IEC 61851 is an international standard for electric vehicle conductive charging systems, parts of which are currently still under development(written 2017). IEC 61851 is one of the International Electrotechnical Commission's group of standards for electric road vehicles and electric industrial trucks and is the responsibility of IEC Technical Committee 69 (TC69). [1]
IEC 61851 consists of the following parts, detailed in separate IEC 61851 standard documents:
IEC 61851-1 defines four modes of charging:
| Mode | Diagram | Limits | Supply & Interface | RCD Protection | Applications | Notes | ||
|---|---|---|---|---|---|---|---|---|
| Phases | Current | Voltage | ||||||
| 1 |  EV connected directly to AC grid | 1φ | 16A | 250V | AC, non-dedicated |  | electric bikes & scooters | Direct connection of vehicle to conventional electrical outlets. Not allowed in the US, Israel, and England; prohibited for public charging by Italy; restricted in Switzerland, Denmark, Norway, and Germany. |
| 3φ | 16A | 480V | ||||||
| 2 |  EV connected to AC grid through cable incorporating RCD protection | 1φ | 32A | 250V | AC, non-dedicated |  | "slow AC" | Requires control box between vehicle and electrical outlet incorporating RCD protection. Prohibited for public charging by Italy; restricted in US, Canada, Switzerland, Denmark, France, and Norway. Typical portable / "emergency" charger. |
| 3φ | 32A | 480V | ||||||
| 3 |  EVSE connected to AC grid, supplies EV using tethered cable or socket-outlet with bidirectional communication | 1φ | 32A | 250V | AC, dedicated (IEC 62196-2) | | "slow and quick AC" | EVSE permanently connected to electrical grid; includes RCD protection and bidirectional (EVSE/EV) communication. Typical public AC charger installation. Tethered (cable permanently attached) & untethered (dedicated socket outlet only) configurations. |
| 3φ | 32A | 480V | ||||||
| 4 |  EVSE rectifies AC grid & supplies DC power to EV using tethered cable with bidirectional communication | – | 200A | 400V | DC, dedicated (IEC 62196-3) | | "fast DC" | Current conversion handled by EVSE, not EV. |
In electrical engineering, low voltage is a relative term, the definition varying by context. Different definitions are used in electric power transmission and distribution, compared with electronics design. Electrical safety codes define "low voltage" circuits that are exempt from the protection required at higher voltages. These definitions vary by country and specific codes or regulations.
A charging station, also known as a charge point or electric vehicle supply equipment (EVSE), is a power supply device that supplies electrical power for recharging plug-in electric vehicles.
SAE J1772, also known as a J plug or Type 1 connector after its international standard, IEC 62196 Type 1, is a North American standard for electrical connectors for electric vehicles maintained by SAE International under the formal title "SAE Surface Vehicle Recommended Practice J1772, SAE Electric Vehicle Conductive Charge Coupler".
CHAdeMO is a fast-charging system for battery electric vehicles, developed in 2010 by the CHAdeMO Association, formed by the Tokyo Electric Power Company and five major Japanese automakers. The name is an abbreviation of "CHArge de MOve" and is derived from the Japanese phrase "o CHA deMO ikaga desuka" (お茶でもいかがですか), translating to English as "How about a cup of tea?", referring to the time it would take to charge a car.
IEC 62196Plugs, socket-outlets, vehicle connectors and vehicle inlets – Conductive charging of electric vehicles is a series of international standards that define requirements and tests for plugs, socket-outlets, vehicle connectors and vehicle inlets for conductive charging of electric vehicles and is maintained by the technical subcommittee SC 23H “Plugs, Socket-outlets and Couplers for industrial and similar applications, and for Electric Vehicles” of the International Electrotechnical Commission (IEC).
The Open Charge Point Protocol (OCPP) is an application protocol for communication between Electric vehicle (EV) charging stations and a central management system, also known as a charging station network, similar to cell phones and cell phone networks. The original version was written by Joury de Reuver and Franc Buve.
The Combined Charging System (CCS) is a standard for charging electric vehicles. It can use Combo 1 (CCS1) or Combo 2 (CCS2) connectors to provide power at up to 350 kilowatts (kW) . These two connectors are extensions of the IEC 62196 Type 1 and Type 2 connectors, with two additional direct current (DC) contacts to allow high-power DC fast charging. In response to demand for faster charging, 400 kW CCS chargers have been deployed by charging networks and 700 kW CCS chargers have been demonstrated.
