Vibrational analysis with scanning probe microscopy

Last updated

The technique of vibrational analysis with scanning probe microscopy allows probing vibrational properties of materials at the submicrometer scale, and even of individual molecules. [1] [2] [3] This is accomplished by integrating scanning probe microscopy (SPM) and vibrational spectroscopy (Raman scattering or/and Fourier transform infrared spectroscopy, FTIR). This combination allows for much higher spatial resolution than can be achieved with conventional Raman/FTIR instrumentation. The technique is also nondestructive, requires non-extensive sample preparation, and provides more contrast such as intensity contrast, polarization contrast and wavelength contrast, as well as providing specific chemical information and topography images simultaneously.

Contents

History

Raman-NSOM

Near-field scanning optical microscopy (NSOM) was described in 1984, [4] and used in many applications since then. [5] The combination of Raman scattering and NSOM techniques was first realized in 1995, when it was used for imaging a Rb-doped KTP crystal at a spatial resolution of 250 nm. [6]

NSOM employs two different methods for data collection and analysis: the fiber tip aperture approach and the apertureless metal tip approach. [1] NSOM with aperture probes has a smaller aperture that can increase the spatial resolution of NSOM; however, the transmission of light to the sample and the collection efficiency of the scattered/emitted light is also diminished. [7] The apertureless near-field scanning microscopy (ANSOM) was developed in the 1990s. ANSOM employs a metalized tip instead of an optical fiber probe. The performance of the ANSOM strongly depends on the electric field enhancement factor of the metalized tip. This technique is based on surface plasmon resonance (SPR) which is the precursor of tip-enhanced Raman scattering (TERS) and surface-enhanced Raman scattering (SERS).

In 1997, Martin and Girard demonstrated theoretically that electric field under a metallic or dielectric tip (belonging to NSOM apertureless technique) can be strongly enhanced if the incident field is along the tip axis. Since then a few groups have reported Raman or fluorescence enhancement in near field optical spectroscopy by apertureless microscopy. [8] In 2000, T. Kalkbrenner et al. used a single gold particle as a probe for apertureless scanning and presented images of an aluminium film with 3 μm holes on a glass substrate. [9] The resolution of this apertureless method was 100 nm, that is comparable to that of fiber-based systems [9] Recently, a carbon nanotube (CNT) having a conical end, tagged with gold nanoparticles, was applied as a nanometer-resolution optical probe tip for NSOM. [10] NSOM images were obtained with a spatial resolution of ~5 nm, demonstrating the potential of a composite CNT probe tip for nanoscale-resolution optical imaging.

Tip-enhanced Raman scattering

There are two options for realizing apertureless NSOM-Raman technique: TERS and SERS. TERS is frequently used for apertureless NSOM-Raman and can significantly enhance the spatial resolution. This technique requires a metal tip to enhance the signal of the sample. That is why an AFM metal tip is usually used for enhancing the electric field for molecule excitation. Raman spectroscopy was combined with AFM in 1999. [11] [12] A very narrow aperture of the tip was required to obtain a relatively high spatial resolution; such aperture reduced the signal and was difficult to prepare. In 2000, Stȍckle et al. [13] first designed a setup combining apertureless NSOM, Raman and AFM techniques, in which the tip had a 20 nm thick granular silver film on it. They reported a large gain in the Raman scattering intensity of a dye film (brilliant cresyl blue) deposited on a glass substrate if a metal-coated AFM tip was brought very close to the sample. About 2000-fold enhancement of Raman scattering and a spatial resolution of ~55 nm were achieved. [14]

Similarly, Nieman et al. [15] used an illuminated AFM tip coated with a 100 nm thick film of gold to enhance Raman scattering from polymers samples and achieved a resolution of 100 nm. In the early research of TERS, the most commonly used coating materials for the tip probe were silver and gold. [14] [15] High-resolution spatial maps of Raman signals were obtained with this technique from molecular films of such compounds as brilliant cresyl blue, malachite green isothiocyanate and rhodamine 6G, [16] as well as individual carbon nanotubes. [17]

IR-NSOM and AFM

IR near-field scanning optical microscopy (IR-NSOM) is a powerful spectroscopic tool because it allows subwavelength resolution in IR spectroscopy. Previously, IR-NSOM was realized by applying a solid immersion lens with a refractive index of n, which shortens wavelength (λ) to (λ/n), compared to FTIR-based IR microscopy. [18] In 2004, an IR-SNOM achieved a spatial resolution ~λ/7 that is less than 1 μm. [18] This resolution was further improved to about λ/60 that is 50–150 nm for a boron nitride thin film sample. [19]

IR-NSOM uses an AFM to detect the absorption response of a material to the modulated infrared radiation from an FTIR spectrometer and therefore is also referred to as AFM/FTIR spectroscopy. Two approaches have been used to measure the response of polymer systems to infrared absorption. The first mode relies on the AFM contact mode, and the second mode of operation employs a scanning thermal microscopy probe (invented in 1986 [20] ) to measure the polymer's temperature increase. In 2007, AFM was combined with infrared attenuated total reflection (IR-ATR) spectroscopy to study the dissolution process of urea in a cyclohexane/butanol solution with a high spatial resolution. [21]

Theory and instrumentation

Raman-NSOM

There are two modes for the operation of NSOM technique, [5] [22] with and without an aperture. These two mode have also been combined with the near-field Raman spectroscopy. [7] [23] [24] The near-field aperture must be nanosized that complicates the probe manufacturing process. [25] Also, the aperture method usually has a very weak signal due to weak excitation and Raman scattering signal. Overall, these factors lower the signal-to-noise ratio in aperature based NSOM/Raman technique. Apertureless probes are based on a metal-coated tip and provide a stronger signal. [26]

Aperture-based detection

Although the apertureless mode is more promising than the aperture mode, the latter is more widely used because of easier instrumental setup and operation. To obtain a high resolution Raman micrograph/spectrum, the following conditions should be met: (1) the size of the aperture must be on the order of the wavelength of the excitation light. (2) The distance from the tip of the probe to the sample must be smaller than excitation wavelength. (3) The instrument must remain stable over a long time. An important AFM feature is the ability to accurately control the distance between the sample and probe tip, which is the reason why the AFM-Raman combination is preferred for realizing Raman-NSOM.

Apertureless mode

The main drawback of the aperture mode is that the small aperture size reduces the signal intensity and is difficult to fabricate. Recently, researchers have focused on the apertureless mode, which utilizes SPR theory to produce stronger signals. There are two techniques supporting this mode: SERS and TERS.

