Mogador-class destroyer

Last updated
French destroyer Volta (X62) underway off Portsmouth (UK) on 8 August 1939.jpg
Volta underway off Portsmouth on 8 August 1939
Class overview
NameMogador-class destroyer
OperatorsCivil and Naval Ensign of France.svg  French Navy
Preceded by Le Fantasque class
Succeeded by T 47 class
Completed2
Lost2
General characteristics
TypeLarge destroyer
Displacement
Length137.5 m (451 ft 1 in)
Beam12.57 m (41 ft 3 in)
Draft4.74 m (15 ft 7 in)
Installed power
  • 4 × Indret boilers
  • 92,000  shp (69,000  kW)
Propulsion2 × shafts; 2 × geared steam turbines
Speed39 knots (72 km/h; 45 mph)
Range4,345  nmi (8,047 km; 5,000 mi) at 15 knots (28 km/h; 17 mph)
Complement12 officers, 226 men
Armament

The Mogador-class large destroyers (contre-torpilleurs) of the French Navy were laid down in 1935 and commissioned in 1939. They were extremely fast, very large destroyers intended to act as scouts for the two fast Dunkerque-class battleships. The design evolved from the extremely fast Le Fantasque class, being 300 tons heavier and carrying eight guns in semi-enclosed twin turrets rather than five guns in single open mounts. With their eight 138.6 mm (5.46 in) guns they approached a light cruiser in firepower.

Contents

Both Mogador and her sister Volta were present during the British attack on Mers-el-Kébir on 3 July 1940, but only Volta managed to escape to Toulon. Mogador was struck by a 15-inch (38 cm) shell in the rear hull that detonated her ready depth charges despite not actually detonating itself. This destroyed most of her stern above water, but she remained afloat and was repaired enough to be sent to Toulon on 1 November 1940 for reconstruction. Both ships were scuttled in Toulon Harbour when the Germans tried to seize them on 27 November 1942.

Design

Right-elevation line drawing of Mogador Contre-torpilleur Mogador (1939).svg
Right-elevation line drawing of Mogador

The Mogador class was authorized in the 1932 Estimates as an improved version of the Fantasque class with three new twin mounts carrying the same Canon de 138 mm Modèle 1929 gun as the earlier ships, but construction was suspended for a period while France and Italy negotiated some limits on their fleets and because the shipyards were already at full capacity. During this pause time was taken to modify the design to deal with the severe weather and conditions of the North Atlantic and to incorporate developments in propulsion technology that indicated that a larger hull could be used without any requiring any increase in weight. After a proposal for a catapult was abandoned because of insufficient reserve stability, an extra twin turret was decided upon to boost the ship's firepower. Volta was authorized in the 1934 Estimates together with the second Dunkerque-class battleship. [1]

General characteristics

Their construction was strengthened to handle the severe weather conditions of the North Atlantic as one of the requirements for their intended role as scouts and escorts for the Dunkerque-class battleships of the Force de Raid. Longitudinal construction was used throughout with frames spaced 1.8 metres (5.9 ft) apart and subdivided by twelve transverse compartments. Stress-bearing parts of the hull used 60 kg/m2 grade steel while the remainder of the hull used 50 kg/m2 grade steel. To save weight all internal partitions used Duralumin as did the sides of the superstructure. The hull was entirely riveted, but all other joints were welded. Despite these efforts, top-weight was higher than on earlier classes of contre-torpilleurs because of the weight of the twin-gun turrets. [2]

Accommodations were even more cramped and poorly ventilated than earlier ships because the ammunition hoists passed through the crew spaces, a problem for ships intended for long-endurance sorties into the North Atlantic. The lack of room in the hull forced a number of workshops and offices into the superstructure which added more weight high in the ship. There were three deckhouses abaft the break in the forecastle with intervals between them to permit the beam torpedo tubes to rotate, but these were no larger than in earlier ships which meant that space was at a premium. [2]

