Laser welding of polymers

Last updated

Laser welding of polymers is a set of methods used to join polymeric components through the use of a laser. It can be performed using CO2 lasers, Nd:YAG lasers, Diode lasers and Fiber lasers. [1]

Contents

When a laser encounters the surface of plastics, it can be reflected, absorbed or penetrate through the thickness of a component. Laser welding of plastics is based on the energy absorption of laser radiation, which can be reinforced by additives and fillers.

Laser welding techniques include:

Because of high joining speeds, low residual stresses and excellent weld appearances, laser welding processes have been widely used for automotive and medical applications.

Laser sources

The types of lasers used in the welding of polymers include CO2 lasers, Nd:YAG lasers, Diode lasers and fiber lasers. CO2 lasers are mostly applied to weld thin films and thin plastics due to the high energy absorption coefficients of most plastics. Nd:YAG lasers and Diode lasers produce short wavelength radiation, which transmit through several millimeters of unpigmented polymer. [2] They are used in the transmission laser welding techniques.

Carbon dioxide lasers

Carbon dioxide lasers have a wavelength of 10.6 μm which is rapidly absorbed by most polymers. Because of the high-energy absorption coefficients, processing of plastics using CO2 can be done rapidly with low laser powers. This type of laser can be used in direct welding of polymers or cutting. However, the penetration of CO2 lasers is less than 0.5 mm and is mostly applicable for the welding of thin film and surface heating. Because the beam cannot be transmitted by silicon fiber, the beam is commonly delivered by mirrors. [3]

Nd:YAG lasers

Nd:YAG lasers have a wavelength in the range of 0.9 - 1.1 μm, with 1064 nm being the most common. These lasers provide a high beam quality allowing for small spot sizes. This type of beam can be delivered via fiber optic cable. [3]

Diode lasers

The wavelength of diode lasers is typically in the 780 - 980 nm wavelength range. [2] Compared with Nd:YAG laser and CO2 laser, diode laser has supreme advantage in energy efficiency. The high-energy light wave can penetrate a thickness of a few millimeters in semicrystalline plastics and further in unpigmented amorphous plastics. [2] Diode lasers can be either fiber delivered or local to the weld location. The relatively small size makes assembling arrays for larger foot prints possible.

Fiber laser

Fiber lasers typically exhibit wavelengths ranging from 1000 to 3500 nm. [3] The expanded range of wavelengths has allowed for the development of through transmission welding without additional absorbing additives. [4]

Equipment

The equipment settings may vary greatly in design and complexity. However, there are five components included in most of the machines:

Generator/Power supply

This component transforms the received voltage and frequency to the corresponding voltage, current and frequency to the laser source. Diode laser and fiber laser are the two most commonly used system for laser welding. [1]

Control interface

The control interface is an interface between operator and machine to monitor operations of the system. It is constructed by logic circuits to send operators the information of machine status and welding parameters. [1] Depending on different laser modes, the control interface will vary the parameters allowable to change. [5]

Actuator

This component is a press activated by pneumatical and electrical power. [1] It compresses the part in the upper fixture to touch the components in the lower fixture and apply pre-determined loads during welding processes. [5] Displacement controls are added to actuators to monitor precisely the movements. [1]

Lower fixture

Lower fixture is a jig structure that locates the lower part of a joint. [5] It provides locations and alignments that ensure the welding of components with tight tolerances.

Upper fixture

The upper fixture is the most complicated and important component in the whole system. Laser beam is generated in this component to heat up the welding parts. The design of upper fixture often varies from laser sources and heating modes. For example, when a YAG laser or a diode laser is used as the heat source, optical fibers are often employed to provide mobility. However, the welding part cannot move. [5]

Laser interaction with polymers

There are three types of interactions that can occur between laser radiation and plastics:

The extent of individual interaction is dependent upon materials properties, laser wavelength, laser intensity and beam speed. [3]

Reflection

Reflected and transmitted energy Wave reflection medium.png
Reflected and transmitted energy

Reflection of incident laser radiation is typically on the order of 5 to 10% in most polymers, which is low compared with absorption and transmission. [6] The fraction of reflection (R) can be determined by the following equation,

where is the index of refraction of the plastics and is the index of refraction of air (~1). [5]

Transmission

Transmission of laser energy through certain polymers allows for processes such as through transmission welding. When the laser beam travel through the interfaces between different medium, the laser beam is refracted unless the path is perpendicular to the surface. This effect needs to be considered when laser travels through multi-layer to reach the joint region. [4]

Internal scattering occur when laser pass through the thickness in semicrystalline plastics, where crystalline and amorphous phase have different index of refraction. Scattering can also occur in crystalline and amorphous plastics with reinforcement like glass fiber and certain colorants and additives. [1] In transmission laser welding, such effect can reduce the effective energy of laser radiation towards joint area and limit the thickness of components. [5]

Absorption

Laser absorption can occur at the surface of plastics or during transmission through thickness. The amount of laser energy absorbed by a polymer is a function of the laser wavelength, polymer absorptivity, polymer crystallinity, and additives (i.e. composite reinforcements, pigments, etc.). [1] The absorption at surface has two possible ways, photolytic and pyrolytic.