TERS technique
animation for TERS KLSBAnimation.gif
animation for TERS

Theory and instrumentation of Raman/AFM and IR/AFM combine the theory of SPR (AFM and NSOM) and Raman scattering, and this combination is based on TERS. In TERS, the electric field of excitation source induces an SPR in the tip of the probe. If the electric field vector of the incidence light is perpendicular (s-polarized) to the metal tip axis, the free electrons are driven to the sides lateral of the tip. If it is parallel (p-polarized) to the tip axis, the free electrons on the surface of the metal are confined to the end of the apex of tip. As a consequence, there is a very large electric-field enhancement which is sensed by the molecules close to it leading to a stronger signal. [26]

A typical approach in a TERS experiment is to focus the laser beam on a metal tip with the light polarized along the tip axis, followed by collection of the surface-enhanced Raman scattered light from the sample in the enhancement zone of the tip using optics. [14]

Depending on the sample and experiment, different illumination geometries have been applied in TERS experiments, as shown in figure 4. With p-polarized (parallel to the surface normal) incidence light, the plasmon excitation at the tip is most efficient. If the focusing objective lens is also used for collecting the scattered photons (backscattering geometry), the optimum angle is around 55° with respect to the surface normal. This is because the scattering lobe is maximum with this configuration and it provides a much enhanced signal. [27] The setup of figure 4(A) is usually used for the large thick samples. Setup (B) handles semi-transparent or transparent samples, such as single cells, tissue samples and biopolymers. [14] The setup of figure 4(C) is preferred for opaque samples because all the light would be focused by the parabolic mirror.

KLSBFig 2.jpg
KLSBFig 3.jpg
KLSBFig 4.jpg
Figure 2. S- and p-polarization with laser excitation. [28] Figure 3. TERS setup using the back-excitation mode. [28] Figure 4. TERS setup: (A) side illumination (p polarized); (B) in-line illumination (objective, s-polarized); (C) in-line illumination (parabolic mirror). [28]
Comparison of TERS and SERS

Both TERS and SERS rely on a localized surface plasmon for increasing the ought-to-be weak Raman signal. [29] The only difference between them is that the sample in SERS has a rough surface that hinders application of a sharp AFM-like tip. TERS, on the other hand, uses a metal-coated tip having some roughness at nanoscale. [30] [31] The “hot spot” theory [32] is very popular in explaining the large enhancement in the signal. That is, the signal from “hot spots” on the surface of the sample dominates the total signal from the sample. [33] This is also reinforced by the fact that the distance between nanoparticles and sample is an important factor in obtaining high Raman signal.

Raman/AFM instrumentation

Figure 5. TERS system combining AFM and Raman scattering. KLSBFig 5.jpg
Figure 5. TERS system combining AFM and Raman scattering.

The Raman/AFM technique has two approaches: aperture and apertureless, and the apertureless mode is realized with SERS and TERS. Figure 5 is the example of an integrated TERS system. It shows that there are five main components for a whole integrated TERS (apertureless) system. These components are: microscope, one objective lens, one integrated AFM head, a Raman spectrometer and a CCD. The laser is focused on the sample, on piezo-stage and the AFM tip by the moving the laser beam along the tip. The movement of the laser beam is achieved by the mirror in the top left corner. The XYZ piezo-stage in the left bottom holds the sample. In this design, the laser beam is focused on the sample through an objective lens, and the scattered light is collected by the same lens.

This setup utilizes a low contact-pressure to reduce the damage to the AFM tip and sample. [21] The laser power is typically below 1 mW. [21] The notch filter can filter Rayleigh scattering from the excitation laser light from the back of the cantilever. The laser beam is focused on the apex of the gold-coated AFM tip and the sample. The laser scanning is completed by the moving the mirror across the approaching tip. A small enhance in background occurs when the laser spot focuses on the tip area. The movement of the XYZ piezo-stage finishes the sample scanning. The wide red signal is Raman signal which is collected through the objective lens. The same lens is also used for excitation of the sample and collecting the Raman signal.

NSOM/FTIR, AFM/FTIR and AFM-IR

Because of the diffraction limit in the resolution of conventional lens-based microscopes, namely D = 0.61λ/nsinθ, [34] the maximum resolution obtainable with an optical microscope is ~200 nm. A new type of lens using multiple scattering of light allowed to improve the resolution to about 100 nm. [35] Several new microscopy techniques with a sub-nanometer resolution have been developed in the last several decades, such as electron microscopy (SEM and TEM) and scanning probe microscopy (NSOM, STM and AFM). SPM differs from other techniques in that the excitation and signal collection are very close (less than diffraction limit distance) to the sample. Instead of using a conventional lens to obtain magnified images of samples, an SPM scans across the sample with a very sharp probe. Whereas SEM and TEM usually require vacuum and an extensive sample preparation, SPM measurements can be performed in atmospheric or liquid conditions.

Despite the achievable resolution of atomic scale for AFM and NSOM techniques, it does not provide chemical information of the sample. The infrared part of the electromagnetic spectrum covers molecular vibrations which can characterize chemical bonding within the sample. [36]

By combining SPM and vibrational spectroscopy, AFM/IR-NSOM and AFM-IR have emerged as useful characterization tools that integrate the high spatial resolution abilities of AFM with IR spectroscopy. [37] [38] [39] [40] [41] [42] [43] [44] [45] [46] This new technique can be referred to as AFM-FTIR, AFM-IR and NSOM/FTIR. AFM and NSOM can be used to detect the response when a modulated infrared radiation generated by an FTIR spectrometer is absorbed by a material. In the AFM-IR technique the absorption of the radiation by sample will cause a rapid thermal expansion wave which will be transferred to the vibrational modes of the AFM cantilever. Specifically, thermal expansion wave induces a vertical displacement of the ATM tip (Figure 6). [47] A local IR absorption spectrum then can be obtained through the measurement of the amplitude of the cantilever, which is a function of the IR source wavelength. For example, when the radiation laser wavelength is tuned at the resonance frequency with the vibrational absorption frequency of the sample, the displacement intensity of the cantilever will increase until the laser wavelength reaches the maximum of sample absorption. [47] The displacement of the cantilever will then be reduced as the laser wavelength is tuned past the absorption maximum. This approach can map chemical composition beyond the diffraction-limit resolution and can also provide three-dimensional topographic, thermal and mechanical information at the nanoscale. Overall, it overcomes the resolution limit of traditional IR spectroscopy and adds chemical and mechanical mapping to the AFM and NSOM.

Figure 6. Schematic diagram of surface deformation effects creating displacement of cantilever KLSBFig 6.jpg
Figure 6. Schematic diagram of surface deformation effects creating displacement of cantilever

Infrared light source

The ideal IR source should be monochromatic and tunable within a wide range of wavelength. According to T ∝d4/λ4, where T is the transmission coefficient, d the aperture diameter and λ is wavelength, the aperture-based NSOM/FTIR transmission is even more limited due to the long infrared wavelength; [48] [49] therefore, an intense IR source is needed to offset the low transmission through the optical fiber. The common bright IR light sources are the free-electron laser (FEL), [2] [39] [45] color-center lasers, CO2 lasers and laser diodes. FEL is an excellent IR source, with 2–20 μm spectral range, [50] [51] short pulses (picosecond) and high average power (0.1-1 W). Alternately, a tabletop picosecond optical parametric oscillator (OPO) can be used which is less expensive, but has a limited tunability and a lower power-output. [44] [52]

NSOM/FTIR experimental setup

The essence of NSOM/FTIR is that it allows the detection of non-propagating evanescent waves in the near-field (less than one wavelength from the sample), thus yielding high spatial resolution. Depending on the detection modes of these non-propagating evanescent waves, two NSOM/FTIR instrumentations are available: apertureless NSOM/FTIR and aperture-based NSOM/FTIR.

