DEXRON is the trade name for a group of technical specifications for automatic transmission fluid (ATF) created by General Motors (GM). The name was first registered as a trademark and later evolved into a brand of GM. GM licenses the name and specifications to companies that manufacture the fluid and sell it under their own brand names. Not all DEXRON fluids are licensed by GM for reselling under another brand name. To be licensed, the product must have a license number that begins with the letters B through J and include a "DEXRON Approved" sticker on its container.[citation needed] Like many automobile manufacturers, GM uses transmissions sourced from other suppliers or transmission manufacturers around the world; many of these may use their own unique fluid.
Originally, the DEXRON name was only associated with automatic transmission fluids, though GM later released DEXRON gear oils and other lubricants under the DEXRON brand.[1]
GM Automatic Transmission Fluids (ATF)
The original DEXRON (B) transmission fluid was introduced on April 1, 1967. Over the years, the original DEXRON (B) was supplanted by DEXRON-II (C), DEXRON-II (D), DEXRON-II (E), DEXRON-III (F), DEXRON-III (G), DEXRON-III (H), DEXRON-VI (J), DEXRON HP, DEXRON LV ATF HP, and DEXRON ULV, which is the latest fluid to date. GM has upgraded the DEXRON's specifications over time. The newer fluids are not always backward-compatible with previous fluids. Newer 6, 8, 9, and 10-speed transmissions, as well as plug-in hybrid (PHEV) and electric vehicle (EV) transmission technologies, require specialized fluids to operate properly. There remains a market for older fluids that claim to meet the earlier fluid specifications. See the details below for the backward compatibility of each fluid.
Before DEXRON: 1937–1967
1937 – Motor Oil
1937–1939 Gargoyle Mobiloi, used in GM's Automatic Safety Transmission
The automatic safety transmission was first offered as an extra-cost option by the Oldsmobile Division of GM in the fall of 1937 for their Six and Eight models. It was only used during the 1938 and 1939 model years. The automatic safety transmission used the same seasonal grade of motor oil as the engine for lubrication and hydraulic functions.
The Automatic Safety Transmission was a four-speed transmission that could shift powerfully without needing a regular clutch. The transmission was called the Automatic Safety Transmission (AST) because the clutch operation was reduced to one-third of that required by a conventional transmission. The clutch was only necessary when starting or stopping the car.
The AST had two driving ranges (low and high). In low range, the transmission would shift from 1st to 2nd gear and then hold in 2nd. In high range, the transmission would start in 1st gear, jump to 3rd, then shift to 4th gear. The driver could change ranges with a flick of a finger.
1939 – Hydra-Matic Drive Fluid
Released in 1939, the 1940–1949 GM Hydra-Matic Drive was used by the Oldsmobile, Cadillac, and Pontiac divisions. The Hydra-Matic Drive used a specialized lubricant called GM Transmission Fluid No. 1. By using the term "fluid" rather than "oil," they hoped to discourage the previously accepted practice of using SAE 20 engine oil. This fluid was composed of a Group 1 base oil and additives to reduce oxidation, foaming, rust, corrosion, varnish, and sludge buildup. This was the world's first automatic transmission fluid, designed for the world's first mass-produced automatic transmission.[2]
This fluid had cold-weather performance problems, which led to the need for an improved fluid, the Type "A" fluid, in 1949. The Hydra-Matic drive fluid was only available at GM dealerships. As a result, regular SAE 20 engine oil was being used in its place at filling stations and repair garages. Engine oil was only approved as a temporary fill fluid and led to transmission problems.
