Megawatt Charging System

Last updated
Megawatt Charging System connector
MCS v3.2.svg
Prototype v3.2 MCS connector; there are two primary power (DC) pins, four communications/detection (C) pins, and one protective earth (PE) pin.
Type Electric vehicle charging
Production history
Designer MCS (former HPCCV) working group, CharIN
Designed 2020‒2022
Produced 2023 (planned)[ citation needed ]
General specifications
Pins 7 [1]
Connector MCS [1]
Electrical
Signal DC
Earth Dedicated pin
Max. voltage 1,250 V [2]
Max. current 3,000 A [2]
Data
Data signal ISO 15118-20

The Megawatt Charging System (MCS) is a charging connector under development for large battery electric vehicles. The connector will be rated for charging at a maximum rate of 3.75 megawatts (3,000 amps at 1,250 volts direct current (DC)).

Contents

The MCS connector is being advanced by the CharIN organization, with aspirations that it become a worldwide standard charging connector for large and medium commercial vehicles. [3]

History

A Charging Interface Initiative e.V. (CharIN) task force was formed by industry actors in March 2018, with the purpose to "define a new commercial vehicle high power charging standard to maximize customer flexibility." [3] CharIN had previously developed the Combined Charging System (CCS) specification. From early 2018 until late 2019, the abbreviation HPCCV (High Power Charging for Commercial Vehicles) was used, following the name of the CharIN consortium taskforce. The purpose statement was later revised to "work out requirements for a new commercial vehicle high power charging solution to maximize customer flexibility when using fully electric commercial vehicles. The scope of the technical recommendation is to be limited to the connector, and any related requirements for the EVSE, the vehicle, communication, and related hardware." [4]

The HPCCV held a meeting in September 2018 to build consensus on proposed requirements, and the CharIN Board of Management approved a set of consensus requirements in November 2018. [3] Five companies submitted candidate designs to meet the requirements: Tesla, Electrify America, ABB, paXos, and Stäubli. [5] HPCCV selected a charging plug and socket design in May 2019, which was endorsed by CharIN leadership in September 2019. [3] The version 1.0 HPCCV connector had a triangular shape and round power pins, but the design required further development as it was not finger-proof (safe from accidental contact with the power pins). [6]

Approximate drawing of previous version 2 draft outlet; DC+- would have been carried via two "tuning fork" contacts Draft-mcs-megawatt-charging-system-geometry.svg
Approximate drawing of previous version 2 draft outlet; DC± would have been carried via two "tuning fork" contacts

A test of seven vehicle inlets and eleven connectors was held at the US National Renewable Energy Laboratory (NREL) in September 2020. The prototype hardware represented designs from seven different manufacturers, and six additional manufacturers participated virtually. Criteria evaluated included fit/compatibility, ergonomics, and thermal performance. [7] [8] Evaluations at maximum current (3000 A) were conducted with cooling of both the inlet and the connector; for connector cooling only, current was limited to 1000 A, and without cooling, current was limited to 350 A. [9] Versions 2.0 through 2.4 of the MCS connector used "hairpin" shaped contacts, but it was later changed to version 3.0 through 3.2, which returned to the triangular shape with larger pins and longer protective sheaths to prevent accidental contact. [6] : 3 

The task force had anticipated that a requirements and specification document would be published by the end of 2021. [4] In August 2021, prototype connectors were tested at up to 3.75 megawatts. [10] MCS connector version 3.2 was adopted in December 2021. [6] : 3  CharIN intends to complete the specification document by 2024, [1] which is planned to be in a state that is ready to be adopted by ISO and IEC as a global standard. [11] In preparation, SAE International began developing the draft MCS standards into the J3271 requirements in December 2021; [12] in parallel, the IEC began developing standard 63379 in Spring 2021. [13]

The final standard is expected to be resolved in 2024. [14] There is an open point in testing interference immunity of the PLC connection, otherwise the communication would need to switch to a CAN connection on the same pilot pins.[ citation needed ] Additionally the protocol on the PLC connection should support TCP/IP, so that ISO 15118 services have a direct connection to the vehicle electronics (Vehicle-To-Grid, Plug-N-Charge). [15]