Aperture-based NSOM/FTIR

In aperture-based NSOM/FTIR, the probe is a waveguide with a tapered tip with a very small, sub-wavelength size aperture. When the aperture is brought into the near-field, it collects the non-propagating light and guides it to the detector. In general, there are two modes when the aperture is scanned over the sample: illumination mode and collection mode (Figure 7).

Figure 7. Schematic diagram of (1) collection mode and (2) illumination mode KLSBFig 7.jpg
Figure 7. Schematic diagram of (1) collection mode and (2) illumination mode

The high-quality infrared fiber tip is very important in realizing NSOM/FTIR technique. There are several types of fibers, such as sapphire, chalcogenide glass, fluoride glass and hollow silica guides. [53] Chalcogenide glasses are widely used because of their high transmittance in the broad IR range of 2–12 μm. [54] The fluoride fibers also exhibit low transmitting losses beyond 3.0 μm.

Apertureless NSOM/FTIR

The probe is a sharp metal tip ending with a single or a few atoms. The sample is illuminated from far-field and the radiation is focused at the contact area between probe and sample. When this tip approaches the sample, usually within 10 nm, the incident electromagnetic field is enhanced due to the resonant surface plasma excitation as well as due to hot-spots in the sharp tip. The dipole interaction between the tip and sample change the non-propagating waves into propagating waves by scattering, and a detector collects the signal in the far-field. An apertureless NSOM/FTIR usually has better resolution (~5–30 nm) compared with aperture-based NSOM/FTIR (~50–150 nm). One main challenge in apertureless NSOM/FTIR is a strong background signal because the scattering is obtained from both near-field and remote area of the probe. Thus, the small near-field contribution to the signal has to be extracted from the background. One solution is to use a very flat sample with only optical spatial fluctuation. [55] Another solution is to apply constant-height mode scanning or pseudo-constant-height mode scanning. [56]

Experimental scheme of aperture-based NSOM/FTIR

Figure 8 shows the experimental setup used in NSOM/FTIR in the external reflection mode. FEL source is focused on the sample from the far-field using a mirror. The distance between the probe and a sample is kept at a few nanometers during scanning.

Figure 8: General NSOM/FTIR setup. KLSBFig 8.jpg
Figure 8: General NSOM/FTIR setup.

Figure 9 is the cross-section of a NSOM/FTIR instrument. As shown below, sample is placed on a piezo-electric tube scanner, in which the x-y tube has four parts, namely x+, x-, y+ and y-. Lateral (x-y plane) oscillation of the fiber tip is induced by applying an AC voltage to a dither piezo-scanner. Also, the fiber tip is fixed to a bimorph piezo-scanner so that the amplitude of the oscillation of the tip can be monitored through the scanner.

Figure 9: Cross-section of NSOM/FTIR KLSBFig 9.jpg
Figure 9: Cross-section of NSOM/FTIR

AFM-IR setup

Spatial resolution

The spatial resolution of an AFM-IR instrument is related to the contact area between the probe and sample. [58] The contact area is given by a3 = 3PR/4E* and 1/E* = (1-n12)/ E1+ (1-n22)/ E2, where P is the force employed to the probe, n1 and n2 represent the Poisson ratios of the sample and probe, respectively, and E1 and E2 are the elastic moduli of the sample and probe materials respectively. [59] Typically, an AFM-IR has a lateral spatial resolution of 10–400 nm, [46] for example, 100 nm, [43] λ/150, [40] and λ/400. [41] Recently, Ruggeri et al. have demonstrated the acquisition of infrared absorption spectra and chemical maps at the single molecule level in the case of protein molecules with ca. 10 nm diameter and a molecular weight of 400 kDa.

Instrumentation

In AFM-IR, an AFM probe is used to measure the absorption response of the sample to infrared radiation. The general approach for AFM/FTIR is shown in Figure 10. [60]

Figure 10. General approach used for AFM-FTIR. The output from the probe resembles an interferogram and is Fourier-transformed to obtain the infrared absorption spectrum of the sample. KLSBFig 10.jpg
Figure 10. General approach used for AFM-FTIR. The output from the probe resembles an interferogram and is Fourier-transformed to obtain the infrared absorption spectrum of the sample.

There are a few different experimental setups when the infrared radiation is projected onto the sample as shown below: top, side, and bottom illumination setups (Figure 11). [3]

Figure 11. Illumination setups used in AFM/FTIR spectroscopy. KLSBFig 11.jpg
Figure 11. Illumination setups used in AFM/FTIR spectroscopy.

In the first developed setup of AFM-IR, a sample is mounted onto an infrared-transparent zinc selenide prism for excitation purposes (Figure 12), then an optical parametric oscillator (OPO)-based tunable IR lased is radiated on the molecules to be probed by the instrument. Similar to conventional ATR spectroscopy, IR beam illuminates the sample through total internal reflection mechanism (Figure 12). The sample will heat up while absorbing radiation which causes a rapid thermal expansion of the sample surface. [40] [44] This expansion will increase the resonant oscillations of the AFM cantilever in a characteristic ringdown pattern (ringdown patterns means the decay of cantilever oscillation exponential in nature [44] ). Through Fourier transformation analysis, the signal could be isolated to obtain the amplitudes and frequencies of the oscillations. The amplitudes of the cantilever provide information of local absorption spectra, whereas the oscillation frequencies depend on the mechanical stiffness of the sample (Figure 12). [43] [44]

Figure 12. The AFM-IR technique combines AFM with an IR spectrometer as shown in this schematic. KLSBFig 12.jpg
Figure 12. The AFM-IR technique combines AFM with an IR spectrometer as shown in this schematic.