1949 – Type "A" Fluid
1949 Texaco Texamatic Type "A" Fluid. GM License No. AQ-ATF-102
In 1949, General Motors (GM) established an Automatic Transmission Fluid (ATF) Committee (GM ATF Committee). The GM ATF committee established fluid specifications and a qualification procedure to eliminate unsatisfactory fluids and, at the same time, provide the car owner with a means of identifying qualified fluids. The GM ATF Committee released a new Type "A" fluid specification.[3][4] GM partnered with the Armour Research Foundation for fluid and qualification testing. Fluids that met the GM qualification requirements were issued an Armour Qualification (AQ) license number of AQ-ATF-xxx. Example (AQ-ATF-101). The license number had to be displayed on the fluid container.[5]
As a result, qualified GM automatic transmission fluid was made available at retailers and service garages in many places.
From 1949 to 1951, there were only two licensed fluids:
GM Type "A" Automatic Transmission Fluid License No. AQ-ATF-101
Texaco Texamatic Fluid Type "A" License No. AQ-ATF-102
This was the first GM automatic transmission fluid that was made available for sale at retailers other than GM dealerships. In 1951, GM began licensing more Type "A" fluids, which led to several hundred brands of licensed Type "A" fluid on the market. This fluid is backward compatible with the Hydra-Matic Drive fluid produced from 1940 to 1949.
It is important to understand that every automatic transmission produced by any vehicle manufacturer (Oldsmobile, Cadillac, Buick, Chevrolet, Pontiac, GMC, Ford, Mercury, Lincoln, Chrysler, Dodge, Desoto, Packard, and Studebaker) used motor oil or the GM Type "A" transmission fluids from 1949 to 1958.
In 1950, Ford released their 1951 Fordomatic 3-speed transmission, which used the GM Type "A" fluid. In 1952, Chrysler released their 1953 Powerflite 2-speed transmission, which also used GM Type "A" fluid.
This fluid was first used in the following transmissions:
1963–1966 GM Licensed Mobilfluid ATF Type "A" Suffix "A" GM License No. AQ-ATF-752A
In 1957, GM released a new Type "A" Suffix "A" fluid specification.[6] This fluid was better suited for the higher fluid temperatures caused by the unique torque converters[7][8][9] and higher power engines of the day. The fluid specification was revised again in 1958, 1959, and 1960.[10]
GM continued the licensing program, allowing oil companies to produce the new Type "A" suffix "A" fluid under their own brand name. GM-licensed fluids had the armor qualification license number of AQ-ATF-xxxA. Example (AQ-ATF-752A) stamped on the can This fluid is backward compatible with the Type "A" and Hydra-Matic Drive fluids produced from 1940 to 1957.
In 1959, Ford released its own automatic transmission fluid specification (M2C33-A) and stopped using GM fluid specifications. Also in 1959, Toyota released their Toyoglide 2-speed transmission, which used the GM Type "A" suffix "A" fluid.
This fluid was first used in the following transmissions:
DEXRON (B) was released on April 1, 1967. The original fluid better retained the initial properties of the previous Type "A" Suffix "A" fluid (Several thousand cycles compared to 1000 cycles).[11] DEXRON (B) was composed of a more stable, less reactive, hydrotreated Group 1 base oil plus additives to help prevent foaming, oxidation, and damage from elevated temperatures.[12] This was the first GM ATF to advertise 24,000 miles between changes.
This was the first GM ATF to require red dye as an aid in fluid leak detection. Prior to this fluid, GM ATF was the same color as engine oil. Aftermarket ATF was available with red dye.
GM DEXRON (B)-licensed products have a license number on the container that begins with the letter B. Example: B10001. This fluid is backward compatible with all Type "A" suffixes and the Type "A" fluids produced from 1949 to 1966.