Specific implementations

Lilium GmbH announced in October 2021 that forthcoming VTOL Lilium Jets would be fitted with MCS for charging. [16] Charging stations with MCS connectors will be delivered by ABB in 2024. [17] ABB charging stations have been operated at interoperability testing events. [18]

Three truck charging stations using a pre-standardized version of MCS will be built and operated in the Swedish project E-Charge. The chargers will be installed on three different locations in southern Sweden and will be used by four authentic logistics flows during a year's time starting in Q1 2024. The electric trucks will be provided by Scania and Volvo while the chargers will be provided by ABB. [19]

The German national project „Hochleistungsladen im Lkw-Fernverkehr“, commonly referred to as the HoLa project (from German Hochleistungs-Ladepark, literally high capacity charging park for the charging sites), [20] will build four new truck charging stations along the Autobahn A2 from Berlin, Germany to Duisburg, Germany. Each station will be equipped initially with two 600 kW stations starting in June 2022, and will be upgraded to 1 Megawatt using MCS in fall 2023. The chargers will be built by Heliox. [21]

The German Association of the Automotive Industry (VDA) published the "Masterplan Ladeinfrastruktur 2.0" in February 2022 in which they proposed to extend the Deutschlandnetz state-funded charging network into a "Deutschlandnetz für Lkw" (national fast-charging network for trucks). Whereas the current plan requires 200 kW per charging point using CCS, the next phase will require 700 kW per charging point using MCS. [22]

In January 2023 an early Tesla Semi was spotted with version 2 of the MCS charging port. [23] [24]

Kempower will deliver the first MCS chargers in late 2024 to a site in Sweden [25]

ABB will deliver charging stations with 1200 kW in 2025 which will be used in the pilot projects as planned in 2024. [26]

Pilot projects started in 2024. In March, an MAN eTruck was charged with 1000 A at 700 kW at an ABB charging station. [27] [28] In April, a Mercedes-Benz eActross 600was charged with 1250 A at 1000 kW at an ABB charging station. [29] In April, two eActross were delivered to the test client Contargo. [30] Contargo had announced to build its own network of truck fast chargers, specifically at its company sites in Duisburg, Voerde-Emmelsum, Emmerich, Frankfurt-Ost, Industriepark Frankfurt-Höchst, Gustavsburg, Hamburg, Karlsruhe, Koblenz, Ludwigshafen, Mannheim, Neuss, Weil am Rhein and Wörth. [31] In June, Milence openend its first truck charging park in the port of Antwerpen-Brügge, not including an MCS plug however. [32] In June, Shell opened a public truck fast charger with CCS and MCS at its ETCA campus in Amsterdam. [33] In July, E.On and MAN announced that they would set up publicly available fast chargers for trucks at MAN service centers by the end of 2025, with the first going into operation in 2024. 125 of the 170 locations are in Germany, the others in Austria, Great Britain, Denmark, Italy, Poland, the Czech Republic and Hungary. Here, too, they are starting with 400 kW CCS planning to convert to MCS later. [34]

Design requirements

Key requirements include: [4]

MCS is intended for Class 6, 7, and 8 commercial vehicles, initially with a primary focus on large trucks and busses, but potential MCS applications to the Aeronautics industry (e-VTOL, e-Planes, etc...) and Marine Industry (Tug-boats, e-Ferries, River Cargo vessels, etc...) exist. For road vehicles, the vehicle inlet should be placed on the driver's side of the vehicle (left side in North America), between the front and rear axles. [36] : 17 

A CCS Combo 1/Combo 2/SAE J3068 or ChaoJi inlet may also be fitted to the vehicle for compatibility and AC charging. Black & Veatch have designed prototype layout requirements for vehicle charging lanes. [37]

See also

Related Research Articles

Avcon is a company that manufactures charging interfaces for battery electric vehicles (EV). The lettering convention is Avcon for the company and AVCON (capitals) for the EV charging connector.

<span class="mw-page-title-main">Charging station</span> Installation for charging electric vehicles

A charging station, also known as a charge point, chargepoint, or electric vehicle supply equipment (EVSE), is a power supply device that supplies electrical power for recharging plug-in electric vehicles.

