Optical module

Last updated

An optical module is a typically hot-pluggable optical transceiver used in high-bandwidth data communications applications. Optical modules typically have an electrical interface on the side that connects to the inside of the system and an optical interface on the side that connects to the outside world through a fiber optic cable. The form factor and electrical interface are often specified by an interested group using a multi-source agreement (MSA). Optical modules can either plug into a front panel socket or an on-board socket. Sometimes the optical module is replaced by an electrical interface module that implements either an active or passive electrical connection to the outside world. A large industry supports the manufacturing and use of optical modules.

Contents

Electrical Interface Types

There have been multiple variants of the electrical interface of optical modules that have been used over the years.

Analog direct

The earliest forms of optical modules had an analog NRZ electrical interface. In the transmit direction, the optical module would directly drive the laser or LED with the analog signal coming from the front system card. In the receive direction, the module would directly drive the receive electrical interface with the output of the analog optical-to-electrical receiver circuit.

Digital (retimed)

As speeds increased, the electrical interface was changed to a retimed digital interface. The Common Electrical Interface (CEI), [1] defined by the Optical Internetworking Forum (OIF) served as the central defining document for these interfaces. The IEEE 802.3 Ethernet working group has also been influential in the definition of the module interface.

Digital (unretimed)

In order to save power within the module, optical modules have been made that used the digital interface definition, such as the CEI, but without retiming the signals within the module. These modules delivered an analog connection between the two ends.

Analog Coherent Optics (ACO)

The Optical Internetworking Forum in 2016 published the CFP2-ACO or CFP2 - Analog Coherent Optics Module Interoperability Agreement (IA). This IA supports a configuration where the digital signal processor (DSP) is on the main board and analog optical components are on the module. This IA is useful in the case when the DSP exceeds the module power envelope. [2] The ACO interface can be used in coherent optics applications when the link delivers a flexible amount of bandwidth to the system, for example when combined with FlexE. The initial ACO IA is for the CFP2 module. The typical optical modulation that are used include Dual Polarization Quadrature Phase Shift Keying (DP-QPSK) and QAM-16.

Digital Coherent Optics (DCO)

These modules put the DSP on the module and use a conventional retimed digital interface. These modules can use the same optical modulation techniques as the ACO interfaces do.

Optical modulation and multiplexing types

Many different forms of optical modulation and multiplexing have been employed in optical modules.

NRZ and PAM-4 direct modulation

The most common modulation technique historically has been on-off keying or NRZ. Pulse-amplitude modulation (PAM-4) has also been extensively used.

Coherent modulation

In the 2010s, coherent optical modulation has been used. Techniques include Dual Polarization Quadrature Phase Shift Keying (DP-QPSK) and QAM-16.

Tunable optical frequency

Tunable lasers are sometimes used to allow a module to support various forms of network-based optical switching such as needed in certain cases by an optical mesh networks or a Reconfigurable optical add-drop multiplexer (ROADM). In these, the transmit laser can be tuned to a different optical frequency/wavelength. Similarly, the receiver is able to receive different optical frequencies.

Lambda multiplexing

Different optical wavelengths, also referred to as lambdas, of light are multiplexed in some optical modules using wavelength-division multiplexing (WDM). Variants include Coarse WDM (CWDM), Dense WDM (DWDM).

In-module components

Optical modules have a series of components inside, some of which have received attention from standards development organizations.

In-module gearbox

In many cases, the baud rate of the optical interface does not equal the baud rate of the electrical interface. In these cases, a gearbox is used within the module to convert between the two rates. For example if the module supports 4 x 25 Gb/s electrical inputs and 2 wavelengths of 50 Gb/s optical interface, then a gearbox must convert between 25 and 50 GBaud.

In-module forward error correction

Particularly in the long-reach module market, in-module Forward Error Correction (FEC) has been included. This has been in both proprietary and standards-based forms.

