit circle on the x- and y-axes are simply and . These projections may be interpreted as 'definition as trigonometry'. In short:
For the and value of the point with and parameter we get, after inserting the relation:
into: that:
The latter relations for the x- and y-coordinates of points on the unit ellipse may be considered as generalization of the relations for the coordinates of points on the unit circle.
The following table summarizes the expressions for all Jacobi elliptic functions pq(u,m) in the variables (x,y,r) and (φ,dn) with
Jacobi elliptic functions pq[u,m] as functions of {x,y,r} and {φ,dn}
q
c
s
n
d
p
c
1
s
1
n
1
d
1
Definition in terms of the Jacobi theta functions
Using elliptic integrals
Equivalently, Jacobi's elliptic functions can be defined in terms of the theta functions.[9] With such that , let
and , , . Then with , , and ,
The Jacobi zn function can be expressed by theta functions as well:
where denotes the partial derivative with respect to the first variable.
Using modular inversion
In fact, the definition of the Jacobi elliptic functions in Whittaker & Watson is stated a little bit differently than the one given above (but it's equivalent to it) and relies on modular inversion: The function, defined by
where is the upper half-plane in the complex plane, is the boundary of and
In this way, each can be associated with one and only one. Then Whittaker & Watson define the Jacobi elliptic functions by
where . In the book, they place an additional restriction on (that ), but it is in fact not a necessary restriction (see the Cox reference). Also, if or , the Jacobi elliptic functions degenerate to non-elliptic functions which is described below.
Simplifications of complicated products of the Jacobi elliptic functions are often made easier using these identities.
Jacobi transformations
The Jacobi imaginary transformations
The Jacobi imaginary transformations relate various functions of the imaginary variable i u or, equivalently, relations between various values of the m parameter. In terms of the major functions:[12]:506
Using the multiplication rule, all other functions may be expressed in terms of the above three. The transformations may be generally written as . The following table gives the for the specified pq(u,m).[11] (The arguments are suppressed)
Jacobi Imaginary transformations
q
c
s
n
d
p
c
1
i ns
nc
nd
s
−i sn
1
−i sc
−i sd
n
cn
i cs
1
cd
d
dn
i ds
dc
1
Since the hyperbolic trigonometric functions are proportional to the circular trigonometric functions with imaginary arguments, it follows that the Jacobi functions will yield the hyperbolic functions for m=1.[5]:249 In the figure, the Jacobi curve has degenerated to two vertical lines at x=1 and x=−1.
The Jacobi real transformations
The Jacobi real transformations[5]:308 yield expressions for the elliptic functions in terms with alternate values of m. The transformations may be generally written as . The following table gives the for the specified pq(u,m).[11] (The arguments are suppressed)
Jacobi real transformations
q
c
s
n
d
p
c
s
n
d
Other Jacobi transformations
Jacobi's real and imaginary transformations can be combined in various ways to yield three more simple transformations .[5]:214 The real and imaginary transformations are two transformations in a group (D3 or anharmonic group) of six transformations. If
is the transformation for the m parameter in the real transformation, and
is the transformation of m in the imaginary transformation, then the other transformations can be built up by successive application of these two basic transformations, yielding only three more possibilities:
These five transformations, along with the identity transformation (μU(m)=m) yield the six-element group. With regard to the Jacobi elliptic functions, the general transformation can be expressed using just three functions:
where i = U, I, IR, R, RI, or RIR, identifying the transformation, γi is a multiplication factor common to these three functions, and the prime indicates the transformed function. The other nine transformed functions can be built up from the above three. The reason the cs, ns, ds functions were chosen to represent the transformation is that the other functions will be ratios of these three (except for their inverses) and the multiplication factors will cancel.
The following table lists the multiplication factors for the three ps functions, the transformed m's, and the transformed function names for each of the six transformations.[5]:214 (As usual, k2=m, 1−k2=k12=m′ and the arguments () are suppressed)
Parameters for the six transformations
Transformation i
cs'
ns'
ds'
U
1
m
cs
ns
ds
I
i
m'
ns
cs
ds
IR
i k
−m'/m
ds
cs
ns
R
k
1/m
ds
ns
cs
RI
i k1
1/m'
ns
ds
cs
RIR
k1
−m/m'
cs
ds
ns
Thus, for example, we may build the following table for the RIR transformation.[11] The transformation is generally written (The arguments are suppressed)
The RIR transformation
q
c
s
n
d
p
c
1
k' cs
cd
cn
s
sc
1
sd
sn
n
dc
ds
1
dn
d
nc
ns
nd
1
The value of the Jacobi transformations is that any set of Jacobi elliptic functions with any real-valued parameter m can be converted into another set for which and, for real values of u, the function values will be real.[5]:p. 215
Amplitude transformations
In the following, the second variable is suppressed and is equal to :
where both identities are valid for all such that both sides are well-defined.
