Radial (radio)

Last updated March 18, 2023

In RF engineering, radial has three distinct meanings, both referring to lines which radiate from (or intersect at) a radio antenna, but neither meaning is related to the other.

When used in the context of antenna construction, radial wires are physical objects: Wires running away from the base of the antenna, used to augment or replace the conductivity of the ground near the base of the antenna. The radial wires either may run above the surface of the earth (elevated radials), on the surface (on ground radials), or buried a centimeter or so under the earth (buried radials). The ends of the wires nearest the antenna base are connected to the antenna system electrical ground, and the far ends are either unconnected, or connected to metal stakes driven into the earth.

Top loading radial wires

Symmetrically arranged radial wires may also be attached to the top of an antenna, running horizontally away from its apex. For practical length radials, their effect is to improve feedpoint impedance of a short antenna almost the same as extending the height of the antenna by an amount equal to the combined length of all the radials, up to a point of diminishing returns around about a dozen radials. The radials do not themselves radiate, but may indirectly cause a small improvement in antenna radiation of short antennas by raising their point of maximum current upward along the main part of the mast.

Map radial lines

When used in the context of planning for a transmission system, radial lines are a concept used when describing a radio station's broadcast range: The radials in this case are several lines drawn on a map, radiating from the transmitter, with evenly spaced horizontal bearings. The radial extends as far as the transmitted signal can reach either by calculation or by measurement.

Ground system radial wires

Stations transmitting at low frequencies like the mediumwave and longwave AM broadcast bands, and some lower shortwave frequencies, have frequencies so low that any feasible antenna is necessarily short compared to the wavelength, the most common being a quarter wave vertical antenna. These wires are called radials, ground radials, grounding radials, ground system radials, or earthing radials.

The radials at the antenna base provide a proper ground plane for the types of radio antennas used for long wavelengths. These "half dipole" antennas require grounding or earthing wires in order to function well, since the virtual image of the antenna electrically reflected by the mirror-like ground system is an essential part of the operation of the actual antenna standing above the ground system. The radials are typically buried in the soil or laid on the soil in a flat, radial pattern.

Practical issues for ground system radials

The ground system radials do not have to be absolutely straight nor absolutely horizontal. Although they provide an electrical "ground", they do not require any actual contact with the surrounding earth, even though advisable.

When the radials are mechanically incorporated into the structure of a small antenna it is called a ground plane antenna . For these antennas the radials slope off at an angle and are also called a skirt.

Radials lying upon the ground or within it are not resonant, and there is a great deal of practical latitude in the length and number of radials, although licensing requirements may demand excessive numbers and lengths.^{[lower-alpha 1]} Elevated radials are far more efficient at intercepting electrical fields before they reach the earth, so that only three or four may suffice, but since their electrical properties are not dampended by adjacent soil they must be cut to a resonant length.

Electrical hazards

When well designed, the far ends of the wires in the ground system carry extremely high voltages. If elevated above the soil, the ends are often connected to ground rods as a safety measure, rather than to improve the function of the antenna. Because of the same hazard, elevated radials are placed at least eight feet above the ground surface, to be out of reach of passers by, or over a fenced area.

Any metal object within the near field of the radiator must also be directly tied to the ground system, or the metal will become charged with radio-frequency voltage, and become an electric shock hazard. If large enough to act as a parasitic radiator it may also affect or distort the antenna radiation pattern.^{[lower-alpha 2]}

Top loading radial wires

Similar radial wires can be placed on the top of antennas (instead of at the base) that also promote more efficient distribution of current in the antenna, but the structure of radial wires added to the top end of the antenna is called a capacitance hat or top loading. Like ground radials, top radials are symmetrically arranged wires placed to radiate away from the apex of the antenna, ideally running horizontally away from the top. Electrically, this is equivalent to attaching a capacitor at the top of the antenna, whose other contact is wired to the ground system, which constitutes the opposite plate of the capacitor.

Top loading antennas is a way to effectively increase the height of an antenna (for some purposes, but not all) either to reduce the reactance at the feedpoint, or to indirectly increase radiation resistance by increasing the amount of current in the vertical part of the mast. Although coils can be used to similarly load an antenna, using coils introduces resistance losses from the substantial amount of wire needed; using radials for capacitive loading effectively adds no loss.

