| BS.7 Allievo Italia | |
|---|---|
 | |
| Role | Intermediate primary glider |
| National origin | Italy |
| Manufacturer | Aeronautica Bonomi |
| Designer | Camillo Silva |
| First flight | 1929 |
| Number built | 8 or less |
The Bonomi BS.7 Allievo Italia (English: Italy student) was a single seat, primary glider designed and built in Italy in the 1920s.
The BS.7 was a primary glider in the Zögling tradition, with high wing and tail, the wings held above the pilot on a flat frame. Its wing and tail surfaces were very close to those of the much copied German glider. It was, though, structurally cleaner and simpler to rig, with most flying wires replaced by faired, steel V-form bracing struts and an empennage supported on a simple box beam rather than an extended central frame. [1] [2]
The extremely simple wing of the BS.7 was built around two spars, one close to the leading edge and the other near mid-chord. The upper ends of the bracing struts were attached to the underside of the spars at about 40% span and to the upper fuselage, at a position directly beneath the forward spar. There was only one bracing wire on each side, running from the top of the forward wing strut to the centre of the upper fuselage just aft of the trailing edge. The fabric covered wing was rectangular in plan apart from the aileron tips, which were obliquely cropped. It was mounted above the fuselage on a trapezoidal frame formed from three struts in a distorted, inverted N-shaped arrangement, the rear member sloping shallowly aft. [1]
The fuselage was a triangular cross-section, plywood covered box beam, inclined upwards to place the triangular tailplane at the same height as the wing, strut braced on top of a trapezoidal fin. The fin carried a deep, unbalanced rudder, rectangular except at the bottom where it was cropped to match the bottom line of the beam. It worked in a notch between the two otherwise rectangular elevators, also unbalanced. The completely exposed pilot's seat was on the upper surface of the forward end of the beam, just under the leading edge, where a narrower forward extension carried the rudder bar and, on its underside, the front end of a landing skid that reached below and behind the pilot. [1]
The BS.7 was designed with transportability in mind and, with the wings detached and arranged along the fuselage beam, leading edges up, it could be towed behind a motorcycle on a two-wheeled trailer. Pilots could use it to gain their A and B badges. [1]
Though the first flight was in 1929, [1] the first BS.7s built did not appear on the Italian civil aircraft register until 1932. [3] The number built is uncertain; Pedrielli states three, but eight appear on the reconstructed register. [1] [3]
Data from Pedrielli (2011) p.81 [1]
General characteristics
Performance
The ESG Grunau 9, later known as the ESG 29 and post-1933 as the DFS 108-10, was one of the first primary gliders, built in Germany from the late 1920s. It was widely sold.
The Bonomi BS.4 Basettino was a primary glider designed and built in Italy in the 1930s.
The Bonomi BS.8 Biancone was a single-seat training glider designed and built in Italy in the 1930s. It was developed from the Bonomi BS.7 Allievo Italia primary glider.
The Bonomi BS.10 Ardea was an Italian single seat high performance glider, designed and built in the mid-1930s. Only one was built.
The Bonomi BS.11 Milano and BS.12 Roma were primary gliders designed and built in Italy in the 1930s. Only about six were produced.
The Bonomi BS.14 Astore was a two-seat training and aerobatic glider, designed and built in Italy in 1935. Only one was constructed.
The Bonomi BS.16 Allievo Bonomi was a single seat primary glider, designed and built in Italy in 1930 and widely used by flying clubs.
The Bonomi BS.17 Allievo Cantù was a single seat training glider, designed and built in Italy in 1934 and widely used by flying clubs.
The Bonomi BS.18 Airone was a single seat training glider, designed in Italy in 1936. Only one was built.
The Bonomi BS.24 Biposto Rome was an Italian dual control trainer designed for club use. Six were built in the mid-1930s.
The CAT 15 was a single-seat primary glider built in Italy just before the Second World War. Only one was constructed.
The Teichfuss Tenax was an Italian, one-off, single seat glider, designed and built by Luigi Treichfuss in 1926 and influenced by German developments.
The Teichfuss LT.12 Biposto was an Italian tandem seat primary glider designed by Luigi Teichfuss and flown in 1933.
The Teichfuss Grifo was an Italian training glider designed by Luigi Teichfuss and flown in 1934. It was built in small numbers.
The Teichfuss Supergrifo or Super Grifo was an Italian competition glider designed by Luigi Teichfuss and flown in 1935. Only one was built.
The Teichfuss Cicogna was an Italian tailless single-seat motor glider designed by Luigi Teichfuss and flown in 1936.
The Teichfuss Astore was an Italian Intermediate single-seat trainer glider designed by Luigi Teichfuss and flown in 1936. Two were built.
The Teichfuss Allievo Pavullo was an Italian single seat open frame primary glider, designed by Luigi Teichfuss of Pavullo and first flown in 1940. It was sold in two versions, strut and cable braced. A single two seat variant was also built.
The Teichfuss Condor II was designed to compete in the first Italian glider contest, held at Asiago in 1924. It was bought on arrival by the official Italian organization as the FIDA TIPO LT N2 but was lost in a mid-contest crash.
The Fabris Febo Paglierini was an Italian sailplane designed to compete in the first Italian International Competition, held in Asiago in 1924. It was one of he better national entrants, all of which were outclassed by the Germans.
