Solar-powered pump

Last updated

A windpump replaced by a solar-powered pump at a water hole in the Augrabies Falls National Park. Augrabies-windpump-001.jpg
A windpump replaced by a solar-powered pump at a water hole in the Augrabies Falls National Park.
This solar water pump up to 3.7 kW is useful for farmers. Solar water pump.jpg
This solar water pump up to 3.7 kW is useful for farmers.

Solar-powered pumps run on electricity generated by photovoltaic (PV) panels or the radiated thermal energy available from collected sunlight as opposed to grid electricity- or diesel-run water pumps. [1] Generally, solar-powered pumps consist of a solar panel array, solar charge controller, DC water pump, fuse box/breakers, electrical wiring, and a water storage tank. [2] The operation of solar-powered pumps is more economical mainly due to the lower operation and maintenance costs and has less environmental impact than pumps powered by an internal combustion engine. Solar pumps are useful where grid electricity is unavailable or impractical, and alternative sources (in particular wind) do not provide sufficient energy.

Contents

Components

A PV solar-powered pump system has three main parts - one or more solar panels, a controller, and a pump. The solar panels make up most (up to 80%) of the system's cost. [ citation needed ] The size of the PV system is directly dependent on the size of the pump, the amount of water that is required, and the solar irradiance available.

The purpose of the controller is twofold. Firstly, it matches the output power that the pump receives with the input power available from the solar panels. Secondly, a controller usually provides a low- or high-voltage protection, whereby the system is switched off, if the voltage is too low or too high for the operating voltage range of the pump. This increases the service life of the pump, thus reducing the need for maintenance. Other ancillary functions include automatically shutting down the system when the water source level is low or when the storage tank is full, regulating water output pressure, blending power input between the solar panels and an alternate power source such as the grid or an engine-powered generator, and remotely monitoring and managing the system through an online portal offered as a cloud service by the manufacturer.

Voltage of the solar pump motors can be alternating current (AC) or direct current (DC). DC motors are used for small to medium applications up to about 4 kW rating, and are suitable for applications such as garden fountains, landscaping, drinking water for livestock, or small irrigation projects. Since DC systems tend to have overall higher efficiency levels than AC pumps of a similar size, the costs are reduced, as smaller solar panels can be used.

Finally, if an AC solar pump is used, an inverter is necessary to change the DC power from the solar panels into AC for the pump. The supported power range of inverters extends from 0.15 to 55 kW, and can be used for larger irrigation systems. The panel and inverters must be sized accordingly, though, to accommodate the inrush characteristic of an AC motor. To aid in proper sizing, leading manufacturers provide proprietary sizing software tested by third-party certifying companies. The sizing software may include the projected monthly water output, which varies due to seasonal change in insolation.

Water pumping

Solar-powered water pumps can deliver drinking water, water for livestock, or irrigation water. [1] Solar water pumps may be especially useful in small-scale or community-based irrigation, as large-scale irrigation requires large volumes of water that in turn require a large solar PV array. [3] As the water may only be required during some parts of the year, a large PV array would provide excess energy that is not necessarily required, thus making the system inefficient, unless an alternative use can be found.

Solar PV water pumping systems are used for irrigation and drinking water in India. Most of the pumps are fitted with a 2.0 - 3.7 kW motor that receives energy from a 4.8 kWp PV array. The 3.7 kW systems can deliver about 124,000 liters of water/day from a total of 50 meters setoff head and 70 meters dynamic head. By 30 August 2016, a total of 120,000 solar PV water pumping systems had been installed around the world. [4] Energy storage in the form of water storage is better than energy storage in the form of batteries for solar water pumps because no intermediary transformation of one form of energy to another is needed. The most common pump mechanics used are centrifugal pumps, multistage pumps, borehole pumps, and helical pumps. Important scientific concepts of fluid dynamics such as pressure vs. head, pump heads, pump curves, system curves, and net suction head are really important for the successful deployment and design of solar-powered pumps. [5] [6] [7] [8] [9] [10]

Oil and gas

To combat negative publicity related to the environmental impacts of fossil fuels, including fracking, the oil and gas industry is embracing solar-powered pumping systems. [11] Many oil and gas wells require the accurate injection (metering) of various chemicals under pressure to sustain their operation and to improve extraction rates. Historically, these chemical injection pumps (CIPs) have been driven by gas reciprocating motors using the pressure of the well's gas, and exhausting the raw gas into the atmosphere. Solar-powered electrical pumps (solar CIPs) can reduce these greenhouse gas emissions. Solar arrays (PV cells) not only provide a sustainable power source for the CIPs, but can also provide an electricity source to run remote SCADA-type diagnostics with remote control and satellite/cell communications from very remote locations to a desktop or notebook monitoring computer.