Practical considerations for loading radials

For radials 9 electrical degrees or less (1/40 wavelength, each, or shorter) the effect on feedpoint impedance and the current in the mast is the same as extending the height of the antenna by a length of wire equal to 99% of the total length of all the radials, up to about a dozen radials.^{[lower-alpha 3]} The radials may cause a small to moderate improvement in antenna radiation by raising the point of maximum current upward along the main part of the antenna, although symmetrical radials themselves do not radiate.

Horizontal radial wires are ideal, but sometimes difficult to support. As a substitute same-lengths of conductive top segments of down-sloping guy wires can be electrically connected to the antenna apex. This is less than ideal, but often more feasible for long top radials on towers. When guy wires are used for top loading instead of horizontal radial wires, they must not extend very far down the mast, since the guy wires will block some radiation from the mast, which causes a conflict between loss caused by the radiating mast being "shadowed" by the guy wires, and the indirect gains realized by the increased current in the radiating part of the mast.

Map radial lines

The use of radial lines on a map for measurement, planning, and regulation of radio transmissions is called the radial method. It has no relation to grounding radials described above.

Radials for transmission planning

In the field of transmission planning, radials are evenly spaced points (vectors) along evenly spaced lines (bearings) from a common point on a map, which are used to determine the average elevation above mean sea level (AMSL) within a radio station's broadcast range (including broadcast stations and cellphone base stations, among others).

This in turn determines the station's height above average terrain (HAAT), which greatly affects its coverage area (more so than effective radiated power), and therefore the potential for RF interference with other adjacent stations or cells. This information must be submitted with an application for a construction permit. The points used for calculation may differ if a directional antenna is used.

Background of the radial method

The use of the radial method is more common in North America, where the FCC and CRTC use it in mediumwave transmission planning and regulation. In Europe and Asia, the use of radials has fallen out of favor since the 1970s, and in many nations the radial antenna proof is only acceptable as an ancillary antenna proof. Canada and Mexico, due to lower population densities, never implemented the fully complete radial models that the US FCC did.

The radial method has been falling out of favor for methods based on Cartesian coordinates. Cartesian methods require more CPU time (and memory) to compute, but are understood to more realistically represent antenna systems. The main importance of the radial methods is that a quick antenna system proof can be completed in less than 15 minutes (often in only 5 minutes) of a typical home computer's CPU time, regardless of antenna system complexity.

Regulatory use of radials

The ITU over the past 50 years — in consideration of the various population densities of its members — officially mandates a minimum of 5 radials for an entire antenna system.

Although many broadcasting regulators around the world had to find some way of regulating longwave and mediumwave antenna patterns and power, only the FCC chose to implement the radial method in its fullest form.

The FCC decision to fully implement radials evolved from 1925 to 1975. Technology had changed, and by the 1980s, computer terrain simulation of station interference and station patterns could be done on mainframes, typically using Cartesian or other non-radial methods.

The FCC rules on radials were relaxed in stages from 1996 to 2013. It is expected that the 2013 ruleset for radials will probably endure without change for a decade.

Footnotes

↑ Longstanding US FCC regulations for AM broadcasting stations require 120 radials, each 1/4 wave long. Amateurs have found that between a third and a half that number are ample, and that the length of the radials may be 1/8 wave or shorter if there are enough of them.
↑ In one unusual case, the strip mall built around the WSB AM tower near Atlanta has every metal object (such as plumbing and ductwork) grounded for this reason.
↑ When the radials are packed together too densely, they begin to interfere with each other's electrical field lines, and reduce each other's effect. Various other shapes such as a solid ring with a few conducting spokes may be better than several radials.

Related Research Articles

<span class="mw-page-title-main">Ground (electricity)</span> Reference point in an electrical circuit from which voltages are measured

In electrical engineering, ground or earth is a reference point in an electrical circuit from which voltages are measured, a common return path for electric current, or a direct physical connection to the Earth.

Medium wave (MW) is the part of the medium frequency (MF) radio band used mainly for AM radio broadcasting. The spectrum provides about 120 channels with more limited sound quality than FM stations on the FM broadcast band. During the daytime, reception is usually limited to more local stations, though this is dependent on the signal conditions and quality of radio receiver used. Improved signal propagation at night allows the reception of much longer distance signals. This can cause increased interference because on most channels multiple transmitters operate simultaneously worldwide. In addition, amplitude modulation (AM) is often more prone to interference by various electronic devices, especially power supplies and computers. Strong transmitters cover larger areas than on the FM broadcast band but require more energy and longer antennas. Digital modes are possible but have not reached momentum yet.