The ships proved to be excellent sea-boats and were very capable in high seas as they could sustain 34 knots (63 km/h; 39 mph) in Sea State 4. "They were very steady ships, with a gentle roll period of seven seconds; they heeled only 2-3° with a strong cross-wind, and at only 7-8° at full rudder — a marked improvement over earlier contre-torpilleurs. Their comparatively high length to beam ratio, however, gave them a high coefficient of inertia, which made maneuvers in formation difficult." [3]

Propulsion

Schema of machinery Contre-torpilleur-Mogador-schema-of-machinery-EN.svg
Schema of machinery

The Mogador-class ships retained the unit arrangement of their propulsion spaces used in earlier contre-torpilleurs. They used a new high-pressure Indret boiler rated at 3,500 kilopascals (510 psi). While this gave more power for its weight and size, it proved to be fragile and difficult to maintain. Each set of Rateau-Bretagne geared turbines was rated at 46,000 shaft horsepower (34,000 kW) and consisted of four main turbines, a high-pressure, a medium-pressure and two low-pressure with a reversing turbine in each of the main low-pressure turbine cases. There were also two small cruise turbines operating in parallel in each engine room. At low speeds, steam was directed to the cruise turbines, but at higher speeds it was diverted to the high-pressure turbine. At 25 knots (46 km/h; 29 mph) the cruise turbines were decoupled entirely using a Vulcan clutch. This didn't work properly and several ship's captains recommended that the cruise turbines be deleted from future classes entirely. Each of the two shafts was driven by single reduction gearing. The port shaft was driven by the rear engine room and was significantly shorter than the starboard shaft which was driven by the forward engine room. This caused a significant disparity between the turning circle, depending on which direction the ship was turning. [4]

Each shaft drove a three-bladed screw propeller that was 3.94 m (12.9 ft) in diameter. They suffered from severe cavitation at speed. The single semi-balanced rudder was chosen to reduce high speed resistance. It had an area of only 14.95 square metres (160.9 sq ft) and was moved by a weak steam-driven servomotor. On trials, the turning circle was measured at 800–850 metres (870–930 yd) at 25 knots (46 km/h; 29 mph). In service it took 25–30 seconds to turn the rudder to its maximum 32° at speed and the ship's turning circle was approximately double that demonstrated on trials. The ships were so unhandy that the captain of the Volta cautioned in his log that "great care was needed when operating in company with the battleship Strasbourg , because the latter ship was far more maneuverable." [5]

The Mogador-class ships were designed for a speed of 39 knots (72 km/h; 45 mph), but this was comfortably exceeded on trials when Mogador achieved a top speed of 43.45 knots (80.47 km/h; 50.00 mph) from 118,320 shp (88,230 kW) for one hour. This was at "Washington" standard displacement so her earlier performance of 41.67 knots (77.17 km/h; 47.95 mph) with 108,424 shp (80,852 kW) at a load displacement of 3,731 tonnes (3,672 long tons; 4,113 short tons) was even more impressive. [5]

At normal displacement they carried only 120 tonnes (120 long tons; 130 short tons) of oil, but carried 360 tonnes (350 long tons; 400 short tons) of oil at normal load and 710 tonnes (700 long tons; 780 short tons) at deep load. Endurance was estimated during their trials at 4,345 nautical miles (8,047 km; 5,000 mi) at a speed of 15 knots (28 km/h; 17 mph) using the cruise turbines and 2,664 nmi (4,934 km; 3,066 mi) at a speed of 24 knots (44 km/h; 28 mph) with the main turbines. This was never attained during service because the consumption by the auxiliary machinery was underestimated. [5]

Arguably the greatest weakness of these ships lay in their inability to generate sufficient electric current to power the multitude of auxiliary motors on which their advanced machinery and complex gun mountings were dependent. Their DC electrical supply was only 115 V, whereas larger cruisers with power-operated turrets had a 230 V system. Electrical power was generated by two Alsthom turbo-generators rated at only 120 kW with two small diesel generators rated at 44/52 kW for use when the ship was alongside. The latter provided only for the ship's minimum lighting and electricity needs, and fires had to be lit in at least one of the boilers in order to train the turrets or elevate the guns for practice or maintenance. Many of the auxiliary motors themselves were also seriously underpowered, particularly the servomotors for the gun mountings (which were slow to train and elevate) and for the rudder which contributed to the ship's poor maneuverability. In technological terms Mogador and Volta were ships with the armament of a light cruiser in the hull of a destroyer; the contre-torpilleur as a type had been pushed past the limits of its capabilities.

