This article needs additional citations for verification .(September 2016) |
FS class E.636 | |||||||||||||||||||||||||||||||
---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
![]() E.636.002 in its original livery, property of FerAlp Team museum in Bussoleno | |||||||||||||||||||||||||||||||
| |||||||||||||||||||||||||||||||
| |||||||||||||||||||||||||||||||
| |||||||||||||||||||||||||||||||
|
The FS E.636 is a class of Italian articulated electric locomotives. They were introduced in the course of the 1940s until the 1960s, and have been decommissioned since 2006. They have been one of the most numerous Italian locomotive groups, and have been widely employed during their long career, hauling every type of train, ranging from freight to long range passenger services. Their introduction also saw the employment of some revolutionary (for the time) design concepts, such as the articulated carbody and the three bogies scheme.
The E.636 was designed to overcome the problems shown in the 1930s by both the E.626 multi-purpose and E.326 high-speed locomotives, in order to better handle the increasing railway traffic in Italy.
The E.636 was the first Italian locomotive adopting the Bo-Bo-Bo configuration with chassis divided into two articulated parts pivoting on the central bogie, which is very well suited for the often tortuous lines of Italy and that would have been later repeated on the E.645/646 and E.656 classes. The presence of a great number of wheels was considered important due to the presence of a number of high-slope lines in the Italian railroad network as it increases the adhesion limit, meaning that the locomotive is less prone to wheel slips. The new engines weighted approximately 101 short tons (90 long tons; 92 t). Engines were initially the same as E.626. The 32R used a 3 kV catenary but this was soon shown to be inadequate and so were updated and provided with a new hollow axle transmission system. Mainly two different gear ratios were installed: 21/65 for sloping lines or heavy freight trains (maximum speed of 95 km/h (59 mph), elevated later to 110 km/h), and the longer 28/65, with a maximum speed of 120 km/h (75 mph), suited for passenger services.
The locomotive was built in three different series:
The first unit entered service in May 1940. Six locomotives were destroyed during World War II. After the war the total number of locomotives was brought to 469, also thanks to the support from the Marshall Plan, and making it one of the most numerous groups of Italian locomotives. All the units were painted with an Auburn livery; this was changed in the 1990s to a white one with green stripes for most trains (XMPR livery).
By 2000s railway standards, E.636s were old and uncomfortable. The original design of the cockpits proved absolutely unfit to modern safety standards: this was shown in an accident in 1996 at Sulmona, where the engine driver died despite the low speed, without being able to leave the cockpit in time. 200 units were therefore rebuilt and stripped of all asbestos.
Starting from the 1990s, E.636s were used mainly for cargo services, save for the more backlog Sicilian lines. Some units were lent to minor Italian railroads. The phasing out of the entire class was completed in May 2006.
E.636 are very simple locomotives. Most functions of the main command circuit are accomplished through various relays and contactors. In case of failure the train driver could easily fix them to at least free the tracks; also, especially in the last years of their service, E.636s were the first locomotives that the new train drivers studied during their training courses, due to their simple working mechanics.
As most older Italian locomotives, E.636 has a rheostat (formed by 16 cast iron resistors connected in series, for a total resistance of 29 ohms) that needs to be gradually, but as soon as possible, excluded on start-ups, which regulates the current to the six 32R-200 DC traction motors, two per bogie.
The motors can be connected in three combinations: series, series-parallel and parallel; each combination provides a progressively higher voltage to the motors, therefore increasing the current.
Their set-up is the following:
Combination | Motor set-up | Voltage per motor |
---|---|---|
Series | All motors are connected in series | 500 V |
Series-Parallel | Two branches of three motors | 1000 V |
Parallel | Three branches of two motors | 1500 V |
The rheostat (connected in series to the traction motors) is necessary because the DC motor has the intrinsic characteristic of absorbing a current inversely proportional to its rotating speed; at high speeds, it absorbs less current. This means that on start the current would be very high, because the only resistance encountered would be only the one offered by motors and internal conductors, which is very low (a short circuit, in practice). The rheostat increases the overall resistance when starting the locomotive, lowering the current and allowing a smoother start.