Stirling engine

Instead of generating electricity to turn a motor, sunlight can be concentrated on the heat exchanger of a Stirling engine and used to drive a pump mechanically. This dispenses with the cost of solar panels and electric equipment. In some cases, the Stirling engine may be suitable for local fabrication, eliminating the difficulty of importing equipment. One form of Stirling engine is the fluidyne engine, which operates directly on the pumped fluid as a piston. Fluidyne solar pumps have been studied since 1987. [12] At least one manufacturer has conducted tests with a Stirling solar-powered pump. [13]

See also

Notes

  1. Note that the pumpshaft has been removed from the windpump and it is no longer connected to the borehole; instead, the borehole now contains an electric pump powered by the solar panels.

Related Research Articles

<span class="mw-page-title-main">Solar energy</span> Radiant light and heat from the Sun, harnessed with technology

Solar energy is radiant light and heat from the Sun that is harnessed using a range of technologies such as solar power to generate electricity, solar thermal energy, and solar architecture. It is an essential source of renewable energy, and its technologies are broadly characterized as either passive solar or active solar depending on how they capture and distribute solar energy or convert it into solar power. Active solar techniques include the use of photovoltaic systems, concentrated solar power, and solar water heating to harness the energy. Passive solar techniques include orienting a building to the Sun, selecting materials with favorable thermal mass or light-dispersing properties, and designing spaces that naturally circulate air.

<span class="mw-page-title-main">Power station</span> Facility generating electric power

A power station, also referred to as a power plant and sometimes generating station or generating plant, is an industrial facility for the generation of electric power. Power stations are generally connected to an electrical grid.

<span class="mw-page-title-main">Distributed generation</span> Decentralised electricity generation

Distributed generation, also distributed energy, on-site generation (OSG), or district/decentralized energy, is electrical generation and storage performed by a variety of small, grid-connected or distribution system-connected devices referred to as distributed energy resources (DER).

<span class="mw-page-title-main">Solar thermal energy</span> Technology using sunlight for heat

Solar thermal energy (STE) is a form of energy and a technology for harnessing solar energy to generate thermal energy for use in industry, and in the residential and commercial sectors. Solar thermal collectors are classified by the United States Energy Information Administration as low-, medium-, or high-temperature collectors. Low-temperature collectors are generally unglazed and used to heat swimming pools or to heat ventilation air. Medium-temperature collectors are also usually flat plates but are used for heating water or air for residential and commercial use.

<span class="mw-page-title-main">Solar water heating</span> Use of sunlight for water heating with a solar thermal collector

Solar water heating (SWH) is heating water by sunlight, using a solar thermal collector. A variety of configurations are available at varying cost to provide solutions in different climates and latitudes. SWHs are widely used for residential and some industrial applications.

Electrification is the process of powering by electricity and, in many contexts, the introduction of such power by changing over from an earlier power source.

<span class="mw-page-title-main">Solar inverter</span> Converts output of a photovoltaic panel into a utility frequency alternating current

A solar inverter or photovoltaic (PV) inverter is a type of power inverter which converts the variable direct current (DC) output of a photovoltaic solar panel into a utility frequency alternating current (AC) that can be fed into a commercial electrical grid or used by a local, off-grid electrical network. It is a critical balance of system (BOS)–component in a photovoltaic system, allowing the use of ordinary AC-powered equipment. Solar power inverters have special functions adapted for use with photovoltaic arrays, including maximum power point tracking and anti-islanding protection.

<span class="mw-page-title-main">Microgeneration</span> Small-scale heating and electric power creation

Microgeneration is the small-scale production of heat or electric power from a "low carbon source," as an alternative or supplement to traditional centralized grid-connected power.

<span class="mw-page-title-main">Solar panel</span> Assembly of photovoltaic cells used to generate electricity

A solar panel is a device that converts sunlight into electricity by using photovoltaic (PV) cells. PV cells are made of materials that produce excited electrons when exposed to light. The electrons flow through a circuit and produce direct current (DC) electricity, which can be used to power various devices or be stored in batteries. Solar panels are also known as solar cell panels, solar electric panels, or PV modules.

Solar air conditioning, or "solar-powered air conditioning", refers to any air conditioning (cooling) system that uses solar power.

<span class="mw-page-title-main">Stand-alone power system</span>

A stand-alone power system, also known as remote area power supply (RAPS), is an off-the-grid electricity system for locations that are not fitted with an electricity distribution system. Typical SAPS include one or more methods of electricity generation, energy storage, and regulation.

<span class="mw-page-title-main">Solar power in India</span>

India's solar power installed capacity was 81.813 GWAC as of 31 March 2024. India is the third largest producer of solar power globally.

<span class="mw-page-title-main">Charge controller</span> Battery current regulator

A charge controller, charge regulator or battery regulator limits the rate at which electric current is added to or drawn from electric batteries to protect against electrical overload, overcharging, and may protect against overvoltage. This prevents conditions that reduce battery performance or lifespan and may pose a safety risk. It may also prevent completely draining a battery, or perform controlled discharges, depending on the battery technology, to protect battery life. The terms "charge controller" or "charge regulator" may refer to either a stand-alone device, or to control circuitry integrated within a battery pack, battery-powered device, and/or battery charger.

