Nieuport 17bis

Last updated
Nieuport 17bis and 23bis
Nieuport 17bis in French markings, front quarter.jpg
Role Fighter
National origin France
Manufacturer Nieuport
DesignerGustave Delage
Built by Nieuport & General Aircraft
Introduction1 February 1917 [1]
StatusRetired
Primary users Royal Naval Air Service
Royal Flying Corps
Aéronautique Militaire
Number built84+ 17bis and 17 23bis
Developed from Nieuport 17
Variants Nieuport 24

The Nieuport 17bis C.1 (or Nieuport XVIIbis C.1 in contemporary sources) was a World War I French single-seat sesquiplane fighter that was produced under licence in the United Kingdom in small numbers for the Royal Naval Air Service.

Contents

Development

Nieuport 17bis prototype in French markings. The forward rake of the front cabane struts is evident Nieuport 17bis in French markings, right side.jpg
Nieuport 17bis prototype in French markings. The forward rake of the front cabane struts is evident
Nieuport 17bis from above showing off the square ailerons. Nieuport 17bis from above.jpg
Nieuport 17bis from above showing off the square ailerons.

The Nieuport 17bis designation was initially used by Nieuport for a Nieuport 11 variant that had been retrofitted with the wings and side fairings from a Nieuport 17, however this type was not produced in any numbers and the designation was reused.

The Nieuport 17bis was the first of the vee strut scouts to feature a fully streamlined fuselage, with longitudinal stringers to fair out the shape. Other than the changes to the fuselage, minimal alterations were made, and unlike the later 24, 24bis and 27, the flying surfaces remained the same as used on the 17, as was much of the internal structure. Unlike the 17, or any of the other Vee strutters, it had the Vickers Machine Gun offset to the port (left) side of the centerline. [2] Due to shortages of Le Rhône rotaries, they were fitted with the 130 hp (97 kW) Clerget 9B rotary instead of the 25 kg (55 lb) lighter 120 hp (89 kW) Le Rhône 9J used in most of the other Nieuport single seat scouts. A few examples were fitted with the lower powered 110 hp (82 kW) Clerget 9Z. As a result of the Clerget's slightly greater diameter, the cowling was ballooned out slightly to provide clearance. [2]

The majority of Nieuport 17bis were operated by 6 (Naval) Squadron, who tested them against a Sopwith Triplane and a Sopwith Camel. It was found to have similar manoeuvrability to the Triplane and have a higher dive speed, but was slightly slower at altitude and had heavier controls. [3] Climb rates varied, and in the first test the 17bis outclimbed the Triplane by a significant margin, however in the second test the times to altitude were identical between the two types. [3] The Camel was marginally faster at sea level but had a lower rate of climb while the speed advantage gradually disappeared with altitude. [4] Adding a Lewis machine gun to the Vickers reduced the climb rate, and increased the time it took to climb to 12,000 ft (3,700 m) by 2 minutes. [5] Initial reports were impressive, but the Clerget engines lost power quickly between overhauls, and the problem was worse with the British built engines. Many pilots tried to have French-built engines in their aircraft. [6] Some aircraft were also delivered to units with incorrect propellers, which also hampered performance. [6]

Triplane

At least one 17bis was built as a triplane in the same manner as the Nieuport 17 triplanes, with the wings staggered with the middle wing furthest forward, and the lowest wing furthest aft. Flight testing discovered that it was longitudinally unstable but handled well otherwise, but the concept was not pursued further.

Nieuport 23bis

The Nieuport 23bis was a later but in many ways a similar development to the 17bis and was the result of the RFC's desperation to get as many aircraft as possible into front line service, but only 17 were produced and all went to the RFC. [7] It combined the flying surfaces including the tail of the 23 with the fuselage of the 24bis, and was fitted with other Nieuport 23 parts, such as an earlier form of cowling. [8] Unlike the 17bis, it retained the Le Rhône normally used by Nieuport scouts.

Distinguishing features

The 17, 17bis, 23 and 23bis flying surfaces had the front spar positioned further forward than on the later types. [9] Aside from the lack of a plywood leading edge to the wing, the key identifying feature was the rake of the forward cabane struts connecting the top wing to the fuselage. [8] On the 17, 17bis, 21, 23 and 23bis, the cabane struts were angled forward from the fuselage, while on the 24, 24bis, 25 and 27, they were angled aft. [9] Both the 17bis and the 23bis used the square ailerons, rather than the rounded ailerons used on production versions of the later types. [7]

Operational history

Aside from one example being flown by Charles Nungesser and marked with his personal serial number N1895, the Nieuport 17bis saw little service with the French Aéronautique Militaire.