<span class="mw-page-title-main">SAE J1772</span> Electric vehicle charging connector in North America

SAE J1772, also known as a J plug or Type 1 connector after its international standard, IEC 62196 Type 1, is a North American standard for electrical connectors for electric vehicles maintained by SAE International under the formal title "SAE Surface Vehicle Recommended Practice J1772, SAE Electric Vehicle Conductive Charge Coupler".

<span class="mw-page-title-main">CHAdeMO</span> Fast charging method trade name

CHAdeMO is a fast-charging system for battery electric vehicles, developed in 2010 by the CHAdeMO Association, formed by the Tokyo Electric Power Company and five major Japanese automakers. The name is an abbreviation of "CHArge de MOve" and is derived from the Japanese phrase "o CHA deMO ikaga desuka" (お茶でもいかがですか), translating to English as "How about a cup of tea?", referring to the time it would take to charge a car.

<span class="mw-page-title-main">IEC 62196</span> International standards for vehicle charging technology

IEC 62196Plugs, socket-outlets, vehicle connectors and vehicle inlets – Conductive charging of electric vehicles is a series of international standards that define requirements and tests for plugs, socket-outlets, vehicle connectors and vehicle inlets for conductive charging of electric vehicles and is maintained by the technical subcommittee SC 23H “Plugs, Socket-outlets and Couplers for industrial and similar applications, and for Electric Vehicles” of the International Electrotechnical Commission (IEC).

<span class="mw-page-title-main">Conductive charging</span>

Conductive charging is conductive power transfer that replaces the conductive wires between the charger and the charged device with conductive contacts. Charging infrastructure in the form of a board or rail delivers the power to a charging device equipped with an appropriate receiver, or pickup. When the infrastructure recognizes a valid receiver it powers on, and power is transferred.

<span class="mw-page-title-main">Tesla Supercharger</span> Network of fast-charging stations

The Tesla Supercharger network is an electric vehicle fast charging network built and operated by American vehicle manufacturer Tesla, Inc.

<span class="mw-page-title-main">Combined Charging System</span> Electric vehicle charging standard

The Combined Charging System (CCS) is a standard for charging electric vehicles. It can use Combo 1 (CCS1) or Combo 2 (CCS2) connectors to provide power at up to 500 kilowatts (kW). These two connectors are extensions of the IEC 62196 Type 1 and Type 2 connectors, with two additional direct current (DC) contacts to allow high-power DC fast charging. In response to demand for faster charging, 400 kW CCS chargers have been deployed by charging networks and 700 kW CCS chargers have been demonstrated.

<span class="mw-page-title-main">Type 2 connector</span> Electric vehicle charging connector in Europe

The IEC 62196-2 Type 2 connector is used for charging electric vehicles, mainly within Europe, as it was declared standard by the EU. Based on widespread red IEC 60309 three phase plugs with five pins, which come in different diameters according to maximum current, a single size was selected, as maximum possible power will be communicated to the car via two additional communication pins and by a simple resistor coding within the cable. The onboard charger inside the car has to limit the current accordingly.

<span class="mw-page-title-main">ISO 15118</span> Proposed standard for vehicle-to-grid

ISO 15118Road vehicles -- Vehicle to grid communication interface is a proposed international standard defining a vehicle to grid (V2G) communication interface for bi-directional charging/discharging of electric vehicles. The standard provides multiple use cases like secure communication, smart charging and the Plug & Charge feature used by some electric vehicle networks.

IONITY operates as HPC charging network available for all electric vehicles across 24 countries in Europe. It's a joint venture of the car manufacturers BMW Group, Ford Motor Company, Hyundai Motor Group, Mercedes-Benz AG, and Volkswagen Group with Audi and Porsche, along with BlackRock's Climate Infrastructure Platform as a financial investor. The company's headquarters is in Munich, Germany, with additional offices in Dortmund and outside Norway’s capital Oslo. IONITY enables roaming from electric mobility service providers (EMSPs) and offers the Plug & Charge technology for selected vehicles, alongside convenient payment options and subscription offers.

<span class="mw-page-title-main">IEC 61851</span> International standards for vehicle charging technology

IEC 61851 is an international standard for electric vehicle conductive charging systems, parts of which are currently still under development(written 2017). IEC 61851 is one of the International Electrotechnical Commission's group of standards for electric road vehicles and electric industrial trucks and is the responsibility of IEC Technical Committee 69 (TC69).