The heat distribution within a laser welded polymer is dictated by the Bouger–Lambert law of absorption. [6]

I(z) = I(z=0) eKz

where I(z) is the laser intensity at a certain depth z, I(z=0) is the laser intensity at the surface, K is the absorption constant. [6]

Effect of additives

Polymers often have secondary elements added to them for various reasons (i.e. strength, color, absorption, etc.). These elements can have a profound effect on the laser interaction with the polymer component. Some common additives and their effect on laser welding are described below.

Reinforcements

Various fibers are added to polymeric materials to create higher strength composites. Some typical fiber materials include: glass, carbon fiber, wood, etc. When the laser beam interacts with these materials it can get scattered or absorbed, changing the optical properties from that of the base polymer. In laser transmission welding, a transparent material with reinforcement may absorb or dilute the energy beam more, effecting the quality of the weld. [6] High contents of glass fiber content increase the scattering within the plastics and raise the laser energy input for welding a certain thickness. [2]

Colorants

Colorants (pigments) are added to polymers for various reasons including aesthetics and functional requirements (such as optics). Certain color additives, such as titanium dioxide, can have a negative impact on the laser weldability of a polymer. The titanium dioxide provides a white coloring to polymers but also scatters laser energy making it difficult to weld. Another color additive, carbon black, is a very effective energy absorber and is often added to create welds. By controlling the concentration of carbon black with the absorbing polymer it is possible to control the effective area of the laser weld. [7]

Laser application configurations

The laser beam energy can be delivered to the required areas through a variety of configurations. The four most common approaches include:

Contour heating

In the contour heating (laser scanning or laser moving) technique, a laser beam of fixed dimension passes through the desired area to create a continuous weld seam. [8] [7] The laser source is manipulated by a galvanic mirror or a robotic system to scan at a fast rate. [5] The benefit of contour heating is that the weld can be performed with a single laser source, which can be reprogramed for different applications; however, due to the localized heating area, uneven contact between welding components can occur and form weld voids. [5] The important parameters for this technique include: laser wavelength, laser power, traverse speed, and polymer properties. [8]

Simultaneous heating

In the simultaneous heating approach, a beam spot of appropriate size is used to irradiate the entire weld area without the need for relative movement between the work piece and the laser source. For creating a weld with a large area, multiple laser sources can be combined to melt the selected region simultaneously. This approach can be adopted to substitute ultrasonic welding in the case of welding components sensitive to vibration. Key processing parameters for this approach include: laser wavelength, laser power, heating time, clamp pressure, cooling time, and polymer properties. [3] [8]

Quasi-simultaneous heating (QSLW)

Laser heating configurations Laser heating configurations.png
Laser heating configurations

In the quasi-simultaneous heating, a work area is irradiated by the use of scanning mirrors. The mirrors raster the laser beam over the entire work area rapidly, creating a simultaneously melted region. Some of the important parameters for this technique include: laser wavelength, laser power, heating time, cooling time, polymer properties. [8]

Masked heating

Masked heating is a process of laser line scanning through a region with a mask, which ensures that only the selected areas can be heated when the laser pass through. [3] [5] Masks can be made out of laser cut steel, or other materials that effectively block the laser radiation. This approach is capable of creating micro-scale welds on components with complex geometries. [3] Key processing parameters for this approach include: laser wavelength, laser power, heating time, clamp pressure, cooling time, and polymer properties. [7] [8]

Laser welding techniques

Depending on different interactions between laser and thermoplastics, four different laser welding techniques have been developed for plastic joining. CO2 lasers have good surface absorption for most thermoplastics, hence they are applied for direct laser welding and laser surface heating. Through transmission laser welding and intermediate film welding require the deep penetration of laser beam, so YAG lasers and diode lasers are the most common sources for these techniques.