With
we have
where all the identities are valid for all such that both sides are well-defined.
The Jacobi hyperbola
Introducing complex numbers, our ellipse has an associated hyperbola:
from applying Jacobi's imaginary transformation[11] to the elliptic functions in the above equation for x andy.
It follows that we can put . So our ellipse has a dual ellipse with m replaced by 1-m. This leads to the complex torus mentioned in the Introduction.[13] Generally, m may be a complex number, but when m is real and m<0, the curve is an ellipse with major axis in the x direction. At m=0 the curve is a circle, and for 0<m<1, the curve is an ellipse with major axis in the y direction. At m=1, the curve degenerates into two vertical lines at x=±1. For m>1, the curve is a hyperbola. When m is complex but not real, x or y or both are complex and the curve cannot be described on a real x-y diagram.
Minor functions
Reversing the order of the two letters of the function name results in the reciprocals of the three functions above:
Similarly, the ratios of the three primary functions correspond to the first letter of the numerator followed by the first letter of the denominator:
More compactly, we have
where p and q are any of the letters s, c, d.
Periodicity, poles, and residues
In the complex plane of the argument u, the Jacobi elliptic functions form a repeating pattern of poles (and zeroes). The residues of the poles all have the same absolute value, differing only in sign. Each function pq(u,m) has an "inverse function" (in the multiplicative sense) qp(u,m) in which the positions of the poles and zeroes are exchanged. The periods of repetition are generally different in the real and imaginary directions, hence the use of the term "doubly periodic" to describe them.
For the Jacobi amplitude and the Jacobi epsilon function:
The double periodicity of the Jacobi elliptic functions may be expressed as:
where α and β are any pair of integers. K(⋅) is the complete elliptic integral of the first kind, also known as the quarter period. The power of negative unity (γ) is given in the following table:
q
c
s
n
d
p
c
0
β
α+β
α
s
β
0
α
α+β
n
α+β
α
0
β
d
α
α+β
β
0
When the factor (−1)γ is equal to −1, the equation expresses quasi-periodicity. When it is equal to unity, it expresses full periodicity. It can be seen, for example, that for the entries containing only α when α is even, full periodicity is expressed by the above equation, and the function has full periods of 4K(m) and 2iK(1−m). Likewise, functions with entries containing only β have full periods of 2K(m) and 4iK(1−m), while those with α + β have full periods of 4K(m) and 4iK(1−m).
In the diagram on the right, which plots one repeating unit for each function, indicating phase along with the location of poles and zeroes, a number of regularities can be noted: The inverse of each function is opposite the diagonal, and has the same size unit cell, with poles and zeroes exchanged. The pole and zero arrangement in the auxiliary rectangle formed by (0,0), (K,0), (0,K′) and (K,K′) are in accordance with the description of the pole and zero placement described in the introduction above. Also, the size of the white ovals indicating poles are a rough measure of the absolute value of the residue for that pole. The residues of the poles closest to the origin in the figure (i.e. in the auxiliary rectangle) are listed in the following table:
Residues of Jacobi Elliptic Functions
q
c
s
n
d
p
c
1
s
n
1
d
-1
1
When applicable, poles displaced above by 2K or displaced to the right by 2K′ have the same value but with signs reversed, while those diagonally opposite have the same value. Note that poles and zeroes on the left and lower edges are considered part of the unit cell, while those on the upper and right edges are not.
The information about poles can in fact be used to characterize the Jacobi elliptic functions:[14]
The function is the unique elliptic function having simple poles at (with ) with residues taking the value at .
The function is the unique elliptic function having simple poles at (with ) with residues taking the value at .
The function is the unique elliptic function having simple poles at (with ) with residues taking the value at .
To get x3, we take the tangent of twice the arctangent of the modulus.