Low frequency (LF) is the ITU designation for radio frequencies (RF) in the range of 30–300 kHz. Since its wavelengths range from 10–1 km, respectively, it is also known as the kilometre band or kilometre wave.

<span class="mw-page-title-main">Antenna (radio)</span> Electrical device

In radio engineering, an antenna or aerial is the interface between radio waves propagating through space and electric currents moving in metal conductors, used with a transmitter or receiver. In transmission, a radio transmitter supplies an electric current to the antenna's terminals, and the antenna radiates the energy from the current as electromagnetic waves. In reception, an antenna intercepts some of the power of a radio wave in order to produce an electric current at its terminals, that is applied to a receiver to be amplified. Antennas are essential components of all radio equipment.

Radiation resistance, $or, is proportional to the part of an antenna's feedpoint electrical resistance that is caused by power loss from the emission of radio waves from the antenna.$

In radio and telecommunications a dipole antenna or doublet is the simplest and most widely used class of antenna. The dipole is any one of a class of antennas producing a radiation pattern approximating that of an elementary electric dipole with a radiating structure supporting a line current so energized that the current has only one node at each end. A dipole antenna commonly consists of two identical conductive elements such as metal wires or rods. The driving current from the transmitter is applied, or for receiving antennas the output signal to the receiver is taken, between the two halves of the antenna. Each side of the feedline to the transmitter or receiver is connected to one of the conductors. This contrasts with a monopole antenna, which consists of a single rod or conductor with one side of the feedline connected to it, and the other side connected to some type of ground. A common example of a dipole is the "rabbit ears" television antenna found on broadcast television sets.

A whip antenna is an antenna consisting of a straight flexible wire or rod. The bottom end of the whip is connected to the radio receiver or transmitter. A whip antenna is a form of monopole antenna. The antenna is designed to be flexible so that it does not break easily, and the name is derived from the whip-like motion that it exhibits when disturbed. Whip antennas for portable radios are often made of a series of interlocking telescoping metal tubes, so they can be retracted when not in use. Longer whips, made for mounting on vehicles and structures, are made of a flexible fiberglass rod around a wire core and can be up to 11 m long.

An antenna tuner is an electronic device insered into the feedline between a radio transmitter and its antenna. Its purpose is to optimize power transfer by matching the impedance of the radio to the impedance of the end of the feedline connecting the antenna to the transmitter.

<span class="mw-page-title-main">Guy-wire</span> Tensioned cable designed to add stability to a freestanding structure

A guy-wire, guy-line, guy-rope, down guy, or stay, also called simply a guy, is a tensioned cable designed to add stability to a free-standing structure. They are used commonly for ship masts, radio masts, wind turbines, utility poles, and tents. A thin vertical mast supported by guy wires is called a guyed mast. Structures that support antennas are frequently of a lattice construction and are called "towers". One end of the guy is attached to the structure, and the other is anchored to the ground at some distance from the mast or tower base. The tension in the diagonal guy-wire, combined with the compression and buckling strength of the structure, allows the structure to withstand lateral loads such as wind or the weight of cantilevered structures. They are installed radially, usually at equal angles about the structure, in trios and quads. As the tower leans a bit due to the wind force, the increased guy tension is resolved into a compression force in the tower or mast and a lateral force that resists the wind load. For example, antenna masts are often held up by three guy-wires at 120° angles. Structures with predictable lateral loads, such as electrical utility poles, may require only a single guy-wire to offset the lateral pull of the electrical wires, at a spot where the wires change direction.

A cage antenna is a radio antenna where a conventional design has been augmented by replacing a single long conductor with several parallel wires, connected at their ends, and held in position by ring spacers or support struts mounted on a central mast. The "cage" is either mounted around a central mast or suspended from overhead wires.

Radio masts and towers are typically tall structures designed to support antennas for telecommunications and broadcasting, including television. There are two main types: guyed and self-supporting structures. They are among the tallest human-made structures. Masts are often named after the broadcasting organizations that originally built them or currently use them.

A mast radiator is a radio mast or tower in which the metal structure itself is energized and functions as an antenna. This design, first used widely in the 1930s, is commonly used for transmitting antennas operating at low frequencies, in the LF and MF bands, in particular those used for AM radio broadcasting stations. The conductive steel mast is electrically connected to the transmitter. Its base is usually mounted on a nonconductive support to insulate it from the ground. A mast radiator is a form of monopole antenna.