Pros and cons

NSOM combined with FTIR/Raman techniques can provide local chemical information together with topographical details. This technique is non-destructive and can work in a variety of environments (liquids), for example, when detecting single biomolecules. [18] [59] [61] [62] The illuminated area of sample is relatively big at around 1 μm. However, the sampling area is only ~10 nm. This means that a strong background from an unclean tip contributes to the overall signal, hindering the signal analysis. [56]

The Raman spectroscopy in general could be time-consuming due to the low scattering efficiency (<1 in 107 photons). It usually takes several minutes to accumulate a conventional Raman spectrum, and this time could be much longer in Raman-NSOM; for example, 9 hours for a 32×32-pixel image. [6] [19] As to near-field IR/AFM, high optical losses in aqueous environments (water is strongly absorbing in the IR range) reduces the signal-to-noise ratio. [18] [63]

Applications

Improving the resolution and enhancing the instrumentation with user-friendly hardware and software will make AFM/NSOM coupled with IR/Raman a useful characterization tool in many areas including biomedical, materials and life sciences. [64] For example, this technique was used in detecting the spin-cast thin film of poly(dimethylsiloxane) with polystyrene on it by scanning the tip over the sample. The shape and size of polystyrene fragments was detected at a high spatial resolution due to its high absorption at specific resonance frequencies. [65] Other examples include inorganic boron nitride thin films characterization with IR-NSOM. [16] The images of single molecule rhodamine 6G (Rh-6G) was obtained with a spatial resolution of 50 nm. [66] These techniques can be also used in numerous biological related applications including the analysis of plant materials, bone, and single cells. Biological application was demonstrated by detecting details of conformation changes of cholesteryl-oleate caused by FEL irradiation with a spatial resolution below the diffraction limit. [67] Researchers also used Raman/NSOM in tracking the formation of energy-storing polymer polyhydroxybutyrate in bacteria Rhodobacter capsulatus. [68]

This characterization tool may also help in the kinetic studies on physical and chemical processes at a wide variety of surfaces giving chemical specificity via IR spectroscopy as well as high-resolution imaging via AFM. [18] For example, the study of the hydrogen termination of Si (100) surface was performed by studying the absorbance of Si-O bond to characterize the reaction between silicon surface and atmospheric oxygen. [69] Studies were also conducted where the reactivity of a polymer, a 1000-nm-thick poly-(tert-butylmethacrylate) (PTBMA) combined with a photochemically modified 500-nm-thick poly(methacrylic acid) (PMAA), with water vapor depicted the different absorption bands before and after water uptake by the polymer. Not only the increased swell of PMAA (280 nm) was observed but also the different absorption ability of water was shown by the different transmission of IR light at a much smaller dimension (<500 nm). These results are related to polymer, chemical and biological sensors, and tissue engineering and artificial organ studies. [70] Because of their high spatial resolution, NSOM/AFM-Raman/IR techniques can be used for measuring the width of multilayer films, including layers which are too small (in the x and y directions) to be probed with conventional IR or Raman spectroscopy. [39]

Related Research Articles

<span class="mw-page-title-main">Infrared spectroscopy</span> Measurement of infrared radiations interaction with matter

Infrared spectroscopy is the measurement of the interaction of infrared radiation with matter by absorption, emission, or reflection. It is used to study and identify chemical substances or functional groups in solid, liquid, or gaseous forms. It can be used to characterize new materials or identify and verify known and unknown samples. The method or technique of infrared spectroscopy is conducted with an instrument called an infrared spectrometer which produces an infrared spectrum. An IR spectrum can be visualized in a graph of infrared light absorbance on the vertical axis vs. frequency, wavenumber or wavelength on the horizontal axis. Typical units of wavenumber used in IR spectra are reciprocal centimeters, with the symbol cm−1. Units of IR wavelength are commonly given in micrometers, symbol μm, which are related to the wavenumber in a reciprocal way. A common laboratory instrument that uses this technique is a Fourier transform infrared (FTIR) spectrometer. Two-dimensional IR is also possible as discussed below.

<span class="mw-page-title-main">Microscopy</span> Viewing of objects which are too small to be seen with the naked eye

Microscopy is the technical field of using microscopes to view objects and areas of objects that cannot be seen with the naked eye. There are three well-known branches of microscopy: optical, electron, and scanning probe microscopy, along with the emerging field of X-ray microscopy.

Fourier-transform spectroscopy is a measurement technique whereby spectra are collected based on measurements of the coherence of a radiative source, using time-domain or space-domain measurements of the radiation, electromagnetic or not. It can be applied to a variety of types of spectroscopy including optical spectroscopy, infrared spectroscopy, nuclear magnetic resonance (NMR) and magnetic resonance spectroscopic imaging (MRSI), mass spectrometry and electron spin resonance spectroscopy.

<span class="mw-page-title-main">Raman spectroscopy</span> Spectroscopic technique

Raman spectroscopy is a spectroscopic technique typically used to determine vibrational modes of molecules, although rotational and other low-frequency modes of systems may also be observed. Raman spectroscopy is commonly used in chemistry to provide a structural fingerprint by which molecules can be identified.

<span class="mw-page-title-main">Optical microscope</span> Microscope that uses visible light

The optical microscope, also referred to as a light microscope, is a type of microscope that commonly uses visible light and a system of lenses to generate magnified images of small objects. Optical microscopes are the oldest design of microscope and were possibly invented in their present compound form in the 17th century. Basic optical microscopes can be very simple, although many complex designs aim to improve resolution and sample contrast.

<span class="mw-page-title-main">Atomic force microscopy</span> Type of microscopy

Atomic force microscopy (AFM) or scanning force microscopy (SFM) is a very-high-resolution type of scanning probe microscopy (SPM), with demonstrated resolution on the order of fractions of a nanometer, more than 1000 times better than the optical diffraction limit.

Scanning probe microscopy (SPM) is a branch of microscopy that forms images of surfaces using a physical probe that scans the specimen. SPM was founded in 1981, with the invention of the scanning tunneling microscope, an instrument for imaging surfaces at the atomic level. The first successful scanning tunneling microscope experiment was done by Gerd Binnig and Heinrich Rohrer. The key to their success was using a feedback loop to regulate gap distance between the sample and the probe.

<span class="mw-page-title-main">Near-field scanning optical microscope</span>

Near-field scanning optical microscopy (NSOM) or scanning near-field optical microscopy (SNOM) is a microscopy technique for nanostructure investigation that breaks the far field resolution limit by exploiting the properties of evanescent waves. In SNOM, the excitation laser light is focused through an aperture with a diameter smaller than the excitation wavelength, resulting in an evanescent field on the far side of the aperture. When the sample is scanned at a small distance below the aperture, the optical resolution of transmitted or reflected light is limited only by the diameter of the aperture. In particular, lateral resolution of 6 nm and vertical resolution of 2–5 nm have been demonstrated.

Nanophotonics or nano-optics is the study of the behavior of light on the nanometer scale, and of the interaction of nanometer-scale objects with light. It is a branch of optics, optical engineering, electrical engineering, and nanotechnology. It often involves dielectric structures such as nanoantennas, or metallic components, which can transport and focus light via surface plasmon polaritons.

<span class="mw-page-title-main">Characterization (materials science)</span> Study of material structure and properties

Characterization, when used in materials science, refers to the broad and general process by which a material's structure and properties are probed and measured. It is a fundamental process in the field of materials science, without which no scientific understanding of engineering materials could be ascertained. The scope of the term often differs; some definitions limit the term's use to techniques which study the microscopic structure and properties of materials, while others use the term to refer to any materials analysis process including macroscopic techniques such as mechanical testing, thermal analysis and density calculation. The scale of the structures observed in materials characterization ranges from angstroms, such as in the imaging of individual atoms and chemical bonds, up to centimeters, such as in the imaging of coarse grain structures in metals.