Also this equation leads to the sn-value of the third of K:
These equations lead to the other values of the Jacobi-Functions:
Fifth K formula
Following equation has following solution:
To get the sn-values, we put the solution x into following expressions:
Relations between squares of the functions
Relations between squares of the functions can be derived from two basic relationships (Arguments (u,m) suppressed): where m+m'=1. Multiplying by any function of the form nq yields more general equations:
With q=d, these correspond trigonometrically to the equations for the unit circle () and the unit ellipse (), with x=cd, y=sd and r=nd. Using the multiplication rule, other relationships may be derived. For example:
Addition theorems
The functions satisfy the two square relations (dependence on m suppressed)
From this we see that (cn, sn, dn) parametrizes an elliptic curve which is the intersection of the two quadrics defined by the above two equations. We now may define a group law for points on this curve by the addition formulas for the Jacobi functions[3]
The Jacobi epsilon and zn functions satisfy a quasi-addition theorem:
Double angle formulae can be easily derived from the above equations by setting x=y.[3] Half angle formulae[11][3] are all of the form:
where:
Jacobi elliptic functions as solutions of nonlinear ordinary differential equations
Derivatives with respect to the first variable
The derivatives of the three basic Jacobi elliptic functions (with respect to the first variable, with fixed) are:
These can be used to derive the derivatives of all other functions as shown in the table below (arguments (u,m) suppressed):
as . This is notable for its rapid convergence. It is then trivial to compute all Jacobi elliptic functions from the Jacobi amplitude on the real line.[note 2]
In conjunction with the addition theorems for elliptic functions (which hold for complex numbers in general) and the Jacobi transformations, the method of computation described above can be used to compute all Jacobi elliptic functions in the whole complex plane.
Another method of fast computation of the Jacobi elliptic functions via the arithmetic–geometric mean, avoiding the computation of the Jacobi amplitude, is due to Herbert E. Salzer:[16]
Let
Set
Then
as .
Yet, another method for a rapidly converging fast computation of the Jacobi elliptic sine function found in the literature is shown below.[17]
Let:
Then set:
Then:
.
Approximation in terms of hyperbolic functions
The Jacobi elliptic functions can be expanded in terms of the hyperbolic functions. When is close to unity, such that and higher powers of can be neglected, we have:[18][19]
The inverses of the Jacobi elliptic functions can be defined similarly to the inverse trigonometric functions; if , . They can be represented as elliptic integrals,[23][24][25] and power series representations have been found.[26][3]
In integral calculus, an elliptic integral is one of a number of related functions defined as the value of certain integrals, which were first studied by Giulio Fagnano and Leonhard Euler. Their name originates from their originally arising in connection with the problem of finding the arc length of an ellipse.
In classical mechanics, a harmonic oscillator is a system that, when displaced from its equilibrium position, experiences a restoring force F proportional to the displacement x: where k is a positive constant.
In mathematics, the Weierstrass elliptic functions are elliptic functions that take a particularly simple form. They are named for Karl Weierstrass. This class of functions are also referred to as ℘-functions and they are usually denoted by the symbol ℘, a uniquely fancy script p. They play an important role in the theory of elliptic functions, i.e., meromorphic functions that are doubly periodic. A ℘-function together with its derivative can be used to parameterize elliptic curves and they generate the field of elliptic functions with respect to a given period lattice.
In mathematics, theta functions are special functions of several complex variables. They show up in many topics, including Abelian varieties, moduli spaces, quadratic forms, and solitons. As Grassmann algebras, they appear in quantum field theory.
In mathematics, Felix Klein's j-invariant or j function, regarded as a function of a complex variable τ, is a modular function of weight zero for special linear group SL(2, Z) defined on the upper half-plane of complex numbers. It is the unique such function that is holomorphic away from a simple pole at the cusp such that
In physics, the Hamilton–Jacobi equation, named after William Rowan Hamilton and Carl Gustav Jacob Jacobi, is an alternative formulation of classical mechanics, equivalent to other formulations such as Newton's laws of motion, Lagrangian mechanics and Hamiltonian mechanics.
In general relativity, Schwarzschild geodesics describe the motion of test particles in the gravitational field of a central fixed mass that is, motion in the Schwarzschild metric. Schwarzschild geodesics have been pivotal in the validation of Einstein's theory of general relativity. For example, they provide accurate predictions of the anomalous precession of the planets in the Solar System and of the deflection of light by gravity.
In mathematics, specifically the theory of elliptic functions, the nome is a special function that belongs to the non-elementary functions. This function is of great importance in the description of the elliptic functions, especially in the description of the modular identity of the Jacobi theta function, the Hermite elliptic transcendents and the Weber modular functions, that are used for solving equations of higher degrees.
In mathematics, the quarter periodsK(m) and iK ′(m) are special functions that appear in the theory of elliptic functions.
