| Spartan C3 | |
|---|---|
 | |
| Role | Open cockpit biplane |
| National origin | United States |
| Manufacturer | Spartan Aircraft Company |
| Designer | Willis C. Brown [1] |
| First flight | 25 October 1926 |
| Introduction | 1928 |
| Status | retired |
| Number built | approx 122 [2] |
| Developed into | Spartan NP |
The Spartan C3 is an American three-seat open-cockpit utility biplane from the late 1920s.
The C3s fuselage and wing struts were built up from welded chromium-molybdenum alloy steel tubes, faired with wood battens. [3] It had two open cockpits each protected from the wind with generously sized shatterproof-glass windscreens, and which could accommodated three people, with two in the front cockpit.
The wings on the prototype were built around spruce and plywood box beam spars that were replaced with solid spruce spars routed into I-beams on production examples. [3] Ribs were built up from spruce and plywood, while on the C3-225, duraluminium sheet covered the leading edge of the wing to improve the aerodynamic form. [4] The wings were braced with streamlined section steel wire. Both upper and lower wings used a Clark Y airfoil section, and had the same 32 ft (9.8 m) span and 60 in (1,500 mm) wing chord, with rounded wing tips. The wing was rigged without stagger, or washout and at a 0° angle of incidence. The upper wing was flat across, with no dihedral, while the lower wing had 2° of dihedral. Interconnected unbalanced ailerons were fitted to both wings inset from the wingtips. [4] The rudder and elevators were constructed similarly to the wings. [3]
Other than the metal panels around the nose, most of the airframe was covered in fabric that had been doped to tighten and seal it. [3]
The fuel tank was fitted into the upper wing center section in such a way that it could be removed without removing the wings. [3] On the C3-225, an additional removable fuel tank was added in the fuselage, and the wing tank acted as a header tank. [4]
The prototype had a conventional undercarriage similar to those used on most World War One aircraft, with a pair of vees braced from the lower longerons, connected with a spreader bar and suspension provided by bungee cords. This was replaced with a split-axle undercarriage on the C3-1 and C3-2, which had the legs braced to the opposite lower longerons. From the C3-3 onwards, each undercarriage leg was triangulated with two struts braced to a central keel in the bottom of the fuselage, and one oleo strut on each side to the upper longeron, providing a greater range of movement and reducing camber changes. [5] Early examples had a tail skid, while later ones had a tailwheel fitted.
The redesign of the undercarriage, and numerous other details changes coincided with Brown's visit to Europe to arrange for the use of the Siemens-Halske engine and had not been approved by him. He considered them unnecessary, and the fight over these changes led to his departure from the company. [5]
The keel used to brace the undercarriage on the C3-3 and later models coincided with a deepening of the fuselage, with additional fairing strips added, including to the underside of the fuselage. A headrest would also be added for the rear cockpit on later models.
The privately developed prototype to the C3 series first flew on 25 October 1926, originally powered with a stationary radial engine modified in the US from a 120 hp (89 kW) Le Rhône 9J rotary engine called a Super LeRhône. [6] [7] [8] The use of various engines was anticipated from the start, although the planned Hispano-Wright E-2 water-cooled V-8 engine was never used and only radial-engine powered versions were flown.
