 |
| NZR D class | |||||||||||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
 Trial run of Clayton D class locomotive No 1 at Silverstream | |||||||||||||||||||||
| |||||||||||||||||||||
| |||||||||||||||||||||
| |||||||||||||||||||||
The NZR D class of 1929 comprised one 0-4-0 tank locomotive that was built for the New Zealand Railways Department by the Clayton Wagons Ltd in Lincoln, England.
| |
| NZR D class | |||||||||||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| Trial run of Clayton D class locomotive No 1 at Silverstream | |||||||||||||||||||||
| |||||||||||||||||||||
| |||||||||||||||||||||
| |||||||||||||||||||||
The NZR D class of 1929 comprised one 0-4-0 tank locomotive that was built for the New Zealand Railways Department by the Clayton Wagons Ltd in Lincoln, England.
Originally, D 1 was purchased for railcar type service but it was not successful. It had a White-Forster type boiler designed for a working pressure of 300 psi (2,068 kPa), had four vertical cylinders housed in the rear of the cab and was high geared. At a normal engine speed of 400 rpm, the unit was calculated to develop 200 horsepower (150 kW). The engine drove a central transverse jackshaft through reduction gearing, the drive from the jackshaft being transmitted to the wheels through conventional side rods.
On arrival in New Zealand, D 1 was found to be more than 25 percent heavier than the specified maximum of 20 long tons (20.3 t; 22.4 short tons) and after trials in Wellington was allocated for use as a shunting engine at the Ōtāhuhu workshops. However it never proved satisfactory and was written off in 1936 and scrapped and D 1 did not survive to be preserved.
The NZR A class of 1873 consisted of three types of steam locomotives used on New Zealand's railway network of similar specification but differing detail. The first and most numerous were from the Dübs and Company, the next from the Wellington firm E.W. Mills Lion Foundry, and the last from the Scottish firm of Shanks. The specifications are for the Dubs Yorkshire engines.
The NZR A class were a class of steam locomotives built in 1906 with a 4-6-2 wheel arrangement for the New Zealand Railways Department (NZR). The class should not be confused with the older and more obscure A class of 1873. They were designed by the NZR's Chief Mechanical Engineer, A. L. Beattie and his Chief Draughtsman, G. A. Pearson to replace less powerful locomotives struggling with increasing loads on the South Island Main Trunk Railway, and in anticipation of the traffic volumes that would be created upon the completion of the North Island Main Trunk railway.
The NZR AA class consisted of ten steam locomotives built by Baldwin Locomotive Works in 1914 to an order by Chief Mechanical Engineer, H. H. Jackson for operation on New Zealand's national rail network.
The NZR NA class was a class of two steam locomotives that operated on the privately owned Wellington and Manawatu Railway (WMR) and then the publicly owned New Zealand Railways (NZR). Ordered by the WMR to operate on its line up the west coast of the North Island north of Wellington, the first was built in 1894 by the Baldwin Locomotive Works and entered service that year as WMR No. 14. In 1896, a second locomotive that was slightly more powerful was ordered from Baldwin, and it entered service in October 1897. The engines were similar to the two members of the N class ordered in 1891, except they were heavier and more powerful. They were Vauclain compound locomotives.
The NZR B class of 1899 was a class of steam locomotives that operated on New Zealand's national rail network. An earlier B class of Double Fairlies had entered service in 1874, but as they had departed from the ownership of the New Zealand Railways (NZR) by the end of 1896, the B classification was free to be re-used. Despite early difficulties, they were amongst NZR's most influential designs.
The BA class was a class of steam locomotive built by the New Zealand Railways Department (NZR) for use on New Zealand's national rail network. The first BA entered service in November 1911, with the last of the 11 class members introduced on 14 May 1913.
The NZR BB class of steam locomotives comprised 30 engines operated by the New Zealand Railways (NZR) in the North Island of New Zealand. Ordered to replace smaller locomotives of several classes in the North Island, they were similar in design and appearance to the preceding B and BA classes. The first BB class locomotive entered service in February 1915, with the last to commence operations doing so on 8 March 1917. All were built by A & G Price Ltd of Thames, New Zealand, and as their cylinders had a larger diameter than the B and BA locomotives they were capable of generating more power to haul heavier trains. The most visible difference however was the roundtop firebox in place of the preceding classes Belpaire design. The BB class could haul up to 700 long tons of freight on a level railway line, though they were limited to a top speed of around 40 mph (64 km/h).