<span class="mw-page-title-main">Solar power</span> Conversion of energy from sunlight into electricity

Solar power, also known as solar electricity, is the conversion of energy from sunlight into electricity, either directly using photovoltaics (PV) or indirectly using concentrated solar power. Solar panels use the photovoltaic effect to convert light into an electric current. Concentrated solar power systems use lenses or mirrors and solar tracking systems to focus a large area of sunlight to a hot spot, often to drive a steam turbine.

A photovoltaic system, also called a PV system or solar power system, is an electric power system designed to supply usable solar power by means of photovoltaics. It consists of an arrangement of several components, including solar panels to absorb and convert sunlight into electricity, a solar inverter to convert the output from direct to alternating current, as well as mounting, cabling, and other electrical accessories to set up a working system. Many utility-scale PV systems use tracking systems that follow the sun's daily path across the sky to generate more electricity than fixed-mounted systems.

<span class="mw-page-title-main">Photovoltaic thermal hybrid solar collector</span>

Photovoltaic thermal collectors, typically abbreviated as PVT collectors and also known as hybrid solar collectors, photovoltaic thermal solar collectors, PV/T collectors or solar cogeneration systems, are power generation technologies that convert solar radiation into usable thermal and electrical energy. PVT collectors combine photovoltaic solar cells, which convert sunlight into electricity, with a solar thermal collector, which transfers the otherwise unused waste heat from the PV module to a heat transfer fluid. By combining electricity and heat generation within the same component, these technologies can reach a higher overall efficiency than solar photovoltaic (PV) or solar thermal (T) alone.

A zero-carbon house or Net Zero Home is a house that does not emit greenhouse gasses (GHGs) into the atmosphere, either directly, or indirectly due to consumption electricity produced using fossil fuels. Most commonly zero-carbon housing is taken to mean zero emissions of carbon dioxide, which is the main climate pollutant from homes, although fugitive methane may also be emitted from natural gas pipes and appliances. Some homes may also emit refrigerant gasses eg CFCs from old equipment, which also cause climate change.

<span class="mw-page-title-main">Solar-powered Stirling engine</span> Technology used in concentrated solar power stations

A solar powered Stirling engine is a heat engine powered by a temperature gradient generated by the sun. Even though Stirling engines can run with a small temperature gradient, it is more efficient to use concentrated solar power.

The following outline is provided as an overview of and topical guide to solar energy:

<span class="mw-page-title-main">Copper in renewable energy</span> The use of copper in renewable energy

Renewable energy sources such as solar, wind, tidal, hydro, biomass, and geothermal have become significant sectors of the energy market. The rapid growth of these sources in the 21st century has been prompted by increasing costs of fossil fuels as well as their environmental impact issues that significantly lowered their use.

References

  1. 1 2 McDermott, James E. Horne; Maura (2001). The next green revolution : essential steps to a healthy, sustainable agriculture. New York [u.a.]: Food Products Press. p.  226. ISBN   1560228865.{{cite book}}: CS1 maint: multiple names: authors list (link)
  2. Romain (10 February 2021). "Solar Water Pumping (All you need to know)". Get Solar Savvy. Retrieved 10 February 2021.
  3. Simalenga, Mark Hankins ; illustrations by Francis Njeru & Michael Glen-Williamson ; layout by Michael Okendo ; edited by Timothy (1995). Solar electric systems for Africa : a guide for planning and installing solar electric systems in rural Africa (Rev. ed.). London: Commonwealth Science Council. p. 117. ISBN   0850924537.{{cite book}}: |first= has generic name (help)CS1 maint: multiple names: authors list (link)
  4. India's Solar Power GREENING INDIA'S FUTURE ENERGY DEMAND Archived 19 June 2008 at the Wayback Machine
  5. "Solar water pumps | ClimateTechWiki". www.climatetechwiki.org. Retrieved 4 May 2019.
  6. "Solar Water Pumping for Sustainable Water Supply". World Bank. Retrieved 4 May 2019.
  7. "Solar Water Pumping for Sustainable Water Supply".
  8. http://pubdocs.worldbank.org/en/540451475090902951/1-PVP-Literature-review-2015.pdf [ bare URL PDF ]
  9. http://documents.worldbank.org/curated/en/880931517231654485/pdf/123018-WP-P159391-PUBLIC.pdf [ bare URL PDF ]
  10. Solar Water Pumping Course Transcript. Strathmore Energy Research Center.
  11. Wethe, David (29 November 2012). "For Fracking, It's Getting Easier Being Green". Bloomberg Businessweek. Archived from the original on 3 December 2012. Retrieved 12 December 2012.
  12. C. D. West Stirling Engines and Irrigation Pumping, Oak Ridge National Laboratory, ORNL/TM-10475, August 1987
  13. http://www.bsrsolar.com/sv/produkte2_e.html retrieved 2013 April 9