–Jordan, The Contre-Torpilleurs of the Mogador Class, p. 59

Armament

Main guns

The Mogador-class ships were designed to use four newly designed twin-gun Modèle 1934 "pseudo-turrets" that used the same Canon de 138 mm Modèle 1929 as the preceding Le Fantasque-class destroyers. The guns were housed in separate cradles that could be coupled together and could elevate to a maximum of 30° and depress 10°. The underpowered electric motors gave a maximum training speed of 10° per second and a maximum elevating speed of 14° per second. The motors were initially installed within the mountings, but were moved to the outer sides of the turrets to free up room inside the turrets. [6]

The pusher-type ammunition hoists ran up a fixed shaft in the center of the mount. The shells and their powder charges were transferred to a tipping drum that was rotated to match the bearing angle of the guns and then loaded. This system was adapted from that used for the fixed 130-millimeter (5.1 in) ammunition used in the Hardi-class destroyers. Unfortunately it was not well suited for separate-loading ammunition. Each gun had its own separate shell and powder hoist, for a total of four hoists. The tipping drum had four matching separate trays to move the ammunition to the gun. Each shell was power-rammed, but the propellant charges had to be hand-rammed. Theoretically the guns could be loaded at any angle, but the power rammer was so weak that it could not ram shells at angles above 10°. This problem, coupled with the "poor quality of manufacture of the guns, the unsatisfactory profile of the breech, resulted in a firing cycle of only 3-4 rounds per minute during the early trials with jams and failures frequent", rather than the planned 10 rounds per minute. A further problem was that there only two loaders assigned to the gun crew; they tired quickly during prolonged firing. [7]

Gunnery trials were conducted when Volta was on her sea trials in mid-1939 and were "an unmitigated disaster" for the reasons given above. Some fixes were identified, notably modifications to the breech, installation of split loading trays and reinforcement of the catapult rammers, but they had to wait until the ships' next refit to be implemented. But even these modifications were only stop gaps and an entirely new loading system was deemed necessary, but since this was expected to take 10–12 months to develop the current system would have to be used in the meantime. Both Volta and Mogador were refitted in January 1940 and had their turrets modified, although loading still could not be done at angles higher than 10°. The surrender of France in June 1940 ended any work on a new loading system. [8] Five-round ready racks for each gun were added to the sides of the turrets during the refit to compensate for any problems with the loading systems. [6] The magazines were designed to store 1440 138 mm shells, 180 rounds per gun, plus there was a separate magazine for 85 starshells which supplied turret Nr. 2. [9]

Anti-aircraft suite

A single 37-millimeter (1.5 in) twin-gun Modèle 1933 anti-aircraft mount was installed on the rearmost deckhouse forward of turret Nr. 3. It used the 50-caliber semi-automatic 37 mm (1.5 in) gun. It had a conventional sliding breech and used six-round cartridge boxes which gave it a maximum rate of fire of only 30-40 rounds per minute. This mount was used in lieu of the intended power-driven Modèle 1935 twin-gun mount which was to use a new 48-caliber, fully automatic 37 mm gun that was expected to be able to fire at a rate of 165 rounds per minute, but the new gun was still in development when the ships were commissioned. [10] 250 rounds were stored near the mount, but the main magazine, which held an additional 1,250 rounds, was adjacent to the forward 138 mm magazines. This required a loader to move forward 50 metres (55 yd) to pick up each 12.8-kilogram (28 lb) cartridge box and carry it back to the waiting gun crew. [9]

Two twin 13.2-millimeter (0.52 in) Hotchkiss machine gun mounts were fitted as anti-strafing weapons. These had a high rate of fire at 450 rpm, but this was hampered by the awkward 30-round magazine feed. Initially they were mounted on each side of the forward superstructure at deck level and fitted with gun shields to protect them against the spray. Trials revealed the limitations of these positions with poor arcs of fire and the gun shields obstructed the aimer's view of the target. Following the completion of the trials the guns were relocated to a new deckhouse between the bridge and turret Nr. 2 and their gun shields removed. 2500 rounds per barrel were stored in the forward magazines. [9]