Despite the low-power engine, the type showed sufficient promise to warrant the formation of the Mid-Continent Aircraft Company in Tulsa, Oklahoma, to produce it, which would in turn be bought out and reorganized by prominent oilman William Skelly as the Spartan Aircraft Company in 1928. [7] [6]
The search for a suitable powerplant led to a number of different engines being installed. When production started, the Ryan-Siemens radial engine was chosen, but production of that engine stalled due to the worsening economic situation in Germany, where it was manufactured. [7] Even before the supply problems had manifested themselves, the next engine chosen, the Fairchild Caminez, had already been tried out, and was found to be extremely unreliable, so only one aircraft was fitted with it. The search for a reliable replacement for the Siemens led to the use of the more successful Walter NZ 120. [9]
The Axelson A, Comet 7-E, and Curtiss Challenger were also offered and installed in a few airframes, but none of them was successful for service use. While the Walter was fitted to a significant number of the earlier airframes, as an import, it was never a popular engine in the United States and eventually the Wright Whirlwind supplanted it. The ultimate variant was the C3-225, which was fitted with a much more powerful 225 hp (168 kW) Wright J-6-7 Whirlwind seven-cylinder radial engine, and it was given a larger fin and a greatly enlarged fuel tank in the wing center section. [4]
The C3 was used primarily by flight schools for flying training, including the Spartan School of Aeronautics. [10] Other firms used the aircraft's ability to carry two passengers for barnstorming flights, the type was popular for shuttling crews around the oil fields, while some were used as air taxis. [4] The Spartan was offered for sale for $6,750, which was later reduced to $5,975. [5]
A C3-2 fitted with a large fuel tank in the front cockpit demonstrated its reliability by being flown nonstop from Walkersville, Ontario, in Canada to Key West, Florida, a distance of (1,220 mi (1,960 km)) in 17.5 hours in November 1928. [11]
The financier behind the transformation of the Mid-Continent Aircraft company into Spartan, William Skelly, also purchased a number of C3s for the Skelly Oil Company's use.
The Fuerza Aerea Mexicana purchased four C3-120s in 1933 along with six of the later Spartan C2-175 monoplanes, [12] and 5 other examples were exported to Mexico for commercial and private use, [13] and at least one was operated by Aeronautica del Sur. [14]
A single C3-225 was exported to Argentina, [15] and both a C3-120 and a C3-225 went to Chile. [16]
Five C3s survive, four in the United States, and one in Germany as of 2020, of which at least three were airworthy.
(data from www.aerofiles.com)
Data from Juptner, 1964, pp.276-278
General characteristics
Performance
(Partial listing, only covers most numerous types)
The Pitcairn Mailwing family was a series of American mail carrier and three-seat sport utility biplane aircraft produced from 1927 to 1931.
The Consolidated Model 2 was a training airplane used by the United States Army Air Corps, under the designation PT-3 and the United States Navy under the designation NY-1.
The Cunningham-Hall Model PT-6 was an American six-seat cabin biplane aircraft of the late 1920s and was the first design of the Cunningham-Hall Aircraft Corporation of Rochester, New York.
The Buhl-Verville CA-3 Airster, was a utility aircraft built in the United States in 1926, notable as the first aircraft to receive a type certificate in the US, issued by the Aeronautics Branch of the Department of Commerce on March 29, 1927. It was a conventional single-bay biplane with equal-span unstaggered wings and accommodation for the pilot and passengers in tandem open cockpits. Marketed for a variety of roles including crop-dusting, aerial photography, and freight carriage, only a handful were built, some with water-cooled engines as the CW-3, and others with air-cooled engines as the CA-3. One CA-3 placed second in the 1926 Ford National Reliability Air Tour.
The Buhl AirSedan was a family of American civil cabin sesquiplane aircraft developed and manufactured by the Buhl Aircraft Company in the late 1920s. One example completed the first transcontinental non-stop roundtrip flight, made in 1929 by the CA-6 Spokane Sun-God, and the first Pope to have flown did so in a Buhl Airsedan.
The Travel Air 2000/3000/4000 (originally, the Model A, Model B and Model BH were open-cockpit biplane aircraft produced in the United States in the late 1920s by the Travel Air Manufacturing Company. During the period from 1924–1929, Travel Air produced more aircraft than any other American manufacturer, including over 1,000 biplanes. While an exact number is almost impossible to ascertain due to the number of conversions and rebuilds, some estimates for Travel Air as a whole range from 1,200 to nearly 2,000 aircraft.