The IEC 62196 Type 2 connector is used for charging electric vehicles, mainly within Europe, as it was declared standard by the EU. Based on widespread red IEC 60309 three phase plugs with five pins, which come in different diameters according to maximum current, a single size was selected, as maximum possible power will be communicated to the car via two additional communication pins and by a simple resistor coding within the cable. The onboard charger inside the car has to limit the current accordingly.
The electric vehicle industry in India is slowly growing. The central and state governments have implemented schemes and incentives to promote electric mobility, and have introduced regulations and standards. Although India would benefit from converting its transport from internal combustion (IC) engines to electric motors, challenges include a lack of charging infrastructure, high initial cost and a lack of renewable energy. E-commerce companies, car manufacturers, app-based transport network companies and mobility-solution providers have entered the sector, however, and are slowly building electric-car capacity and visibility.
IEC 63110 is an international standard defining a protocol for the management of electric vehicles charging and discharging infrastructures, which is currently under development. IEC 63110 is one of the International Electrotechnical Commission's group of standards for electric road vehicles and electric industrial trucks, and is the responsibility of Joint Working Group 11 (JWG11) of IEC Technical Committee 69 (TC69).
ISO 15118Road vehicles -- Vehicle to grid communication interface is a proposed international standard defining a vehicle to grid (V2G) communication interface for bi-directional charging/discharging of electric vehicles. The standard provides multiple use cases like secure communication, smart charging and the Plug & Charge feature used by some electric vehicle networks.
SAE J3068 "Electric Vehicle Power Transfer System Using a Three-Phase Capable Coupler" is a North American recommended practice published and maintained by SAE International. J3068 defines electrical connectors and a control protocol for electric vehicles. It has the formal title "SAE Surface Vehicle Recommended Practice J3068". J3068 defines a system of conductive power transfer to an electric vehicle using a coupler capable of transferring single-phase and three-phase AC power as well as DC power, and defines a digital communication system for control. J3068 also specifies requirements for the vehicle inlet, supply equipment connector, mating housings and contacts.
The GB/T charging standard is a set of GB/T standards, primarily in the GB/T 20234 family, for electric vehicle AC and DC fast charging used in China. The standards were revised and updated most recently in 2015 by the Standardization Administration of China. The term is an abbreviation of 国标推荐 (guóbiāo/tuījiàn), translated as "recommended/voluntary national standard".
The ChaoJi connector, also referenced as CHAdeMO 3.0, is an ultra-high-power charging standard charging electric cars, released in 2020. The connector has a lemniscate shape (∞), with a flat bottom edge and is planned for charging battery electric vehicles at up to 900 kilowatts using direct current. The design incorporates backward compatibility with CHAdeMO and the GB/T DC-charging, using a dedicated inlet adapter for each system. The circuit interface of ChaoJi is also designed to be fully compatible with the Combined Charging System, also known as CCS.
SAE J3105 is a recommended practice for automated connection devices (ACD) that mate chargers with battery electric buses and heavy-duty vehicles. The practice is maintained by the SAE International with the formal title "Electric Vehicle Power Transfer System Using Conductive Automated Connection Devices Recommended Practice", and was first issued in January 2020. It covers the general physical, electrical, functional, testing, and performance requirements for automated conductive DC power transfer systems intended for heavy duty vehicles, focusing primarily on transit buses.
The Megawatt Charging System (MCS) is a charging connector under development for large battery electric vehicles. The connector will be rated for charging at a maximum rate of 3.75 megawatts.
IEC 63382 is an international standard defining a protocol for the management of distributed energy storage systems based on electric vehicles, which is currently under development. IEC 63382 is one of the International Electrotechnical Commission's group of standards for electric road vehicles and electric industrial trucks, and is the responsibility of Joint Working Group 15 (JWG15) of IEC Technical Committee 69 (TC69).
The IEC 62196 Type 3 connector is used for charging battery electric vehicles, mainly within France and Italy, as it was one of three AC plug standards described in IEC 62196-2. The Type 3 connector comes in two physical formats, Type 3A for single-phase (230V) and Type 3C for single- and three-phase (400V) alternating current (AC) power. Both have since been superseded by the Type 2 connector, the latter adopted as sole connector in 2013 by the European Union. The Type 1 connector is the corresponding AC connector standard used in North America, Japan, and South Korea.
| Vehicle |   | ||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|
| Type | |||||||||||
| Charging |
| ||||||||||
| By location | |||||||||||