Underwater weapons

The Mogador-class ships were designed for anti-surface warfare rather than anti-submarine work and they were given a large torpedo battery in consequence. Two triple Modèle 1928T torpedo launchers were fitted on each beam between the funnels and two twin Modèle 1928D launchers were located on the beam, abaft the second funnel. The placement of each launcher on the beam significantly increased each launcher's arc of fire (25° to 150°) in comparison to the Le Fantastaque's centerline mount (60°-100°). However this was not without cost as her torpedo broadside was weaker by one tube than the older class, but the extra launchers positioned close to the ship's side imposed, more importantly, a weight and stability penalty. [11]

All of her mounts used the 550-millimeter (22 in)Modèle 1923DT torpedo with a 308 kg (679 lb) warhead. This 2,068 kg (4,559 lb) torpedo used a four-cylinder, radial Brotherhood alcohol engine to power it at two set speeds. The fast speed was 39 knots (72 km/h; 45 mph) to a range of 9,000 metres (9,800 yd) while the slow speed setting was 35 knots (65 km/h; 40 mph) to a range of 13,000 metres (14,000 yd). [11]

Twin depth charge tunnels were built into the rear hull of the Mogador-class ships. Each tunnel housed eight Guirard depth charges, with another sixteen stowed in the rear magazine. They were launched by remote control in patterns of four using a chain system. Since no sonar equipment was fitted these depth charges were unlikely to actually damage a submarine. [11]

Fixed pairs of mine rails were mounted above the stern and each pair could carry five Bréguet B4 mines. These could be extended using removable section stowed between decks to carry another thirty mines if necessary. [11]

Fire control

The centralized fire-control system was similar to that of the Le Fantasque-class with 12 × 72 target-designation binoculars on each side of the bridge linked by Granat transmitters to the directors located atop the bridge and abaft the second funnel. Each director had a 5-metre (16 ft 5 in) OPL Modèle 1935 stereoscopic rangefinder and sent the range to the post central artillerie where it was fed into a modernized Modèle 1929 electro-mechanical computer which calculated the firing solution and transmitted it to the turrets. The turrets could also be controlled locally if necessary. [9]

The torpedo-control system was much the same, although entirely separate from the gunnery system. 8 × 30 target-designation binoculars were mounted on each side of the bridge and transmitted the target's bearing to the torpedo director located above the primary gunnery director above the bridge. It used a separate 5-metre OPL Modèle 1935 stereoscopic rangefinder to provide the bearing and range to a Modèle 1933 electro-mechanical computer which calculated the torpedo firing angle. This was sent to the remotely controlled torpedo tubes, and the command to fire could be given by either the torpedo director or either of the secondary positions on the wings of the bridge. [11]

Construction

This class only consisted of Mogador (X61) and Volta (X62). Steel was cut on both contre-torpilleurs beginning in late 1934, Mogador at the Arsenal de Lorient and Volta at At. & Ch. de Bretagne, Nantes, although assembly did not begin until the autumn of the following year. Industrial unrest disrupted their construction and it was not until January 1938 that Mogador was handed over to the French Navy for sea trials. Volta followed three months later. [12] However, neither ship was formally accepted by the French Navy for another year. Mogador was not commissioned (clotûre d'armament) until 8 April 1939 and Volta on 6 March 1939. [13]

Four improved Mogador-class ships were ordered in 1939 to be named Kléber, Desaix, Hoche and Marceau, but their construction was suspended due to the start of World War II. Their design was continually modified in light of wartime experience, but the original plan for dual-purpose 130 mm (5.1 in) guns had to be shelved when it became apparent that they could not be developed in a timely manner, and they reverted to the main armament of the Mogadors. The anti-aircraft armament was reinforced with the substitution of four 100 mm (3.9 in) anti-aircraft guns for the single twin 37 mm mount. But these plans came to nought when France surrendered in June 1940. [14]