The Royal Naval Air Service (RNAS) was the primary operator of the Nieuport 17bis, with 6 (Naval) Squadron being the only unit wholly equipped with the type. It primarily replaced the obsolete Nieuport 10 and the Nieuport 11 and would in turn be replaced by the Sopwith Camel. The RNAS received 82 examples, of which 32 were from Nieuport (including 1 triplane) and 50 from Nieuport & General Aircraft who built them under licence in the UK. [6] The British-built examples were delivered so slowly that the type had been declared obsolete before most were even delivered and only 4 were known to have been used operationally. As a consequence, most were never removed from their crates, and were scrapped without having been flown. The initial order of 50 had been reduced from 100, and an additional order of 100 from Nieuport & General was cancelled outright. [10] After having been withdrawn from front line duties beginning in June 1917, some were used for training in the UK, where they were flown unarmed. Those that were built in France were silver doped, while those built in the UK were camouflaged.

The Royal Flying Corps never operated the 17bis, however it did receive 17 of the similar Nieuport 23bis that had been misidentified until recently. [9]

Variants

Operators

Flag of the United Kingdom.svg  United Kingdom
Flag of France.svg  France

Specifications (Nieuport 17bis)

3-view drawing of British-built Nieuport 17bis Nieuport 17bis (Nieuport & General) French First World War single seat fighter colourized drawing.jpg
3-view drawing of British-built Nieuport 17bis
Nieuport Type N airfoil drawings Nieuport 17 Type N airfoils.jpg
Nieuport Type N airfoil drawings

Data from Tanner, 1976, p.179 (dimensions only), Davilla, 1997, p.385

General characteristics

Performance

Armament

See also

Related development

Related lists

Related Research Articles

<span class="mw-page-title-main">Sopwith Camel</span> British WW1 biplane fighter aircraft

The Sopwith Camel is a British First World War single-seat biplane fighter aircraft that was introduced on the Western Front in 1917. It was developed by the Sopwith Aviation Company as a successor to the Sopwith Pup and became one of the best known fighter aircraft of the Great War.

<span class="mw-page-title-main">Sopwith Pup</span> British WW1 biplane fighter aircraft

The Sopwith Pup is a British single-seater biplane fighter aircraft built by the Sopwith Aviation Company. It entered service with the Royal Naval Air Service and the Royal Flying Corps in the autumn of 1916. With pleasant flying characteristics and good manoeuvrability, the aircraft proved very successful. The Pup was eventually outclassed by newer German fighters, but it was not completely replaced on the Western Front until the end of 1917. Remaining Pups were relegated to Home Defence and training units. The Pup's docile flying characteristics also made it ideal for use in aircraft carrier deck landing and takeoff experiments and training.

<span class="mw-page-title-main">Nieuport</span> Defunct French aircraft manufacturer

Nieuport, later Nieuport-Delage, was a French aeroplane company that primarily built racing aircraft before World War I and fighter aircraft during World War I and between the wars.

<span class="mw-page-title-main">Nieuport 17</span> French WW1 fighter aircraft

The Nieuport 17 C.1 was a French sesquiplane fighter designed and manufactured by the Nieuport company during World War I. An improvement over the Nieuport 11, it was a little larger than earlier Nieuports and better adapted to the more powerful engine than the interim Nieuport 16. Aside from early examples, it had the new Alkan-Hamy synchronization gear, permitting the use of a fuselage-mounted synchronised Vickers gun firing through the propeller disc.

<span class="mw-page-title-main">Sopwith Snipe</span> British WW1 biplane fighter aircraft

The Sopwith 7F.1 Snipe was a British single-seat biplane fighter of the Royal Air Force (RAF). It was designed and built by the Sopwith Aviation Company during the First World War, and came into squadron service a few weeks before the end of the conflict, in late 1918.

<span class="mw-page-title-main">Sopwith Triplane</span> British WW1 triplane fighter aircraft

The Sopwith Triplane was a British single seat fighter aircraft designed and manufactured by the Sopwith Aviation Company during the First World War. It has the distinction of being the first military triplane to see operational service.

<span class="mw-page-title-main">Sopwith 1½ Strutter</span> British WW1 biplane fighter, bomber and reconnaissance aircraft

The Sopwith 1+12 Strutter was a British single- or two-seat multi-role biplane aircraft of the First World War. It was the first British two-seat tractor fighter and the first British aircraft to enter service with a synchronised machine gun. It was given the name 1+12 Strutter because of the long and short cabane struts that supported the top wing. The type was operated by both British air services and was in widespread but lacklustre service with the French Aéronautique Militaire.

<span class="mw-page-title-main">Nieuport 27</span> French WW1 fighter aircraft

The Nieuport 27 was a World War I French sesquiplane fighter aircraft designed by Gustave Delage. The 27 was the last of the line of Nieuport "V-strut" single seat fighters that began with the Nieuport 10 of 1914. Operational examples supplemented the very similar Nieuport 24 and 24bis in operational squadrons in late 1917 and many would also be used as advanced trainers.

<span class="mw-page-title-main">Bristol Scout</span> Type of aircraft

The Bristol Scout was a single-seat rotary-engined biplane originally designed as a racing aircraft. Like similar fast, light aircraft of the period it was used by the RNAS and the RFC as a "scout", or fast reconnaissance type. It was one of the first single-seaters to be used as a fighter aircraft, although it was not possible to fit it with an effective forward-firing armament until the first British-designed gun synchronizers became available later in 1916, by which time the Scout was obsolescent. Single-seat fighters continued to be called "scouts" in British usage into the early 1920s.