In S-P and P combinations, the rheostat is divided in three branches connected in parallel; this lowers the overall rheostat equivalent resistance to about 3.5 ohm, while in S combination its elements are all connected in series.
Like almost every Italian locomotive with rheostatic regulation since E.626, traction is controlled via a lever (commonly referred to as maniglione) mounted on a support called roncola; this support has several notches, each representing a portion of the rheostat, plus three "end combination" notches and two "transition" positions (a bigger block between the notches). To accelerate, the driver rotates gradually counterclockwise the lever notch by notch, and in doing so the various rheostat contactors are closed, shunting the resistors and lowering the total rheostat resistance, also allowing more current to the motors; as speed builds up, the counter-electromotive force lowers this current, until the rheostat is no longer necessary: it is, then, totally excluded (obviously if in traction and in an "end combination" notch). This safely allows traction for an indefinite period of time, within certain limits.
When the end combination notches are reached, the driver can then insert the single shunt (one for each combination) or make a transition to the next combination, reintroducing the rheostat which has to be excluded again, for the following combinations until the end of the parallel combination is reached. The shunts increase the current into the motors by shunting some motor spires (through a contactor in parallel); this reduces the magnetic flux and, as said, increases the current (since the two are inversely proportional). There are various "shunt levels", depending on the locomotive, as is further explained; usually, there is one per combination. It is also important to remove the shunts before making a transition, in order to avoid flashes due to abnormally high currents.
Like some E.626s, E.636 locomotives are not provided with the "CEM" motor combiner (CEM stands for Combinatore Escluditore Motori), a device that, during transitions, rotates, combining the motors accordingly through various contactors.
On E.636, this is achieved through the uses of more delicate spires, so transitions (especially backward ones) need to be very slow and gradual. The optimal moment to pass to the following/preceding combination first/last notches is when the motor ammeter indicates 0 Ampères, which happens when passing over the transition position with the lever (the driver should briefly stop in the middle of the block and pay attention to the ammeter), meaning that the motor contactors are in optimal position and is safe to proceed. Failure in doing this may result in flashes that will damage the contactors.
An important parameter the driver has to consider, especially during rheostatic exclusion, is the current into the traction circuit.
In particular, if he is excluding too fast, a wheel slippage can occur (in this case the use of sanders and reducing throttle can help), and one or more maximum current relays can open when the maximum allowed current value is exceeded.
The locomotive is protected from overly high currents through different kinds of relays:
When they open, they also open the main breaker; that cuts the connection to the catenary.
Before the 1970s, the maximum currents for the relays were the following:
Relay | Maximum Current allowed |
---|---|
RMx | 1050 A |
RMx 1-2 | 450 A |
RMx 2-3 | 350 A |
RMx 3-4 | 350 A |
RMx REC | 500 A |
Between 1970 and 1980, the previous values changed:
Relay | Maximum Current allowed |
---|---|
RMx | 1200 A |
RMx 1-2 | 450 A |
RMx 2-3 | 400 A |
RMx 3-4 | 400 A |
RMx REC | 500 A |
As can be seen, the currents allowed in series are 450 A in both cases, while in Series-Parallel and Parallel combinations are 350 A and 450 A respectively.
As said, one level of field shunt (percentage of field weakening: 31%) is allowed in each combination; however, some units received 92-250 (used on FS Class E.424) and 32RT-200 type motors which allowed a maximum of 5 levels of field shunts (percentage of field weakening: 65%, 45% on the latters). These units were later made identical to standard ones again.
Units from 001 to 243 mounted Negri-type transmission, except for units 195-198 and 176-183 which had a rubber tampons in place of coil packs and double hollow axle transmission and rubber tampons respectively.
All the following built units had the same transmission type of 176-183 but slightly different.
Different locomotives have received various gear ratios (see "Special Units" for more details):
Gear ratio | Max speed (km/h) | Notes |
---|---|---|
21/65 | 110 | Originally 95 km/h elevated to 105 km/h shortly after, then to 110 in 1982 |
28/65 | 120 | Eliminated in 1991 |
20/65 | 120 | Units 044 and 089 only |
24/74 | 105 | Units 271-275 only |
The motor cooling-fans were activated by two 4.5 kW 3,000 V dedicated motors until unit 201; later units have 1 kW motors identical to the ones used on FS Class E646; they are also used as dynamos to recharge the 24 V batteries (only if line voltage is greater than 1,500 V) used to feed low tension devices (lights, locomotive heating systems, contactors etc.)