History

Mogador damaged at Mers-el-Kebir after being hit in the rear hull Mogador 03-07-1940.jpg
Mogador damaged at Mers-el-Kébir after being hit in the rear hull

Mogador and Volta comprised the 6th Large Destroyer Division (6e Division de contre-torpilleurs) and were assigned to the Force de Raid based at Brest when the war began. This group's purpose was to hunt German blockade runners and raiders and to escort convoys that might be in danger from the same. From 21 to 30 October 1939 the Force de Raid escorted the KJ.4 convoy to protect it against the German cruiser Deutschland which had sortied into the North Atlantic before the war began. A sortie by the German battleships Gneisenau and Scharnhorst into the North Atlantic on 21 November prompted the Force de Raid to sail from Brest to rendezvous with the British battlecruiser HMS Hood and patrol the area south of Iceland, but the German ships were able to return safely under the cover of heavy weather without being engaged. [15]

Both ships were refitted in early 1940 and a number of minor changes were made. The necessary improvements identified for the main armament during their sea trials a year earlier were finally implemented, the canvas cover for the back of the turrets was replaced by a rolling door, new radios were installed, and shields were fitted to the anti-aircraft machine guns and the searchlights. A SS-6 sonar was fitted in June 1940, but proved to be ineffectual. [16]

During the British attack on Mers-el-Kébir on 3 July 1940, Mogador was severely damaged by a hit from a 15-inch (38 cm) shell in the rear hull that detonated her ready depth charges. Volta was also present, but managed to escape in company with the battleship Strasbourg and other ships. Mogador was repaired enough to reach Toulon several months later, but was still undergoing repairs and modifications in Toulon in November 1942. Both Mogador and Volta were scuttled in Toulon Harbour on 27 November 1942 to prevent their capture by Germany. Both were refloated in 1943 by the Italians, but neither was repaired and both were eventually broken up. [17]

Notes

  1. Jordan, pp. 46–49
  2. 1 2 Jordan, p. 49
  3. Jordan p. 55
  4. Jordan, pp. 49–50
  5. 1 2 3 Jordan, p. 50
  6. 1 2 "French 138.6 mm/45 (5.46") Models 1929 and 1934". 14 October 2007. Archived from the original on 25 June 2009. Retrieved 2009-06-25.
  7. Jordan, p. 51
  8. Jordan, p. 55
  9. 1 2 3 4 Jordan, p. 52
  10. Campbell, John (2002). Naval Weapons of World War Two. London: Conway Maritime Press. p. 308. ISBN   0-87021-459-4.
  11. 1 2 3 4 5 Jordan, p. 53
  12. Jordan, pp. 49, 54
  13. Whitley, p. 44
  14. Whitley, p. 46
  15. Rohwer, pp. 7, 9
  16. Jordan, pp. 55–57, 60
  17. Whitley, p. 45

Related Research Articles

<i>Le Fantasque</i>-class destroyer

The Le Fantasque class of six large, very fast destroyers was ordered under the French naval programme of 1930. They served in World War II for both Vichy France and the Free French Forces.

<i>Chacal</i>-class destroyer French destroyer class

The Chacal-class destroyer, sometimes known as the Jaguar class, were a group of six large destroyers (contre-torpilleurs) built for the French Navy during the 1920s. Their primary role was scouting for the battleline. All were named for predators: Chacal means jackal, and the other five were named for big cats.

<i>Vauquelin</i>-class destroyer French destroyer class

The Vauquelin class was a group of six large destroyers built for the French Navy in the early 1930s. Entering service in 1933–1934, the sister ships spent most of their careers in the Mediterranean. During the Spanish Civil War of 1936–1939, they helped to enforce the non-intervention agreement. When France declared war on Germany in September 1939, all of the Vauquelins were assigned to the High Sea Forces which was tasked to escort French convoys and support the other commands as needed. Three of the sisters briefly deployed to Scotland in early 1940 to support the Allied forces in the Norwegian Campaign and Maillé Brézé was lost to an accidental explosion. The others returned to the Mediterranean in time to participate in Operation Vado, a bombardment of Italian coastal facilities after Italy entered the war in June.