<span class="mw-page-title-main">SAE J3068</span> Electric vehicle charging standard

SAE J3068 "Electric Vehicle Power Transfer System Using a Three-Phase Capable Coupler" is a North American recommended practice published and maintained by SAE International. J3068 defines electrical connectors and a control protocol for electric vehicles. It has the formal title "SAE Surface Vehicle Recommended Practice J3068". J3068 defines a system of conductive power transfer to an electric vehicle using a coupler capable of transferring single-phase and three-phase AC power as well as DC power, and defines a digital communication system for control. J3068 also specifies requirements for the vehicle inlet, supply equipment connector, mating housings and contacts.

<span class="mw-page-title-main">Electrify America</span> Electric vehicle charging network in U.S.

Electrify America, LLC is an electric vehicle DC fast-charging network in the United States, with more than 950 stations and over 4,250 DC fast charging connectors as of August 2024. It is a subsidiary of Volkswagen Group of America, established in late 2016 by the automaker as part of its efforts to offset emissions in the wake of the Volkswagen emissions scandal. Volkswagen, as part of its settlement following the "Dieselgate" emissions scandal, invested $2 billion in creating Electrify America. In June 2022, Siemens became a minority shareholder of the company. Electrify America supports the CCS and CHAdeMO connector types with plans to add NACS connectors starting in 2025. Electrify America has been the target of significant criticism for the perceived lack of reliability and maintenance of its stations.

The GB/T charging standard is a set of GB/T standards, primarily in the GB/T 20234 family, for electric vehicle AC and DC fast charging used in China. The standards were revised and updated most recently in 2015 by the Standardization Administration of China. The term is an abbreviation of 国标推荐 (guóbiāo/tuījiàn), translated as "recommended/voluntary national standard".

<span class="mw-page-title-main">ChaoJi</span> Electric vehicle charging standard

The ChaoJi connector, also referenced as CHAdeMO 3.0, is an ultra-high-power charging standard charging electric cars, released in 2020. The connector has a lemniscate shape (∞), with a flat bottom edge and is planned for charging battery electric vehicles at up to 900 kilowatts using direct current. The design incorporates backward compatibility with CHAdeMO and the GB/T DC-charging, using a dedicated inlet adapter for each system. The circuit interface of ChaoJi is also designed to be fully compatible with the Combined Charging System, also known as CCS.

<span class="mw-page-title-main">SAE J3105</span>

SAE J3105 is a recommended practice for automated connection devices (ACD) that mate chargers with battery electric buses and heavy-duty vehicles. The practice is maintained by the SAE International with the formal title "Electric Vehicle Power Transfer System Using Conductive Automated Connection Devices Recommended Practice", and was first issued in January 2020. It covers the general physical, electrical, functional, testing, and performance requirements for automated conductive DC power transfer systems intended for heavy duty vehicles, focusing primarily on transit buses.

<span class="mw-page-title-main">Type 3 connector</span> Electric vehicle charging connector in Europe

The IEC 62196 Type 3 connector is used for charging battery electric vehicles, mainly within France and Italy, as it was one of three AC plug standards described in IEC 62196-2. The Type 3 connector comes in two physical formats, Type 3A for single-phase (230V) and Type 3C for single- and three-phase (400V) alternating current (AC) power. Both have since been superseded by the Type 2 connector, the latter adopted as sole connector in 2013 by the European Union. The Type 1 connector is the corresponding AC connector standard used in North America, Japan, and South Korea.

<span class="mw-page-title-main">North American Charging System</span> Electric vehicle charging standard developed by Tesla

The North American Charging System (NACS), standardized as SAE J3400, is an electric vehicle (EV) charging connector standard maintained by SAE International. Developed by Tesla, Inc., it has been used by all North American market Tesla vehicles since 2021 and was opened for use by other manufacturers in November 2022. It is backwards compatible with the proprietary Tesla connectors made before 2021.

A fast charging network, or more specifically an HPC charging network, is a network of publicly accessible fast charging stations for electric vehicles. A fast charging network is a subtype of an electric vehicle charging network.

