Bonomi BS.10 Ardea

Last updated
BS.10 Ardea
RoleSingle seat competition glider
National origin Italy
Manufacturer Aeronautica Bonomi
Designer Camillo Silva
First flight1934
Number built1

The Bonomi BS.10 Ardea (English: Great Heron) was an Italian single seat high performance glider, designed and built in the mid-1930s. Only one was built.

Contents

Design and development

The BS.10 Ardea was an attempt to improve upon the popular BS.2 Balestrucchio of 1932. Like the Balestruccio, the Ardea was a high gull wing aircraft but with increased span and aspect ratio and less gull dihedral. The two spar wing was built from three panels, the straight edged central one having constant chord. The outer panels straight tapered to elliptical tips, with trailing edges entirely occupied by ailerons. The outer ends of the centre section were braced, as on some other Bonomi gliders, with a pair of faired, asymmetric steel V-struts, mounted on the lower fuselage immediately below the forward wing spar. The wing was mounted over the fuselage on a short, faired pedestal. [1]

The Ardea had a deep sided, hexagonal cross-section fuselage, entirely plywood skinned. Its pilot sat in a small, deep cockpit, head against the front of the pedestal and partly protected from the airstream by the upper fuselage panels, which both lifted off for entry. There was a conventional single skid undercarriage under the forward fuselage aft to the wing trailing edge, with a small tailskid. The fuselage tapered gently to the tail, where a large, roughly elliptical balanced rudder, mounted on a much smaller fin, extended down to the keel. The Ardea's balanced elevators together formed a slender ellipse in plan, though with a cut-out for rudder movement. [1]

The BS.10 flew for the first time in 1934, [1] and was first registered in September of that year. By November it was registered to the Royal Italian Aero Club, Rome. [2] Only one was built.


Specifications

Data from Pedrielli (2011) p.87 [1]

General characteristics

Performance


Related Research Articles

The CVV1 Pinguino was a single seat, high performance glider designed and built in Italy in the mid-1930s, the first of a series of gliders from the Milan Polytechnic. It did not go into production.

The CVV 2 Asiago is a simple, single seat glider designed and built in Italy in the mid-1930s, the second of a series of gliders from the Milan Polytechnic and the first go into production.

The Bonomi BS.2 Balestruccio was an Italian sailplane designed to set records. In 1932 it set a new national endurance record with a flight of over 25 minutes.

The Bonomi BS.8 Biancone was a single-seat training glider designed and built in Italy in the 1930s. It was developed from the Bonomi BS.7 Allievo Italia primary glider.

The Bonomi BS.14 Astore was a two-seat training and aerobatic glider, designed and built in Italy in 1935. Only one was constructed.

Bonomi BS.17 Allievo Cantù

The Bonomi BS.17 Allievo Cantù was a single seat training glider, designed and built in Italy in 1934 and widely used by flying clubs.

The Bonomi BS.18 Airone was a single seat training glider, designed in Italy in 1936. Only one was built.

The Bonomi BS.19 Alca was a single seat, tractor configuration motor glider, designed and built in Italy shortly before World War II. It had an unusual retractable undercarriage used only for take-offs. Only one was built.

The Bonomi BS.22 Alzavola was a training motor glider, intended to acquaint capable glider pilots with the characteristics of powered aircraft. The sole example was designed and built in Italy in the late 1930s.

The Bonomi BS.24 Biposto Rome was an Italian dual control trainer designed for club use. Six were built in the mid-1930s.

The Bonomi BS.28 Alcione, sometimes known as the Lombarda BS.28 Alcione, was a single seat competition sailplane designed and built in Italy in 1937-8. About four were completed, with two more or less refined fuselages.

The Tedeschi E.T.186 was a simple, single seat training glider built in Italy and first flown in 1947. Only one was constructed.

The Pagliani Vittoria was a single-seat glider built in Italy during Second World War. Only one was constructed.

The Sala N1 or N1 Sala was a single-seat,18 m span competition glider built in Italy in 1937. Only one was constructed.

The Teichfuss Falco was an Italian single-seat, intermediate-performance glider, designed by Luigi Teichfuss and flown in 1931.

The Teichfuss Orione was an Italian high performance single seat glider, designed by Luigi Teichfuss. It made a six-hour record flight and also flew as the Italian representative at the 1936 Olympics.

The Teichfuss Supergrifo or Super Grifo was an Italian competition glider designed by Luigi Teichfuss and flown in 1935. Only one was built.

The Teichfuss Turbine was an Italian single seat high performance glider, designed by Luigi Teichfuss and flown in 1939.

The Teichfuss Borea or LT.35 Borea was an Italian high performance glider designed by Luigi Teichfuss. It was completed by 1943 but never flew and the sole example was destroyed during the German occupation of Italy.

The CAT 28BP was an Italian development of the licence built Dittmar Condor II into a high performance tandem two seat glider. Built in 1938, it anticipated the post-war, two seat Dittmar Condor IV and held the Italian national distance record for many years.

References

  1. 1 2 3 4 Pedrielli, Vincenzo; Camastra, Francesco (2011). Italian Vintage Sailplanes. Königswinter: EQIP Werbung & Verlag GmbH. pp. 86–87. ISBN   978 3 9808838 9 4.
  2. ↑ Air Britain: pre-war Italian register (Malcolm Fillmore)
  3. ↑ Zuerl, Hubert (1941). Segelflug im Wettbewerb der Völker. Berlin: E. S. Mittler & Sohn. pp. 38, 42.
This page is based on this Wikipedia article
Text is available under the CC BY-SA 4.0 license; additional terms may apply.
Images, videos and audio are available under their respective licenses.