This fluid was first used in the following transmissions:
The original DEXRON (B) fluid, as well as earlier GM transmission fluids, used sperm whale oil as an additive to coat internal transmission parts to prevent corrosion and rust. The U.S.Endangered Species Act banned the import of sperm whale oil, so the DEXRON (B) fluid additive package had to be reformulated.[13] In 1973, GM introduced DEXRON-II(C) (GM Spec GM6032M).[14][15]
DEXRON-II(C) was composed of a more stable, less reactive, hydrocracked Group 2 base oil plus a revised additive package with corrosion and rust inhibitors such as jojoba oil; however, the additive package caused problems with corrosion-prone solder in a relatively small number of GM's transmission fluid coolers.[16] After discovering the corrosion problem, GM updated the fluid specification again and released DEXRON-II(D) in 1975.[17]
GM DEXRON-II(C) licensed products have a license number on the container that begins with the letter C. This was the first GM ATF to advertise 50,000 miles between changes. This fluid is backward compatible with all previous DEXRON fluids as well as the Type "A" Suffix "A", and the Type "A" fluids produced from 1949 to 1966.
1975 – DEXRON-II(D)
In 1975, GM released the DEXRON-II(D) specification (GM6032M). DEXRON-II(D) was composed of Group 2 base oil plus an additive package with alternative corrosion and rust inhibitors. The revised corrosion and rust inhibitors made the new fluid hygroscopic, which, while it was not a major problem in automatic transmissions, made DEXRON-II(D) unsuitable for other hydraulic systems in which it was commonly used.[16] GM DEXRON-II(D) licensed products have a license number on the container that begins with the letter D. This fluid is backward compatible with all previous DEXRON fluids as well as the Type "A" Suffix "A", and the Type "A" fluids produced from 1949 to 1966.
As a result of the 1973 OPEC Oil Embargo and fuel shortages, the U.S. government created the Corporate Average Fuel Economy (CAFE) regulations in 1975. The regulations were to be fully implemented by the 1978 model year. The automotive industry responded by changing to three typically unused transmission technologies:
A 4th gear (overdrive)
A Torque Converter Clutch (TCC)
Front Wheel Drive (FWD)
The 1978 introduction of the TCC led to customer complaints of a shudder while driving. All vehicle manufacturers made changes to their ATF specifications and the controls of their TCC to try to alleviate the problem. GM released a revision to the DEXRON-II(D) fluid specification in 1978, Chrysler released the ATF+2 fluid specification (MS-7176D) in 1980, and Ford released the Mercon Type "H' fluid specification (M2C166-H) in 1981.
This fluid was first used in the following transmissions:
In the 1990s, electronic controls of the transmission phased out the old hydraulic/mechanically controlled system. GM was first to market with Cadillac Allante's electronic-controlled transmission system, THM F-7, in 1987, followed by Chrysler and Toyota in 1988, and Ford in 1989. Electronic control of shift pattern (when it shifts), shift timing (how long it takes to shift), shift quality (shift feel), line pressure, and TCC apply and release rates were all affected by the cold temperature performance of the ATF flowing through solenoids.
In 1990, DEXRON-II (E) (GM Spec GM6137M) was released. DEXRON-II (E) was composed of Group 2 base oil plus an additive package. According to the GM Technical Service Bulletin 92-7-2 issued on October 2, 1991, DEXRON-II(E) has better anti-foaming characteristics, improved low-temperature flow characteristics (low-temperature viscosity), and improved high-temperature oxidation stability. This fluid's low-temperature performance was also improved (20,000 cP at -40 °C vs. 50,000 cP at -40 °C).
GM DEXRON-II (E) licensed products have a license number on the container that begins with the letter E. This fluid is backward compatible with all previous DEXRON fluids as well as the Type "A" suffix "A" and the Type "A" fluids produced from 1949 to 1966.
This fluid was first used in the following transmissions:
1991 GM Hydra-Matic 4L80-E (GM's first mass-produced electronically controlled transmission)
The DEXRON-II (E) fluid specification was revised in August 1992. This fluid was first used in the following transmissions:
In 1993, GM released the new DEXRON-III (F) fluid (GM Spec GM6417M and later GMN10055).[18]
DEXRON-III (F) was composed of Group 2+ base oil plus an additive package. According to GM TSB 57-02-01, issued October 2, 1992, The improvements in Dexron-III (F) include better friction stability, higher high-temperature oxidation stability, and better material compatibility. Dexron-III (F) has the same low-temperature fluidity as Dexron-II (E), for better transmission performance in cold weather. This specification failed to address a number of issues concerning long-term durability, such as shear stability and fluid oxidation.