References

  1. 1 2 3 "CharIN shows MW charging system commercial EVs". Electrive. June 14, 2022. Retrieved 27 September 2022. The geometry of the charging plug, for example, was on display at the ABB eMobility stand. The design, long kept secret by CharIN, is triangular, with the tip pointing downwards. In the two upper corners are the (as expected) large receptacles for the two DC pins. The other, smaller pins for earthing and communication are placed in the middle and at the bottom. Since this is still a prototype, the final standard is not to be published until 2024, as mentioned above. CharIN says that the members of the organisation will present their respective products implementing MCS in the coming year. This means that the connector design should already be very close to the final specification.
  2. 1 2 3 "Industry Experts, Researchs Put Charging Systems for Electric Trucks to the Test" (Press release). National Renewable Energy Laboratory. August 30, 2021. Retrieved 27 September 2022. Building on previous lessons learned, this year's event focused on expanded evaluation to consider more real-world cases for safety and durability within the [Megawatt Charging System] standard, which specifies compatibility with up to 1,250 volts and 3,000 amps.
  3. 1 2 3 4 "CharIN HPCCV Task Force: High Power Plug Update". CharIN. April 2020. Retrieved 26 August 2021.
  4. 1 2 3 "Megawatt Charging System (MCS)". CharIN e.V. Retrieved 26 August 2021.
  5. ↑ Kocher, Rustam (2019-06-11). "Standardization Task Force update" (PDF). CharIN High Power Commercial Vehicle Charging. Retrieved 2021-01-10.
  6. 1 2 3 Bohn, Theodore (April 12, 2022). "SAE J3271 Megawatt Charging System standard; part of MW+ multiport electric vehicle charging for everything that 'rolls, flies or floats'". EPRI Bus & Truck. Retrieved 8 June 2022.
  7. ↑ "The CharIN path to Megawatt Charging (MCS): Successful connector test event at NREL" (Press release). 2020-10-13. Retrieved 2021-01-10. On September 23–24, 2020 … Fit and ergonomics evaluation of the MCS connector and inlet … At the facilities of National Renewable Energy Laboratory (NREL).
  8. ↑ "NREL-Hosted Event Supports Industry Development of Megawatt Charging System Connectors" (Press release). NREL. 2020-10-12. Retrieved 2021-01-10. Megawatt Charging System (MCS), a new charging standard for medium- and heavy-duty electric vehicles … enabled seven vehicle inlets and 11 charger connectors to test their designs together. … high-current nature of this system presents unique challenges to minimize cable length to improve efficiency and reduce thermal cooling … test matrix covering all connector and inlet combinations. … CharIN group has identified a list of priority requirements for a new high-power bidirectional charging system, including compatibility with up to 1,500 volts and 3,000 amps.
  9. ↑ Meintz, Andrew (June 24, 2021). "Charging INfrastructure Technologies: Development of a Multiport, >1 MW Charging System for Medium- and Heavy-Duty Electric Vehicles" (PDF). National Renewable Energy Laboratory. Retrieved 26 August 2021.
  10. ↑ Industry Experts, Researchers Put Charging Systems for Electric Trucks to the Test. News (Report). National Renewable Energy Laboratory. 2021-08-03. Retrieved 2021-10-11.
  11. ↑ "Megawatt charging in sight" (Press release). Scania. July 7, 2022. Retrieved 27 September 2022. 'To make things as easy as possible, MCS is based on a global agreement on technical specifications, with support of a large portion of the industry, where CharIN has been the perfect incubator delivering ready concept of MCS that now are handed over to become ISO and IEC standards,' says Johan Lindström, Technical Manager VCB Vehicle Technology, Scania.