Air production on the locomotive was granted by two C38 type compressors; later they were upgraded with the more reliable W242, however, on some units, only one compressor was replaced, leaving one of each type in use on a single locomotive; the C38 produced air until 8 bars in main reservoir tanks were reached, while the W242 from 8 to 9 bars. In fact, on these units, only the W242 was used on normal conditions; the other one only if pressure dropped below 7 bars.
Main-tanks and the 24 V batteries supplies air and current to several systems:
Originally the locomotive mounted a 7-position L-type Westinghouse brake controller and wheel-type locomotive brake, later replaced by the more common Oerlikon FV4 and RA-M2 levers respectively.
The locomotive has three kinds of brakes:
It is a negative-type brake and is called continuous because it extends itself through the entire train, automatic because if brake continuity is no longer present (general pipe breaks), emergency braking is automatically applied.
On units with Breda-type valves and Oerlikon levers the brakes are graduable during braking and releasing; the working principles are the following.
The braking system of the locomotive is formed by an array of components:
When brakes are released, pressure in the brake pipe is about 5 bar (500 kPa; 73 psi), and 0 bar (0 kPa; 0 psi) in brake cylinders.
To brake the train the driver, by moving the brake controller, creates a depression in a particular tank called "bariletto", which, through a series of coils creates a connection to the exterior which makes the general pipe to gradually lower its pressure to a value equal to the one present in the aforementioned tank (how fast this happens depends on train length: the longer it is, the slower this procedure will be). Inside the distributore the command reservoir pressure "wins" over now lower pipe pressure and thus the piston moves, creating a connection between the braking cylinders and the auxiliary reservoir (fed by the main tanks), which will then send a quantity of air to the brake cylinders proportional to the entity of the depression. The maximum pressure that can be reached into the brake cylinders on E636 is 3.8 bar (380 kPa; 55 psi), which corresponds to a pressure inside the general pipe of about 3.5 bar (350 kPa; 51 psi).
In case of emergency braking, the brake pipe is put to direct communication with outside atmosphere, rapidly dropping pressure, and consequently making the train brake very fastly (though there isn't a variation of braking power: only the braking speed is affected).
To release brakes, the driver makes the pressure rise in the bariletto, via the brake controller; the pressure in the brake pipe is restored (air is taken from the main reservoir tanks, and from the main pipe if present) to the value present in the bariletto. Inside the ditributore the brake pipe pressure wins over the command reservoir pressure and so the connection between the brake cylinders and the auxiliary tanks is modified (or cut, depending on the pipe pressure); the brake cylinders unload themselves sending their air outside until their pressure reaches a value proportional to the entity of the depression. When pipe pressure is 5 bar (500 kPa; 73 psi), the cylinders will unload until they are empty.
For a faster brakes' release, it is also possible to briefly "overload" the braking system to a pressure proportional to the depression previously present, up to a maximum pressure of 7.2 bar (720 kPa; 104 psi); shortly after this, the pressure drops to 5.5 bar (550 kPa; 80 psi), and is gradually brought back to 5 bar (500 kPa; 73 psi) in about 240 secs.
However, on units with Triple Valves (Distributore tipo Westinghouse) and 7-position levers, braking circuit is slightly different. The distributore is divided in two parts like said before, but there isn't the command reservoir tank: when the pressure inside the brake pipe drops, it's directly the auxiliary reservoir that makes the frame put in the middle moving. Braking is not gradual on release in this case: when the driver puts the controller on "release" position, brakes are fully released; if he brakes again too shortly after, there is the risk to have a loss of braking power because there may not be enough air to brake optimally, since the absence of the fixed pressure of the command reservoir doesn't ensure that there is enough air to safely release the brakes. It is even possible to fully exhaust the reservoir, with the consequent danger to not be able to stop the train at all. This is prevented in units with Breda and other types of valves as the brakes cannot be fully released if there is not enough air in main reservoir tanks to brake again.
