Bonomi BS.18 Airone

Last updated
BS.18 Airone
Role Training glider
National origin Italy
Manufacturer Aeronautica Bonomi
Designer Camillo Silva
First flight1936
Number built1

The Bonomi BS.18 Airone (English: Heron ) was a single seat training glider, designed in Italy in 1936. Only one was built.

Contents

Design and development

The Airone was an attempt to produce a training glider similar to the BS.8 Biancone but with a better glide ratio. [1] It used the wings of the Biancone but had the more refined fuselage of the BS.10 Ardea. [2] The wing bracing and the empennage was new. [1]

The wing was a wooden two spar structure, largely fabric covered. The forward spar was close to the leading edge; from it forward around the edge the wing was plywood covered, forming a torque-resistant D-box; aft the covering was fabric. The rear spar was just behind mid-chord. The central panel, occupying a little under half the span, was straight edged and had constant chord. Outboard the wing was straight tapered to rounded tips, ailerons occupying all the trailing edge. The centre section was supported by a low fuselage pedestal and braced on each side with a parallel pair of steel struts. These were fixed to the two spars close to the outer ends of the centre panels and to the lower fuselage. [1]

The Airone had a deep sided, hexagonal cross-section fuselage, entirely plywood skinned. Its pilot sat in a small, deep cockpit, head against the front of the pedestal and partly protected from the airstream by the upper fuselage panels, which both lifted off for entry. There was a conventional single skid undercarriage under the forward fuselage aft to the wing trailing edge, with a small tailskid. The fuselage tapered gently to the tail, where the horizontal surfaces, braced and straight edged but with elliptical tips were mounted on top of a short fin. The elevators used a thick aerofoil for efficiency and had a cut-out for the balanced rudder. This was large, extending down to the keel with straight edges and rounded corners. [1]

The BS.18 Airone first flew in 1936 but only one was built. [1]

Specifications

Data from Pedrielli (2011) p.97 [1]

General characteristics

Performance

Related Research Articles

The CVV 2 Asiago is a simple, single seat glider designed and built in Italy in the mid-1930s, the second of a series of gliders from the Milan Polytechnic and the first go into production.

The Bonomi BS.4 Basettino was a primary glider designed and built in Italy in the 1930s.

The Bonomi BS.5 Ballerina was a single seat, medium performance training glider designed and built in Italy in the 1930s.

<span class="mw-page-title-main">Bonomi BS.7 Allievo Italia</span> Type of aircraft

The Bonomi BS.7 Allievo Italia was a single seat, primary glider designed and built in Italy in the 1920s.

The Bonomi BS.8 Biancone was a single-seat training glider designed and built in Italy in the 1930s. It was developed from the Bonomi BS.7 Allievo Italia primary glider.

The Bonomi BS.10 Ardea was an Italian single seat high performance glider, designed and built in the mid-1930s. Only one was built.

The Bonomi BS.11 Milano and BS.12 Roma were primary gliders designed and built in Italy in the 1930s. Only about six were produced.

The Bonomi BS.14 Astore was a two-seat training and aerobatic glider, designed and built in Italy in 1935. Only one was constructed.

The Bonomi BS.15 Bigiarella, originally named the Bonomi BS.6 Bigiarella was a single seat glider, designed and built in Italy in 1934. Only three were constructed.

<span class="mw-page-title-main">Bonomi BS.17 Allievo Cantù</span> Type of aircraft

The Bonomi BS.17 Allievo Cantù was a single seat training glider, designed and built in Italy in 1934 and widely used by flying clubs.

The Bonomi BS.24 Biposto Rome was an Italian dual control trainer designed for club use. Six were built in the mid-1930s.

The Bonomi BS.28 Alcione, sometimes known as the Lombarda BS.28 Alcione, was a single seat competition sailplane designed and built in Italy in 1937-8. About four were completed, with two more or less refined fuselages.

The Aviomilano CPV1, also known as the Arlecchino, was an Italian high performance sailplane built in the early 1960s. Only one was built.

The Tedeschi E.T.186 was a simple, single seat training glider built in Italy and first flown in 1947. Only one was constructed.

The Pagliani Vittoria was a single-seat glider built in Italy during Second World War. Only one was constructed.

The Sala N1 or N1 Sala was a single-seat,18 m span competition glider built in Italy in 1933. Only one was constructed.

The GP1 was an Italian glider constructed by university students in Pavia in 1925. Only one was built.

The Teichfuss Falco was an Italian single-seat, intermediate-performance glider, designed by Luigi Teichfuss and flown in 1931.

The Teichfuss Grifo was an Italian training glider designed by Luigi Teichfuss and flown in 1934. It was built in small numbers.

<span class="mw-page-title-main">Rubik R-03 Szittya I</span> Type of aircraft

The Rubik R-03 Szittya I was a Hungarian single-seat sailplane flown in the late 1930s. The design was developed through three improving variants. though only one of each was built.

References

  1. 1 2 3 4 5 6 Pedrielli, Vincenzo; Camastra, Francesco (2011). Italian Vintage Sailplanes. Königswinter: EQIP Werbung & Verlag GmbH. pp. 82–3, 86–7, 96–7. ISBN   9783980883894.
  2. 1 2 Zuerl, Hubert (1941). Segelflug im Wettbewerb der Völker. Berlin: E. S. Mittler & Sohn. pp. 38, 42.
This page is based on this Wikipedia article
Text is available under the CC BY-SA 4.0 license; additional terms may apply.
Images, videos and audio are available under their respective licenses.