In mathematics, the lemniscate elliptic functions are elliptic functions related to the arc length of the lemniscate of Bernoulli. They were first studied by Giulio Fagnano in 1718 and later by Leonhard Euler and Carl Friedrich Gauss, among others.
A pendulum is a body suspended from a fixed support such that it freely swings back and forth under the influence of gravity. When a pendulum is displaced sideways from its resting, equilibrium position, it is subject to a restoring force due to gravity that will accelerate it back towards the equilibrium position. When released, the restoring force acting on the pendulum's mass causes it to oscillate about the equilibrium position, swinging it back and forth. The mathematics of pendulums are in general quite complicated. Simplifying assumptions can be made, which in the case of a simple pendulum allow the equations of motion to be solved analytically for small-angle oscillations.
The Rogers–Ramanujan continued fraction is a continued fraction discovered by Rogers (1894) and independently by Srinivasa Ramanujan, and closely related to the Rogers–Ramanujan identities. It can be evaluated explicitly for a broad class of values of its argument.
In mathematics, an elliptic hypergeometric series is a series Σcn such that the ratio cn/cn−1 is an elliptic function of n, analogous to generalized hypergeometric series where the ratio is a rational function of n, and basic hypergeometric series where the ratio is a periodic function of the complex number n. They were introduced by Date-Jimbo-Kuniba-Miwa-Okado (1987) and Frenkel & Turaev (1997) in their study of elliptic 6-j symbols.
In statistical mechanics, the eight-vertex model is a generalization of the ice-type (six-vertex) models. It was discussed by Sutherland and Fan & Wu, and solved by Rodney Baxter in the zero-field case.
In fluid dynamics, a cnoidal wave is a nonlinear and exact periodic wave solution of the Korteweg–de Vries equation. These solutions are in terms of the Jacobi elliptic function cn, which is why they are coined cnoidal waves. They are used to describe surface gravity waves of fairly long wavelength, as compared to the water depth.
In mathematics, the Jacobi zeta functionZ(u) is the logarithmic derivative of the Jacobi theta function Θ(u). It is also commonly denoted as
In mathematics, the modular lambda function λ(τ) is a highly symmetric Holomorphic function on the complex upper half-plane. It is invariant under the fractional linear action of the congruence group Γ(2), and generates the function field of the corresponding quotient, i.e., it is a Hauptmodul for the modular curve X(2). Over any point τ, its value can be described as a cross ratio of the branch points of a ramified double cover of the projective line by the elliptic curve , where the map is defined as the quotient by the [−1] involution.
In mathematics, the Neville theta functions, named after Eric Harold Neville, are defined as follows:
In mathematics, the Dixon elliptic functions sm and cm are two elliptic functions that map from each regular hexagon in a hexagonal tiling to the whole complex plane. Because these functions satisfy the identity , as real functions they parametrize the cubic Fermat curve , just as the trigonometric functions sine and cosine parametrize the unit circle .
In mathematics, Zolotarev polynomials are polynomials used in approximation theory. They are sometimes used as an alternative to the Chebyshev polynomials where accuracy of approximation near the origin is of less importance. Zolotarev polynomials differ from the Chebyshev polynomials in that two of the coefficients are fixed in advance rather than allowed to take on any value. The Chebyshev polynomials of the first kind are a special case of Zolotarev polynomials. These polynomials were introduced by Russian mathematician Yegor Ivanovich Zolotarev in 1868.
N. I. Akhiezer, Elements of the Theory of Elliptic Functions (1970) Moscow, translated into English as AMS Translations of Mathematical Monographs Volume 79 (1990) AMS, Rhode Island ISBN0-8218-4532-2
Lowan, Blanch und Horenstein: On the Inversion of the q-Series Associated with Jacobian Elliptic Functions. Bull. Amer. Math. Soc. 48, 1942
H. Ferguson, D. E. Nielsen, G. Cook: A partition formula for the integer coefficients of the theta function nome. Mathematics of computation, Volume 29, Nummer 131, Juli 1975
J. D. Fenton and R. S. Gardiner-Garden: Rapidly-convergent methods for evaluating elliptic integrals and theta and elliptic functions. J. Austral. Math. Soc. (Series B) 24, 1982, S. 57
Adolf Kneser: Neue Untersuchung einer Reihe aus der Theorie der elliptischen Funktionen. J. reine u. angew. Math. 157, 1927. pages 209 – 218
This page is based on this Wikipedia article Text is available under the CC BY-SA 4.0 license; additional terms may apply. Images, videos and audio are available under their respective licenses.