The Le Hardi class consisted of twelve destroyers built for the Marine Nationale during the late 1930s. Only seven ships were ultimately completed while construction of the remaining five ships was interrupted by the French defeat in the Battle of France in May–June 1940 and were never finished. The seven ships that were seaworthy sailed for French North Africa to prevent their capture by the advancing Germans. Several ships later sailed for French West Africa where Le Hardi played a minor role in the Battle of Dakar in September. The Germans captured two ships that were still under construction and attempted to finish them both before abandoning the effort in 1943.

<span class="mw-page-title-main">Canon de 138 mm Modèle 1929</span> Naval gun

The Canon de 138 mm Modèle 1929 was a medium-calibre naval gun of the French Navy used during World War II. It was used on the large destroyers (contre-torpilleurs) of the Le Fantasque and Mogador classes.

Volta was a Mogador-class destroyer of the French Navy. Named for the West African river, she was built before the outbreak of World War II and was the penultimate contre-torpilleur built by the French Navy. Along with her sister ship Mogador, Volta was designed in an effort to build a ship capable of out-fighting every other ship below her tonnage. Arguably the design was less than successful, as it possessed the armament of a light cruiser on the hull of a destroyer. The two ships of the class have been described as having pushed the contre-torpilleur concept beyond "the limits of its capabilities".

French destroyer <i>Mogador</i> Mogador-class destroyer

Mogador was the lead ship of the French Navy's Mogador class of destroyers. Named after the Moroccan town, she was built before the outbreak of World War II. The ship was heavily damaged during the British attack on Mers-el-Kébir on 3 July 1940, but was later repaired and sailed to Toulon. She was scuttled in Toulon Harbor when the Germans tried to seize her, along with the rest of the fleet, on 27 November 1942.

French destroyer <i>Lynx</i> French Chacal-class destroyer

The French destroyer Lynx was a Chacal-class destroyer (contre-torpilleur) built for the French Navy during the 1920s. The Chacals were regarded as obsolete by 1935 and Lynx became a training ship for the torpedo school at Toulon that year. She was assigned convoy escort duties in the Atlantic after the start of World War II in September 1939. In July 1940, the ship was present when the British attacked the French ships at Mers-el-Kébir, but managed to escape without damage. After she reached Toulon, Lynx was placed in reserve where she remained for the next two years. On 27 November 1942, she was scuttled at Toulon when the Germans attempted to capture the French ships there. Her wreck was salvaged in 1944, but she was not broken up until 1948.

French destroyer <i>LIndomptable</i> French Le Fantasque-class large destroyer

L'Indomptable was one of six Le Fantasque-class large destroyers built for the Marine Nationale during the 1930s. The ship entered service in 1935 and participated in the Second World War. When war was declared in September 1939, all of the Le Fantasques were assigned to the Force de Raid which was tasked to hunt down German commerce raiders and blockade runners. L'Indomptable made one sortie into the Skaggerak in April 1940 and was then transferred to French Algeria in late April 1940 in case Italy decided to enter the war. She screened French cruisers several times as they unsuccessfully hunted for Italian ships after Italy declared war in June.

Le Hardi was the lead ship of her class of destroyers built for the Marine Nationale during the late 1930s. The ship was completed during the Battle of France in mid-1940 and her first mission was to help escort an incomplete battleship to French Morocco only days before the French signed an armistice with the Germans. She played a minor role in the Battle of Dakar in September, mostly laying smoke screens. Le Hardi helped to escort one of the battleships damaged by the British during their July attack on Mers-el-Kébir, French Algeria, back to France in November. She was reduced to reserve in mid-1942.

French destroyer <i>Simoun</i> Destroyer of the French Navy

Simoun was a Bourrasque-class destroyer built for the French Navy during the 1920s.

French destroyer <i>Orage</i> Destroyer of the French Navy

Orage was a Bourrasque-class destroyer built for the French Navy during the 1920s. The ship was sunk in 1940.

French destroyer <i>Tempête</i> Destroyer of the French Navy

Tempête was a Bourrasque-class destroyer built for the French Navy during the 1920s.