A ‘T’-antenna, ‘T’-aerial, or flat-top antenna is a monopole radio antenna consisting of one or more horizontal wires suspended between two supporting radio masts or buildings and insulated from them at the ends. A vertical wire is connected to the center of the horizontal wires and hangs down close to the ground, connected to the transmitter or receiver. Combined, the top and vertical sections form a ‘T’ shape, hence the name. The transmitter power is applied, or the receiver is connected, between the bottom of the vertical wire and a ground connection. ‘T’-antennas are typically used in the VLF, LF, MF, and shortwave bands, and are widely used as transmitting antennas for amateur radio stations, and long wave and medium wave AM broadcasting stations. They can also be used as receiving antennas for shortwave listening.

A loop antenna is a radio antenna consisting of a loop or coil of wire, tubing, or other electrical conductor, that is usually fed by a balanced source or feeding a balanced load. Within this physical description there are two distinct types:

A monopole antenna is a class of radio antenna consisting of a straight rod-shaped conductor, often mounted perpendicularly over some type of conductive surface, called a ground plane. The driving signal from the transmitter is applied, or for receiving antennas the output signal to the receiver is taken, between the lower end of the monopole and the ground plane. One side of the antenna feedline is attached to the lower end of the monopole, and the other side is attached to the ground plane, which is often the Earth. This contrasts with a dipole antenna which consists of two identical rod conductors, with the signal from the transmitter applied between the two halves of the antenna.

<span class="mw-page-title-main">Folded unipole antenna</span> Antenna used for radio broadcasts

The folded unipole antenna is a type of monopole mast radiator antenna used as a transmitting antenna mainly in the medium wave band for AM radio broadcasting stations. It consists of a vertical metal rod or mast mounted over and connected at its base to a grounding system consisting of buried wires. The mast is surrounded by a "skirt" of vertical wires electrically attached at or near the top of the mast. The skirt wires are connected by a metal ring near the mast base, and the feedline feeding power from the transmitter is connected between the ring and the ground.

An umbrella antenna is a capacitively top-loaded wire monopole antenna, consisting in most cases of a mast fed at the ground end, to which a number of radial wires are connected at the top, sloping downwards. They are used as transmitting antennas below 1 MHz, in the MF, LF and particularly the VLF bands, at frequencies sufficiently low that it is impractical or infeasible to build a full size quarter-wave monopole antenna. The outer end of each radial wire, sloping down from the top of the antenna, is connected by an insulator to a supporting rope or (usually) insulated cable anchored to the ground; the radial wires can also support the mast as guy wires. The radial wires make the antenna look like the wire frame of a giant umbrella hence the name.

In electronics and radio communication, a counterpoise is a network of suspended horizontal wires or cables, used as a substitute for an earth (ground) connection in a radio antenna system. It is used with radio transmitters or receivers when a normal earth ground cannot be used because of high soil resistance or when an antenna is mounted above ground level, for example, on a building. It usually consists of a single wire or network of horizontal wires, parallel to the ground, suspended above the ground under the antenna, connected to the receiver or transmitter's "ground" wire. The counterpoise functions as one plate of a large capacitor, with the conductive layers of the earth acting as the other plate.

A halo antenna, or halo, is a center-fed  1 /2 wavelength dipole antenna, which has been bent into a circle, with a break directly opposite the feed point. The dipole ends are close, but do not touch, and may be widened to form an air capacitor, whose spacing is used to adjust the antenna's resonant frequency. Most often mounted horizontally, this antenna's radiation is then approximately omnidirectional and horizontally polarized.

In radio systems, many different antenna types are used whose properties are especially crafted for particular applications. Antennas can be classified in various ways. The list below groups together antennas under common operating principles, following the way antennas are classified in many engineering textbooks.

References

This page is based on this Wikipedia article
Text is available under the CC BY-SA 4.0 license; additional terms may apply.
Images, videos and audio are available under their respective licenses.

[1] Longstanding US FCC regulations for AM broadcasting stations require 120 radials, each 1/4 wave long. Amateurs have found that between a third and a half that number are ample, and that the length of the radials may be 1/8 wave or shorter if there are enough of them.

[2] In one unusual case, the strip mall built around the WSB AM tower near Atlanta has every metal object (such as plumbing and ductwork) grounded for this reason.

[3] When the radials are packed together too densely, they begin to interfere with each other's electrical field lines, and reduce each other's effect. Various other shapes such as a solid ring with a few conducting spokes may be better than several radials.

[lower-alpha 1]

[lower-alpha 2]

[lower-alpha 3]