In-module optical transceiver implementation agreements

The OIF has created interoperability agreements to create multi-vendor interoperability for a series of in-module components, particularly focused on coherent transmission. These have included

In-module tunable laser implementation agreements

The OIF has created interoperability agreements to create multi-vendor interoperability for the tunable lasers that are sometimes used in optical modules. These have included

Transmit Optical Sub-Assembly

The Transmit Optical Sub-Assembly or TOSA in the optical module converts electrical signals into optical signals for optical transmitters. [8]

Electrical cable equivalent

40Gb QSFP+ copper twinax cable 40Gb QSFP+ copper twinax cable.jpg
40Gb QSFP+ copper twinax cable

Sometimes the optical module is replaced by an electrical interface module that implements either an active or passive electrical connection to the outside world. This is used when the link is short, particularly when connecting to a top of rack switch.

Front panel optical module MSAs

Many Multi-source agreements (MSAs) have come and gone over the years in the optical module industry.

SFP and QSFP family front-panel modules

SFP board 2 SFP board 2.jpg
SFP board 2

The Small form-factor pluggable transceiver (SFP) MSA has specified many optical module form factors over the years.

QSFP-40G-SR4 Transceiver QSFP-40G-SR4 Transceiver.jpg
QSFP-40G-SR4 Transceiver
Mpo-connector QSFP Mpo-connector QSFP.jpg
Mpo-connector QSFP

CFP family front-panel modules

The C form-factor pluggable (CFP) is an MSA among competing manufacturers for a common form-factor for the transmission of high-speed digital signals. The letter "C" in the name stands for the Latin letter C used to express the number 100 (centum), since the standard was primarily developed for 100 Gigabit Ethernet systems. [11]

The original CFP specification was proposed at a time when 10 Gbit/s signals were far more achievable than 25 Gbit/s signals. As such to achieve 100 Gbit/s line rate, the most affordable solution was based on 10 lanes of 10 Gbit/s. However, as expected, improvements in technology have allowed higher performance and higher density. Hence the development of the CFP2 and CFP4 specifications. While electrically similar, they specify a form-factor of 1/2 and 1/4 respectively in size of the original specification. Note that CFP, CFP2 and CFP4 modules are not interchangeable (but are inter-operable at the optical interface with appropriate connectors).

XENPAK, XPAK and X2 front panel modules

The XENPAK MSA was publicly announced on March 12, 2001 and the first revision of the document was publicly released on May 7, 2001 and was a multisource agreement (MSA), instigated by Agilent Technologies and Agere Systems, that defines a fiber-optic or wired transceiver module which conforms to the 10 Gigabit Ethernet (10GbE) standard of the Institute of Electrical and Electronics Engineers (IEEE) 802.3 working group. XENPAK has been replaced by more compact devices providing the same functionality. The most recent revision of the MSA, Issue 3.0, was published on September 18, 2002. The result covered all physical media dependent (PMD) types defined by the IEEE at that time for 802.3ae 10GbE. [12] Soon after the standard was introduced in 2001, two related standards emerged: XPAK and the X2. These two standards had the same electrical interface as XENPAK (known as XAUI) but different mechanical properties.

XFP family of front panel modules

Intel XFP Transceiver (MultiMode Fiber Optics) Intel XFP.jpg
Intel XFP Transceiver (MultiMode Fiber Optics)

The XFP (10 Gigabit Small Form Factor Pluggable) is a standard for transceivers for high-speed computer network and telecommunication links that use optical fiber. It was defined by an industry group in 2002, along with its interface to other electrical components, which is called XFI. XFP is a slightly larger form factor than the popular small form-factor pluggable transceiver, SFP and SFP+ .

OIF Multisource Agreement for 100G Long-Haul DWDM Transmission Module

The Optical Internetworking Forum defined a module for long-haul optics. Most of the other optical MSAs are focused on the data center market.

Other front-panel modules

On-Board Optical module MSAs

A recent trend has been to put pluggable modules on top of the printed circuit board instead of on the front panel. Two MSAs are working on implementation agreements for this market.

