| T.4 Falcon 3 | |
|---|---|
 | |
| Role | Primary Training Glider |
| National origin | United Kingdom |
| Manufacturer | Slingsby Sailplanes |
| Designer | Fred Slingsby |
| First flight | 1935 |
| Number built | 9 |
| Developed from | Slingsby Falcon 2 |
The Slingsby T.4 Falcon 3 was a two-seat training glider produced from 1935, by Fred Slingsby in Kirbymoorside, Yorkshire.
Espin Hardwick persuaded Fred Slingsby to build a two-seat version of the Falcon. Slingsby enlarged the fuselage to accept side by side seating for pupil and instructor, and enlarged the aircraft to cope with the increased weight. The increased span wings were attached to a rectangular centre-section which was supported by six struts. To increase the field of vision the centre section had celluloid panels and the wing root fairing strips were made from a clear plastic, both of these vision aids tended to have short lives, and were usually replaced with doped fabric or plywood as appropriate.
After successful flight tests with only minor modifications, the Falcon 3 was put into production. Eight more were built, but didn't see as much use as trainers as they should have, due to the short-sighted prevailing opinion that trainee pilots gained more from having to master gliders with poor flying characteristics. Production halted by 1938 and most of the Falcon 3's were impressed for use by the Air Training Corps
UK
General characteristics
Performance
Aircraft of comparable role, configuration and era
Related lists
The Slingsby T.38 Grasshopper is a British primary training glider built by Slingsby Sailplanes for the Royal Air Force.
The Schneider Grunau Baby was a single-seat sailplane first built in Germany in 1931, with some 6,000 examples constructed in some 20 countries. It was relatively easy to build from plans, it flew well, and the aircraft was strong enough to handle mild aerobatics and the occasional hard landing. When the Baby first appeared, it was accepted wisdom that the pilot should feel as much unimpeded airflow as possible, to better sense rising and falling currents of air and temperature changes etc.
The HP-14 is a Richard Schreder-designed all-metal glider aircraft that was offered as a kit for homebuilding during the 1960s and 1970s. It was originally developed by retrofitting improved wings to the fuselage and tail of the HP-13. Schreder won the 1966 US national soaring championship in the prototype HP-14.
The Slingsby T.7 Kirby Cadet is a British training glider designed and built by Slingsby that first flew in 1935 and saw service with the Royal Air Force for use by the Air Training Corps as the Cadet TX.1 throughout the 1950, 1960s and 1970s.
The T.31 Tandem Tutor is a British military training glider, designed and built by Slingsby and used in large numbers by the Air Training Corps between 1951 and 1986.
The Slingsby T.21 is an open-cockpit, side-by-side two-seat glider, built by Slingsby Sailplanes Ltd and first flown in 1944. It was widely used by the RAF, Sri Lanka Air Force and by civilian gliding clubs.
The Slingsby Type 61 Falke was a licence-built version of the Scheibe SF 25B Motor glider built by Slingsby Sailplanes. It entered service with the Royal Air Force for air cadet training as the Slingsby Venture.
The Slingsby T.20 was a British glider designed and built by Slingsby that first flew in 1944.
The Slingsby Type 42 Eagle was a two-seat glider designed in England from 1952.
The Slingsby T.37 Skylark 1 was a small low-cost sailplane built during 1952-3 at Kirbymoorside, Yorkshire by Slingsby Sailplanes.
The Slingsby T.49 Capstan is a British two-seat glider of the 1960s built by Slingsby Sailplanes as a replacement for their earlier Type 42 Eagle. It is a high-winged monoplane of wooden construction, the last two-seat wooden glider built by Slingsby, intended for both training and general club flying. Side-by-side seats for the two pilots are accommodated in an enclosed cockpit with a one-piece perspex canopy. The prototype T.49A first flew in 1961, and it entered production as the T.49B in 1963. Thirty-four Capstans were built, one of which was fitted with an auxiliary engine with the designation T.49C Powered Capstan.
The Slingsby T.3 Primary was a single-seat training glider produced in the 1930s by Fred Slingsby in Kirbymoorside, Yorkshire.
The Slingsby T.6/T.23 Kirby Kite was a single-seat sport glider produced from 1935, by Fred Slingsby in Kirbymoorside, Yorkshire.
The Slingsby T.29 Motor Tutor was a single-seat motor glider produced from 1948, by Slingsby Sailplanes in Kirbymoorside, Yorkshire.
The Slingsby T.8 Kirby Tutor was a single-seat sport glider produced from 1937, by Fred Slingsby in Kirbymoorside, Yorkshire.
The Slingsby T.12 Gull was a British single-seat glider designed and built by Slingsby Sailplanes and first flown in 1938.
The Slingsby T.1/T.2 Falcon or British Falcon) was a single-seat sport glider produced, in 1931-37, by Fred Slingsby in Scarborough, Yorkshire.
The Slingsby T.53 was the first all-metal sailplane designed and built in the United Kingdom. It was designed and built by Slingsby Sailplanes for evaluation by the Royal Air Force.
The Slingsby T.24 Falcon 4 was a two-seat training glider designed in the UK just after World War II for ATC use. It was judged too expensive for production and only three were completed.
The RRG Falke of 1930 was a secondary training glider designed by Alexander Lippisch in Germany and intended to provide better performance than his earlier RRG Prüfling whilst being easier to fly because of its inherent stability. It was sold as plans for both club and commercial production and was built in Germany and abroad.
 | Wikimedia Commons has media related to Slingsby Falcon III . |