The Curtiss Model 55 Kingbird was an airliner built in small numbers in the United States in the early 1930s. It was a twin-engine aircraft with a fuselage derived from the single-engine Curtiss Thrush. The Kingbird had two engine nacelles mounted on the struts on either side of the fuselage that braced the wing and the outrigger undercarriage. A distinctive design feature was the aircraft's blunt nose, located behind the propeller arcs. This allowed the engines to be mounted closer to each other and to the aircraft's centerline, therefore minimising asymmetrical thrust in case of an engine failure. For the same reason, the Thrush's single tailfin was replaced by twin tails on the Kingbird, and the main production model, the D-2 fitted a second horizontal stabilizer and elevator between these fins.
The Kreider-Reisner Challenger was an American utility biplane aircraft designed and produced by the Kreider-Reisner Aircraft Company, which was later taken over by the Fairchild Aircraft Company.
The Bullet Monoplane or Alexander Eaglerock Bullet was a low wing cabin monoplane that was a departure from traditional biplane aircraft of the era.
The Bach Air Yacht was a trimotor airliner produced in the United States in the 1920s. Typical of its day, it was a high-wing braced monoplane, with fixed tailwheel undercarriage. Unusual for airliners of the late 1920s, the Air Yachts were constructed almost entirely of wood with steel fittings, undercarriage, and struts. Different models were powered by varying combinations of Wright, Ryan-Siemens, Kinner, Comet, and Pratt & Whitney engines, a large engine in the nose of the aircraft, and two smaller "helpers" under the wings in nacelles supported by struts. As with so many aircraft companies of the late 1920s, the Bach Aircraft Company succumbed to the Great Depression, thus further development of the Air Yacht was abandoned after the 3-CT-9.
The Waco 10/GXE/Waco O series was a range of three-seat open-cockpit biplanes built by the Advance Aircraft Company, later the Waco Aircraft Company.
The Waco Standard Cabin series is a range of American single-engine 4–5 seat fabric covered cabin biplanes produced by the Waco Aircraft Company beginning in 1931 with the QDC and continuing until 1942 when production ended for the VKS-7F. They were used as light passenger and utility transports, navigational trainers, bushplanes and briefly as maritime reconnaissance aircraft during World War 2.
The Spartan C2 is a light aircraft produced in the United States in the early 1930s as a low-cost sport machine that would sell during the Great Depression.
The Curtiss/Curtiss-Robertson Model 56 Thrush was a 1929 six passenger high-wing fixed undercarriage single-engine cabin monoplane airliner and utility transport powered by either a Curtiss Challenger or a Wright Whirlwind radial engine and built as an enlargement of the earlier Curtiss Robin. Several were used for record breaking endurance flights by female pilots during the early 1930s including one in which the aircraft stayed aloft for almost ten days.
The Emsco B-4 Cirrus was a mid-wing, two-seat trainer built in the US in the late 1920s. Six were built and three variants with more powerful engines flown.
The Command-Aire 3C3 and similar 4C3 and 5C3 are American three-seat open cockpit utility, training and touring biplanes developed by Command-Aire in the late 1920s and early 1930s.
The Gee Bee Model A was an American two-seat open cockpit single-bay biplane developed by the Granville Brothers that first flew in 1929.
The Curtiss-Wright CW-14, named variously Travel Air, Sportsman, Speedwing and Osprey is an American 3-seat open cockpit single-bay biplane from the 1930s that was developed by Travel Air as a replacement for the highly successful Travel Air 4000. As a result of the Great Depression, which also limited sales, Travel Air merged into the Curtiss-Wright group of companies before production could start, so all examples were built by Curtiss-Wright. Its main claim to fame would be as the most numerous aircraft used in the Chaco war, where it formed the backbone of the Bolivian Air Force.
The Butler Blackhawk and the Skyway from which it was developed were American three-seat open-cockpit single engine biplanes of the late 1920s that were built in small numbers immediately prior to having their intended production run interrupted by the onset of the Great Depression.
The Wallace Touroplane was a late 1920s U.S. three seat, high wing cabin monoplane. About 20 were built.