COBO family on-board modules

The Coalition for On-Board Optics (COBO) was established in 2014 to provide a home for the standardization of optical interfaces that were located on the middle of boards rather than on the front panel. [14]

CFP family on-board modules

Users of Optical Modules

Supermicro AOC-UIBQ-M2 dual port InfiniBand HCA Supermicro AOC-UIBQ-M2 dual port InfiniBand HCA.jpg
Supermicro AOC-UIBQ-M2 dual port InfiniBand HCA
Fibre Channel Media and Modules Fibre Channel Media and Modules.png
Fibre Channel Media and Modules

Multiple standards have used optical modules. Some of these more prominent standards are discussed below.

Infiniband

InfiniBand (abbreviated IB) is a computer-networking communications standard used in high-performance computing that features very high throughput and very low latency. It is used for data interconnect both among and within computers. InfiniBand is also utilized as either a direct, or switched interconnect between servers and storage systems, as well as an interconnect between storage systems. Infiniband uses optical modules extensively. [15]

Fiber Channel

Fibre Channel (FC) is a high-speed network technology (commonly running at 1, 2, 4, 8, 16, 32, and 128 gigabit per second rates) primarily used to connect computer data storage to servers. Fibre Channel is mainly used in storage area networks (SAN) in commercial data centers. Fibre Channel networks form a switched fabric because they operate in unison as one big switch. Fibre Channel typically runs on optical fiber cables within and between data centers. Fibre Channel uses optical modules extensively. [16]

Ethernet

Ethernet is a family of computer networking technologies commonly used in local area networks (LAN), metropolitan area networks (MAN) and wide area networks (WAN). Ethernet uses optical modules extensively in its higher rate interfaces. Representative interfaces that are commonly implemented in optical modules include 100GBASE-SR4, 100GBASE-LR4 and 100GBASE-ER4.

Optical module focused trade shows

OFC Logo blue July 2014 OFC Logo blue July 2014.svg
OFC Logo blue July 2014

The main trade show for the large optical module industry is the Optical Fiber Conference (OFC), that is held annually in southern California. Other prominent shows for the industry include ECOC in Europe and FOE in Japan.

See also

Related Research Articles

<span class="mw-page-title-main">Fast Ethernet</span> Ethernet standards that carry data at the nominal rate of 100 Mbit/s

In computer networking, Fast Ethernet physical layers carry traffic at the nominal rate of 100 Mbit/s. The prior Ethernet speed was 10 Mbit/s. Of the Fast Ethernet physical layers, 100BASE-TX is by far the most common.

<span class="mw-page-title-main">Gigabit Ethernet</span> Standard for Ethernet networking at a data rate of 1 gigabit per second

In computer networking, Gigabit Ethernet is the term applied to transmitting Ethernet frames at a rate of a gigabit per second. The most popular variant, 1000BASE-T, is defined by the IEEE 802.3ab standard. It came into use in 1999, and has replaced Fast Ethernet in wired local networks due to its considerable speed improvement over Fast Ethernet, as well as its use of cables and equipment that are widely available, economical, and similar to previous standards. The first standard for faster 10 Gigabit Ethernet was approved in 2002.

<span class="mw-page-title-main">Wavelength-division multiplexing</span> Fiber-optic communications technology

In fiber-optic communications, wavelength-division multiplexing (WDM) is a technology which multiplexes a number of optical carrier signals onto a single optical fiber by using different wavelengths of laser light. This technique enables bidirectional communications over a single strand of fiber, also called wavelength-division duplexing, as well as multiplication of capacity.

Fibre Channel (FC) is a high-speed data transfer protocol providing in-order, lossless delivery of raw block data. Fibre Channel is primarily used to connect computer data storage to servers in storage area networks (SAN) in commercial data centers.

<span class="mw-page-title-main">Gigabit interface converter</span>

A gigabit interface converter (GBIC) is a standard for transceivers, first defined in 1995 and commonly used with Gigabit Ethernet and Fibre Channel for some time. By offering a standard, hot swappable electrical interface, a single gigabit port can support a wide range of physical media, from copper to long-wave single-mode optical fiber, at lengths of hundreds of kilometers.