<span class="mw-page-title-main">Nieuport 28</span> French WW1 fighter aircraft

The Nieuport 28 C.1, a French biplane fighter aircraft flown during World War I, was built by Nieuport and designed by Gustave Delage. Owing its lineage to the successful line of sesquiplane fighters that included the Nieuport 17, the Nieuport 28 continued a similar design philosophy of a lightweight and highly maneuverable aircraft.

<span class="mw-page-title-main">Airco DH.5</span> Type of aircraft

The Airco DH.5 was a British First World War single-seat biplane fighter aircraft. It was designed and manufactured at British aviation company Airco. Development was led by aircraft designer Geoffrey de Havilland as a replacement for the obsolete Airco DH.2.

<span class="mw-page-title-main">Vickers F.B.19</span> Type of aircraft

The Vickers F.B.19 was a British single-seat fighting scout of the First World War, developed from the Barnwell Bullet prototype, and sometimes known as the Vickers Bullet. It served with the Royal Flying Corps and the Imperial Russian Air Service, which subsequently led to the Red Air Force adopting it during the Russian Civil War.

<span class="mw-page-title-main">Armstrong Whitworth F.K.10</span> British WWI quadruplane fighter aircraft

The Armstrong Whitworth F.K.10 was a British two-seat quadruplane fighter aircraft built by Armstrong Whitworth during the First World War. While it was ordered in small numbers for the Royal Flying Corps and Royal Naval Air Service, it was not used operationally. It is one of the few quadruplane aircraft to reach production.

<span class="mw-page-title-main">Le Rhône 9J</span>

The Le Rhône 9J is a nine-cylinder rotary aircraft engine produced in France by Gnome et Rhône. Also known as the Le Rhône 110 hp in a reference to its nominal power rating, the engine was fitted to a number of military aircraft types of the First World War. Le Rhône 9J engines were produced under license in Great Britain by W.H. Allen Son & Company of Bedford, and in Germany by Motorenfabrik Oberursel where it was sold as the Oberursel Ur.II.

<span class="mw-page-title-main">Bristol M.1</span> Type of aircraft

The Bristol M.1 Monoplane Scout was a British monoplane fighter of the First World War. It holds the distinction of being the only British monoplane fighter to reach production during the conflict.

<span class="mw-page-title-main">Nieuport 12</span> French WW1 fighter and reconnaissance aircraft

The Nieuport 12 was a French sesquiplane reconnaissance, fighter aircraft and trainer used by France, Russia, Great Britain and the United States during World War I. Later production examples were built as trainers and served widely until the late 1920s.

<span class="mw-page-title-main">Nieuport 24</span> French WW1 fighter aircraft

The Nieuport 24 was a World War I French sesquiplane fighter aircraft designed by Gustave Delage as a development of the successful Nieuport 17.

<span class="mw-page-title-main">Clerget 9B</span>

The Clerget 9B was a nine-cylinder rotary aircraft engine of the World War I era designed by Pierre Clerget. Manufactured in both France and Great Britain, it was used on such aircraft as the Sopwith Camel. The Clerget 9Bf was an increased stroke version.

<span class="mw-page-title-main">Sopwith Three-seater</span> Type of aircraft

The Sopwith Three-seater was a British aircraft designed and built prior to the start of the First World War. One of the first aircraft built by the Sopwith Aviation Company, it was operated by both the Royal Naval Air Service (RNAS) and the Royal Flying Corps (RFC), being used briefly over Belgium by the RNAS following the start of the War.

<span class="mw-page-title-main">Nieuport 16</span> French WW1 fighter aircraft

The Nieuport 16 C.1 was a French World War I single-seat sesquiplane fighter aircraft, designed by Gustave Delage as a development of the Nieuport 11 with a more powerful engine. The Nieuport 16's service life coincided with the period when the first air-to-air rockets, the Le Prieur rocket, were used most frequently, and the type has a closer association with them than any other aircraft.

References

Notes

  1. per British rigging instructions, French aircraft were rigged with 3° 20' of wing sweep.

Citations

  1. Westrop, 2006, p.17
  2. 1 2 Westrop, 2006, p.158
  3. 1 2 Westrop, 2006, p.25
  4. Westrop, 2006, p.30
  5. Westrop, 2006, p.31
  6. 1 2 3 4 5 Westrop, 2006, p.159
  7. 1 2 Knight, 2011, pp.148
  8. 1 2 Knight, 2011, pp.148-149
  9. 1 2 3 4 5 6 7 Knight, 2011, p.149
  10. Knight 2011, p.139-142
  11. 1 2 3 Pommier, 2002, p.173
  12. Westrop, 2006, p.158-159
  13. 1 2 Sanger, 2002, p.52
  14. 1 2 Westrop, 2006, p.23

Bibliography