DEXRON-III (F) underwent a number of iterations in an attempt to address various shortcomings but was eventually replaced by new thinking, i.e., DEXRON-VI (J). GM DEXRON-III (F) licensed products have a license number on the can that begins with the letter F. This fluid is backward compatible with all previous DEXRON fluids as well as the Type "A" suffix "A" and the Type "A" fluids produced from 1949 to 1966.
In 1994–1995, some early OBD-II phase-in vehicles experienced a P0300 DTC (random misfire). Engineers determined that road forces being transferred through the TCC were affecting the normal rotational fluctuations of the crankshaft and tricking the ECM into thinking there was a cylinder misfire.
The solution was to create a new kind of TCC that would normally slip around 35 rpm. GM called it the Variable Capacity Converter Clutch (VCCC); other manufacturers had their own names. Some VCCC systems had a shudder or vibration during normal operation. Engineers tried several computer calibration changes, but a revised fluid was also needed to address the issue.
Ford released the new Mercon V Fluid Specification in 1996; GM released the DEXRON-III (G) Fluid Specification (GM6417M) in 1998; and Chrysler released the MS-9602 Change C Fluid Specification in 1999.
This fluid was first used in the following transmissions:
Released in December 1998, GM's DEXRON-III (G) specification (GM6417M) was a synthetic blend automatic transmission fluid, specially developed to address the VCCC shuddering issue. It is also suitable for power steering systems, some hydraulic systems, and rotary air compressors where excellent low-temperature fluidity is required.
GM DEXRON-III (G) licensed products have a license number on the can that begins with the letter G. This fluid is backward compatible with all previous DEXRON fluids as well as the Type "A" suffix "A" and the Type "A" fluids produced from 1949 to 1966.
2003 – DEXRON III (H)
Unlicensed ACDelco ATF Type III(H)
Introduced in 2003, GM's DEXRON III (H) specification (GMN 10055) replaced III (G). The H is an additive package for an updated friction modifier and with an oxidatively stable base oil (group 2). Oils according to this specification have longer maintenance of friction properties and anti-shudder properties, better foam control, and a longer fluid life. universal for all automatic transmissions with and without controlled torque converter lockup clutch, the so-called GKÜB for gear-clutch-lock.
GM DEXRON-III (H) licensed products prior to 2011 had a license number on the can that began with the letter H.
This fluid specification and licensing program was inactivated in March 2011. The ATF Type III (H) fluid shown in the photograph is ACDelco's non-licensed fluid, which is used to support older transmissions that still required the DEXRON-III (H) fluid. This fluid is backward compatible with all previous Dexron fluids as well as the Type "A" suffix "A" and the Type "A" fluids produced from 1949 to 1966.
The fluid on ELF is FluidMatic D3.
2005 – DEXRON-VI(J)
In a joint venture, Ford and GM collaborated on the development of a new 6-speed FWD transaxle (6T70/6F50). Both companies would share the designs and build their own transmissions. The design of these transmissions required a new fluid.