The BC class comprised a single steam locomotive that operated on New Zealand's national rail network. Built for the Wellington and Manawatu Railway (WMR) and classified simply as No.17, it passed into the ownership of the New Zealand Railways Department (NZR) when the government purchased the WMR in December 1908, and it was then that it acquired the BC classification as BC 463.
The NZR G class was a type of Garratt locomotives used in New Zealand, later rebuilt as Pacific type locomotives. They were the only Garratt type steam locomotives ever used by the New Zealand Railways (NZR). They were ordered to deal with traffic growth over the heavy gradients of the North Island Main Trunk (NIMT) and to do away with the use of banking engines on steep grades. They were one of the few Garratt designs to employ six cylinders. A mechanical stoker was used to feed coal into the locomotive. The locomotives lasted longer in rebuilt form as standard Pacific locomotives than they did as Garratts, but their numerous mechanical issues lead to their final withdrawal following a union ban on their use in 1956.
The NZR H class steam locomotive was a unique class of Fell locomotive used by New Zealand Railways (NZR) on the Rimutaka Incline, the 3-mile (4.8 km) section of 1 in 15 gradient between Cross Creek and Summit, over the Rimutaka Ranges.
The NZR R class was a class of early 0-6-4T single Fairlie steam locomotives operated by New Zealand's Railways Department (NZR) between 1879 and 1936.
The NZR Q class was an important steam locomotive class not only in the history of New Zealand's railway network but also in worldwide railways in general. Designed by New Zealand Government Railways' (NZR) Chief Mechanical Engineer A. L. Beattie and ordered from the Baldwin Locomotive Works in 1901, they were the first locomotives in the world to be built with the wheel arrangement of 4-6-2. This wheel arrangement came to be known as the Pacific type after the voyage the completed locomotives had to make across the Pacific Ocean to New Zealand. A few instances of the 4-6-2 wheel arrangement are known to have existed prior to 1901, but these were all reconstructions of locomotives that were originally built with a different wheel arrangement, thereby making the thirteen members of the Q class the first "true" Pacifics in the world. The Pacific style went on to become arguably the most famous wheel arrangement in the world.
The New Zealand V class steam locomotive was used on New Zealand's railway network from 1885 onwards. They were operated by New Zealand Government Railways and the Wellington and Manawatu Railway Company.
The NZR UD class was a class of two 4-6-0 steam locomotives built by the Baldwin Locomotive Works in 1904 for the Wellington and Manawatu Railway Company. When that company was nationalised in 1908, they passed into the ownership of the New Zealand Railways and received the designation UD.
The NZR S class was a class of seven 0-6-4T single Fairlie steam locomotives operated by New Zealand's Railways Department (NZR) between 1882 and 1927.
The NZR DS class locomotive is a type of 16 diesel shunting locomotives built by the Vulcan Foundry and supplied by the Drewry Car Co from 1949–1955, for New Zealand Railways (NZR).
The NZR WJ class was a class of one steam locomotive built by Baldwin Locomotive Works for service on New Zealand's private Wellington and Manawatu Railway (WMR). She acquired the WJ classification when the publicly owned New Zealand Railways Department (NZR) purchased the WMR and its locomotive fleet in 1908.
The NZR M class were a series of four tank engines built in England for the Otago railways Bluff to Winton section. They were acquired by NZR in the late 1870s and rebuilt in the late 1880s. As rebuilt they were not very successful and were used in shunting duties until retirement in the 1920s.
The NZR Q class were a pair of 2-4-4T type tank engines built by Rogers Locomotive and Machine Works in New Jersey. They were similar, in appearance, to the earlier K class of the same manufacturer and were purchased by the Rakaia & Ashburton Forks Railway Company for working their newly constructed railway to Methven from Rakaia, which later became the Methven Branch.
The NZR UB class were a series of Ten Wheelers built by American manufacturers for New Zealand Railways (NZR) around the start of the twentieth century. Two batches were built by Baldwin in 1898 and 1901. The earlier engines had slide valves and inside Stephenson motion, the later had piston valves and Walschaerts valve gear, as well as a higher boiler pressure.
 | This steam locomotive-related article is a stub. You can help Wikipedia by expanding it. |