XENPAK is a multisource agreement (MSA), instigated by Agilent Technologies and Agere Systems, that defines a fiber-optic or wired transceiver module which conforms to the 10 Gigabit Ethernet (10GbE) standard of the Institute of Electrical and Electronics Engineers (IEEE) 802.3 working group. The MSA group received input from both transceiver and equipment manufacturers during the definition process. XENPAK has been replaced by more compact devices providing the same functionality.

<span class="mw-page-title-main">Small Form-factor Pluggable</span> Modular communications interface

Small Form-factor Pluggable (SFP) is a compact, hot-pluggable network interface module format used for both telecommunication and data communications applications. An SFP interface on networking hardware is a modular slot for a media-specific transceiver, such as for a fiber-optic cable or a copper cable. The advantage of using SFPs compared to fixed interfaces is that individual ports can be equipped with different types of transceivers as required.

The Optical Internetworking Forum (OIF) is a prominent non-profit consortium that was founded in 1998. It promotes the development and deployment of interoperable computer networking products and services through implementation agreements (IAs) for optical networking products and component technologies including SerDes devices.

<span class="mw-page-title-main">Multi-mode optical fiber</span> Type of optical fiber mostly used for communication over short distances

Multi-mode optical fiber is a type of optical fiber mostly used for communication over short distances, such as within a building or on a campus. Multi-mode links can be used for data rates up to 100 Gbit/s. Multi-mode fiber has a fairly large core diameter that enables multiple light modes to be propagated and limits the maximum length of a transmission link because of modal dispersion. The standard G.651.1 defines the most widely used forms of multi-mode optical fiber.

40 Gigabit Ethernet (40GbE) and 100 Gigabit Ethernet (100GbE) are groups of computer networking technologies for transmitting Ethernet frames at rates of 40 and 100 gigabits per second (Gbit/s), respectively. These technologies offer significantly higher speeds than 10 Gigabit Ethernet. The technology was first defined by the IEEE 802.3ba-2010 standard and later by the 802.3bg-2011, 802.3bj-2014, 802.3bm-2015, and 802.3cd-2018 standards. The first succeeding Terabit Ethernet specifications were approved in 2017.

The current portfolio of PowerConnect switches are now being offered as part of the Dell Networking brand: information on this page is an overview of all current and past PowerConnect switches as per August 2013, but any updates on current portfolio will be detailed on the Dell Networking page.

<span class="mw-page-title-main">10 Gigabit Ethernet</span> Standards for Ethernet at ten times the speed of Gigabit Ethernet

10 Gigabit Ethernet is a group of computer networking technologies for transmitting Ethernet frames at a rate of 10 gigabits per second. It was first defined by the IEEE 802.3ae-2002 standard. Unlike previous Ethernet standards, 10GbE defines only full-duplex point-to-point links which are generally connected by network switches; shared-medium CSMA/CD operation has not been carried over from the previous generations of Ethernet standards so half-duplex operation and repeater hubs do not exist in 10GbE. The first standard for faster 100 Gigabit Ethernet links was approved in 2010.

The C form-factor pluggable is a multi-source agreement to produce a common form-factor for the transmission of high-speed digital signals. The c stands for the Latin letter C used to express the number 100 (centum), since the standard was primarily developed for 100 Gigabit Ethernet systems.

Terabit Ethernet or TbE is Ethernet with speeds above 100 Gigabit Ethernet. 400 Gigabit Ethernet and 200 Gigabit Ethernet standards developed by the IEEE P802.3bs Task Force using broadly similar technology to 100 Gigabit Ethernet were approved on December 6, 2017. In 2016, several networking equipment suppliers were already offering proprietary solutions for 200G and 400G.

The XFP is a standard for transceivers for high-speed computer network and telecommunication links that use optical fiber. It was defined by an industry group in 2002, along with its interface to other electrical components, which is called XFI.