In 2005, Ford released the Mercon Low Viscosity (LV) fluid and GM released the DEXRON-VI specification.[19] The fluid specification for DEXRON-VI (J) was first used as the GM factory-fill automatic transmission fluid for the model year 2006. Roy Fewkes, GM Powertrain Staff Project Engineer and Chairman of the GM ATF/Driveline Lubricants Approval Committee patented the new DEXRON-VI (J) fluid composition under US Patent US8642519B2[20][21]
DEXRON-VI is of a slightly lower viscosity when new compared to the prior DEXRON fluids (a maximum of 6.4 cSt at 100°C for DEXRON-VI and 7.5 cSt for DEXRON-III), but the allowed viscosity loss from shearing of the ATF during use is lower for DEXRON-VI, resulting in the same lowest allowed final viscosity for both DEXRON-III and DEXRON-VI (5.5 cSt) in test.[22] In reality, most of the DEXRON-III fluids typically sheared to about 4.2 cSt in use. The lower, more stable viscosity improved pumping efficiency within the transmission and fluid stability over life. Since Dexron VI is not allowed to thin out (lower its viscosity) as much as Dexron III during use, it requires the use of higher-quality, more shear-stable (less prone to thinning while in use) formulations.[23] The container rear label reads "Full Synthetic Automatic Transmission Fluid"; however, the base oil composition is not stated. The current GM specification that defines the fluid is GMW16444, which superseded the original specification, GMN10060.
All DEXRON-III (H) licenses expired permanently at the end of 2011, and GM now supports only DEXRON-VI fluids for use in their older automatic transmissions.[24] Aftermarket fluids asserted by their manufacturers to meet DEXRON-III(H) and earlier standards continue to be sold under names such as DEX/Merc. These fluids are not regulated or endorsed by GM.[23]
GM DEXRON-VI(J) licensed products have a license number on the container that begins with the letter J. This was the first GM ATF to advertise 100,000 miles (160,000km) between changes for "Normal Driving" conditions and 50,000 miles (80,000km) for "Severe Service".[25] This fluid is backward compatible with DEXRON-III(H) and DEXRON-III(G) fluids only.
This fluid was first used in the following transmissions:
2007 6T70/6T75 Transaxles
2007 6L80 Transmission
The fluid on ELF is FluidMatic G6 SYN.
2013 – DEXRON-HP
With increasing CAFE regulations, smaller engines with very narrow torque bands were being put in vehicles with 6- and 8-speed transmissions to improve fuel economy. A new fluid revision was needed for the proper operation of the new 2015 GM 8L90 and 8L45 8-Speed RWD/4WD automatic transmissions. This was GM's first "lifetime" fluid, with no fluid or filter changes required under "normal" driving conditions. The current GM specification that defines the fluid is GMW16974.
There have been two versions of this fluid specification:
In July 2013, GM released the Low Viscosity (LV) Dexron-HP (High Performance) Fluid Specification. As shown on the photograph of the rear panel, the 2013 Dexron HP is composed of a group 4 polyalphaolefin (PAO) base oil and additives provided by the Afton Chemical Corporation. The rear panel label of early containers of this fluid incorrectly states that this fluid is backward compatible with previous DEXRON ATF; it is not. The label was corrected on later bottles of the fluid.
In May 2017, a revision was made to the GMW16974 fluid specification. A change to a Group III+ base oil rather than a Group 4 PAO base oil was made, as was another additive package option from Afton Chemical Corporation.
GM DEXRON-HP licensed products have a license number on the container that begins with the letter J.
This fluid was first used in the following transmissions:
The fluid specification for DEXRON-ULV (ultra-low viscosity) was introduced on January 2, 2014. DEXRON-ULV is composed of a Group 3+ base oil and additives needed for the proper operation of the 2017 and above GM 10L90 and the Ford 10R80 10-Speed rear-wheel-drive automatic transmission.
This transmission and the transmission fluid specification were co-developed by Ford and GM. The current specification that defines the fluid is Ford WSS-M2C949-A. This fluid is also marketed as Mercon ULV.
The quart containers of DEXRON-ULV must be shaken to stir up the additives before pouring. This fluid is not backward compatible with any previous fluids.
This fluid was first used in the 2017 10L90 10-Speed Automatic Transmission.
2016 – Mobil 1 Synthetic LV ATF HP "Black Label"
In 2016, a new fluid specification for a "DEXRON Approved" Mobil 1 Synthetic LV ATF HP was introduced in GM Technical Service Bulletin 16-NA-175. The revision was to help correct a torque converter clutch shudder in the GM 8L90, 8L80, and 8L45 automatic transmissions.