Direct laser welding

Direct laser welding of polymers Direct Laser Energy Welding of Polymers.png
Direct laser welding of polymers

Similar to laser welding of metals, in direct laser welding the surface of the polymer is heated to create a melt zone that joins two components together. This approach can be used to create butt joints and lap joints with complete penetration. Laser wavelengths between 2 and 10.6 μm are used for this process due to their high absorptivity in polymers. [3]

Laser surface heating

Laser surface heating is similar to non-contact hot plate welding in that mirrors are placed between components to create a molten surface layer. The exposure duration is usually between 2-10 s. [5] Then the mirror is retracted and the components are pressed together to form a joint. Process parameters for laser surface heating include the laser output, wavelength, heating time, change-over time, and forging pressure and time. [5]

Through transmission laser welding (TTLW)

Diagram of transmission laser welding of polymers Transmission welding diagram.png
Diagram of transmission laser welding of polymers

Through transmission laser welding of polymers is a method to create a joint at the interface between two polymer components with different transparencies to laser wavelengths. The upper component is transparent to the laser wavelength between 0.8 μm to 1.05 μm, and the lower component is either opaque in nature, or modified by the addition of colorants which promote the absorption of laser radiation. A typical colorant is carbon black that absorb most of the electromagnetic wavelength. [5] When the joint is irradiated by the laser, the transparent layer passes the light with minimal loss while the opaque layer absorbs the laser energy and heats up. [8]

The two components are held by the lower fixture to control alignment and a small clamping force is added to the upper part to form intimate contact. A melt layer is then created at the interface between the two components, composed of a mixture of two plastic materials.

There are four different modes of transmission laser welding: scanning mode, simultaneous, quasi-simultaneous, and mask heating. [8]

Many benefits can be obtained by transmission laser welding such as fast welding velocity, flexibility, good cosmetic properties and low residual stresses. From processing perspectives, laser welding can be performed in the pre-assembled conditions, reducing the necessity for complex fixtures; however, this method is not suitable for plastics with high crystallinity due to refraction and geometric limitations. [5]

Intermediate film welding

Intermediate film welding is a method to join incompatible plastic components by using an intermediate film between them. Similar to transmission welding, laser radiation passes through the transparent components and melts the intermediate layers to create a joint. [1] This film can be made of an opaque thermoplastic, solvent, viscous fluid, or other substances that heat up upon exposure to laser energy. The combination of intermediate films and adhesion promoters is able to join incompatible thermoplastics together. [1] The thin layer then generates the heat required to fuse the system together. [8]

Applications

Car ignition key BMW Car Key.jpg
Car ignition key

Automotive applications

The black body of car keys is welded by the Through Transmission Laser Welding (TTLW) technique, in which laser radiation transmits through the upper component and forms a joint at the interface. Carbon black is added to the lower part of car keys to absorb laser radiation. The black color of the upper part is made by the addition of dye, which makes the component appear black but transparent to laser radiation.

Other applications of laser welding in automotive industry include brake fluid reservoirs and lighting components. [8]

IV bag Iv1-07 014.jpg
IV bag

Medical applications

Laser welding of plastics is applied to weld medical devices like IV-bags. Joints of high geometrical complexity can be produced by laser welding without particulate formation. This is critical for the safety of patients, when welding techniques are applied to produce IV-bags containing blood. In addition, flashes generated during welding can cause blood turbulences and destroy blood platelets. A good control of the laser power avoids flash formation and thus protects the blood cells from damage.

Related Research Articles

<span class="mw-page-title-main">Laser</span> Device which emits light via optical amplification

A laser is a device that emits light through a process of optical amplification based on the stimulated emission of electromagnetic radiation. The word laser is an anacronym that originated as an acronym for light amplification by stimulated emission of radiation. The first laser was built in 1960 by Theodore Maiman at Hughes Research Laboratories, based on theoretical work by Charles H. Townes and Arthur Leonard Schawlow.

<span class="mw-page-title-main">Ultraviolet</span> Energetic, invisible light energy range

Ultraviolet (UV) light is electromagnetic radiation of wavelengths of 10–400 nanometers, shorter than that of visible light, but longer than X-rays. UV radiation is present in sunlight, and constitutes about 10% of the total electromagnetic radiation output from the Sun. It is also produced by electric arcs, Cherenkov radiation, and specialized lights, such as mercury-vapor lamps, tanning lamps, and black lights.

<span class="mw-page-title-main">Laser diode</span> Semiconductor laser

A laser diode is a semiconductor device similar to a light-emitting diode in which a diode pumped directly with electrical current can create lasing conditions at the diode's junction.