Dell Networking is the new name for the networking portfolio of Dell. In the first half of 2013, Dell started to rebrand their different existing networking product brands to Dell Networking. Dell Networking is the new name for the networking equipment that was known as Dell PowerConnect, as well as the Force10 portfolio.

in the telecommunications industry, a multi-source agreement (MSA) is an agreement among multiple manufacturers to make products which are compatible across vendors, acting as de facto standards, establishing a competitive market for interoperable products.

25 Gigabit Ethernet and 50 Gigabit Ethernet are standards for Ethernet connectivity in a datacenter environment, developed by IEEE 802.3 task forces 802.3by and 802.3cd and are available from multiple vendors.

The Common Electrical I/O (CEI) refers to a series of influential Interoperability Agreements (IAs) that have been published by the Optical Internetworking Forum (OIF). CEI defines the electrical and jitter requirements for 3.125, 6, 11, 25-28, and 56 Gbit/s electrical interfaces.

Coherent optical module refers to a typically hot-pluggable coherent optical transceiver that uses coherent modulation (BPSK/QPSK/QAM) rather than amplitude modulation (RZ/NRZ/PAM4) and is typically used in high-bandwidth data communications applications. Optical modules typically have an electrical interface on the side that connects to the inside of the system and an optical interface on the side that connects to the outside world through a fiber optic cable. The technical details of coherent optical modules were proprietary for many years, but have recently attracted efforts by multi-source agreement (MSA) groups and a standards development organizations such as the Optical Internetworking Forum. Coherent optical modules can either plug into a front panel socket or an on-board socket. Coherent optical modules form a smaller piece of a much larger optical module industry.

References

  1. "Common Electrical I/O (CEI) - Electrical and Jitter Interoperability agreements for 6G+ bps, 11G+ bps and 25G+ bps I/O" (PDF). OIF. 8 Feb 2014. Archived from the original (PDF) on 7 November 2017. Retrieved 20 July 2017.
  2. "OIF-CFP2-ACO-01.0" (PDF). 2016-01-22. Archived from the original (PDF) on 2017-12-15. Retrieved 2017-05-08.
  3. "Implementation Agreement for High Bandwidth Integrated Polarization Multiplexed Quadrature Modulators" (PDF). 2017-01-19. Retrieved 2017-07-20.
  4. "Implementation Agreement for Integrated Polarization Multiplexed Quadrature Modulated Transmitters" (PDF). 2015-05-15. Archived from the original (PDF) on 2016-10-20. Retrieved 2017-07-20.
  5. "Implementation Agreement for Integrated Dual Polarization Micro-Intradyne Coherent Receivers" (PDF). 2015-03-31. Archived from the original (PDF) on 2017-10-31. Retrieved 2017-07-20.
  6. "Integrable Tunable Laser Assembly MultiSource Agreement" (PDF). 2015-07-13. Archived from the original (PDF) on 2017-11-07. Retrieved 2017-07-21.
  7. "IMicro Integrable Tunable Laser Assembly Implementation Agreement 2015-07-13" (PDF). Archived from the original (PDF) on 2016-08-04. Retrieved 2017-07-21.
  8. "The Internal Components and Structure of The Optical Transceiver". Moore. Retrieved April 24, 2022.
  9. SFF Committee. "QSFP Public Specification" (PDF). SFF Committee. p. 12. Retrieved 22 June 2016.
  10. SFF Committee. "QSFP+ 28 Gb/s 4X Pluggable Transceiver Solution" (PDF). p. 5. Retrieved 22 June 2016.
  11. "CFP MSA".
  12. "Welcome to Welcome to XENPAK.org". Archived from the original on December 18, 2008. Retrieved May 7, 2011.
  13. "Cisco CPAK 100GBASE Modules Data Sheet".
  14. "Coalition for On-Board Optics". 2017-07-20. Retrieved 2017-07-20.
  15. "HIGH DENSITY EMBEDDED STORAGE | SFA14K| DDN".
  16. Preston, W. Curtis (2002). "Fibre Channel Architecture". Using SANs and NAS. Sebastopol, CA: O'Reilly Media. pp. 19–39. ISBN   978-0-596-00153-7. OCLC   472853124.