DEXRON LV ATF HP is made by Mobil and is marketed as Mobil 1 LV ATF HP. DEXRON LV ATF HP is composed of a poly-alpha-olefin (PAO) Group IV base oil and additives developed by Afton Chemical needed for the proper operation of the 2015 and above GM 8L90 8-Speed rear-wheel drive automatic transmission. The current GM specification that defines the fluid is GMW16974 (2nd Edition, May 2017).
2016 – DEXRON III(K) for Manual Transmissions
On August 1, 2016, GM released the DEXRON III (K) fluid specification (GM Spec GMW17639) as a fluid to support older GM manual transmissions and power steering systems requiring the previously discontinued DEXRON-III (H) fluid.
Warning: The additive package for automatic transmissions has been removed from this fluid; do not use it in any automatic transmission.
2018 – Mobil 1 Synthetic LV ATF HP "Blue Label"
On October 1, 2018, a special fluid specification (GMNA-9986555[27]) was introduced for a revised "DEXRON Approved" Mobil 1 Synthetic LV ATF HP. This revised fluid was introduced in GM Technical Service Bulletin 18-NA-355 in December 2018. The revision is to help correct a torque converter clutch shudder in the GM 8L90 and 8L45 automatic transmissions after a complete flush of the system.
DEXRON LV ATF LV is made by Mobil and is marketed as Mobil-1 LV ATF HP. Mobil-1 LV ATF HP is composed of a Gas to liquids (GTL) Group 3+ Base oil and additives developed by Infineum needed for the proper operation of the 2015 and above GM 8L90 and 8L45 8-Speed rear wheel drive automatic transmission.
Containers of this fluid have a revised blue and silver label on the front of the container. This "DEXRON Approved" DEXRON-HP product has a J-62120 license number on the rear label of the container.
GM ATF Change Interval under "Normal Driving" Conditions*
Fluid Specification
Miles
1940 Hydra-Matic
5,000
1949 Type "A"
10,000
1957 Type "A" Suffix "A"
15,000
1967 Dexron (B)
24,000
1973 Dexron-II(C)
50,000
1975 Dexron-II(D)
50,000
1990 Dexron-II(E)
100,000
1993 Dexron-III(F)
100,000
1998 Dexron-III(G)
100,000
2003 Dexron-III(H)
100,000
2006 Dexron-VI(J)
100,000
2013 Dexron-HP
150,000
2014 Dexron-ULV
150,000
*See your vehicle maintenance guide for definition of "Normal Driving" conditions and recommended service interval
GM Lifetime automatic transmission fluids made from higher-quality base oil and an additive package are more chemically stable, less reactive, and do not experience oxidation as easily as lower-quality fluids made from lower-quality base oil and an additive package. Therefore, higher-quality transmission fluids can last a long time in normal driving conditions (typically 100,000 miles (160,934km) or more).
The definition of "lifetime fluid" differs from transmission manufacturer to transmission manufacturer. Always consult the vehicle maintenance guide for the proper service interval for the fluid in your transmission and your driving conditions.
Chevrolet Colorado Example: According to the Scheduled Maintenance Guide of a 2018 Chevrolet Colorado with "Lifetime Fluid," the vehicle could have two different fluid service intervals depending upon how it is driven:[28]
1. Normal Driving
Carry passengers and cargo within the recommended limits on the Tire and Loading Information label.
Driven on reasonable road surfaces within legal driving limits.
Under "normal" driving conditions, the automatic transmission fluid and filter never need to be changed.
2. Severe Driving
Mainly driven in heavy city traffic in hot weather
Mainly driven in hilly or mountainous terrain
Frequently towing a trailer
Used for high speed or competitive driving
Used for taxi, police, or delivery service.