Chemical imaging is the analytical capability to create a visual image of components distribution from simultaneous measurement of spectra and spatial, time information. Hyperspectral imaging measures contiguous spectral bands, as opposed to multispectral imaging which measures spaced spectral bands.

Photothermal microspectroscopy (PTMS), alternatively known as photothermal temperature fluctuation (PTTF), is derived from two parent instrumental techniques: infrared spectroscopy and atomic force microscopy (AFM). In one particular type of AFM, known as scanning thermal microscopy (SThM), the imaging probe is a sub-miniature temperature sensor, which may be a thermocouple or a resistance thermometer. This same type of detector is employed in a PTMS instrument, enabling it to provide AFM/SThM images: However, the chief additional use of PTMS is to yield infrared spectra from sample regions below a micrometer, as outlined below.

<span class="mw-page-title-main">Fourier-transform infrared spectroscopy</span> Technique to analyze the infrared spectrum of matter

Fourier-transform infrared spectroscopy (FTIR) is a technique used to obtain an infrared spectrum of absorption or emission of a solid, liquid, or gas. An FTIR spectrometer simultaneously collects high-resolution spectral data over a wide spectral range. This confers a significant advantage over a dispersive spectrometer, which measures intensity over a narrow range of wavelengths at a time.

<span class="mw-page-title-main">Raman microscope</span> Laser microscope used for Raman spectroscopy

The Raman microscope is a laser-based microscopic device used to perform Raman spectroscopy. The term MOLE is used to refer to the Raman-based microprobe. The technique used is named after C. V. Raman, who discovered the scattering properties in liquids.

<span class="mw-page-title-main">Infrared Nanospectroscopy (AFM-IR)</span> Infrared microscopy technique

AFM-IR or infrared nanospectroscopy is one of a family of techniques that are derived from a combination of two parent instrumental techniques. AFM-IR combines the chemical analysis power of infrared spectroscopy and the high-spatial resolution of scanning probe microscopy (SPM). The term was first used to denote a method that combined a tuneable free electron laser with an atomic force microscope equipped with a sharp probe that measured the local absorption of infrared light by a sample with nanoscale spatial resolution.

Tip-enhanced Raman spectroscopy (TERS) is a variant of surface-enhanced Raman spectroscopy (SERS) that combines scanning probe microscopy with Raman spectroscopy. High spatial resolution chemical imaging is possible via TERS, with routine demonstrations of nanometer spatial resolution under ambient laboratory conditions, or better at ultralow temperatures and high pressure.

<span class="mw-page-title-main">Campanile probe</span>

In near-field scanning optical microscopy the campanile probe is a tapered optical probe with a shape of a campanile. It is made of an optically transparent dielectric, typically silica, and its two facets are coated with a metal, typically gold. At the probe tip, the metal-coated facets are separated by a gap of a few tens of nanometers, which determines the spatial resolution of the probe. Such a probe design allows collecting optical signals, usually photoluminescence (PL) or Raman scattering, with a subwavelength resolution, breaking the diffraction limit.

The operation of a photon scanning tunneling microscope (PSTM) is analogous to the operation of an electron scanning tunneling microscope, with the primary distinction being that PSTM involves tunneling of photons instead of electrons from the sample surface to the probe tip. A beam of light is focused on a prism at an angle greater than the critical angle of the refractive medium in order to induce total internal reflection within the prism. Although the beam of light is not propagated through the surface of the refractive prism under total internal reflection, an evanescent field of light is still present at the surface.

<span class="mw-page-title-main">Nano-FTIR</span> Infrared microscopy technique

Nano-FTIR is a scanning probe technique that utilizes as a combination of two techniques: Fourier transform infrared spectroscopy (FTIR) and scattering-type scanning near-field optical microscopy (s-SNOM). As s-SNOM, nano-FTIR is based on atomic-force microscopy (AFM), where a sharp tip is illuminated by an external light source and the tip-scattered light is detected as a function of tip position. A typical nano-FTIR setup thus consists of an atomic force microscope, a broadband infrared light source used for tip illumination, and a Michelson interferometer acting as Fourier-transform spectrometer. In nano-FTIR, the sample stage is placed in one of the interferometer arms, which allows for recording both amplitude and phase of the detected light. Scanning the tip allows for performing hyperspectral imaging with nanoscale spatial resolution determined by the tip apex size. The use of broadband infrared sources enables the acquisition of continuous spectra, which is a distinctive feature of nano-FTIR compared to s-SNOM. Nano-FTIR is capable of performing infrared (IR) spectroscopy of materials in ultrasmall quantities and with nanoscale spatial resolution. The detection of a single molecular complex and the sensitivity to a single monolayer has been shown. Recording infrared spectra as a function of position can be used for nanoscale mapping of the sample chemical composition, performing a local ultrafast IR spectroscopy and analyzing the nanoscale intermolecular coupling, among others. A spatial resolution of 10 nm to 20 nm is routinely achieved.