There is a risk associated to the "overload" operation. Inside the distributore the pressures inside the two chambers are balanced: during the overload both command reservoir and brake pipe pressures rise proportionally. As said they are gradually lowered back to 5 bar (500 kPa; 73 psi) but it may happen that the command reservoir "gets struck" to a higher pressure, while the pipe pressure is lower. This keeps the connection between the auxiliary reservoir and the brake cylinders and consequently the brakes in effect. In this occurrence a possible solution is to overload again the system so pressures can be rebalanced, or, if this doesn't work, to manually "reset" the command reservoir (emptying it) by pulling a lever located outside. On units with seven-position levers the risk is greater: the pipe is put to direct connection with the main tanks and, if the controller is left for too much time in the overload position, it may reach a very high pressure (even 9 bar or 900 kPa or 130 psi). It is very easy for the brakes to remain in effect in this case, and the only practicable solution is to manually empty the command reservoir tanks as said above.
The locomotive is formed by two half carbodies, pivoting over the central bogie. Between them, there is a bellows, which was originally made with rubber then replaced in the 1950s by an impermeable membrane. In recent years this was further replaced by flexible plastic material.
On post war units, 7 mm (0.28 in) reinforcement frames have been introduced on the chassis and under the cabs, as the first 108 units showed some mechanical weaknesses in those points; in the mid-1980s it was decided to reinforce only the chassis on pre-war units (however units 026 an 065 never received these modifications).
To reduce parasite motion, dampers were mounted between the carbodies: glycerine-type from units 1-276 and special-oil type from unit 277 onwards, although these were later eliminated in 1977 because considered useless.
The first 108 units had different rheostat ventilation shafts on the roof than the rest of the units ones, although these were later replaced with the more efficient shafts used on the latter units.
They also had sliding oil-buckles, while following units had rolling bearing ones.
Units 162-171 were equipped with French-derived Athermos buckles for testing purposes, which were later removed.
Sandthrowers were mounted internally into the bogie in the units 001 - 108; after the war they were replaced by external ones that also were natively mounted on later units.
The first 108 locomotives originally had mounted a vigilance pedal designed by FS engineer Minucciani, that required a periodic acknowledgement from the driver when the train was moving (or emergency braking would have been commanded), but after the war, due to labor union pressures, it was discontinued; however, starting from the 1970s, many (not all) units received "Ripetizione Segnali a 4 codici" system, Hasler speedometer and a modified "speed graph recorder" (Zona tachigrafica), that also recorded the codes received from the RS.
During the 1960s-1970s Ansaldo-Breda built a locomotive derived from E.636 for use in Yugoslavia, classified JŽ 362.
A railway air brake is a railway brake power braking system with compressed air as the operating medium. Modern trains rely upon a fail-safe air brake system that is based upon a design patented by George Westinghouse on April 13, 1869. The Westinghouse Air Brake Company was subsequently organized to manufacture and sell Westinghouse's invention. In various forms, it has been nearly universally adopted.
The vacuum brake is a braking system employed on trains and introduced in the mid-1860s. A variant, the automatic vacuum brake system, became almost universal in British train equipment and in countries influenced by British practice. Vacuum brakes also enjoyed a brief period of adoption in the United States, primarily on narrow-gauge railroads. Their limitations caused them to be progressively superseded by compressed air systems starting in the United Kingdom from the 1970s onward. The vacuum brake system is now obsolete; it is not in large-scale usage anywhere in the world, other than in South Africa, largely supplanted by air brakes.
Rail terminology is a form of technical terminology. The difference between the American term railroad and the international term railway is the most significant difference in rail terminology. These and other terms have often originated from the parallel development of rail transport systems in different parts of the world. In English-speaking countries outside the United Kingdom, a mixture of US and UK terms may exist.
This article is a glossary of the main components found on a typical steam locomotive.
A railway brake is a type of brake used on the cars of railway trains to enable deceleration, control acceleration (downhill) or to keep them immobile when parked. While the basic principle is similar to that on road vehicle usage, operational features are more complex because of the need to control multiple linked carriages and to be effective on vehicles left without a prime mover. Clasp brakes are one type of brakes historically used on trains.