  12. ↑ "Megawatt Charging System for Electric Vehicles: J3271". SAE International. December 15, 2021. Retrieved 3 May 2022.
  13. ↑ Bernd Horrmeyer (December 2, 2021). "Megawatt Charging System: Standardization supports global electrification of heavy-duty traffic" (Interview). Interviewed by Gürkan Balcioglu. DKE Technology.
  14. ↑ Kane, Mark (2022-06-15). "CharIN Officially Launches The Megawatt Charging System (MCS)". Inside EV.
  15. ↑ "CharIN Whitepaper Megawatt Charging System (MCS) – Recommendations and requirements for MCS related standards bodies and solution suppliers – Version 1.0" (PDF). CharIN. 2022-11-24.
  16. ↑ "ABB and Lilium team to revolutionize charging infrastructure for regional air travel" (Press release). ABB. 2021-10-13.
  17. ↑ "Lilium Partners with ABB for Charging Infrastructure". Transport UP. 2022-02-22.
  18. ↑ "CharIN Launches Megawatt Charging System (MCS) In North America". InsideEVs. Retrieved 2022-10-29.
  19. ↑ "E-Charge | Lindholmen Science Park".
  20. ↑ "HoLa – High performance charging for long-haul trucking". Hochleistungsladen Lkw-Fernverkehr. Retrieved 8 June 2022.
  21. ↑ "Heliox: From coarse to fine adjustment of the megawatt charge". 2021-10-16.
  22. ↑ "Aufbau E-Ladenetz für Nutzfahrzeuge fokussieren – 5 Mrd. Booster-Förderung bis 2025" (Press release). VDA - Verband der deutschen Automobilindustrie. 2022-03-11.
  23. ↑ u/wroniec498 (2023-01-26). "Tesla Semi charging port (mcs2)". Reddit. Archived from the original on 2023-01-26.{{cite web}}: CS1 maint: numeric names: authors list (link)
  24. ↑ Tesla Megacharger! Visiting A DCFC Location With Over 100 EV Chargers. Welcome To Baker, CA, 28 July 2023, retrieved 2023-07-30
  25. ↑ "Kempower and Virta to deliver megawatt charging system for electric cars and trucks to Hedin Supercharge's public charging hub in Linköping, Sweden". Kempower. Retrieved 2024-11-22.
  26. ↑ ABB E-mobility stellt neuen HPC A400 vor: Kommt jetzt das wahre "LADEVERGNÜGEN" on YouTube 2024-06-22
  27. ↑ "ABB E-mobility und MAN demonstrieren erstmals Megawatt-Charging am eTruck". Pressemitteilung. MAN Trucks & Bus. 2024-03-21.
  28. ↑ Cora Werwitzke (2024-03-22). "Megawattladen: MAN eTruck zieht sich 700 kW an MCS-Prototypgerät von ABB". Electrive.
  29. ↑ Cora Werwitzke (2024-04-22). "Lade-Demonstration: Mercedes-Benz eActros 600 zieht sich ein Megawatt". Electrive.
  30. ↑ Sebastian Schaal (2024-04-18). "Mercedes eActros 600 startet in die Kundenerprobung". Electrive.
  31. ↑ Cora Werwitzke (2023-02-09). "Contargo lässt privates Ladenetz für 33 E-Lkw bauen". Electrive.
  32. ↑ Thomas Burger (2024-06-13). "Ladeinfrastruktur: Milence eröffnet Ladepark in Antwerpen". Verkehrsrundschaue.
  33. ↑ Chris Rendal (2024-06-20). "Shell to launch megawatt charging system for trucks and ships". Electrive.
  34. ↑ Sebastian Schaal (2024-07-11). "E.On und MAN bauen 400 Lkw-Schnellladepunkte". Electrive.
  35. ↑ Paulraj, Pon. "Megawatt Charging System Communication (MCS) Communication Topology | What changes on PLC, ISO 15118 and SLAC". E-Mobility Simplified | Basics of Electric Vehicles and Charging. Retrieved 2023-01-11.
  36. ↑ Truemner, Russell (2019-02-18). "Task Force Aggregated Requirements" (PDF). CharIN High Power Commercial Vehicle Charging. Archived from the original (PDF) on July 10, 2019. Retrieved 2021-01-10.
  37. ↑ Pollom, Russell E. (May 5, 2021). "Black & Veatch Layouts for MCS Working Group" (PDF). Charging Interface Inititative (CharIN) Megawatt Charging System Task Force. Retrieved 26 August 2021.
This page is based on this Wikipedia article
Text is available under the CC BY-SA 4.0 license; additional terms may apply.
Images, videos and audio are available under their respective licenses.