References

  1. 1 2 Dragnea, Bogdan; Leone, Stephen (2001). "Advances in submicron infrared vibrational band chemical imaging". International Reviews in Physical Chemistry. 20 (1): 59–92. Bibcode:2001IRPC...20...59D. doi:10.1080/01442350010012557. S2CID   9166775.
  2. 1 2 Vobornik, Dušan (2005). Scanning near-field infrared microscopy and spectromicroscopy applied to nano-systems and cells (Thesis). doi:10.5075/epfl-thesis-3296 . Retrieved 15 July 2013.
  3. 1 2 Boerio, F. J.; Starr, M. J. (2008). "AFM/FTIR: A New Technique for Materials Characterization". The Journal of Adhesion. 84 (10): 872–895. doi:10.1080/00218460802445308. S2CID   85439894.
  4. ↑ Oshikane, Yasushi; Kataoka, Toshihiko; Okuda, Mitsuru; Hara, Seiji; Inoue, Haruyuki; Nakano, Motohiro (2007). "Observation of nanostructure by scanning near-field optical microscope with small sphere probe". Science and Technology of Advanced Materials. 8 (3): 181–185. Bibcode:2007STAdM...8..181O. doi: 10.1016/j.stam.2007.02.013 . S2CID   3891418.
  5. 1 2 Webster, S (1998). "Raman microscopy using a scanning near-field optical probe". Vibrational Spectroscopy. 18: 51–59. doi:10.1016/S0924-2031(98)00037-X.
  6. 1 2 Jahncke, C. L.; Paesler, M. A.; Hallen, H. D. (1995). "Raman imaging with near-field scanning optical microscopy". Applied Physics Letters. 67 (17): 2483. Bibcode:1995ApPhL..67.2483J. doi:10.1063/1.114615. S2CID   34846438.
  7. 1 2 Pettinger, Bruno (2010). "Single-molecule surface- and tip-enhanced Raman spectroscopy". Molecular Physics. 108 (16): 2039–2059. Bibcode:2010MolPh.108.2039P. doi:10.1080/00268976.2010.506891. S2CID   220376286.
  8. ↑ J. J. Wang; et al. (2003). "Apertureless near-field Raman spectroscopy". Journal of Microscopy. 210 (3): 330–333. doi:10.1046/j.1365-2818.2003.01166.x. PMID   12787109. S2CID   45902977.
  9. 1 2 Kalkbrenner, T.; Ramstein, M.; Mlynek, J.; Sandoghdar, V. (2001). "A single gold particle as a probe for apertureless scanning near-field optical microscopy". Journal of Microscopy. 202 (Pt 1): 72–76. doi:10.1046/j.1365-2818.2001.00817.x. PMID   11298873. S2CID   33056571.
  10. ↑ Nakata, Toshihiko; Watanabe, Masahiro (2011). "Nanometer-resolution optical probe using a metallic-nanoparticle-intercalated carbon nanotube". Journal of Applied Physics. 109 (1): 013110–013110–5. Bibcode:2011JAP...109a3110N. doi:10.1063/1.3511437.
  11. ↑ Inouye, Yasushi (1999). Jutamulia, Suganda; Ohtsu, Motoichi; Asakura, Toshimitsu (eds.). "Near-field scanning optical microscope using a metallized cantilever tip for nanospectroscopy". Near-Field Optics: Physics. Near-Field Optics: Physics, Devices, and Information Processing. 3791: 40–48. Bibcode:1999SPIE.3791...40I. doi:10.1117/12.363860. S2CID   136975757.
  12. ↑ Anderson, Mark S.; Pike, William T. (2002). "A Raman-atomic force microscope for apertureless-near-field spectroscopy and optical trapping". Review of Scientific Instruments. 73 (3): 1198. Bibcode:2002RScI...73.1198A. doi:10.1063/1.1445864.
  13. ↑ Stöckle, R (2000). "Nanoscale chemical analysis by tip-enhanced Raman spectroscopy". Chemical Physics Letters. 318 (1–3): 131–136. Bibcode:2000CPL...318..131S. doi:10.1016/S0009-2614(99)01451-7.
  14. 1 2 3 4 Bruno Pettinger, Tip-Enhanced Raman Spectroscopy (TERS)
  15. 1 2 Nieman, Linda T.; Krampert, Gerhard M.; Martinez, Robert E. (2001). "An apertureless near-field scanning optical microscope and its application to surface-enhanced Raman spectroscopy and multiphoton fluorescence imaging". Review of Scientific Instruments. 72 (3): 1691. Bibcode:2001RScI...72.1691N. doi:10.1063/1.1347975.
  16. 1 2 Elfick, Alistair P. D.; Downes, Andrew R.; Mouras, Rabah (2009). "Development of tip-enhanced optical spectroscopy for biological applications: A review". Analytical and Bioanalytical Chemistry. 396 (1): 45–52. doi:10.1007/s00216-009-3223-9. PMID   19876621. S2CID   44849038.
  17. 1 2 Chan, K L Andrew; Kazarian, Sergei G (2011). "Tip-enhanced Raman mapping with top-illumination AFM". Nanotechnology. 22 (17): 175701. Bibcode:2011Nanot..22q5701C. doi:10.1088/0957-4484/22/17/175701. PMID   21411920. S2CID   26859123.
  18. 1 2 3 4 5 Masaki, Tatsuhiro; Inouye, Yasushi; Kawata, Satoshi (2004). "Submicron resolution infrared microscopy by use of a near-field scanning optical microscope with an apertured cantilever". Review of Scientific Instruments. 75 (10): 3284–3287. Bibcode:2004RScI...75.3284M. doi:10.1063/1.1784567.
  19. 1 2 Vobornik, D; Margaritondo, G; Sanghera, J; Thielen, P; Aggarwal, I; Ivanov, B; Tolk, N; Manni, V; et al. (2005). "Spectroscopic infrared scanning near-field optical microscopy (IR-SNOM)". Journal of Alloys and Compounds. 401 (1–2): 80–85. doi:10.1016/j.jallcom.2005.02.057.
  20. ↑ Williams, C. C.; Wickramasinghe, H. K. (1986). "Scanning thermal profiler". Applied Physics Letters. 49 (23): 1587. Bibcode:1986ApPhL..49.1587W. doi:10.1063/1.97288.
  21. 1 2 3 Brucherseifer, Martin; Kranz, Christine; Mizaikoff, Boris (2007). "Combined in Situ Atomic Force Microscopy- Infrared-Attenuated Total Reflection Spectroscopy". Analytical Chemistry. 79 (22): 8803–8806. doi:10.1021/ac071004q. PMID   17939644.
  22. ↑ Hecht, Bert; Sick, Beate; Wild, Urs P.; Deckert, Volker; Zenobi, Renato; Martin, Olivier J. F.; Pohl, Dieter W. (2000). "Scanning near-field optical microscopy with aperture probes: Fundamentals and applications". The Journal of Chemical Physics. 112 (18): 7761. Bibcode:2000JChPh.112.7761H. doi:10.1063/1.481382.
  23. ↑ Sands, H. S.; Demangeot, F.; Bonera, E.; Webster, S.; Bennett, R.; Hayward, I. P.; Marchi, F.; Smith, D. A.; et al. (2002). "Development of a combined confocal and scanning near-field Raman microscope for deep UV laser excitation". Journal of Raman Spectroscopy. 33 (9): 730–739. Bibcode:2002JRSp...33..730S. doi:10.1002/jrs.909.