Under "Severe" driving conditions, replace automatic transmission fluid and filter every 45,000mi (72,420km)
Base Stock Oil Categories for GM ATF based upon timeline of availability vs. fluid life under "Normal" driving
API BaseStock Oil
Miles
1940 Group 1
5,000
1949 Group 1
10,000
1957 Group 1
15,000
1967 Group 1*
24,000
1973 Group 1*
50,000
1975 Group 1*
50,000
1990 Group 2
100,000
1993 Group 2
100,000
1998 Group 2+
100,000
2003 Group 2+
100,000
2006 Group 4
100,000
2013 Group 3+
150,000
2014 Group 3+
150,000
*Hydrotreated Group 1
GM ATF Change Interval under "Severe Driving" Conditions*
Fluid Specification
Miles
1940 Hydra-Matic
2,500
1949 Type "A"
5,000
1957 Type "A" Suffix "A"
7,500
1967 Dexron (B)
12,000
1973 Dexron-II(C)
25,000
1975 Dexron-II(D)
25,000
1990 Dexron-II(E)
50,000
1993 Dexron-III(F)
50,000
1998 Dexron-III(G)
50,000
2003 Dexron-III(H)
50,000
2006 Dexron-VI(J)
50,000
2013 Dexron-HP
45,000
2014 Dexron-ULV
45,000
*See your vehicle maintenance guide for definition of "Severe Driving" conditions and recommended service interval
A hydraulic fluid or hydraulic liquid is the medium by which power is transferred in hydraulic machinery. Common hydraulic fluids are based on mineral oil or water. Examples of equipment that might use hydraulic fluids are excavators and backhoes, hydraulic brakes, power steering systems, automatic transmissions, garbage trucks, aircraft flight control systems, lifts, and industrial machinery.
An automatic transmission is a multi-speed transmission used in motor vehicles that does not require any input from the driver to change forward gears under normal driving conditions. Vehicles with internal combustion engines, unlike electric vehicles, require the engine to operate in a narrow range of rates of rotation, requiring a gearbox, operated manually or automatically, to drive the wheels over a wide range of speeds.
The Chevrolet Corsica is a front-wheel drive compact car that was produced by Chevrolet from 1987 until 1996. The Corsica was built upon the L-body platform. It shared the L-body with the 2-door Beretta, and the rebadged revival of the Pontiac Tempest which was essentially the same car, but was only sold in Canada. The Corsica came in two styles and four trims. Sold initially only as a 4-door sedan, it was also available as a 5-door hatchback from model years 1989 until 1991. Corsicas were built alongside the Beretta by both the Wilmington Assembly in Delaware and Linden Assembly in New Jersey.
The Tempest is an automobile that was produced by Pontiac from 1960 to 1970, and again from 1987 to 1991.
Gear oil is a lubricant made specifically for transmissions, transfer cases, and differentials in automobiles, trucks, and other machinery. It has high viscosity and usually contains organosulfur compounds. Some modern automatic transaxles do not use a heavy oil at all but lubricate with the lower viscosity hydraulic fluid, which is available at pressure within the automatic transmission. Gear oils account for about 20% of the lubricant market.
Hydramatic is an automatic transmission developed by both General Motors' Cadillac and Oldsmobile divisions. Introduced in 1939 for the 1940 model year vehicles, the Hydramatic was the first mass-produced fully-automatic transmission developed for passenger automobile use.
Roto Hydramatic was an automatic transmission built by General Motors and used in some Oldsmobile, Pontiac and Holden models between 1961 and 1965. It was based on the earlier, four-speed Hydramatic, but was more compact, providing only three forward speeds plus a small 8" fluid coupling with a stator inside of the fluid coupling. Oldsmobile, one of the companies that used this transmission in some of its cars, called the fluid couplings stator the "Accel-A-Rotor." The lightweight, aluminum-cased transmission was sometimes nicknamed the "Slim Jim." HydraMatic Division calls the Roto a four-range, three-gear HydraMatic.