Fleuret was one of a dozen Le Hardi-class destroyers built for the Marine Nationale during the late 1930s. The ship was completed during the Battle of France in mid-1940 and her first mission was to help escort a battleship to Dakar, French West Africa, only days before the French signed an armistice with the Germans. After the British attack on Dakar in September, she was one of four destroyers ordered to attack British shipping, although there was only an inconclusive duel with a British destroyer. Fleuret helped to escort one of the battleships damaged by the British during their July attack on Mers-el-Kébir, French Algeria, back to France in November and was then reduced to reserve.

The French destroyer Épée was one of a dozen Le Hardi-class destroyers built for the French Navy during the late 1930s. The ship was completed during the Battle of France in mid-1940 and her first mission was to help escort an incomplete battleship to French Morocco only days before the French signed an armistice with the Germans. After the British attack on Dakar in September, she was one of four destroyers ordered to attack British shipping, although there was only an inconclusive duel with a British destroyer. Épée helped to escort one of the battleships damaged by the British during their July Attack on Mers-el-Kébir, French Algeria, back to France in November. She was transferred back to French Morocco in May 1941 for convoy-escort duties that lasted until October.

Mameluk was one of a dozen Le Hardi-class destroyers built for the French Navy during the late 1930s. The ship was completed during the Battle of France in mid-1940 and her first mission was to help escort an incomplete battleship to French Morocco only days before the French signed an armistice with the Germans in June. She then helped to escort one of the battleships damaged by the British during their July attack on Mers-el-Kébir, French Algeria, back to France in November. Mameluk returned to Morocco in early 1941 for convoy-escort duties and then was transferred back to France in late 1941.

The French destroyer Casque was one of a dozen Le Hardi-class destroyers built for the French Navy during the late 1930s. The ship was completed during the Battle of France in mid-1940 only days before the French signed an armistice with the Germans. When the Germans occupied Vichy France after the Allies landed in French North Africa in November 1942 and tried to seize the French fleet intact, the destroyer was one of the ships scuttled to prevent their capture. The Regia Marina attempted to salvage her in 1943, but the effort was abandoned the following year. The ship was refloated in 1948 and scrapped.

The French destroyer Le Flibustier was one of a dozen Le Hardi-class destroyers built for the French Navy during the late 1930s. Still incomplete when the French signed an armistice to end the Battle of France, material shortages prevented her completion and she was placed in reserve. The ship was renamed Bison in early 1941. When the Germans occupied Vichy France after the Allies landed in French North Africa in November 1942 and tried to seize the French fleet intact, the destroyer was one of the few ships not scuttled to prevent their capture. She was turned over to the Regia Marina in 1943, but was seized by the Germans after the Italian armistice in September. The ship was salvaged in 1945 and later scrapped.

The French destroyer Lansquenet was one of a dozen Le Hardi-class destroyers built for the French Navy during the late 1930s. Placed into service after the French signed an armistice with the Germans in June 1940, she sailed to French Morocco to avoid capture. In November the ship helped to escort one of the battleships damaged by the British during their July attack on Mers-el-Kébir, French Algeria, back to France. Placed in reserve afterwards, she was scuttled to prevent her capture when the Germans occupied Vichy France in November 1942. Lansquenet was salvaged in 1943 by the Regia Marina and captured by the Germans after the Italian armistice in September. They scuttled the ship in Italy in 1945; she was refloated in 1946, but was never repaired. She was stricken in 1958, then scrapped.

Siroco was one of a dozen Le Hardi-class destroyers built for the French Navy during the late 1930s under the name Le Corsaire. Although she was still under construction during the Battle of France, the ship sailed to French Algeria to avoid capture by the Germans. She was renamed Siroco in early 1941 while still under construction and was completed later that year and immediately placed in reserve. The destroyer was one of the ships scuttled to prevent their capture in November 1942 when the Germans occupied Vichy France. Siroco was salvaged by the Regia Marina and towed to Italy in 1943. Captured by the Germans after the Italian armistice in September, the ship was scuttled by the Germans in late 1944 and later scrapped.

References