  24. ↑ Verma, Prabhat; Yamada, Kohei; Watanabe, Hiroyuki; Inouye, Yasushi; Kawata, Satoshi (2006). "Near-field Raman scattering investigation of tip effects on C60 molecules". Physical Review B. 73 (4): 045416. Bibcode:2006PhRvB..73d5416V. doi:10.1103/PhysRevB.73.045416.
  25. ↑ Novotny, L.; Pohl, D. W.; Hecht, B. (1995). "Scanning near-field optical probe with ultrasmall spot size". Optics Letters. 20 (9): 970. Bibcode:1995OptL...20..970N. doi:10.1364/OL.20.000970. PMID   19859393.
  26. 1 2 Qian, X.-M.; Nie, S. M. (2008). "Single-molecule and single-nanoparticle SERS: From fundamental mechanisms to biomedical applications". Chemical Society Reviews. 37 (5): 912–20. doi:10.1039/B708839F. PMID   18443676.
  27. ↑ Rendell, R.; Scalapino, D. (1981). "Surface plasmons confined by microstructures on tunnel junctions". Physical Review B. 24 (6): 3276–3294. Bibcode:1981PhRvB..24.3276R. doi:10.1103/PhysRevB.24.3276.
  28. 1 2 3 AFM-microRaman and nanoRamanTM
  29. ↑ [What TERS microscopy can do, SERS cannot What TERS microscopy can do, SERS cannot] Satoshi Kawata Department of Applied Physics, Osaka University, Suita, Osaka and RIKEN, Wako, Saitama, Japan
  30. ↑ Kawata, Satoshi; Inouye, Yasushi; Verma, Prabhat (2009). "Plasmonics for near-field nano-imaging and superlensing". Nature Photonics. 3 (7): 388–394. Bibcode:2009NaPho...3..388K. doi:10.1038/nphoton.2009.111.
  31. ↑ Yano, Taka-aki; Verma, Prabhat; Saito, Yuika; Ichimura, Taro; Kawata, Satoshi (2009). "Pressure-assisted tip-enhanced Raman imaging at a resolution of a few nanometres". Nature Photonics. 3 (8): 473–477. Bibcode:2009NaPho...3..473Y. doi:10.1038/nphoton.2009.74. S2CID   54837097.
  32. ↑ Ichimura, Taro; Hayazawa, Norihiko; Hashimoto, Mamoru; Inouye, Yasushi; Kawata, Satoshi (2004). "Tip-Enhanced Coherent Anti-Stokes Raman Scattering for Vibrational Nanoimaging". Physical Review Letters. 92 (22): 220801. Bibcode:2004PhRvL..92v0801I. doi:10.1103/PhysRevLett.92.220801. PMID   15245207. S2CID   29726570.
  33. ↑ Pettinger B．Topics Appl. Phys., 103, 217–240 (2006)
  34. ↑ L. Rayleigh, Phil. Mag.. 8, 261–274 (1879)
  35. ↑ E.G. van Putten; D. Akbulut; J. Bertolotti; W.L. Vos; A. Lagendijk & A.P. Mosk (2011). "Scattering Lens Resolves Sub-100 nm Structures with Visible Light". Physical Review Letters. 106 (19): 193905. arXiv: 1103.3643 . Bibcode:2011PhRvL.106s3905V. doi:10.1103/PhysRevLett.106.193905. PMID   21668161. S2CID   15793849.
  36. ↑ R. M. Silverstein, G. C. Bassler, T. C. Morill, Spectrometric Identification of Organic Compounds, 5th edition, Wiley, New York (1991) ISBN   0-471-39362-2
  37. ↑ Hammiche, A.; Pollock, H. M.; Reading, M.; Claybourn, M.; Turner, P. H.; Jewkes, K. (1999). "Photothermal FT-IR Spectroscopy: A Step Towards FT-IR Microscopy at a Resolution Better Than the Diffraction Limit". Applied Spectroscopy. 53 (7): 810–815. Bibcode:1999ApSpe..53..810H. doi:10.1366/0003702991947379. S2CID   93359289.
  38. ↑ Hammiche, A.; Bozec, L.; Conroy, M.; Pollock, H. M.; Mills, G.; Weaver, J. M. R.; Price, D. M.; Reading, M.; et al. (2000). "Highly localized thermal, mechanical, and spectroscopic characterization of polymers using miniaturized thermal probes". Journal of Vacuum Science and Technology B. 18 (3): 1322. Bibcode:2000JVSTB..18.1322H. doi:10.1116/1.591381. S2CID   55856483.
  39. 1 2 3 Brehm, Markus; Taubner, Thomas; Hillenbrand, Rainer; Keilmann, Fritz (2006). "Infrared Spectroscopic Mapping of Single Nanoparticles and Viruses at Nanoscale Resolution". Nano Letters. 6 (7): 1307–1310. Bibcode:2006NanoL...6.1307B. doi:10.1021/nl0610836. PMID   16834401.
  40. 1 2 3 Julien Houel; et al. (2007). "Ultraweak-Absorption Microscopy of a Single Semiconductor Quantum Dot in the Midinfrared Range". Physical Review Letters. 99 (21): 217404. Bibcode:2007PhRvL..99u7404H. doi:10.1103/PhysRevLett.99.217404. PMID   18233255. S2CID   13225150.
  41. 1 2 Houel, Julien; Homeyer, Estelle; Sauvage, SéBastien; Boucaud, Philippe; Dazzi, Alexandre; Prazeres, Rui; Ortéga, Jean-Michel (2009). "Midinfrared absorption measured at a λ/400 resolution with an atomic force microscope". Optics Express. 17 (13): 10887–94. Bibcode:2009OExpr..1710887H. doi: 10.1364/OE.17.010887 . PMID   19550489. S2CID   120639500.
  42. ↑ Verity, Jocelyne E.; Chhabra, Neetu; Sinnathamby, Koneswaran; Yip, Christopher M. (2009). "Tracking Molecular Interactions in Membranes by Simultaneous ATR-FTIR-AFM". Biophysical Journal. 97 (4): 1225–1231. Bibcode:2009BpJ....97.1225V. doi:10.1016/j.bpj.2009.06.013. PMC   2726332 . PMID   19686671.
  43. 1 2 3 Kjoller, K; Felts, J R; Cook, D; Prater, C B; King, W P (2010). "High-sensitivity nanometer-scale infrared spectroscopy using a contact mode microcantilever with an internal resonator paddle". Nanotechnology. 21 (18): 185705. Bibcode:2010Nanot..21r5705K. doi:10.1088/0957-4484/21/18/185705. PMID   20388971. S2CID   27042137.
  44. 1 2 3 4 5 Craig Prater, Kevin Kjoller, Debra Cook, Roshan Shetty, Gregory Meyers, Carl Reinhardt, Jonathan Felts, William King, Konstantin Vodopyanov and Alexandre Dazzi, Nanoscale Infrared Spectroscopy of Materials by Atomic Force Microscopy [ permanent dead link ]Microscopy and Analysis, 24, 5–8 (2010)
  45. 1 2 Yarrow, Fiona; Kennedy, Eamonn; Salaun, Frederic; Rice, James H. (2010). "Sub-wavelength infrared imaging of lipids". Biomedical Optics Express. 2 (1): 37–43. doi:10.1364/BOE.2.000037. PMC   3028496 . PMID   21326633.
  46. 1 2 Ruggeri, Francesco Simone; Mannini, Benedetta; Schmid, Roman; Vendruscolo, Michele; Knowles, Tuomas P. J. (2020-06-10). "Single molecule secondary structure determination of proteins through infrared absorption nanospectroscopy". Nature Communications. 11 (1): 2945. Bibcode:2020NatCo..11.2945R. doi:10.1038/s41467-020-16728-1. ISSN   2041-1723. PMC   7287102 . PMID   32522983.