<span class="mw-page-title-main">Transparency and translucency</span> Property of an object or substance to transmit light with minimal scattering

In the field of optics, transparency is the physical property of allowing light to pass through the material without appreciable scattering of light. On a macroscopic scale, the photons can be said to follow Snell's law. Translucency allows light to pass through but does not necessarily follow Snell's law; the photons can be scattered at either of the two interfaces, or internally, where there is a change in the index of refraction. In other words, a translucent material is made up of components with different indices of refraction. A transparent material is made up of components with a uniform index of refraction. Transparent materials appear clear, with the overall appearance of one color, or any combination leading up to a brilliant spectrum of every color. The opposite property of translucency is opacity. Other categories of visual appearance, related to the perception of regular or diffuse reflection and transmission of light, have been organized under the concept of cesia in an order system with three variables, including transparency, translucency and opacity among the involved aspects.

<span class="mw-page-title-main">Laser cutting</span> Technology that uses a laser to cut materials

Laser cutting is a technology that uses a laser to vaporize materials, resulting in a cut edge. While typically used for industrial manufacturing applications, it is now used by schools, small businesses, architecture, and hobbyists. Laser cutting works by directing the output of a high-power laser most commonly through optics. The laser optics and CNC are used to direct the laser beam to the material. A commercial laser for cutting materials uses a motion control system to follow a CNC or G-code of the pattern to be cut onto the material. The focused laser beam is directed at the material, which then either melts, burns, vaporizes away, or is blown away by a jet of gas, leaving an edge with a high-quality surface finish.

<span class="mw-page-title-main">Laser engraving</span> Engraving objects using lasers

Laser engraving is the practice of using lasers to engrave an object. The engraving process renders a design by physically cutting into the object to remove material. The technique does not involve the use of inks or tool bits that contact the engraving surface and wear out, giving it an advantage over alternative marking technologies, where inks or bit heads have to be replaced regularly.

A diode-pumped solid-state laser (DPSSL) is a solid-state laser made by pumping a solid gain medium, for example, a ruby or a neodymium-doped YAG crystal, with a laser diode.

<span class="mw-page-title-main">Plastic welding</span> Welding of semi-finished plastic materials

Plastic welding is welding for semi-finished plastic materials, and is described in ISO 472 as a process of uniting softened surfaces of materials, generally with the aid of heat. Welding of thermoplastics is accomplished in three sequential stages, namely surface preparation, application of heat and pressure, and cooling. Numerous welding methods have been developed for the joining of semi-finished plastic materials. Based on the mechanism of heat generation at the welding interface, welding methods for thermoplastics can be classified as external and internal heating methods, as shown in Fig 1.

<span class="mw-page-title-main">Transparent ceramics</span> Ceramic materials that are optically transparent

Many ceramic materials, both glassy and crystalline, have found use as optically transparent materials in various forms from bulk solid-state components to high surface area forms such as thin films, coatings, and fibers. Such devices have found widespread use for various applications in the electro-optical field including: optical fibers for guided lightwave transmission, optical switches, laser amplifiers and lenses, hosts for solid-state lasers and optical window materials for gas lasers, and infrared (IR) heat seeking devices for missile guidance systems and IR night vision. In commercial and general knowledge domains, it is commonly accepted that transparent ceramics or ceramic glass are varieties of strengthened glass, such as those used for the screen glass on an iPhone.

<span class="mw-page-title-main">Laser beam welding</span> Welding technique

Laser beam welding (LBW) is a welding technique used to join pieces of metal or thermoplastics through the use of a laser. The beam provides a concentrated heat source, allowing for narrow, deep welds and high welding rates. The process is frequently used in high volume and precision requiring applications using automation, as in the automotive and aeronautics industries. It is based on keyhole or penetration mode welding.

<span class="mw-page-title-main">Yttrium aluminium garnet</span> Synthetic crystalline material of the garnet group

Yttrium aluminium garnet (YAG, Y3Al5O12) is a synthetic crystalline material of the garnet group. It is a cubic yttrium aluminium oxide phase, with other examples being YAlO3 (YAP) in a hexagonal or an orthorhombic, perovskite-like form, and the monoclinic Y4Al2O9 (YAM).

Laser-hybrid welding is a type of welding process that combines the principles of laser beam welding and arc welding.

This is a list of acronyms and other initialisms used in laser physics and laser applications.

Laser surgery is a type of surgery that uses a laser to cut tissue.

Polymer engineering is generally an engineering field that designs, analyses, and modifies polymer materials. Polymer engineering covers aspects of the petrochemical industry, polymerization, structure and characterization of polymers, properties of polymers, compounding and processing of polymers and description of major polymers, structure property relations and applications.

