Bonomi BS.28 Alcione

Last updated
BS.28 Alcione
RoleCompetition sailplane
National origin Italy
Manufacturer Aeronautica Bonomi
Designer Camillo Silva
First flightc.1938
Number builtc.4

The Bonomi BS.28 Alcione (English: Halcyon or Kingfisher ), sometimes known as the Lombarda BS.28 Alcione, was a single seat competition sailplane designed and built in Italy in 1937-8. About four were completed, with two more or less refined fuselages.

Contents

Design and development

The Alcione was the last of many gliders designed by Camillo Silva at Aeronautica Benomi, [1] as the latter was taken over in 1937 by Aeronautica Lombarda. [2] The change of ownership led to the Alcione being referred to as both a Bonomi and a Lombarda. Silva designed at least one further glider for Lombarda, the AL-3 [3] which was one of two Italian competitors in the 1939 Olympic Sailplane Competition of 1939. [4]

The Alcione was a refined sailplane in its day, designed in collaboration with the Polytechnic University of Milan. It was a cantilever mid-wing monoplane, its wing built around a single spar at about one third chord. Forward of the spar the wing was plywood covered, forming a torque resisting D-box; elsewhere it was fabric covered. In plan the wings were straight tapered to rounded tips. [5] The whole trailing edge of each wing was moveable, the inner third acting as camber changing air brakes and the rest as differential ailerons. [6] Spoilers of the early, single action Centro Volo a Vela (CVV) type were mounted on the upper wing surface immediately behind the spar and at about one quarter span. [5] [6]

Two different fuselages were built for the Alciones. Both had the same general form, deep under the cockpit which was placed forward of the wing leading edge under an enclosing canopy. There was a short landing skid, ending aft at a semi-recessed wheel at about mid chord. However, one fuselage type had a hexagonal cross-section and the other was better shaped aerodynamically as an ovoid. The latter was lower along the dorsal line, so the other's glazed cockpit cover was lengthened aft with a ply covered extension including small side windows. The lower line also required the addition of a very short pedestal for the tailplane, directly mounted onto the hexagonal fuselage. The horizontal tail was straight tapered and round tipped, placed with its trailing edge in line with that of a narrow fin so that no cut-out for rudder movement was needed. On the ovoid fuselage version with its small pedestal the fin reached only about halfway to the top of the rudder, allowing the inclusion of an aerodynamic balance. On the other fuselage the fin continued upwards to the rudder tip. The rudder itself was broad and D-shaped. There was a little tail bumper on the fuselage keel at the rudder's foot. [5]

The ovoid fuselage version became known as the B.28 Aerodinamico. [7]

The Alcione dates from either 1937 [6] or 1938, [5] with registration dates [8] supporting the latter. Images [5] identify three examples and the register a fourth. [8]

Operational history

An Alcione took part in the Asiago Gliding Competition of 1938. [5]


Specifications

Data from Pedrielli (2011) p.107 [5]

General characteristics

Performance


Related Research Articles

The Ciani EC.41/64 Crib or SSVV EC.41/64 Crib was a single seat, high performance glider designed and built in Italy in the 1960s. Only one was built.

The CVV 2 Asiago is a simple, single seat glider designed and built in Italy in the mid-1930s, the second of a series of gliders from the Milan Polytechnic and the first go into production.

The Bonomi BS.2 Balestruccio was an Italian sailplane designed to set records. In 1932 it set a new national endurance record with a flight of over 25 minutes.

The Aeronautica Lombarda AL-3 was an Italian sailplane, designed and built in 1939 to take part in the Olympic sailplane competition. It did so but was not successful.

The Bonomi BS.4 Basettino was a primary glider designed and built in Italy in the 1930s.

The Bonomi BS.5 Ballerina was a single seat, medium performance training glider designed and built in Italy in the 1930s.

<span class="mw-page-title-main">Bonomi BS.7 Allievo Italia</span> Type of aircraft

The Bonomi BS.7 Allievo Italia was a single seat, primary glider designed and built in Italy in the 1920s.

The Bonomi BS.8 Biancone was a single-seat training glider designed and built in Italy in the 1930s. It was developed from the Bonomi BS.7 Allievo Italia primary glider.

The Bonomi BS.9 Bertina II was a single seat glider with a layout somewhere between that of a flying wing and the conventional, tail stabilized arrangement. A single example was designed and built in Italy in the 1930s.

The Bonomi BS.10 Ardea was an Italian single seat high performance glider, designed and built in the mid-1930s. Only one was built.

The Bonomi BS.11 Milano and BS.12 Roma were primary gliders designed and built in Italy in the 1930s. Only about six were produced.

The Bonomi BS.14 Astore was a two-seat training and aerobatic glider, designed and built in Italy in 1935. Only one was constructed.

The Bonomi BS.16 Allievo Bonomi was a single seat primary glider, designed and built in Italy in 1930 and widely used by flying clubs.

<span class="mw-page-title-main">Bonomi BS.17 Allievo Cantù</span> Type of aircraft

The Bonomi BS.17 Allievo Cantù was a single seat training glider, designed and built in Italy in 1934 and widely used by flying clubs.

The Bonomi BS.18 Airone was a single seat training glider, designed in Italy in 1936. Only one was built.

The Bonomi BS.19 Alca was a single seat, tractor configuration motor glider, designed and built in Italy shortly before World War II. It had an unusual retractable undercarriage used only for take-offs. Only one was built.

The Bonomi BS.24 Biposto Rome was an Italian dual control trainer designed for club use. Six were built in the mid-1930s.

The Bazzocchi EB.1 Littore was a one off, Italian single seat trainer glider designed and built by a university student in 1936.

The Caproni Vizzola MF and 2 were single-seat gliders built in Italy just before World War II. Intended as training aircraft capable of aerobatics, the two variants differed only in their fuselages. Only one of each was built, but they were both successful in Italian competitions.

The Teichfuss Astore was an Italian Intermediate single-seat trainer glider designed by Luigi Teichfuss and flown in 1936. Two were built.

References

  1. ↑ Pedrielli, Vincenzo; Camastra, Francesco (2011). Italian Vintage Sailplanes. Königswinter: EQIP Werbung & Verlag GmbH. pp. 72–107. ISBN   9783980883894.
  2. ↑ Thompson, Jonathan (1963). Italian Civil and Military Aircraft 1930-1945 . Fallbrook, California: Aero Publishers, Inc. p.  293.
  3. ↑ Pedrielli. Italian Vintage Sailplanes. p. 67.
  4. ↑ Simons, Martin (2006). Sailplanes 1920-1945 (2nd revised ed.). Königswinter: EQIP Werbung & Verlag GmbH. pp. 198–9. ISBN   3 9806773 4 6.
  5. 1 2 3 4 5 6 7 Pedrielli. Italian Vintage Sailplanes. pp. 106–107.
  6. 1 2 3 4 Zuerl, Hubert (1941). Segelflug im Wettbewerb der Völker. Berlin: E. S. Mittler & Sohn. p. 42.
  7. ↑ "Bonomi BS.28 Aerodinamico" . Retrieved 1 January 2014.
  8. 1 2 Air Britain: pre-war Italian register (Malcolm Fillmore)
This page is based on this Wikipedia article
Text is available under the CC BY-SA 4.0 license; additional terms may apply.
Images, videos and audio are available under their respective licenses.