The DB Class 101 is a class of three-phase electric locomotives built by Adtranz and operated by DB Fernverkehr in Germany. 145 locomotives were built between 1996 and 1999 to replace the 30-year-old and aging Class 103 as the flagship of the Deutsche Bahn, primarily hauling Intercity services. This class encompasses the latest generation of locomotives of the Deutsche Bahn.
Electric locomotives were first used on the London Underground when the first deep-level tube line, the City and South London Railway (C&SLR), was opened in 1890. The first underground railways in London, the Metropolitan Railway (MR) and the District Railway (DR), used specially built steam locomotives to haul their trains through shallow tunnels which had many ventilation openings to allow steam and smoke to clear from the tunnels. It was impractical to use steam locomotives in the small unvented tubular tunnels of the deep-level lines, and the only options were rope haulage or electric locomotives.
The FS E.645 and E.646 are two classes of similar electric locomotives used on Italian railways. They were introduced during the 1950s and they were retired in 2009.
The class E 10 is an electric locomotive of the Deutsche Bundesbahn, introduced in 1952. It belongs to the Einheits-Elektrolokomotiven program and was built for express passenger service. In 1968 the series was redesignated as class 110 (E10) and class 112 (E10.12). In 1988 the last series of class 112 locomotives were designated as class 114, and in 1991 the remaining locomotives of class 112 were designated as class 113. In 2006 38 locomotives were designated as class 115.
ER2 electric trainset is a DC electric multiple unit which was in production by the Railroad Machinery Plants of Riga from June 1962 to mid-1984. It was essentially an improvement of the ER1 design, featuring footboards for low platforms, and aprons for high platforms, as well as improved electrical equipment and minor changes to the bodywork. Since the mid-1960s, the ER2 has been the most widely used type of suburban train in the Soviet Union and its successor states.
The Class E.656 is an Italian articulated rheostatic-type electric locomotive built from 1975 to 1989. An evolution of the E.646, they are mixed traffic locomotives, and have been used on every kind of train, ranging from freight to intercity passenger transport.
The E.464 is a class of Italian railways electric locomotives. They were introduced in the course of the 1990s for hauling light trains, especially for commuter service. They were acquired by FS Trenitalia to replace the old E.424 and E.646, dating from the 1940s and 1950s. The class was originally designed by ABB Trazione, later ADTranz, and produced in the Italian plant of Vado Ligure.
The FS E.632 and E.633 are two classes of Italian railways electric locomotives. They were introduced in the course of the 1980s.
The electro-pneumatic brake system on British mainline railway trains was introduced in 1950 and remains the primary braking system for multiple units in service today, although London Transport underground trains had been fitted with EP brakes since the 1920s. The Southern Region of British Railways operated a self-contained fleet of electric multiple units for suburban and middle-distance passenger trains. From 1950, an expansion of the fleet was undertaken and the new build adopted a braking system that was novel in the UK, the electro-pneumatic brake in which compressed air brake operation was controlled electrically by the driver. This was a considerable and successful technical advance, enabling a quicker and more sensitive response to the driver's operation of brake controls.
The FS E.424 is a class of Italian railways electric locomotives. They were built in 1943-1951 and have been decommissioned in 2008.
FS ALe 642 is a class of Italian Electric Multiple Unit trains built from 1991 to 1995 for use on secondary lines and for commuter traffic. In service since 1991.
The South African Railways Class 6E1, Series 1 of 1969 was an electric locomotive.
The Spoornet Class 18E, Series 1 of 2000 is a South African electric locomotive.
FS Class E.333 was a class of electric locomotives of the Ferrovie dello Stato (FS), powered by three-phase alternating current, which were in service from 1923 to 1968. They were designed by Kálmán Kandó for hauling fast passenger trains. Having the same electrical equipment as the FS Class E.552 locomotives, they presented the same defects and had to be modified. After modification, they were able to carry out the services for which they were designed.
The SNCF Class BB 900 was a class of 35 mixed-traffic electric locomotives built between 1936 and 1937 for État. The class was a development of the pre-war Midi Class E4700 and very similar to the later Class BB 300 and Class BB 325. Initial use was on the Paris–Le Mans line. The class was withdrawn in 1987 after 50 years in service.