The Turbo-Hydramatic 125 was the first in a line of automatic transmissions from General Motors designed for transverse engine application. Introduced in 1980, the line evolved into today's 4T40/45/65/80 line.
The Aisin AW AF33 is a 5-speed automatic transaxle developed and manufactured in Anjo, Japan by Aisin AW, a division of Aisin. It is designed to be used in transverse engine configurations in both FWD and AWD configurations.
The GM–Ford 6-speed automatic transmission is an automatic transaxle originally designed for transverse engine applications in cars. With design work having begun in 2002, General Motors and Ford Motor Company jointly committed to investing US$720 million in their manufacturing plants to support the new transmission.
The Ultradrive is an automatic transmission manufactured by Chrysler beginning in the 1989 model year.
The 4F27E is an electronically controlled 4-speed automatic transaxle transmission developed by Mazda and Ford. Mazda's name for this transmission is FN4A-EL, Ford's name for this transmission is 4F27E. Mazda's FS5A-EL is the 5-speed successor to this transmission which shares many of the same parts.
Automatic transmission fluid (ATF) is a specialized hydraulic fluid that is essential for the proper functioning of vehicles equipped with automatic transmissions. Usually, it is coloured red or green to differentiate it from motor oil and other fluids in the vehicle.
The Tremec TR-6060 six-speed manual transmission features six forward speeds and one reverse speed. It is derived from the Tremec T-56 6-speed manual transmission. As usual, the forward helical cut gears are synchronized. However, the reverse gear operates through a fully synchronized constant-mesh system. The TR-6060 contains removable wear pads on the shift forks, and uses aluminum alloys for the main case, extension housing, and clutch housing. It is a double overdrive transmission. The TR-6060 is manufactured by TREMEC and is rated for 430 lb⋅ft (580 N⋅m) to 650 lb⋅ft (880 N⋅m) of torque, depending on gearing.
The Hydra-Matic 6T40 and similar 6T30, 6T45, and 6T50 are transversely-mounted six speed automatic transmissions produced by General Motors. The 6T40, referred to in GM inner circles as the GF6, made its debut in the 2008 Chevrolet Malibu, available with the 2.4 L LE5Ecotec engine making 164 horsepower (122 kW), and has since also been made available on the Chevrolet Cruze, Daewoo Tosca and Buick LaCrosse. It features clutch-to-clutch shifting, eliminating the bands used on older transmission designs. GM chose an "on-axis" design as opposed to folding the gearset behind the engine and transferring power through the use of a chain, as is used in most other GM front wheel drive transaxles. Ford Motor Company also produces their own variant, called the 6F35. The Buick Encore uses the 6F35 mated to the 1.4 turbo.
The Borg-Warner 35 transmission (BW-35) is an automatic transmission produced by the BorgWarner company. This article also applies to variations—the M-36 and M-37. When this article refers to "M-3x" it refers to all models. When model number specific it will use the exact model number.
Oil additives are chemical compounds that improve the lubricant performance of base oil. The manufacturer of many oils can use the same base stock for each formulation and can choose different additives for each use. Additives comprise up to 5% by weight of some oils.
The 5R05, also called RE5R05A, JR507E/JR509E or TG5C/TG5D "5EAT", is a Jatco 5-speed automatic transmission, released in 2002, used in rear wheel drive or 4X4 vehicles with longitudinal engines. It shares little to nothing in common with the older 5R01 transmission.
Mercon represents a series of technical standards for automatic transmission fluid, developed and trademarked by Ford Motor Company. This designation serves as a mark of quality that Ford has established for fluids used in automatic transmissions. The Mercon name, which has evolved into a brand, is licensed by Ford to various manufacturers. These companies are authorized to produce the fluid according to Ford's specifications and market it under their own brand names.
This page is based on this Wikipedia article Text is available under the CC BY-SA 4.0 license; additional terms may apply. Images, videos and audio are available under their respective licenses.