Infrared lamps are electrical devices which emit infrared radiation. Infrared lamps are commonly used in radiant heating for industrial processes and building heating. Infrared LEDs are used for communication over optical fibers and in remote control devices. Infrared lamps are also used for some night vision devices where visible light would be objectionable. Infrared lamp sources are used in certain scientific and industrial instrument for chemical analysis of liquids and gases; for example, the pollutant sulfur dioxide in air can be measured using its infrared absorption characteristics. IR radiant energy emitted by lamps cover a wide spectrum of wavelengths, ranging from 0.7 μm (micrometers) to a longer wavelength of 400 μm.

Laser guided and stabilized welding (LGS-welding) is a process in which a laser beam irradiates an electrical heated plasma arc to set a path of increased conductivity. Therefore, the arc's energy can be spatial directed and the plasma burns more stable. The process must be distinguished from laser-hybrid welding, since only low power laser energy of a couple hundred Watts is used and the laser does not contribute significantly to the welding process in terms of energy input.

Advanced thermoplastic composites (ACM) have a high strength fibres held together by a thermoplastic matrix. Advanced thermoplastic composites are becoming more widely used in the aerospace, marine, automotive and energy industry. This is due to the decreasing cost and superior strength to weight ratios, over metallic parts. Advance thermoplastic composite have excellent damage tolerance, corrosion resistant, high fracture toughness, high impact resistance, good fatigue resistance, low storage cost, and infinite shelf life. Thermoplastic composites also have the ability to be formed and reformed, repaired and fusion welded.

IR welding is a welding technique that uses a non-contact heating method to melt and fuse thermoplastic parts together using the energy from infrared radiation. The process was first developed in the late 1900s, but due to the high capital cost of IR equipment the process was not commonly applied in industry until prices dropped in the 1990s. IR welding typically uses a range of wavelengths from 800 to 11,000 nm on the electromagnetic spectrum to heat, melt, and fuse the interface between two plastic parts through the absorption and conversion of the IR energy into heat. Laser welding is a similar joining process that applies IR radiation at a single wavelength.

References

  1. 1 2 3 4 5 6 7 8 9 Tres, Paul A. (2017). "Welding Techniques for Plastics". Designing Plastic Parts for Assembly (eighth ed.). München: HANSER. pp. 85–168. doi:10.3139/9781569906699.005. ISBN   978-1-56990-668-2.
  2. 1 2 3 4 A. Hilton, Paul; A. Jones, I; Kennish, Y (2003-01-01). "Transmission laser welding of plastics". In Miyamoto, Isamu; Kobayashi, Kojiro F; Sugioka, Koji; Poprawe, Reinhart; Helvajian, Henry (eds.). First International Symposium on High-Power Laser Macroprocessing. Vol. 4831. p. 44. Bibcode:2003SPIE.4831...44H. doi:10.1117/12.486499. S2CID   136720521.{{cite book}}: |journal= ignored (help)
  3. 1 2 3 4 5 6 7 8 9 Troughton, Michael J. (2008). Handbook of Plastic Joining - A Practical Guide. William Andrew Publishing. ISBN   9781884207174.
  4. 1 2 Ruotsalainen, Saara; Laakso, Petri; Kujanpää, Veli (2015-01-01). "Laser Welding of Transparent Polymers by Using Quasi-simultaneous Beam Off-setting Scanning Technique". Physics Procedia. 78: 272–284. Bibcode:2015PhPro..78..272R. doi: 10.1016/j.phpro.2015.11.038 . ISSN   1875-3892.
  5. 1 2 3 4 5 6 7 8 9 10 11 12 13 Grewell, GA; Benatar, Avraham; Park, Joon (2003). Plastics and Composites Welding Handbook. München: HANSER. pp. 271–311.
  6. 1 2 3 4 PDL Staff (1997). "Laser Welding". Handbook of Plastics Joining. Plastics Design Library. pp. 101–104. doi:10.1016/B978-188420717-4.50015-4. ISBN   9781884207174.
  7. 1 2 3 Acherjee, Bappa; Kuar, Arunanshu S.; Mitra, Souren; Misra, Dipten (2012-04-01). "Effect of carbon black on temperature field and weld profile during laser transmission welding of polymers: A FEM study". Optics & Laser Technology. 44 (3): 514–521. Bibcode:2012OptLT..44..514A. doi:10.1016/j.optlastec.2011.08.008. ISSN   0030-3992.
  8. 1 2 3 4 5 6 7 8 9 Benatar, Avraham (2017). "Plastics Joining". Applied Plastics Engineering Handbook (second ed.). Plastics Design Library. pp. 575–591. doi:10.1016/B978-0-323-39040-8.00027-4. ISBN   9780323390408.
This page is based on this Wikipedia article
Text is available under the CC BY-SA 4.0 license; additional terms may apply.
Images, videos and audio are available under their respective licenses.