  47. 1 2 Rice, James H. (2010). "Nanoscale optical imaging by atomic force infrared microscopy" (PDF). Nanoscale. 2 (5): 660–7. Bibcode:2010Nanos...2..660R. doi:10.1039/b9nr00279k. hdl:10197/4463. PMID   20648306.
  48. ↑ Bethe, H. (1944). "Theory of Diffraction by Small Holes". Physical Review. 66 (7–8): 163–182. Bibcode:1944PhRv...66..163B. doi:10.1103/PhysRev.66.163.
  49. ↑ C. J. Bouwkamp, Philips Res. Rep., 5, 321–332 (1950)
  50. ↑ Cricenti, A.; Generosi, R.; Perfetti, P.; Gilligan, J. M.; Tolk, N. H.; Coluzza, C.; Margaritondo, G. (1998). "Free-electron-laser near-field nanospectroscopy". Applied Physics Letters. 73 (2): 151. Bibcode:1998ApPhL..73..151C. doi:10.1063/1.121739.
  51. ↑ Glotin, F (1998). "Activities of the CLIO infrared facility". Nuclear Instruments and Methods in Physics Research Section B: Beam Interactions with Materials and Atoms. 144 (1–4): 8–17. Bibcode:1998NIMPB.144....8G. doi:10.1016/S0168-583X(98)00293-6.
  52. ↑ Tanimura, Takahito; Akamatsu, Daisuke; Yokoi, Yoshihiko; Furusawa, Akira; Kozuma, Mikio (2006). "Generation of a squeezed vacuum resonant on a rubidium D1 line with periodically poled KTiOPO4". Optics Letters. 31 (15): 2344–6. arXiv: quant-ph/0603214 . Bibcode:2006OptL...31.2344T. doi:10.1364/OL.31.002344. PMID   16832480. S2CID   18700111.
  53. ↑ Sanghera, J. S., and Aggarwal, I. D., Infrared Fiber Optics (Boca Raton; Florida: CRC) 1998
  54. ↑ Mossadegh, R.; Sanghera, J.S.; Schaafsma, D.; Cole, B.J.; Nguyen, V.Q.; Miklos, R.E.; Aggarwal, I.D. (1998). "Fabrication of single-mode chalcogenide optical fiber". Journal of Lightwave Technology. 16 (2): 214–217. Bibcode:1998JLwT...16..214M. doi:10.1109/50.661012.
  55. ↑ Lahrech, A.; Bachelot, R.; Gleyzes, P.; Boccara, A. C. (1997). "Infrared near-field imaging of implanted semiconductors: Evidence of a pure dielectric contrast". Applied Physics Letters. 71 (5): 575. Bibcode:1997ApPhL..71..575L. doi:10.1063/1.119798. S2CID   11004387.
  56. 1 2 Jordan, Claire E.; Stranick, Stephan J.; Richter, Lee J.; Cavanagh, Richard R. (1999). "Removing optical artifacts in near-field scanning optical microscopy by using a three-dimensional scanning mode". Journal of Applied Physics. 86 (5): 2785. Bibcode:1999JAP....86.2785J. doi:10.1063/1.371126.
  57. ↑ Cricenti, A.; Generosi, R.; Barchesi, C.; Luce, M.; Rinaldi, M. (1998). "A multipurpose scanning near-field optical microscope: Reflectivity and photocurrent on semiconductor and biological samples". Review of Scientific Instruments. 69 (9): 3240. Bibcode:1998RScI...69.3240C. doi:10.1063/1.1149089.
  58. ↑ Pethica, J B; Oliver, W C (1987). "Tip Surface Interactions in STM and AFM". Physica Scripta. T19A: 61–66. Bibcode:1987PhST...19...61P. doi:10.1088/0031-8949/1987/T19A/010. S2CID   250806412.
  59. 1 2 Palmer, R; Dittmar, R (1993). "Step-scan FT-IR photothermal spectral depth profiling of polymer films". Thin Solid Films. 223 (1): 31–38. Bibcode:1993TSF...223...31P. doi:10.1016/0040-6090(93)90724-4.
  60. ↑ Anderson, Mark S. (2000). "Infrared Spectroscopy with an Atomic Force Microscope". Applied Spectroscopy. 54 (3): 349–352. Bibcode:2000ApSpe..54..349A. doi:10.1366/0003702001949618. S2CID   95187852.
  61. ↑ Sun, W. X.; Shen, Z. X. (2003). "Near-field scanning Raman microscopy using apertureless probes". Journal of Raman Spectroscopy. 34 (9): 668–676. Bibcode:2003JRSp...34..668S. doi:10.1002/jrs.1063.
  62. ↑ Grausem, J.; Humbert, B.; Burneau, A.; Oswalt, J. (1997). "Subwavelength Raman spectroscopy". Applied Physics Letters. 70 (13): 1671. Bibcode:1997ApPhL..70.1671G. doi:10.1063/1.118665.
  63. ↑ Dragnea, Bogdan; Preusser, Jan; Schade, Wolfgang; Leone, Stephen R.; Hinsberg, William D. (1999). "Transmission near-field scanning microscope for infrared chemical imaging". Journal of Applied Physics. 86 (5): 2795. Bibcode:1999JAP....86.2795D. doi:10.1063/1.371127. S2CID   12908935.
  64. ↑ Webster, S.; Batchelder, D. N.; Smith, D. A. (1998). "Submicron resolution measurement of stress in silicon by near-field Raman spectroscopy". Applied Physics Letters. 72 (12): 1478. Bibcode:1998ApPhL..72.1478W. doi:10.1063/1.120598.
  65. ↑ Akhremitchev, Boris B.; Pollack, Steven; Walker, Gilbert C. (2001). "Apertureless Scanning Near-Field Infrared Microscopy of a Rough Polymeric Surface". Langmuir. 17 (9): 2774–2781. doi:10.1021/la001401v.
  66. ↑ Hayazawa, N (2000). "Metallized tip amplification of near-field Raman scattering". Optics Communications. 183 (1–4): 333–336. Bibcode:2000OptCo.183..333H. doi:10.1016/S0030-4018(00)00894-4.
  67. ↑ Masaki, Tatsuhiro (2004). "Near-field infrared imaging of molecular changes in cholesteryl oleate by free electron laser infrared ablation". Journal of Applied Physics. 95 (1): 334–338. Bibcode:2004JAP....95..334M. doi:10.1063/1.1628380.
  68. ↑ Mayet, Celine; Dazzi, Alexandre; Prazeres, Rui; Ortega, Jean-Michel; Jaillard, Danielle (2010). "In situ identification and imaging of bacterial polymer nanogranules by infrared nanospectroscopy". The Analyst. 135 (10): 2540–5. Bibcode:2010Ana...135.2540M. doi:10.1039/C0AN00290A. PMID   20820491.
  69. ↑ E. Romano, S. Trabattoni, M. Campione, E. Merati, A. Sassella and D. Narducci Combined use of AFM and FTIR in the analysis of the hydrogen termination of Si(100) surfaces Microscopy: Science, Technology, Applications and Education, A. Méndez-Vilas and J. Diaz (Eds.), Vol. 3, pp. 1984–1992 (2010) ISBN   978-84-614-6191-2
  70. ↑ McDonough, Laurie A.; Dragnea, Bogdan; Preusser, Jan; Leone, Stephen R.; Hinsberg, William D. (2003). "Water Vapor Uptake in Photolithographic Polymers Observed by Infrared Near-Field Scanning Optical Microscopy in a Controlled Environment". The Journal of Physical Chemistry B. 107 (21): 4951–4954. doi:10.1021/jp022489j. S2CID   18265192.
This page is based on this Wikipedia article
Text is available under the CC BY-SA 4.0 license; additional terms may apply.
Images, videos and audio are available under their respective licenses.